Installation Guide

ManualsBrandsLeviton ManualsSmart Home15 Amp Decora Smart with HomeKit Technology Switch, Works with Siri (2-Pack)

WARNINGS AND CAUTIONS

• TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER at circuit breaker or fuse and test that power is off before wiring!

• To be installed and/or used in accordance with electrical codes and regulations.

• If you are unsure about any part of these instructions, consult an electrician.

• The Decora

Smart

DH15S is not compatible with standard 3-way or 4-way switches.

• Use only (1)

Decora

Smart

DH15S switch in a multi-location circuit with up to 9 coordinating remote switches (DD0SR-01Z), or up to 4 matching remote switches (DD0SR-DLZ).

• Maximum wire length from switch to all installed remotes cannot exceed 300 ft (90m).

3-Way Wiring with DD0SR-01Z Coordinating

Remote (no LED) Application:

WARNING: TO AVOID FIRE SHOCK OR DEATH;

TURN OFF POWER at circuit breaker or fuse and test

that power is off before wiring!

Identifying your wiring application

(most common):

NOTE: If the wiring in your wall box does not

resemble any of these conﬁgurations, consult

an electrician.

INSTALLING YOUR SWITCH

NOTE: Use check boxes when Steps are completed.

/./&&

/./&&/./&&

/./&&

Step 1

Single Pole

1. Line (Hot)

2. Neutral

3. Ground

4. Load

3-Way

1. Line or Load

(see important instruction)

2. Neutral

3. Ground

4. First Traveler – note color

5. Second Traveler – note color

Step 2

Terminal

Screw marked

Black (BK)

Terminal

Screw marked

Red (RD)

Terminal Label:

Use terminal for 3-way or more applications only.

For single-pole applications, DO NOT remove label.

Terminal

Screw marked

White (WH)

Terminal

Screw marked

Yellow/Red

(YL/RD)

YL/RD

Single Pole Wiring Application:

Step 4a

WIRING SWITCH:

Connect wires per WIRING DIAGRAM as follows:

• Green or bare copper wire in wall box to Green terminal

screw.

• Line Hot wall box wire to terminal screw marked "BK".

• Load wall box wire to terminal screw marked "RD".

• Line Neutral wall box wire to terminal screw marked "WH".

•

Switch terminal screw marked "YL/RD" should have Red

insulation label afﬁxed.

NOTE: If insulating label is not afﬁxed to terminal screw

marked "YL/RD", use electrical tape to cover.

• Proceed to Step 5.

FEATURES

INTRODUCTION

SwitchCoordinating Remote (no LED)

Terminal

Screw

marked

Black (BK)

Terminal

Screw marked

Red (RD)

Terminal

Screw marked

White (WH)

Terminal

Screw

marked

Yellow/Red

(YL/RD)

Terminal

Screw marked

Yellow/Red (YL/RD)

YL/RD

Neutral to Terminal

Screw marked

White (WH)

3 3

5 5

Terminal

Screw

marked

Black

(BK)

Terminal

Screw

marked

Yellow/Red

(YL/RD)

Green

Ground

Green

Ground

Hot (Black)

Neutral (White)

Coordinating Remote (no LED)

YL/RD

Black

White

Line

120/277VAC

60Hz

(unused)

Load

Switch

Step 4b

NOTE: The switch must be installed in a wall box that has a Line Hot and

Neutral connection. The coordinating remote must be installed in a wall

box with a Load connection and a Neutral connection. A Neutral wire to

the coordinating remote needs to be added as shown. If you are unsure

about any part of these instructions, consult an electrician.

NOTE: Maximum wire length from switch to all installed remotes cannot

exceed 300 ft (90 m).

WIRING SWITCH (wall box with line hot connection):

Connect wires per WIRING DIAGRAM as follows:

• Green or bare copper wire in wall box to Green terminal screw.

• Line Hot (common) wall box wire identiﬁed (tagged) when removing

old switch to terminal screw marked "BK".

• First Traveler wall box wire to terminal screw marked "RD"

(note wire color).

• Remove Red insulating label from terminal screw marked "YL/RD".

• Second Traveler wall box wire to terminal screw marked "YL/RD"

(note wire color). This traveler from the switch must go to the

terminal screw on the remote marked "YL/RD".

• Line Neutral wall box wire to terminal screw marked "WH".

WIRING COORDINATING REMOTE

(wall box with load connection):

Connect wires per WIRING DIAGRAM as follows:

NOTE: "BK" and "RD" terminals on coordinating remote are unused.

Tighten both screws.

• Green or bare copper wire in wall box to Green terminal screw.

• Load wall box wire identiﬁed (tagged) when removing old switch to

First Traveler (note color as above).

• Second Traveler wall box wire (note color as above) to terminal screw

marked "YL/RD". This traveler from the remote must go to the terminal

screw on the switch marked "YL/RD".

• Remove White insulating label from terminal screw marked "WH".

• Line Neutral wall box wire to terminal screw marked "WH".

• Proceed to Step 5.

TOOLS NEEDED TO INSTALL YOUR SWITCH

Slotted/Phillips Screwdriver Electrical Tape Pliers

Pencil Cutters Ruler

Changing the color of your Switch:

Your switch comes with two color options. The switch ships with the

White frame attached. To change color of frame, proceed as follows:

Insert top

tabs and

press in

bottom

tabs to

attach

Push in

sides at

bottom tabs

and pull

outward to

release

Preparing and connecting wires:

This switch can be wired using side wire terminal screws

or through backwire openings. Choose appropriate wire

stripping speciﬁcations accordingly.

IMPORTANT : For 3-Way applications, note that one of the screw

terminals from the old switch being removed will usually be a

different color (Black) or labeled Common. Tag that wire with

electrical tape and identify as the common (Line or Load) in both the

switch wall box and remote wall box.

Step 3

• Make sure that the ends of the wires from the wall box are

straight (cut if necessary).

• Remove insulation from each wire in the wall box as shown.

• For Single-Pole Application, go to Step 4a.

• For 3-Way Coordinating Remote (no LED) Application, go to Step 4b.

• For 3-Way Matching Remote (with LED) Application, go to Step 4c.

5/8"

(1.6 cm)

Strip Gage

(measure bare

wire here)

Cut

(if necessary)

Side Wire Connection

Side wire terminals accept

#14-12 AWG solid copper

wire only.

Back Wire Connection

Back wire openings accept

#14-12 AWG solid copper

wire only.

Hot (Black)

Neutral (White)

Load

Switch

Black

White

Green

Ground

YL/RD

Line

120/277VAC,

60Hz

Use terminal for

3-way or more

applications only.

For single-pole

applications,

DO NOT remove label.

3-Way Wiring with DD0SR-DLZ Matching

Remote (with LED) Application:

Step 4c

SwitchMatching Remote (with LED)

Terminal

Screw

marked

Black

(BK)

Terminal

Screw marked

Red (RD)

Terminal

Screw marked

White (WH)

Terminal

Screw

marked

Yellow/

Red

(YL/RD)

Terminal

Screw marked

Red (RD)

Neutral to Terminal

Screw marked

White (WH)

YL/RD

Terminal

Screw

marked

Black

(BK)

Terminal

Screw

marked

Yellow/

Red

(YL/RD)

Hot (Black)

Neutral (White)

Load

YL/RD

YL/RDRD

Black

White

Line

120/277 VAC

60Hz

WH BK

Matching Remote (with LED)

Switch

Green

Ground

Green

Ground

(unused)

NOTE: The switch must be installed in a wall box that has a Load and

Neutral connection. The matching remote must be installed in a wall

box with a Line Hot connection and a Neutral connection. A Neutral

wire to the matching remote needs to be connected as shown. If you

are unsure about any part of these instructions, consult an electrician.

NOTE: Maximum wire length from switch to all installed remotes

cannot exceed 300 ft (90 m).

WIRING MATCHING REMOTE

(wall box with line hot connection):

Connect wires per WIRING DIAGRAM as follows:

NOTE: "RD" terminal on matching remote is unused. Tighten screw.

• Green or bare copper wire in wall box to Green terminal screw.

• Line Hot (common) wall box wire identiﬁed (tagged) when removing

old switch and First Traveler to Remote terminal marked BK.

• Second Traveler wall box wire from switch to remote terminal screw

marked "YL/RD" (note wire color). This traveler from the remote

must go to Yellow/Red switch terminal screw.

• Line Neutral wall box to remote terminal screw marked "WH".

WIRING SWITCH (wall box with load connection):

Connect wires per WIRING DIAGRAM as follows:

• Green or bare copper wire in wall box to Green terminal screw.

• Load wall box wire identiﬁed (tagged) when removing old switch to

Red terminal screw.

• First Traveler Line Hot to Black terminal screw.

• Remove Red insulating label from Yellow/Red terminal screw.

• Second Traveler wall box wire (note color as above) to Yellow/Red

terminal screw. This traveler from the switch must go to the terminal

screw on the remote marked "YL/RD".

• Line neutral wall box wire to White terminal screw.

• Proceed to Step 5.

RATINGS

Incandescent - 1800W - 120VAC, 60Hz

LED/CFL - 5A, 600W - 120VAC, 60Hz

Fluorescent - 15A - 120VAC, 60Hz

8A - 277VAC, 60Hz

Resistive - 15A - 120VAC, 60Hz

Motor - 1/2 HP - 120VAC, 60Hz

WARNINGS AND CAUTIONS

•

TO AVOID FIRE, PERSONAL INJURY OR PROPERTY DAMAGE, DO NOT install to control a receptacle.

• Recommended minimum wall box depth is 2-3/4".

• Use this switch with copper or copper clad wire only.

• Save this instruction sheet. It contains important technical data along with testing and troubleshooting information which will be useful after installation is complete.

• Leviton HomeKit-enabled accessories rely on Wi-Fi

communication. Increasing the number of Wi-Fi

accessories can affect Wi-Fi

performance. Consult the network’s wireless

access point speciﬁcations to determine the maximum number of supported Wi-Fi

accessories. For installations with a large number of Leviton HomeKit

Wi-Fi

accessories, a high

performance wireless access point capable of supporting a large number of accessories may be required.

Leviton’s Decora Smart

accessories are designed to streamline home

control with other HomeKit-enabled accessories. Apple HomeKit

technology provides an easy, secure way to control HomeKit-enabled

accessories using Siri voice control on your iPhone or iPad. After

installing your Decora Smart

Switch, conﬁgure it from the Leviton

Decora

Smart

Home app with just a few simple steps.

WARNING: TO AVOID FIRE, PERSONAL INJURY OR DEATH

DO NOT USE the remote for the control of high power heating

appliances such as portable heaters. There can be some unexpected

consequences if not used with care. For example, an empty coffee pot

can be remotely turned on. If that should happen, your coffee pot could

be damaged from overheating. If an electric heater is turned on by

remote control while clothing is draped over it, a ﬁre could result. This

switch will not control lighting that is used with electronic low-voltage

and high frequency power supply transformers, nor high pressure

discharge lamps (HID lighting). This includes mercury-vapor, sodium

vapor and metal halide lamps.

Decora Smart

accessories are ideal for living rooms, bedrooms,

kitchens, dining rooms, home ofﬁces, outdoor lighting or anywhere full

control of lighting is desired.

• The Decora Smart

Switch is HomeKit-enabled using Wi-Fi

technology for residential applications

• Compatible with the Leviton Decora Smart Home app as well as

other HomeKit-enabled apps

•

Over The Air (OTA) ﬁrmware updates via the Leviton

Decora Smart

Home app

• Single pole or three way compatible

• Ease of installation - No new wiring

DI-000-DH15S-02A

REQUIRED

• Wi-Fi

Network

• Free Leviton Decora Smart Home app

• Controlling this HomeKit-enabled accessory away from home

requires an Apple TV (3rd generation or later) with Apple TV

software 7.0 or later and an iPhone or iPad with iOS 8.1 or later

WEB VERSION