Installation Guide

ManualsBrandsLeviton ManualsSmart HomeDecora Smart with Z-Wave Technology 15 Amp Switch, White/Light Almond

LIMITED 5 YEAR WARRANTY AND EXCLUSIONS

Leviton warrants to the original consumer purchaser and not for the beneﬁt of anyone else that

this product at the time of its sale by Leviton is free of defects in materials and workmanship under

normal and proper use for ﬁve years from the purchase date. Leviton’s only obligation is to correct

such defects by repair or replacement, at its option. For details visit www.leviton.com or call

1-800-824-3005. This warranty excludes and there is disclaimed liability for labor for removal of

this product or reinstallation. This warranty is void if this product is installed improperly or in an

improper environment, overloaded, misused, opened, abused, or altered in any manner, or is

not used under normal operating conditions or not in accordance with any labels or instructions.

There are no other or implied warranties of any kind, including merchantability and ﬁtness

for a particular purpose, but if any implied warranty is required by the applicable jurisdiction, the

duration of any such implied warranty, including merchantability and ﬁtness for a particular purpose,

is limited to ﬁve years. Leviton is not liable for incidental, indirect, special, or consequential

damages, including without limitation, damage to, or loss of use of, any equipment, lost

sales or proﬁts or delay or failure to perform this warranty obligation. The remedies provided

herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise

DI-000-DZ15S-02A

FOR CANADA ONLY

For warranty information and/or product returns, residents of Canada should contact Leviton in

writing at Leviton Manufacturing of Canada Ltd to the attention of the Quality Assurance

Department, 165 Hymus Blvd, Pointe-Claire (Quebec), Canada H9R 1E9 or by telephone at

1-800-405-5320.

Decora is a registered trademark of of Leviton Manufacturing Co., Inc.

Z-Wave and Z-Wave Plus are registered trademarks of Sigma Designs and its subsidiaries in the

United States and other countries. Use herein of third party trademarks, service marks, trade names,

brand names and/or product names are for informational purposes only, are/may be the trademarks

of their respective owners; such use is not meant to imply afﬁliation, sponsorship, or endorsement.

No part of this document may be reproduced, transmitted or transcribed without the express

written permission of Leviton Manufacturing Co., Inc.

PATENTS

This product is covered by U.S. Patent No. 8,664,886 and corresponding foreign patents.

TECHNICAL SUPPORT

For additional information contact Leviton’s Technical Support at:

1-800-824-3005 or visit Leviton’s website at www.leviton.com

INSTALLATION INSTRUCTIONS

Switch with Z-Wave

Technology

Cat. No. DZ15S

Universal Electronic Switch

Rated: 120/277 VAC, 60 Hz

1800W Incandescent

5A, 600W LED/CFL

15A (120 VAC) Fluorescent

8A (277 VAC) Fluorescent

15A Resistive

1/2 HP Motor

Turn lights or

motor loads

on/off from

anywhere using

a compatible

Z-Wave

controller

decora smart™

Testing your Switch prior to mounting in

wall box:

Switch Mounting:

TURN OFF POWER AT

CIRCUIT BREAKER OR FUSE.

• Restore power at circuit

breaker or fuse.

• Press pad until locator light is

OFF. Lights should turn ON.

If lights do not turn ON, refer

to the TROUBLESHOOTING

section.

Step 5

• Position all wires to provide

room in outlet wall box for

device.

• Ensure that the word "TOP" is

facing up on device strap.

• Partially screw in mounting

screws in wall box mounting

holes.

NOTE: Dress wires with a

bend as shown in diagram in

order to relieve stress when

mounting device.

Step 6

Installation may now be

completed by tightening

mounting screws into wall box.

Attach wallplate.

Restore Power:

Restore power at circuit breaker or fuse.

Installation is complete.

Step

NOTE: The locator light will illuminate when the load is in the

OFF position to facilitate access in the dark.

Rocker Pad (Default settings)

Turn ON from OFF position:

Tap top of rocker – Lights turn ON.

Turn OFF from ON position:

Tap bottom of rocker – Lights turn OFF.

If there is a power outage, when the power is restored, the lights

will return to the last setting before the power interruption.

Cleaning: Clean with a damp cloth. DO NOT use chemical

cleaners.

OPERATION

Rocker

Locator

Light

INCLUSION TO A Z-WAVE

NETWORK

Leviton Decora Smart

Z-Wave

devices support two

methods of inclusion. When using a Z-Wave Plus

certiﬁed

controller choose Network Wide Inclusion.

Network Wide Inclusion:

Network Wide Inclusion allows your device to be included into

the network using devices already in the network to assist with

communication. Work your way from the closest devices to the

controller outward.

• Enter Programming Mode by holding the top of the paddle for

7 seconds, the Locator LED will blink amber.

• Tap the top of the paddle one time.

The Locator LED will quickly ﬂash green.

• The Decora Smart

Z-Wave

device is ready to learn into

the Z-Wave

network.

• Follow directions in the Z-Wave

controller to complete the

adding process.

• Upon successful addition to network the LED will turn off and

then blink green 3 times.

• If the adding process is not successful the LED will ﬂash red

3 times.

Traditional Inclusion:

For older controllers Traditional Inclusion is supported.

Depending on the age of the controller the controller will

need to be 3 to 35 feet from the device when including.

• Enter Programming Mode by holding the top of the paddle for

7 seconds, the Locator LED will blink amber.

• The Decora Smart

Z-Wave

device is ready to add to the

Z-Wave

network.

•

Follow directions in the Z-Wave

controller to enter learn mode.

• Tap the top of the paddle one time. The Locator LED will

quickly ﬂash green. The Z-Wave

controller will begin to pair

with the Decora Smart

device.

• Upon successful addition to the network the LED will turn off

and then blink green 3 times.

• If the adding process is not successful the LED will ﬂash red

3 times.

EXCLUSION FROM A Z-WAVE

NETWORK

When removing a device from a Z-Wave

network best

practice is to use the exclusion command found in the

Z-Wave

controller.

• Enter Programming Mode by holding the top of the paddle for

7 seconds, the Locator LED will blink amber.

• Follow directions in the Z-Wave

controller to enter exclusion

mode.

• Tap the top of the paddle one time. The Locator LED will

quickly ﬂash green. The Z-Wave

controller will exclude the

Decora Smart

device.

• The Z-Wave

controller will conﬁrm successful exclusion from

the network.

LOCATOR LED SETUP

Leviton Decora Smart

Z-Wave

devices have a locator

LED on the bottom of the paddle. The operation of the LED

can be changed.

Status Mode: LED On when the load is On:

The Locator LED is used to show the current state of the load:

• Enter Programming Mode by holding the top of the paddle for

7 seconds, the Locator LED will turn amber.

• Tap the top of the paddle 4 times.

The Locator LED will quickly ﬂash green and amber.

• Tap the top of the paddle once.

The Locator LED will ﬂash green 3 times to conﬁrm the

selection.

Locator Mode: LED On when the load is Off (Default):

The Locator LED is designed to easily ﬁnd the dimmer in a dark

room. If the setting has been changes and you wish to return to

the default operation.

• Enter Programming Mode by holding the top of the paddle for

7 seconds, the Locator LED will turn amber.

• Tap the top of the paddle 4 times.

The Locator LED will quickly ﬂash green and amber.

• Tap the top of the paddle twice.

The Locator LED will ﬂash amber 3 times to conﬁrm the

selection.

LED Off: Locator LED is always Off:

The Locator LED is turned off:

• Enter Programming Mode by holding the top of the paddle for

7 seconds, the Locator LED will blink amber.

• Tap the top of the paddle 4 times.

The Locator LED will quickly ﬂash green and amber.

• Tap the top of the paddle 3 times.

The Locator LED will ﬂash red 3 times to conﬁrm the

selection.

FACTORY DEFAULT

Devices are programmed to automatically time-out of any

settings after 20 seconds.

EXITING PROGRAMMING

When removing a device from a network it is best practice to use

the Exclusion process. In situations where a device needs to

be returned to factory default follow the following steps. A reset

should only be used when a controller is inoperable or missing.

• Hold the the top of the paddle for a total of 14 seconds.

• After the ﬁrst 7 seconds the LED turns amber.

• The Locator LED will quickly ﬂash red/amber after 14

seconds.

• Release the the top of the paddle and the device will reset.

Leviton Decora Smart

Z-Wave

Devices are conﬁgurable through

the paddle as well as over the Z-Wave

network. Compatible

Z-Wave

controllers can add support for additional advanced

options. Consult your Z-Wave

controller manufacturer for

compatibility with advanced feature support.

Locator LED Status

• Parameter No: 7, Length: 1 Byte

• Valid Values = 0 to 255 (default 255)

- 0 = LED Off

- 254 = Status Mode

- 255 = Locator Mode

ADVANCED OPTIONS

Z-WAVE

ASSOCIATIONS

• Group Number: 1

• Maximum Nodes: 5

• Z-Wave Plus

Lifeline: A NOTIFICATION frame is sent to the nodes

in this association group when a Lifeline event occurs.

• All nodes in the association group receive notiﬁcation of status

changes.

Z-WAVE PLUS INFO

ASSOCIATION

ASSOCIATION GRP INFO

VERSION

MANUFACTURER SPECIFIC

CONFIGURATION

DEVICE RESET LOCALLY

POWERLEVEL

COMMAND CLASS SWITCH BINARY

BASIC

SWITCH ALL

SCENE ACTUATOR CONF

SCENE ACTIVATION

FIRMWARE UPDATE MD V2

HAIL

ADDITIONAL SUPPORTED CLASSES

• Lights Flickering

- Lamp has a bad connection.

- Wires not secured ﬁrmly with wire connectors of switch or

terminal screws of remote.

• Light does not turn ON and Locator LED does not turn ON

- Circuit breaker or fuse has tripped.

- Lamp is burned out.

- Neutral not wired to switch (White wire).

- Conﬁrm that the device is being supplied from a 120V AC, 60

Hz source ONLY.

• Remote does not operate lights

- Ensure that total wire length does not exceed 300 ft.

- Ensure wiring is correct.

TROUBLESHOOTING

FOR CANADA ONLY

For warranty information and/or product returns, residents of Canada

should contact Leviton in writing at Leviton Manufacturing of Canada

Ltd to the attention of the Quality Assurance Department, 165

Hymus Blvd, Pointe-Claire (Quebec), Canada H9R 1E9 or by

telephone at 1-800-405-5320.

This device complies with Part 15 of the FCC Rules. Operation is subject to

following two conditions: (1) this device may not cause harmful interference,

and (2) this device must accept any interference received, including

interference that may cause undesired operation of the device.

This equipment has been tested and found to comply with the limits for a

Class B Digital Device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment OFF

and ON, the user is encouraged to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving Antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/tv technician for help.

FCC CAUTION

Any changes or modiﬁcations not expressly approved by Leviton

Manufacturing Co., Inc., could void the user's authority to operate the

equipment.

FCC COMPLIANCE STATEMENT

IC COMPLIANCE STATEMENT

This device complies with Industry Canada licence-exempt RSS

standard(s). Operation is subject to the following two conditions: (1)

this device may not cause interference, and (2) this device must accept

any interference, including interference that may cause undesired

operation of the device.

WEB VERSION

Summary of content (2 pages)

PAGE 1
decora smart™ • Position all wires to provide room in outlet wall box for device. • Ensure that the word "TOP" is facing up on device strap. • Partially screw in mounting screws in wall box mounting holes. NOTE: Dress wires with a bend as shown in diagram in order to relieve stress when mounting device. Switch with Z-Wave® Technology Cat. No.
PAGE 2
WARNINGS AND CAUTIONS WARNINGS AND CAUTIONS • • • • • • • • • • TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER at circuit breaker or fuse and test that power is off before wiring! To be installed and/or used in accordance with electrical codes and regulations. If you are unsure about any part of these instructions, consult an electrician. The Decora® DZ15S is not compatible with standard 3-way or 4-way switches.