Instructions / Assembly

Scene Capable Plug-In Appliance Module
Cat. No. DZPA1
Incandescent: 1800W - Fluorescent: 1800VA - LED/CFL: 5A
Resistive: 15A - Motor: 1/2HP
Rated: 120VAC, 60Hz
INSTALLATION INSTRUCTIONS
DI-000-DZPA1-02A
INTRODUCTION INSTALLING YOUR MODULE
Leviton’s Decora
®
Z-Wave
®
control
components are designed to communicate
with each other via Radio Frequency (RF) to
provide remote control of your lighting. In a
Z-Wave
®
network, each device is designed to
act as a router. These routers will re-transmit
the RF signal from one device to another until
the intended device is reached. This ensures
that the signal is received by its intended
device by routing the signal around obstacles
and radio dead spots.
WARNING:
TO AVOID FIRE, PERSONAL INJURY OR
DEATH DO NOT USE the remote for the
control of high power heating appliances such
as portable heaters. Remember to exercise
good common sense when using the Timer
features of your remote, especially when
scheduling unattended devices. There can
be some unexpected consequences if not
used with care. For example, an empty coffee
pot can be remotely turned on. If that should
happen, your coffee pot could be damaged
from overheating. If an electric heater is turned
on by remote control while clothing is draped
over it, a fire could result. DO NOT USE the
remote for the control of high power heating
appliances such as portable heaters. DO NOT
change location after unit is enrolled in Z-wave
®
network.
Attaching Scene Capable
Plug-In Appliance Module to
Wall Receptacle:
Step 2
• Plug the Scene Capable Plug-in Appliance
Module into wall receptacle. Verify that
receptacle is live. If controlled by a wall switch,
the switch must be kept ON at all times.
Attaching Load to Scene
Capable Plug-In Appliance
Module:
Step 1
NOTE: In order to use your Scene Capable
Plug-In Appliance Module in a Z-Wave
®
network,
it must be included in the network using a Primary
Programmer/Remote, such as Leviton’s Cat.
No. VRCPG. Before including your module,
please refer to the Primary Programmer/Remote
instruction sheet for complete information.
• Locate load to be controlled by Scene Capable
Plug-In Appliance Module and ensure it is
fully operational. Attach load plug into module
receptacle noting proper polarity of blades.
NOTE: Use check boxes when Steps are
completed.
• Scene capable
• Programming button
• Two way communication
• RF reliability
• Ease of installation – No new wiring
• Compatible with other Z-Wave
®
enabled
devices
FEATURES
Programming
Button
WARNINGS AND CAUTIONS:
• To be installed and/or used in accordance with appropriate electrical codes and regulations.
• If you are unsure about any part of these instructions, consult an electrician.
• For control of Electronic Ballast, CFL’s and LED drivers.
WARNINGS AND CAUTIONS:
• Unplug unit when servicing fixture or changing bulbs.
• Save this instruction sheet. It contains important technical data along with testing and
troubleshooting information which will be useful after installation is complete.
• Not for use with Vizia RF
®
lighting systems.
If your module is not responding, or you are
unable to control it after you have tried to
Include/Exclude it multiple times, it may be
necessary to reset the module to its original
factory settings. To accomplish this, proceed
as follows:
• Unplug the module and wait 5 seconds.
Plug the module back in and within 20
seconds press and hold the programming
button until the LED turns Amber and then
flashes Red. The module is now reset. Once
the module is reset, it will be necessary to
Re-Include it to a network before it can be
used.
CAUTION: SETTING A DEVICE TO A
FACTORY DEFAULT DOES NOT EXCLUDE
THAT DEVICE FROM A NETWORK. THE
EXCLUSION PROCEDURE MUST BE
FOLLOWED TO REMOVE THE DEVICE
FROM THE PRIMARY REMOTE’S
INFORMATION TABLE. FAILURE TO DO SO
MAY RESULT IN SYSTEM THAT IS SLOW TO
RESPOND, OR MAY FAIL TO RESPOND TO
SOME DEVICES.
IF YOU HAVE TO RESET
THE CONTROLLER WITHOUT EXCLUDING
IT GO TO THE REMOVE FAILED MENU OF
YOUR PROGRAMMER AND REMOVE THE
DEVICE.
NOTE: To include your module into a network,
contact Leviton’s Techline at 1-800-824-3005 or
visit Leviton’s website at www.leviton.com.
FACTORY DEFAULT
WEB VERSION