Installation Guide

ManualsBrandsLeviton ManualsElectrical20 Amp 125-Volt Duplex Self-Test Tamper Resistant/Weather Resistant GFCI Outlet, White

WHITE WIRE

FIL BLANC

HOT WIRE

FIL ACTIF

CHARGE

LOAD

LIGNE

LINE

White

Black (LINE)

Black

LINE

LOAD

This white wire is HOT only when

used to feed power to a switch.

Connect the LINE cable wires to the LINE terminals:

• The white wire connects to the WHITE terminal (Silver).

• The black wire connects to the HOT terminal (Brass).

Connect the switch leads to the switch controlled LOAD

(not GFCI protected, shown in diagram):

• One black switch lead connects to the LINE side black wire.

• The other black lead connects to the HOT side of the LOAD.

• The LOAD must be properly connected to NEUTRAL and grounded.

NOTE: Wiring for switched LOAD shown here is only one of several

options. If you are unsure about any part of these instructions, consult

a qualiﬁed electrician.

Connect the grounding wire (only if there is a grounding wire):

• For a box with no grounding terminal (diagram not shown): Connect the

LINE cable's bare copper

(or GREEN) wire directly to the grounding terminal on the GFCI receptacle.

• For a box with a grounding terminal (diagram shown above): Connect

a 6-inch bare copper (or GREEN) 12 or 14 AWG wire to the grounding

terminal on the GFCI. Also connect a similar wire to the grounding terminal

on the box. Connect the ends of these wires to the LINE cable's bare copper

(or GREEN) wire using a wire connector. If these wires are already in place,

check the connections.

Complete the installation:

• Fold the wires into the box, keeping the grounding wire away from the

WHITE and HOT terminals. Screw the receptacle to the box and attach the

faceplate.

• Go to step 8.

For Side wire -

Loop clockwise 3/4 of

the way around screw

For Back wire -

Insert bare wire fully

and tighten terminal

clamp on conductor

ONLY

For Side wire -

Loop clockwise

3/4 of the way

around screw

For Back wire -

Insert bare wire fully

and tighten terminal

clamp on conductor

ONLY

7. Connect the wires (choose A or B)... only after reading other side completely

A: Two Cable (4 or 6 wires) entering the box B: Three cables (6 or 9 wires) entering the box

8. Test your work

Why perform this test?

• If you miswired the GFCI it may not prevent personal injury or death due to a ground fault

(electrical shock).

• If you mistakenly connect the LINE wires to the LOAD terminals, the GFCI will not reset and will not

provide power to either the GFCI receptacle face or any receptacles fed from the GFCI.

Procedure:

(a) This GFCI is shipped from the factory in the tripped condition and cannot be reset until it is wired

correctly and power is supplied to the device. Plug a lamp or radio into the GFCI (and leave it plugged

in). Turn the power ON at the service panel. Ensure that the GFCI is still in the tripped condition

by pressing the TEST button. If the lamp or radio is OFF, and the GFCI will not reset, go to the

Troubleshooting section as the Line and Load connections are reversed.

(b) Press the RESET button fully and release. If the Status Indicator Light turns Green and the lamp or

radio is ON, the GFCI has been installed correctly. If the Status Indicator Light turns or continuously

blinks Red, or the GFCI cannot be reset, go to the Self-Test Operation section.

one(s), in addition to the GFCI, lose power when you press the GFCI TEST button. Place a "GFCI

PROTECTED OUTLET" sticker on every receptacle that lost power, then press the RESET button to

reset the GFCI. DO NOT plug life saving devices into any of the receptacles that lost power.

(d) Press the TEST button (then RESET button) every month to assure proper operation. If the Status

Indicator Light does not turn Green when the RESET button is depressed and then released, or the

GFCI cannot be reset, it must be replaced.

Back Wire:

PK-A3097-10-00-2A AR1675

WHITE WIRE

FIL BLANC

HOT WIRE

FIL ACTIF

CHARGE

LOAD

LIGNE

LINE

About Wire

Connections:

Side Wire:

About Wire Connections:

Side Wire:

Connect the LINE cable wires to the LINE terminals:

• The white wire connects to the WHITE terminal (Silver).

• The black wire connects to the HOT terminal (Brass).

Connect the LOAD (Receptacle) cable wires to the GFCI LOAD terminals:

• Remove the YELLOW sticker to reveal the LOAD terminals.

• The white wire connects to the WHITE terminal (Silver).

• The black wire connects to the HOT terminal (Brass).

Connect the switch leads to the switch controlled LOAD (not GFCI protected, shown

in diagram):

• One black switch lead connects to the line side black wire.

• The other black lead connects to the hot side of the load.

• The LOAD must be properly connected to NEUTRAL and grounded.

NOTE: Wiring for switched LOAD shown here is only one of several options. If you

are unsure about any part of these instructions, consult a qualiﬁed electrician.

Connect the grounding wires (only if there is a grounding wire):

• Connect a 6-inch bare copper (or GREEN) 12 or 14 AWG wire to the grounding terminal

on the GFCI. If the box has a grounding terminal, also connect a similar wire to the

grounding terminal on the box. Connect the ends of these wires to the LINE or LOAD

cable's bare copper (or GREEN) wire using a

wire connector. If these wires are already in place, check the connections.

Complete the installation:

• Fold the wires into the box, keeping the grounding wire away from the WHITE and HOT

terminals.

Screw the receptacle to the box and attach the faceplate.

• Go to step 8.

Wire

3/4" (1.9 cm)

Wire

3/4" (1.9 cm)

Wire

5/8" (1.6 cm)

Wire

5/8" (1.6 cm)

Grounding connection

to box (if box has a

grounding terminal)

Wire Connector

LINE cable

brings power

to the GFCI

Electrical

Box

Yellow

sticker

remains

in place

to cover

the LOAD

terminals

Cable to switched

LOAD

WHITE WIRE

FIL BLANC

HOT WIRE

FIL ACTIF

CHARGE

LOAD

LIGNE

LINE

White

Black (LINE)

Black

LINE

LOAD

Cable to

switched

LOAD

LINE

cable

brings

power to

the GFCI

Electrical

Box

Wire

Connector

Grounding connection

to box (if box has a

grounding terminal)

LOAD cable feeds

power to other

receptacle(s)

This white wire is HOT only when

used to feed power to a switch.

WHITE WIRE

FIL BLANC

HOT WIRE

FIL ACTIF

CHARGE

LOAD

LIGNE

LINE

This product is covered by the following U.S. Patent Nos.: 6,040,967; 6,246,558; 6,282,070; 6,381,112; 6,437,953; 6,646,838; 6,657,834; 6,788,173; 6,864,766; 6,944,001;

7,336,458; 7,355,117; 7,400,479; 7,463,124; 7,697,252; 7,737,809; 7,764,151; 7,820,909; 7,907,371; 8,004,804; 8,054,595; 8,130,480; 8,242,362; 8,547,126; 8,587,914;

8,599,522; 8,944,859 and corresponding foreign patents.

FOR CANADA ONLY

For warranty information and/or product returns, residents of Canada should contact Leviton in writing at Leviton Manufacturing of Canada Ltd to the attention of the Quality

Assurance Department, 165 Hymus Blvd, Pointe-Claire (Quebec), Canada H9R 1E9 or by telephone at 1 800 405-5320.

SmartlockPro is a Trademark of Leviton Manufacturing Co., Inc. registered in the United States, Canada, Mexico and China.

SELF-TEST OPERATION

• A Self-Test GFCI receptacle has all the features of a conventional GFCI receptacle.

In addition, this receptacle tests itself periodically to conﬁrm the GFCI electronics are

functional. The Status Indicator Light will be solid green when the GFCI is powered from

Line side and working correctly.

• Self-Test Indications: If the Status Indicator Light is solid or ﬂashing RED a problem

may exist. Press the TEST button to trip the GFCI. If unable to Reset, replace the GFCI.

NOTE: The status indicator may ﬂash Red at power "ON" and Reset.

Self Test

Cat. No.

Description

GFSW1 Tamper-Resistant SmartlockPro Slim GFCI with a switch

- 15A-125V AC, 60 Hz (20A feed-through only)

Switch 15A max. - 120V AC, 60 Hz

1/2 Hp. @ 120V, for motor loads of

12 FLA max., and not to exceed 1/2 Hp.

For Technical Assistance Call: 1-800-824-3005 (U.S.A. Only) 1 800 405-5320 (Canada Only) www.leviton.com

LIMITED 2 YEAR WARRANTY AND EXCLUSIONS

Leviton warrants to the original consumer purchaser and not for the beneﬁt of anyone else that this product at the time of its sale by Leviton is free of defects in materials and workmanship

under normal and proper use for two years from the purchase date. Leviton’s only obligation is to correct such defects by repair or replacement, at its option. For details visit www.leviton.

com or call 1-800-824-3005. This warranty excludes and there is disclaimed liability for labor for removal of this product or reinstallation. This warranty is void if this product is installed

improperly or in an improper environment, overloaded, misused, opened, abused, or altered in any manner, or is not used under normal operating conditions or not in accordance with

any labels or instructions. There are no other or implied warranties of any kind, including merchantability and ﬁtness for a particular purpose, but if any implied warranty

is required by the applicable jurisdiction, the duration of any such implied warranty, including merchantability and ﬁtness for a particular purpose, is limited to two years. Leviton is

not liable for incidental, indirect, special, or consequential damages, including without limitation, damage to, or loss of use of, any equipment, lost sales or proﬁts or

delay or failure to perform this warranty obligation. The remedies provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise.

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Increase the separation between the equipment and receiver. • Consult the dealer or an experienced radio/TV technician for help.

IC STATEMENT

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2)

this device must accept any interference, including interference that may cause undesired operation of the device.

TROUBLESHOOTING

Turn the power OFF and check the wire connections against the appropriate wiring diagram in step 7A or 7B. Make sure that there are no

loose wires or loose connections. If the Status Indicator Light is not ON and the device is unable to reset this could be a result of no power

available. Start the test from the beginning of step 8 if you rewired any connections to the GFCI.

RESET

TEST

RESET

TEST

RESET

TEST

RESET