Instructions / Assembly

Restore Power:
Restore power at circuit breaker or fuse.
Installation is complete.
Step 8
For Technical Assistance Call: 1-800-824-3005 (U.S.A. Only) www.leviton.com
• Lights flickering
- Lamp has bad connection.
- Wires not secured firmly with wire connectors.
• CFL and LED flickers at low end of dimming range
- Increase the low end of the dimming range.
Programming Section - setting minimum light level
• CFL or LED bulb flickers throughout dimming range
- Ensure the bulbs are marked dimmable.
- Please refer to recommended dimmable LED and CFL bulbs at
www.leviton.com/universal.
• Light does not turn ON
- Circuit breaker or fuse has tripped.
- Lamp is burned out.
- Lamp Neutral connection is not wired.
NOTE: If further information is needed in identifying the HOT wire in a
3-Way application, go to Leviton's website at www.leviton.com.
Step 4a cont'd
• Green or bare copper wall box wire to terminal screw marked "GR".
• Line Hot wall box wire to terminal screw marked "BK".
• Load wall box wire to terminal screw marked "RD".
• Remaining Dimmer terminal screw marked "RD" should have an insulation
label affixed. DO NOT REMOVE this label in a single pole application.
Proceed to Step 5.
3-Way Wiring Application:
Step 4b
Dimmer Mounting:
TURN OFF POWER AT CIRCUIT BREAKER OR FUSE.
Step 7
Installation may now be completed
by carefully positioning all wires to
provide room in wall box for dimmer.
Mount dimmer into box with mounting
screws supplied.
Attach wallplate.
ON/OFF:
Press top of Decora
®
rocker
- Lights will turn ON.
Press bottom of Decora
®
rocker
- Lights will turn OFF.
BRIGHTEN & DIM:
Move slide bar
- Lights will BRIGHTEN or DIM.
• Restore power at circuit breaker or
fuse.
• Carefully holding dimmer, move
slider control lever to highest position
and press the top of the Decora
®
rocker. Lights should turn ON to
brightest level.
If lights does not turn ON, refer to
the TROUBLESHOOTING section.
Testing your Dimmer prior to mounting in the
wall box:
Step 6
Step 5
Dimmer Bulb Selector Switch:
Cat. No. DSL06 is pre-set at the factory with the bulb selector
switch set to Mode A (LED/Incandescent). For CFL bulb
applications the switch should be moved to Mode B (CFL). The
lamp selector slide switch also allows the user to adjust the
minimum light level when dimming. Information on this feature is
found under PROGRAMMING.
NOTE: See illustration for location of bulb selector switch.
Setting Minimum Light Level
1. Press bottom of Decora
®
rocker to turn the dimmer OFF and move the slide
bar to the bottom.
2. Remove color kit (see Changing the color of your Dimmer section on page 1).
3. Set the bulb selector switch to the LED/Incandescent position (Mode A).
4. Press on/off actuator to turn the load ON.
5. Set the bulb selector switch to the CFL
position (Mode B).
6. Raise or lower the slide control level to
achieve the desired minimum light level.
7. Set the bulb selector switch back to LED/
Incandescent position (Mode A).
8. A momentary flash of the bulb will occur
confirming the new setting.
9. Press on/off actuator to turn the load OFF.
10. Replace color kit (see Changing the color
of your Dimmer section on page 1).
NOTE: For dimmable CFL lamps you must
return the bulb selector to the CFL position
(Mode B).
LED/Incandescent (Mode A): The selector switch is pre-set at the factory to this
mode. Use this mode for dimmable LED bulbs and incandescent/halogen bulbs. To
avoid flickering at the low end of the dimming range you can pre-set the minimum
light level. See PROGRAMMING to manually program the minimum light level.
CFL (Mode B): To be used for dimmable CFL bulbs only. In this mode the dimmer
provides a pre-set kick-start to aid the lamp in starting. To avoid flickering at the low
end of the dimming range you can pre-set the minimum light level.
See PROGRAMMING to manually program the minimum light level.
Locator Light Switch (LOC): The LED Locator Light will illuminate when the load
is OFF. To disable the Locator Light move the Locator Light Switch to the OFF
position.
DI-000-DSL06-02A
LIMITED 5 YEAR WARRANTY AND EXCLUSIONS
Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that this product at the time of its sale by Leviton is free of defects in materials and workmanship under normal and proper use for five years from the purchase date. Leviton’s only obligation is to correct
such defects by repair or replacement, at its option. For details visit www.leviton.com or call 1-800-824-3005. This warranty excludes and there is disclaimed liability for labor for removal of this product or reinstallation. This warranty is void if this product is installed improperly or in an
improper environment, overloaded, misused, opened, abused, or altered in any manner, or is not used under normal operating conditions or not in accordance with any labels or instructions. There are no other or implied warranties of any kind, including merchantability and fitness for
a particular purpose, but if any implied warranty is required by the applicable jurisdiction, the duration of any such implied warranty, including merchantability and fitness for a particular purpose, is limited to five years. Leviton is not liable for incidental, indirect, special, or consequential
damages, including without limitation, damage to, or loss of use of, any equipment, lost sales or profits or delay or failure to perform this warranty obligation. The remedies provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise.
FOR CANADA ONLY
For warranty information and/or product returns, residents of Canada should
contact Leviton in writing at Leviton Manufacturing of Canada Ltd to the
attention of the Quality Assurance Department, 165 Hymus Blvd, Pointe-
Claire (Quebec), Canada H9R 1E9 or by telephone at 1 800 405-5320.
3
2
4
1
2
3
4
1
5
5
Terminal
Screw Marked
Black (BK)
Terminal
Screw Marked
Red (RD)
Black Screw
(common)
Terminal
Screw Marked
Red (RD)
Dimmer 3-Way
Terminal
Screw Marked
Ground (GR)
Green
Ground
BKRD
Hot (Black)
Neutral (white)
Line
120VAC,
60Hz
RD
Black Screw
(common)
3-Way Dimmer
Move Slide
bar to Brighten
& Dim
Push
ON
Push
OFF
LED
Locator
Light
Bulb Selector
Switch
Locator Light
Switch
OFF
ON
LOC
AB
LOC
AB
Connect wires per WIRING DIAGRAM as follows:
• Green or bare copper wall box wire to terminal screw marked "GR".
• Common (Line hot or Load) wire to terminal screw marked "BK".
• Remove insulating label and connect the first traveler wire to the terminal
screw below marked "RD".
• Second traveler wire to the remaining terminal screw marked "RD".
Proceed to Step 5.
Connect wires per WIRING DIAGRAM as follows:
ON/OFF
Actuator
LOC
AB
Slide
Bar
OFF
ON
© 2014 Leviton Mfg. Co., Inc
Troubleshooting
Operation
Programming