Instructions / Assembly

ManualsBrandsLeviton ManualsElectrical15 Amp 2-Pole White Flat Plug

ENGLISH

INSTALLATION INSTRUCTIONS

PK-93287-10-02-0D

LIMITED 2 YEAR WARRANTY AND EXCLUSIONS

Leviton warrants to the original consumer purchaser and not for the beneﬁt of anyone else that this product at the time of its sale by Leviton is free of defects in materials and workmanship under normal and proper use for two years from the

purchase date. Leviton’s only obligation is to correct such defects by repair or replacement, at its option. For details visit www.leviton.com or call 1-800-824-3005. This warranty excludes and there is disclaimed liability for labor for removal of

this product or reinstallation. This warranty is void if this product is installed improperly or in an improper environment, overloaded, misused, opened, abused, or altered in any manner, or is not used under normal operating conditions or not in

accordance with any labels or instructions. There are no other or implied warranties of any kind, including merchantability and ﬁtness for a particular purpose, but if any implied warranty is required by the applicable jurisdiction, the duration

of any such implied warranty, including merchantability and ﬁtness for a particular purpose, is limited to two years. Leviton is not liable for incidental, indirect, special, or consequential damages, including without limitation, damage to,

or loss of use of, any equipment, lost sales or proﬁts or delay or failure to perform this warranty obligation. The remedies provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise.

FOR CANADA ONLY

For warranty information and/or product returns, residents of Canada should contact Leviton in writing at Leviton Manufacturing of Canada Ltd to the attention of the Quality Assurance Department, 165 Hymus Blvd, Pointe-Claire

(Quebec), Canada H9R 1E9 or by telephone at 1 800 405-5320.

Straight Blade Plugs and Connectors

Cat. Nos. 48642, 48643

Rated: 15A - 125V

• For lamps and small appliances

Cat. Nos. 48646, 48648

Rated: 15A - 125V

• For power tools and large appliances

• Cord clamp relieves strain on wiring terminals

INSTALLATION

For Technical Assistance Call: 1-800-824-3005 (U.S.A. Only) www.leviton.com

CAT. NO. 48643

CAUTION: DO NOT cut or DAMAGE cord jacket or insulation except where indicated.

NOTE: Use with 2-wire ﬂexible cords 3/8" (.9 cm) maximum diameter, 18-2 to 14-2 AWG.

Pry body out of cover (Diagram B, Fig. 1).

Feed cord through cover (Diagram B, Fig. 2).

Remove cord jacket and conductor insulation (Diagram B, Fig. 3).

4. Connect conductors to terminal screws as follows (Diagram B, Fig. 4):

NOTE: Back out terminal screws until they stop turning (do not force past this point).

• Twist copper strands of each conductor tightly together.

• Loop conductor clockwise, 3/4 turn around terminal screw and tighten screw securely.

• Cut off any wire strands not secure under terminal screw.

Push body into cover until both tabs lock in slots (Diagram B, Fig. 5).

CAT. NO. 48648

CAUTION: DO NOT cut or DAMAGE cord jacket or insulation except where indicated.

NOTE: Use with 3-wire ﬂexible round cords 7/16" (1 cm) maximum diameter, 18-3 to 16-3 AWG.

Pry body out of cover (Diagram D, Fig. 1).

Feed cord through cover (Diagram D, Fig. 2).

Remove cord jacket and conductor insulation (Diagram D, Fig. 3).

4. Connect conductors to terminal screws as follows (Diagram D, Fig. 4):

NOTE: Back out terminal screws until they stop turning (do not force past this point).

• BLACK (Hot) wire to BRASS screw, WHITE (Neutral) wire to SILVER screw, and GREEN (Ground) wire to

GREEN screw.

• Twist copper strands of each conductor tightly together.

• Loop conductor clockwise, 3/4 turn around terminal screw and tighten screw securely.

• Cut off any wire strands not secure under terminal screw.

Push body into cover until both tabs lock in slots (Diagram D Fig. 5).

Alternately tighten clamp screws until cord is gripped securely (Diagram D, Fig. 5).

WARNINGS AND CAUTIONS

• TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE WIRING!

• To be installed and/or used in accordance with appropriate electrical codes and regulations.

• If you are unsure about any part of these instructions, consult an electrician.

• Use this device with copper or copper clad wire only.

• For indoor applications only.

CAT. NO. 48642

CAUTION: DO NOT cut or DAMAGE cord jacket or insulation except where indicated.

NOTE: Use with 2-wire ﬂexible cords 3/8" (.9 cm) maximum diameter, 18-2 to 14-2 AWG.

NOTE: Underwriter’s Knot recommended to reduce possible cord strain that could loosen terminal connections.

Pry body out of cover (Diagram A, Fig. 1).

Feed cord through cover (Diagram A, Fig. 2).

Remove cord jacket and separate conductors (Diagram A, Fig. 3).

Tie Underwriter’s Knot and pull tight (Diagram A, Fig. 4). Cut conductors to size indicated.

Remove insulation from end of each conductor to expose 1/2" (1.3 cm) copper strands (Diagram A, Fig. 5).

6. Connect conductors to terminal screws as follows (Diagram A, Fig. 5):

NOTE: Back out terminal screws until they stop turning (do not force past this point).

• Twist copper strands of each conductor tightly together.

• Loop conductor clockwise, 3/4 turn around terminal screw and tighten screw securely.

• Cut off any wire strands not secure under terminal screw.

Seat UL knot and push body into cover until both tabs lock in slots (Diagram A, Fig. 6).

CAT. NO. 48646

CAUTION: DO NOT cut or DAMAGE cord jacket or insulation except where indicated.

NOTE: Use with 2-wire ﬂexible round cords 7/16" (1 cm) maximum diameter, 18-2 to 14-2 AWG.

Pry body out of cover (Diagram C, Fig. 1).

Feed cord through cover (Diagram C, Fig. 2).

Remove cord jacket and conductor insulation (Diagram C, Fig. 3).

4. Connect conductors to terminal screws as follows (Diagram C, Fig. 4):

NOTE: Back out terminal screws until they stop turning (do not force past this point).

• Twist copper strands of each conductor tightly together.

• Loop conductor clockwise, 3/4 turn around terminal screw and tighten screw securely.

• Cut off any wire strands not secure under terminal screw.

Push body into cover until both tabs lock in slots (Diagram C, Fig. 5).

Alternately tighten clamp screws until cord is gripped securely (Diagram C, Fig. 5).

PK-93287-10-02-0D

DIAGRAM / SCHÉMA / DIAGRAMA A - Cat. 48642

Fig. 1 Fig. 2

Fig. 3 Fig. 4

Fig. 5 Fig. 6

Cover

Coquille

Cubierta

Body

Corps

Cuerpo

2-3/4"

2-3/4 po

7 cm

2-3/4"

2-3/4 po

7 cm

1/2"

1/2 po

1.3 cm

Cover

Coquille

Cubierta

Cord

Cordon

Cordón

Round cord

Cordon rond

Cordón redondo

Round cord

Cordon rond

Cordón redondo

End of jacket

Fin de la gaine

Final del forro del cordón

Separation point

Point de séparation

Punto de separación

Tab in slot

Patte dans la fente

Pestaña en la ranura

Flat cord (no jacket)

Cordon plat (sans gaine)

Cordón plano (sin forro)

Flat cord

Cordon plat

Cordón plano

1 po

2.5 cm

1 po

2.5 cm

DIAGRAM / SCHÉMA / DIAGRAMA B - Cat. 48643

Fig. 1 Fig. 2

Fig. 4 Fig. 5

Fig. 3

Cover

Coquille

Cubierta

Body

Corps

Cuerpo

Cover

Coquille

Cubierta

Cord

Cordon

Cordón

1/2"

1/2 po

1.3 cm

1/2"

1/2 po

1.3 cm

1-1/4"

1-1/4 po

3 cm

1-1/4"

1-1/4 po

3 cm

Round cord

Cordon rond

Cordón redondo

Flat cord (no jacket)

Cordon plat (sans gaine)

Cordón plano (sin forro)

Insulation

Isolant

Aislante

Copper strands

Brins de cuivre

Hilos de cobre

Insulation

Isolant

Aislante

Copper strands

Brins de cuivre

Hilos de cobre

Cover

Coquille

Cubierta

Body

Corps

Cuerpo

Tab in slot

Patte dans la fente

Pestaña en la ranura

DIAGRAM / SCHÉMA / DIAGRAMA C - Cat. 48646

Fig. 1 Fig. 2

Fig. 4 Fig. 5

Fig. 3

Insulation

Isolant

Aislante

Copper strands

Brins de cuivre

Hilos de cobre

1-1/2"

1-1/2 po

3.8 cm

3/4"

3/4 po

2 cm

Cover

Coquille

Cubierta

Body

Corps

Cuerpo

Cord clamp screw

Vis de collier

Tornillos de la

abrazadera

del cordón

Tab in slot

Patte dans la fente

Pestaña en la ranura

Cover

Coquille

Cubierta

Cord

Cordon

Cordón

DIAGRAM / SCHÉMA / DIAGRAMA D - Cat. 48648

Fig. 1 Fig. 2

Fig. 4 Fig. 5

Fig. 3

Insulation

Isolant

Aislante

Copper strands

Brins de cuivre

Hilos de cobre

Cover

Coquille

Cubierta

Body

Corps

Cuerpo

Cord clamp screw

Vis de collier

Tornillos de la

abrazadera

del cordón

Tab in slot

Patte dans la fente

Pestaña en la ranura

Cover

Coquille

Cubierta

Cord

Cordon

Cordón

1-1/2"

1-1/2 po

3.8 cm

3/4"

3/4 po

2 cm

White wire to

silver screw

Fil blanc à la

vis argent

Conductor blanco al

tornillo plateado

Green wire to

green screw

Fil vert à la vis verte

Black wire to brass

screw

Fil noir à la vis laiton

Conductor negro al

tornillo de latón

Conductor verde al tornillo verde