Instructions / Assembly

ManualsBrandsLeviton ManualsDimmersIllumaTech Universal 150-Watt LED and CFL/600-Watt Incandescent Dimmer, White (5-Pack)

WARNINGS AND CAUTIONS:

• Useonlyone(1)dimmerina3-or4-waycircuit.Theswitch(es)willturnthelightonatthe

brightnesslevelselectedatthedimmer.

• UsewithcompatibledimmableLED,CFLbulbs,incandescentor120Vhalogenxturesonly.

ForacompletelistofcompatibleLEDandCFLbulbsrefertowww.leviton.com.

• WhenmultiplebulbsareusedwithonedimmerDO NOTmixbulbtypes.AllbulbsshallbeeitherLED;CFLor

incandescent.Usingthesamemake/modelofeachbulbwillenhancedimmerperformance.

Black

Red

Neutral

Green

Ground

Red

This wire is used in 3-way installations only.

For single pole installations, do not remove

this insulating label.

LED/Compact Fluorescent/Incandescent Slide Dimmer

SinglePole(Onelocation)or3-Way(Multi-location)

Cat.No.IPL06–LED/CFL150W,Incandescent600W

120VAC,60Hz

INSTALLATION INSTRUCTIONS

Bend back and forth to remove side section

Tools needed to install your Dimmer

Slotted/PhilipsScrewdriver ElectricalTape

Pliers Pencil

Cutters Ruler

Push in side at tab

to release

Line up tabs on back of

slider to switch shaft and

press in side to attach

Movethesliderupordownonefullcycletoautomaticallyengagethe

slidercontrolmechanism.

Step 3

Changing the color of your Dimmer

Ifacolorchangekitisprovidedwithyourdevice,proceedwiththe

followingstepifyouneedtochangethecolor.Otherwise,proceedwith

the"Installing Dimmer by itself or with other devices"section.

Inincandescentmulti-dimmerinstallations,thereductionofthedimmer’s

capacityisrequired.Refertothechartformaximumloadperdimmer.

NoderatingisrequiredforuseinDimmableCFLordimmableLED

multi-dimmerinstallations.

MULTI-DEVICE APPLICATION

NOTE: Youonlyneedtoremovesidesectionsifinstallingwithother

dimmersorifitdoesnottinwallbox–notwheninstallingwith

mechanicalswitches.

Installing Dimmer by itself or with other devices

Wheninstallingmorethanonedimmerinthesamelocation,theside

sectionsofthemountingstrapmustberemoved.Useplierstocarefully

bendsidesectionsbackandforthuntiltheybreakoff.Thesidesections

dissipateheat,soremovingthemrequiresaderatingofthedimmer's

capacity(refer to chart).

Step 2

MAXIMUM LOAD PER DIMMER FOR MULTI-DEVICE

Cat. No.

IPL

Single

600W

Two Devices

500W

More than 2 Devices

400W

ONOFF

ONOFFONOFF

ONOFF

WARNING:Toavoidre,shock,ordeath;TURN OFF

POWERatcircuitbreakerorfuseandtestthatpowerisoff

beforewiring!

Step 1

Identifying your wiring application

(most common):

NOTE:Ifthewiringinthewallboxdoesnotresembleanyof

thesecongurations,consultanelectrician.

Single Pole

1. Line(Hot)

2. Neutral

3. Ground

4. Load

IMPORTANT:For3-Wayapplications,notethatoneofthescrewterminals

fromtheoldswitchbeingremovedwillusuallybeadifferentcolor(Black)

orlabeledCommon.Tagthatwirewithelectricaltapeandidentifyasthe

common(LineorLoad)inboththedimmerwallboxand3-waywallbox.

Preparing and connecting wires:

Strip gage

Cut

(if necessary)

5/8"

• Makesurethattheendsofthewiresfromthewallboxarestraight

(cut if necessary).

• Remove5/8"(1.6cm)ofinsulationfromeachwireinthewallbox

(shown).

• For Single-Pole Application, go to Step 4a.

• For 3-Way Application, go to Step 4b.

Single-Pole Wiring Application:

Insertwires

straightthentwist

clockwise

Electrical

Tape

Step 4a

3-Way

1. LineorLoad

(See note below)

2. Neutral

3. Ground

4. FirstTraveler–notecolor

5. SecondTraveler–notecolor

Remove

all inner

side

sections

Do not

remove

outer

side

sections

DI-000-IPL06-02A-X3

Installing your Dimmer

NOTE: UsecheckboxeswhenStepsarecompleted.

√

Hot (Black)

Neutral (White)

Load

Dimmer

Black

Green

Ground

Black

White

Red

Line

120VAC, 60Hz

Red

Cap with

Wire Connector

WARNINGS AND CAUTIONS:

• TO AVOID FIRE, SHOCK, OR DEATH;TURN OFF POWERatcircuitbreakerorfuseandtestthatpowerisoff

beforewiringorservicingxture!

• Tobeinstalledand/orusedinaccordancewithappropriateelectricalcodesandregulations.

• Ifyouareunsureaboutanypartoftheseinstructions,consultanelectrician.

• Toavoidoverheatingandpossibledamagetothisdeviceandotherequipment,DO NOTinstalltocontrola

receptacle,amotor-oratransformer-operatedappliance,oranyotherlightingsourcesthanthosespecied.

• Usethisdevicewith copper or copper clad wire only.

Summary of content (2 pages)

PAGE 1
LED/Compact Fluorescent/Incandescent Slide Dimmer Single Pole (One location) or 3-Way (Multi-location) Cat. No. IPL06 – LED/CFL 150W, Incandescent 600W 120VAC, 60Hz INSTALLATION INSTRUCTIONS WARNINGS AND CAUTIONS: WARNINGS AND CAUTIONS: • T O AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER at circuit breaker or fuse and test that power is off before wiring or servicing fixture! • To be installed and/or used in accordance with appropriate electrical codes and regulations.
PAGE 2
Step 4a cont'd OPERATION CFL Connect wires per WIRING DIAGRAM as follows: Screw wire nuts on clockwise making sure no bare conductors show below the wire connectors. Secure each connector with electrical tape. • Green dimmer Ground lead to Green or bare copper wire in wall box. • Black dimmer lead to any wall box wire removed from old switch. • Red dimmer lead without insulating label to remaining wall box wire. • Remaining Red dimmer lead should have Red insulation label affixed.