RV-8 Receiver User Guide
IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or another apparatus (including amplifiers) that produces heat. 9.
Manufactured under license from Dolby Laboratories. “Dolby,” “Pro Logic,” “Surround EX,” and the double-D symbol are trademarks of Dolby Laboratories. Lexicon Inc. 3 Oak Park Bedford, MA 01730-1413 USA Tel 781-280-0300 Fax 781-280-0490 www.harmanspecialtygroup.com Customer Service Telephone: 781-280-0300 Sales Fax: 781-280-0495 Service Fax: 781-280-0499 Manufactured under license from Digital Theater Systems, Inc. U.S. Pat. No’s 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535 and other U.
Introduction Lexicon DOCUMENTATION CONVENTIONS This document contains general safety, installation and operation instructions for the RV-8 Receiver. It is important to read this user guide before attempting to use the product. Pay particular attention to safety instructions. The following symbols are used in the document: Appears on the component to indicate the presence of uninsulated, dangerous voltage inside the enclosure – voltage that may be sufficient to constitute a risk of shock.
Introduction RV-8 Table of Contents Documentation Conventions........................................................ ii Getting Started About the RV-8.......................................................................... 1-2 Highlights ............................................................................. 1-4 Product Registration .................................................................. 1-5 Installation Considerations.........................................................
Introduction Audio Controls Lexicon Restoring Factory-Default Settings .............................................7-4 Audio Controls ..........................................................................4-2 Appendix A Tuner Presets Tuner Presets .............................................................................5-2 Specifications ............................................................................A-2 Declaration of Conformity ......................................................
1 Getting Started About the RV-8........................................................................... 1-2 Highlights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 Product Registration ................................................................... 1-5 Installation Considerations.......................................................... 1-5 Remote Control Battery Installation ............................................
Getting Started Lexicon ABOUT THE RV-8 Thank you for purchasing the RV-8 Receiver, an 8-channel audio and video control center with independent zone monitoring that provides control of audio and video source selection in three zones at the same time. The RV-8 includes eight configurable inputs, each of which can be assigned to its built-in tuner, eight digital audio, eight analog audio, phono, five composite video, five S-Video or three component video input connectors.
RV-8 powerful processors perform custom Lexicon processing such as Logic 7 decoding, bass enhancement, dialogue enhancement, auto azimuth, five-speaker enhancement, bass management, highprecision digital crossovers and audio controls. These features are available at sample rates of up to 96kHz, with 24-bit resolution to retain top performance from all sources. In addition, a third DSP engine is dedicated to decoding multichannel compressed audio sources.
Getting Started Lexicon HIGHLIGHTS • Eight channels • Eight configurable inputs • Three independent zones • Integrated 7-channel amplifier with thermal and DC protection and toroidal power transformer • Compatible with 2Ω speaker impedances • Four S/PDIF coaxial and four S/PDIF optical (Toslink) digital audio input connectors • One S/PDIF coaxial and one S/PDIF optical (Toslink) digital audio output connectors • LIVE! (Lexicon Intelligent Variable Environment) • Dolby Digital Surround EX,
Getting Started RV-8 PRODUCT REGISTRATION Please register the RV-8 Receiver within 15 days of purchase. Register online at www.lexicon.com or complete and return the product registration card attached to the back cover of this user guide. Retain the sales receipt as proof of warranty coverage. INSTALLATION CONSIDERATIONS The RV-8 requires special care during installation to ensure optimal performance.
Getting Started Lexicon REMOTE CONTROL BATTERY INSTALLATION The remote control requires four AAA batteries. The batteries should be replaced as needed. Alkaline batteries, which last longer without leaking, are recommended. When battery power is low, the remote control enters a low-voltage condition, preventing it from operating the RV-8. When this occurs, replace the batteries. Normal operation will resume when new batteries are installed. To replace the remote control batteries: 1.
2 Basic Operation Front-Panel Overview ................................................................. 2-2 Rear-Panel Overview ................................................................... 2-6 Tuner Overview ........................................................................ 2-10 Selecting a Station...................................................................................2-10 Direct Station Access ...............................................................................
Basic Operation Lexicon FRONT-PANEL OVERVIEW The RV-8 is shown below. The numbers in the front-panel illustrations correspond with the numbered items in the text.
Basic Operation RV-8 1 FRONT-PANEL DISPLAY 3 VOLUME KNOB Use the front-panel display to view the current input, listening mode, input source and volume level. If the built-in tuner is active, the display will show the frequency, band, listening mode and volume level. The 2 x 20 character display also functions as a display for messages and menus, one line at a time. Use the volume knob to adjust volume level in all Zones. Note: Power is still supplied to the RV-8 when standby mode is activated.
Basic Operation FRONT-PANEL OVERVIEW Lexicon (continued) 4 MAIN ZONE INPUT SELECTION BUTTONS Selects the corresponding input in the Main Zone. When an input is selected, a blue LED lights on the corresponding input selection button. When the Main Zone is deactivated, pressing a Main Zone input selection button activates the corresponding input in the Main Zone. Zone 2 and Zone 3 remain deactivated until a Zone 2 or Zone 3 input is selected.
Basic Operation RV-8 11 MUTE BUTTON 14 ZONE 3 OFF BUTTON Mutes or restores the RV-8 Main Zone volume to its original level. Press the Mute button to mute volume level; “MUTE ON” appears in the on-screen and front-panel displays. Press the Mute button again to restore the volume to its original level. The VOLUME CONTROL SETUP and MUTE LEVEL parameter can be used to set mute levels. Deactivates Zone 3. Mute may be activated automatically or manually.
Basic Operation Lexicon REAR-PANEL OVERVIEW The RV-8 is shown below. The numbers in the rear-panel illustrations correspond with the numbered items in the text. 1 2 4 3 5 6 1 7 _ + _ + 8 9 10 11 12 13 14 15 16 17 18 19 20 CAUTION! Never make or break connections to the RV-8 unless the RV-8 and all associated components are powered off.
Basic Operation RV-8 1 AMPLIFIER OUTPUTS Provide audio outputs to the speakers. The Center channel output and all Right channel outputs are located on the left-hand side of the rear-panel. All Left channel outputs are located on the righthand side of the rear-panel. This organizaion facilitates making speaker connections.
Basic Operation REAR-PANEL OVERVIEW Lexicon (continued) 6 ZONE 2 VIDEO OUTPUT CONNECTORS 8 TUNER ANTENNA CONNECTORS Provide video output in Zone 2. One composite video connector and one S-Video connector is available. Alternatively, these connectors can be used to connect a video recording device. Provide two antenna connections for the AM/FM stereo radio tuner.
Basic Operation RV-8 putting the RV-8 into standby. The trigger output connector (labeled 1) can be configured for remote or program operation. See “Trigger Setup” on page 3-70 for more information. 17 ZONE 2 DIGITAL AUDIO OUTPUT CONNECTORS (S/PDIF) Provides digital audio output in Zone 2. One S/PDIF coaxial and one S/PDIF optical (Toslink) connector is available.
Basic Operation Lexicon TUNER OVERVIEW The RV-8 features an AM/FM stereo radio tuner. The front panel displays the currently selected frequency, band, listening mode and volume. Forty presets can store AM or FM frequencies, identified by the preset number/name and station frequency/band. For example: WABC/90.90 FM or Preset 02/10.30 AM. Two antennas are supplied with the RV-8: one for AM and one for FM stereo.
Basic Operation RV-8 SCAN MODE SAVING PRESETS Scan Mode scans through all available stations, pausing for two seconds on each station before scanning to the next one. The RV-8 has 40 presets available for storing AM or FM stations. The presets are divided into four banks with ten presets per bank. It is possible to store a combination of AM and FM stations in each bank. Storing presets on the RV-8 can be accomplished from either the front panel or the remote control. The operation is identical.
Basic Operation Lexicon For example, if Preset #01 is FM 90.90 and the call letters are WABC, then the name for that position is WABC. If Preset #23 does not broadcast their call letters, then that location is identified as Preset23 in the menu. AUTOLOAD EDITING PRESETS To start autoloading: It is possible to customize the name of each preset on the RV-8. 1. Select AUTOLOAD from the MAIN MENU : SETUP : TUNER SETUP menu. To edit the preset name: 2. Press menu 1.
Basic Operation RV-8 AMPLIFIER OVERVIEW The RV-8 features a 7-channel power amplifier with 140W per channel. The RV-8 can be configured so that all amplifier channels are dedicated to the Main Zone or so that outputs 3 and 7 (labeled Rear Right and Rear Left) are used for Zone 2 or Zone 3. Heavy duty gold plated 5-way binding posts are provided for speaker connections. The amplifiers feature advanced thermal current and DC protection for each channel.
Basic Operation Lexicon HEADPHONE OVERVIEW REMOTE CONTROL OVERVIEW Headphones can be connected to the RV-8 via the Headphone output on the front panel. The headphone output follows the signal selected in the Main Zone. If the Main Zone source is multichannel, a downmix of the source is sent to the headphone output. LOGIC7 headphone processing is also available for stereo or multichannel sources.
Basic Operation RV-8 MAIN MENU MENU ITEM SELECTION Use the MAIN MENU to open the four main menu branches: MODE ADJUST, AUDIO CONTROLS, TUNER PRESETS and SETUP. Use the remote-control Menu arrows to navigate menus and to select menu items. MAIN MENU MODE ADJUST AUDIO CONTROLS TUNER PRESETS SETUP To select a menu item on the open menu: 1. Press the remote-control menu item. MENU NAVIGATION Use the remote-control arrow buttons to navigate the extensive menu structure starting on page B-2.
Basic Operation Lexicon MENU OPTIONS Selecting a menu option opens another menu within the menu structure. For example, selecting SETUP from the MAIN MENU opens the SETUP menu. MAIN MENU SETUP MODE ADJUST AUDIO CONTROLS TUNER PRESETS SETUP INPUTS SPEAKERS I/O CONFIG D I S P L AY S V O L U ME C O N T R O L S TRIGGER TUNER SETUP L O C K O PT I O N S L I V E ! C A L I B R AT I O N P O W E R M A N A G E ME N T 2.
Basic Operation RV-8 REMOTE CONTROL BUTTONS 2 1 3 1. SYSTEM POWER OFF 2. Displays the name of the selected device. 3. POWER ON 4. Device and function buttons 4 4 5 6 7 11 8 9 5. Light 6. Displays page number/currently selected device 7. LCD page change 8. FAVORITE 9. HOME menu 10. CHANNEL/Listening Mode (+/-) 10 12 11. Previous channel 12. VOLUME (+/-) 13 14 13. MUTE 14. TRANSPORT functions (PLAY, STOP, REWIND, PAUSE, REC, SKIP and FF) for VCR, DVD and CD 15 15.
Basic Operation Lexicon COMMAND MATRIX The command matrix describes the commands that the remote control buttons perform when each command bank is active. 1 2 BUTTON 3 8 1 Enters RV-8 standby mode. 4 2 Activates the RV-8. 5 3 Displays the MAIN Zone Displays the command bank, which Main Zone includes commands Status. that control the Main Zone. Selects the Dolby Digital listening mode family. Displays the Zone 2 Toggles RV8 between Status. 5 speaker and 7 speaker modes.
Basic Operation RV-8 BUTTON 1 2 3 8 4 ZONE3 PAGE1 DVD1 PAGE1 DVD1 PAGE2 1 Enters RV-8 standby mode. Reserved for future expansion. 2 Activates the RV-8. Toggles RT-10 or RT-20 power. 3 Displays the Status of Zone 3. Resets the AUDIO CONTROLS menu BASS, TREBLE, and TILT EQ parameter to +0.0dB. Opens and closes the RT-10 or RT-20 disc tray. 4 Deactivates Zone 3. Decreases the AUDIO CONTROLS menu Main Zone BASS parameter in.5dB increments. Opens the RT-10 or RT-20 Top menu.
Basic Operation Lexicon 9 MAIN PAGE1 BUTTON HOME 9 Selects the VCR command bank, which includes commands that control the VCR. Selects the VCR input for the Main Zone. Selects the L7 Music listening mode. Selects the VCR input for Zone 2. Adjusts the Audio Controls menu Main Zone BALANCE parameter to the right. 10 Selects the TV command bank, which includes commands that control the TV. Selects the TV input for the Main Zone. Selects the L7 TV listening mode. Selects the TV input for Zone 2.
Basic Operation RV-8 BUTTON 9 ZONE3 PAGE1 13 16 14 DVD1 PAGE2 Increases the AUDIO CONTROLS menu BASS parameter in .5dB increments. Closes certain Setup menus without saving the changes. Activates and deactivates the RT-10 or RT-20 rear- panel video output connectors. 10 Selects the TV input for Zone 3. Increases the AUDIO CONTROLS menu TREBLE parameter in .5dB increments. Activates the RT-10 or RT-20 display mode. Controls the brightness of front-panel display characters.
Basic Operation Lexicon BUTTON HOME 17 19 22 MAIN PAGE2 ZONE2 PAGE1 ZONE2 PAGE2 17 History-dependent* Decreases Main Zone volume level in 1dB increments. 18 History-dependent* Centers the AUDIO CONTROLS menu Toggles between fully muting Main Zone volume level and restoring Main BALANCE and FADER parameters. Zone volume level to its original level. 19 History-dependent* Toggles between muting Main Zone volume level and restoring Main Zone volume level to its original level.
Basic Operation RV-8 BUTTON 18 20 17 19 22 21 ZONE3 PAGE1 ZONE3 PAGE2 DVD1 PAGE1 DVD1 PAGE2 17 Decreases Zone 3 volume level in.1dB increments. Decreases Main Zone volume level in.1dB increments. 18 Activates the 5.1 THX, 5.1 THX Ultra2 or the THX SurEX listening mode when a 5.1-channel THX source is present. Activates Dolby PLIIx+THX when a stereo source is present. Toggles between fully muting the RV-8 Main Zone volume level and restoring Main Zone volume level to its original level.
Basic Operation Lexicon BUTTON 25 27 28 HOME MAIN PAGE1 MAIN PAGE2 ZONE2 PAGE1 ZONE2 PAGE2 25 History-dependent* 26 History-dependent* 27 History-dependent* When a DTS(-ES) source is present, toggles the ES decoding parameter, cycling through the AUTO, ON, and OFF settings. 28 History-dependent* Deactivates the output connector labeled Trigger 1. 29 History-dependent* Activates the Dolby DIGITAL EX or Dolby DIGITAL listening mode when a 5.1- channel Dolby Digital source is present.
Basic Operation RV-8 BUTTON 25 26 25 27 28 ZONE3 PAGE2 If the RV-8’s built-in tuner is the currently o nce to tune to the next selected input, press available tuner frequency. Pressing for 2 seconds activates seek mode, which searches for the next available radio station. To enter Scan Mode, press and hold until the display shows SCAN or SCAN . DVD1 PAGE1 DVD1 PAGE2 When RT-10 or RT-20 playback is activated, scans through the disc in reverse direction.
Basic Operation Lexicon BUTTON HOME 35 36 38 2-26 34 MAIN PAGE2 ZONE2 PAGE1 ZONE2 PAGE2 33 History-dependent* When a menu is open, closes the menu and (in most cases), opens the previous menu. Subsequent presses continue to close the current menu and open the previous menu until the MAIN MENU is closed. When no menus are open, shows the two-line status. 34 History-dependent* When a menu is open, closes the menu structure. When no menus are open, shows the 2-line status.
Basic Operation RV-8 BUTTON 34 35 35 36 37 ZONE3 PAGE2 DVD1 PAGE1 DVD1 PAGE2 33 When a menu is open, closes the menu and, in most cases, opens the previous menu. Subsequent presses continue to close the current menu and open the previous menu until the MAIN MENU is closed. When no menus are open, this button performs no function. Navigates to the left in the RT-10 or RT-20 menu structure. 34 When a menu is open, closes the menu structure. When no menus are open, shows the two-line status.
Basic Operation Lexicon UNDERSTANDING THE ZONES TWO-LINE STATUS The RV-8 features three zones of operation: the Main Zone, Zone 2 and Zone 3. The Main Zone controls audio and video signals in the primary listening space. Zone 2 controls digital and analog audio and composite or S-Video signals for a second zone or recording device. Zone 3 is designed to control analog audio and composite or S-video signals in an additional listening space.
Basic Operation RV-8 ZONE 3 TWO-LINE STATUS Opens in the on-screen and front-panel displays DVD1 ANLG whenever the RV-8 detects a Zone 3 status ZONE3 change. The Zone 3 two-line status indicates the current input, input source and volume level selected in Zone 3. VOL -34dB TUNER STATUS The Tuner status indicates the current frequency, band, listening mode and volume level. The Tuner status takes the place of the two-line status display for inputs using the built-in tuner.
Basic Operation Lexicon 2CH STATUS D STATUS Provides information about 2-channel input sources. Features L and R level meters. Provides information about Dolby Digital input sources. Features L, C, R, SL, SR and LFE level meters. Parameter Possible Settings Parameter Possible Settings INPUT The current input INPUT The current input MODE The current listening mode MODE The current listening mode INPUT TYPE ANLG, PCM CHANNELS 3/2.1, 3/2, 3/1, 2/2, 2/1, 2/0, 1/0 SAMPLE RATE 44.
Basic Operation RV-8 STATUS 5.1a BYPASS STATUS Provides information about DTS(-ES) input sources. Includes L, C, R, SL, SR, SB and LFE level meters. The SB level meter appears when a 6.1-channel input source is present, or when a 5.1-channel input source is present and the ES DECODING parameter is set to ON. Provides information about 5.1-channel analog input sources when the MAIN ADV menu ANALOG BYPASS parameter is set to ON.
Basic Operation Lexicon 2CH BYPASS STATUS DIGITAL STATUS Provides information about 2-channel analog input sources when the MAIN ADV menu 2-CH ANLG BYP parameter is set to ON. Provides information about digital input sources for which a sample rate is detected, but no audio is present in the input signal.
Basic Operation RV-8 5.1 ANALOG STATUS LIVE! STATUS Provides information about 5.1-channel analog input sources. Provides information about LIVE! input sources. Features L and R level meters.
Basic Operation Lexicon STATUS MENU PARAMETER DESCRIPTIONS 2.0 ENCODING MATRIX, NONE Indicates whether or not a matrix-encoded source is detected. When the parameter setting is MATRIX, a matrix-encoded source is detected. When the parameter setting is NONE, a matrix-encoded source is not detected. The RV-8 cannot automatically detect matrix encoding in non-flagged input sources. BIT RATE 32 to 640 kbps or 754 to 1509.7kbps Indicates the rate at which the input signal is encoded.
Basic Operation RV-8 INPUT SURR MIX LVL Indicates the selected input (e.g., DVD1). Indicates the relative surround channel level that was used during the mixing process. INPUT TYPE ANLG, BYP, PCM, MIC, --- Indicates the input source that is present. When the parameter setting is ANLG, a 2-channel analog audio source is present and the MAIN ADV menu 2-CH ANLG BYP parameter is set to OFF.
3 Setup Setup ..........................................................................................3-2 Input Setup.................................................................................3-4 Changing Input Names............................................................................. 3-5 Assigning Audio and Video Input Connectors ........................................... 3-7 Selecting Preferred Listening Modes........................................................
Setup Lexicon SETUP Selecting SETUP from the MAIN MENU opens the SETUP menu. I/O CONFIG SETUP MAIN MENU SETUP MODE ADJUST AUDIO CONTROLS TUNER PRESETS SETUP INPUTS SPEAKERS I/O CONFIG DISPLAYS VOLUME CONTROLS TRIGGER TUNER SETUP LOCK OPTIONS LIVE! CALIBRATION POWER MANAGEMENT Opens the I/O CONFIG menu, which is used to configure the analog audio input connectors as eight stereo connectors, one 5.1-channel and five stereo connectors, or two stereo and two 5.1-channel connectors.
Setup RV-8 TUNER SETUP SETUP TUNER SETUP POWER MANAGEMENT SETUP ON, OFF POWER MANAGEMENT Opens the TUNER SETUP menu, which is used to configure the AM/ FM tuner. See “TUNER SETUP” on page 3-72 for more information. Opens the POWER MANAGEMENT menu, which is used to automatically put the RV-8 into standby mode during brownouts. LOCK OPTIONS When set to ON, the RV-8 detects low voltage levels or a momentary loss of power and puts the device in standby mode.
Setup Lexicon INPUT SETUP SETUP INPUTS (INPUT) INPUT SETUP Selecting the SETUP menu INPUTS option prompts the selection of a desired input (e.g., DVD1). Selecting an input opens the corresponding INPUT SETUP menu, which is used to change the input name, assign audio and video input connectors, select preferred listening modes and configure advanced Main Zone and Zone 2 input settings.
Setup RV-8 CHANGING INPUT NAMES Selecting the INPUT SETUP menu NAME parameter opens the INPUT NAME menu, which is used to customize or restore the factory-default name of the selected input. Factory-default input names correspond to front-panel and remote-control input selection button labels.
Setup Lexicon MAIN MENU SETUP INPUT SETUP DVD1 INPUT SETUP DVD1 INPUT NAME MODE ADJUST AUDIO CONTROLS TUNER PRESETS SETUP INPUTS SPEAKERS I/O CONFIG DISPLAYS VOLUME CONTROLS TRIGGER TUNER SETUP LOCK OPTIONS LIVE! CALIBRATION POWER MANAGEMENT DVD1 DVD2 SAT VCR TV CD TUNER PHONO DVD1 NAME DIGITAL IN COAX-1 ANALOG IN NONE ANLG IN LVL AUTO VIDEO IN S-VIDEO-1 COMPONENT IN 1 2-CH FILM D 5.1 FILM FILM 5.1a 5.
Setup RV-8 ASSIGNING AUDIO and VIDEO INPUT CONNECTORS The RV-8 has eight configurable inputs, each of which can be assigned to its eight digital audio, eight analog audio, the built-in tuner, the phono input, five composite video, five S-Video or three component video input connectors.
Setup Lexicon ASSIGNING AUDIO and VIDEO INPUT CONNECTORS (continued) MAIN MENU SETUP INPUT SETUP DVD1 INPUT SETUP DVD1 ANALOG IN DVD1 ANALOG IN DVD1 ANALOG IN MODE ADJUST AUDIO CONTROLS TUNER PRESETS SETUP INPUTS SPEAKERS I/O CONFIG DISPLAYS VOLUME CONTROLS TRIGGER TUNER SETUP LOCK OPTIONS LIVE! CALIBRATION POWER MANAGEMENT DVD1 DVD2 SAT VCR TV CD TUNER PHONO NAME DVD1 DIGITAL IN COAX-1 ANALOG IN NONE ANLG IN LVL AUTO S-VIDEO-1 VIDEO IN 1 COMPONENT IN FILM 2-CH 5.1 FILM D FILM 5.1a 5.
Setup RV-8 MAIN MENU SETUP INPUT SETUP DVD1 INPUT SETUP DVD1 ANLG IN LVL MODE ADJUST AUDIO CONTROLS TUNER PRESETS SETUP INPUTS SPEAKERS I/O CONFIG DISPLAYS VOLUME CONTROLS TRIGGER TUNER SETUP LOCK OPTIONS LIVE! CALIBRATION POWER MANAGEMENT DVD1 DVD2 SAT VCR TV CD TUNER PHONO NAME DVD1 DIGITAL IN COAX-1 ANALOG IN NONE ANLG IN LVL AUTO VIDEO IN S-VIDEO-1 COMPONENT IN 1 2-CH FILM 5.1 FILM D FILM 5.1a 5.
Setup Lexicon ASSIGNING AUDIO and VIDEO INPUT CONNECTORS AUTO SETUP (continued) ON, OFF INPUTS DVD1 ANLG IN LVL AUTO SETUP Provides automatic adjustment of analog audio input levels. When set to ON, the RV-8 automatically monitors and optimizes input levels. When the input signal is too high, the RV-8 quickly decreases input levels to avoid overload. When the input signal is too low, the RV-8 slowly increases input levels to maximize signal-to-noise ratio and dynamic range.
Setup RV-8 VIDEO IN SETUP INPUTS COMPOSITE-1 TO 5, S-VIDEO-1 TO 5, NONE DVD1 VIDEO IN COMPONENT IN SETUP INPUTS COMPONENT-1 to 3, VIDEO, NONE DVD1 COMPONENT IN Opens the VIDEO IN menu, which is used to assign a composite or S-Video input connector for the selected input. The RV-8 has eight configurable inputs, each of which can be assigned to any of its five composite or five S-Video input connectors.
Setup Lexicon SELECTING PREFERRED LISTENING MODES Preferred listening modes can be pre-selected so that when a particular type of input source is played, the pre-selected listening mode is activated. The RV-8 allows five preferred listening modes for each Main Zone input: one listening mode each for 2-channel, Dolby Digital, DTS(-ES), 5.1a and MIC (LIVE!) sources. The table to the right indicates the INPUT SETUP menu parameters that can be used to select preferred listening modes.
Setup RV-8 When a preferred listening mode is selected, that listening mode is automatically activated whenever a new input is selected or an appropriate input source is present. For example, the following can occur when a preferred listening mode is activated (also refer to the corresponding menus on 3-12): If the DVD1 input is selected and a 2-channel source is played, the L7 FILM listening mode is activated. If a Dolby Digital source is played, the 5.1 L7 FILM listening mode is activated.
Setup SELECTING PREFERRED LISTENING MODES Lexicon (continued) The Use Last Parameter When the RV-8 is set to use a preferred listening mode for a selected input, selecting another mode from the Mode scroll list replaces the preferred selection. However, this newly selected mode will be lost when switching between inputs. The USE LAST parameter was designed to allow the RV-8 software to “remember” the last used listening mode for a given input source.
Setup RV-8 2-CH SETUP DOLBY D INPUTS DVD1 2-CH Opens the 2-CH MODE menu, which is used to select a preferred listening mode for 2-channel input sources. The RV-8 activates the selected listening mode whenever a 2-channel source is present. SETUP INPUTS DVD1 D Opens the DOLBY DIGITAL MODE menu, which is used to select a preferred listening mode for Dolby Digital input sources. The RV-8 activates the selected listening mode whenever a new input is selected or a new Dolby Digital source is present.
Setup Lexicon SELECTING PREFERRED LISTENING MODES (continued) 5.1a SETUP INPUTS SETUP DVD1 INPUTS DVD1 5.1a Opens the DTS(-ES) MODE menu, which is used to select a preferred listening mode for DTS(-ES) input sources. The RV-8 automatically activates the selected listening mode whenever a new input is selected or a new DTS(-ES) source is present. Opens the 5.1a MODE menu, which is used to select a preferred listening mode for 5.1-channel analog sources.
Setup RV-8 CONFIGURING ADVANCED INPUT SETTINGS MAIN MENU SETUP INPUT SETUP DVD1 INPUT SETUP DVD1 MAIN ADV MODE ADJUST AUDIO CONTROLS TUNER PRESETS SETUP INPUTS SPEAKERS I/O CONFIG DISPLAYS VOLUME CONTROLS TRIGGER TUNER SETUP LOCK OPTIONS LIVE! CALIBRATION POWER MANAGEMENT DVD1 DVD2 SAT VCR TV CD TUNER PHONO NAME DVD1 DIGITAL IN COAX-1 ANALOG IN NONE ANLG IN LVL AUTO S-VIDEO-1 VIDEO IN 1 COMPONENT IN FILM 2-CH 5.1 FILM D FILM 5.1a 5.
Setup Lexicon CONFIGURING ADVANCE INPUT SETTINGS (continued) ANALOG BYPASS SETUP INPUTS DVD1 ON, OFF MAIN ADVANCED ANALOG BYPASS When set to ON, the RV-8 passes the analog input signal to the Main Zone audio output connectors. For stereo analog sources, the input is sent to the FRONT L/R outputs. For a 5.1-channel analog source, the (L) input is sent to the FRONT L output. The (R) input is sent to the FRONT R output. The (C) input is sent to the center output.
Setup RV-8 INPUT SELECT PARAMETER SETTINGS DIGITAL ANALOG AUTO The RV-8 sends the assigned digital audio input connector to the Main Zone audio output connectors. The RV-8 ignores the assigned analog audio input connector. The RV-8 sends the assigned analog audio input connector to the Main Zone audio output connectors. The RV-8 ignores the digital audio input connector.
Setup Lexicon CONFIGURING ADVANCE INPUT SETTINGS (continued) S-VIDEO OSD 4:3 SETUP INPUTS DVD1 ON, OFF MAIN ADVANCED S-VIDEO OSD 4-3 Controls the appearance of the on-screen display when the display device is connected to an S-Video output connector. When set to ON, the display device shows the on-screen display in a 4:3 aspect ratio, regardless of the incoming signal.
Setup RV-8 LEGACY VIDEO SETUP INPUTS A, B DVD1 MAIN ADVANCED LEGACY VIDEO ZONE2 IN SETUP INPUTS DIGITAL, ANLG, DMIX DVD1 ZONE2 IN When video played back from a VCR is converted to component video by the RV-8, the resulting picture quality depends on both the quality of the VCR playback and the capabilities of the component display device. The LEGACY VIDEO menu item has two selections, A and B. Use the one that gives the best picture for the Combination of the VCR and display device.
Setup Lexicon ZONE2 IN PARAMETER SETTINGS DIGITAL • The RV-8 automatically sets the ZONE2 IN parameter to DIGITAL when the ANALOG IN parameter is set to NONE. • The RV-8 sends the assigned D I G I TA L I N c o n n e c t o r specified in the INPUT SETUP menu to the ZONE 2 ANALOG and DIGITAL AUDIO OUTPUTS. • • 3-22 Only PCM digital input sources are compatible with ZONE 2 analog audio outputs.
Setup RV-8 ZONE2 ADVANCED SETUP INPUTS DVD1 ZONE2 ADVANCED Opens the ZONE2 IN menu, which is used to configure advanced MAIN MENU SETUP INPUT SETUP DVD1 INPUT SETUP DVD1 ZONE2 ADVANCED MODE ADJUST AUDIO CONTROLS TUNER PRESETS SETUP INPUTS SPEAKERS I/O CONFIG DISPLAYS VOLUME CONTROLS TRIGGER TUNER SETUP LOCK OPTIONS LIVE! CALIBRATION POWER MANAGEMENT DVD1 DVD2 SAT VCR TV CD TUNER PHONO NAME DVD1 DIGITAL IN COAX-1 ANALOG IN NONE ANLG IN LVL AUTO VIDEO IN S-VIDEO-1 COMPONENT IN 1 2-CH FILM D 5.
Setup Lexicon DIGITAL BYPASS SETUP INPUTS ON, OFF DVD1 ZONE2 ADVANCED DIGITAL BYPASS Allows digital sources to bypass decoding for direct digital recording. When ON is selected, the RV-8 passes digital input signals directly to the Zone 2 digital audio output connectors, preserving the original format of the input signal. This would be useful if you want to send a multichannel-encoded signal to a second device for decoding.
Setup RV-8 SPEAKER SETUP SETUP SPEAKERS Select the SPEAKER SETUP menu to configure the Main Zone audio output connectors for the desired speaker setup. The Main Zone includes eight audio output connectors labeled Front L/R, Center, Subwoofer, Side L/R and Rear L/R.
Setup Lexicon CUSTOM SPEAKER SETUPS Selecting the CROSSOVER SETUP menu CUSTOM SETUP option opens the CUSTOM SETUP menu, which assigns independent crossover points for each Main Zone audio output connector. Possible crossover settings include FULL, FULL + SUB, and 10Hz increments within a 30Hz to 120Hz range. The graphs shown on the next page indicate the frequency response of each crossover point.
Setup RV-8 In general, low frequencies will be redirected from speakers with the highest crossover points to speakers with the lowest crossover points. Lowfrequency signals lower than the lowest crossover point will be redirected to the subwoofer. If the lowest crossover point is FULL, low frequency signals, excluding LFE information, will not be redirected to the subwoofer. High-Pass Filter High-pass filters attenuate low frequencies at 24dB per octave.
Setup Lexicon THX SPEAKER SETUPS Selecting THX SETUP opens the THX SPEAKER SETUP screen, which indicates that pressing the arrow button will automatically configure the Main Zone audio output connectors for a THX speaker setup. Use THX-certified speakers in a THX speaker setup.
Setup RV-8 SPEAKER SETUP PARAMETERS SETUP SPEAKERS SET CROSSOVERS CUSTOM SETUP or SETUP The table below indicates the speaker setup parameters for configuring the Main Zone audio output connectors for the desired speaker setup. These parameters are available in the CUSTOM SETUP and THX SETUP menus. SPEAKERS SET CROSSOVERS THX SETUP Speaker setup parameters perform the same function regardless of the selected speaker setup.
Setup Lexicon SPEAKER SETUP PARAMETERS (continued) MAIN MENU SETUP SPEAKER SETUP CROSSOVER SETUP CUSTOM SETUP MODE ADJUST AUDIO CONTROLS TUNER PRESETS SETUP INPUTS SPEAKERS I/O CONFIG DISPLAYS VOLUME CONTROLS TRIGGER TUNER SETUP LOCK OPTIONS LIVE! CALIBRATION POWER MANAGEMENT SET CROSSOVERS CHECK MICROPHONES AUTOMATIC MANUAL CUSTOM SETUP THX SETUP FRONT L/R CENTER SIDE L/R REAR L/R SUBWOOFER ULTRA2 SUB BGC ASA R SET CROSSOVERS BEFORE CALIBRATING RR 80Hz C 80Hz M SUB 80Hz 3-30 SR 80Hz 80H
Setup RV-8 FRONT L/R SETUP SPEAKERS FULL, FULL + SUB, 30 to 120HZ, THX 80HZ SET CROSSOVERS CUSTOM SETUP FRONT L/R CENTER SETUP FULL, FULL + SUB, 30 to 120HZ, THX 80HZ, NONE SPEAKERS SET CROSSOVERS CUSTOM SETUP CENTER Assigns a crossover point for the Main Zone audio output connectors labeled Front L/R when a custom speaker setup is selected. Opens the FRONT L/R SPEAKERS menu to select a crossover point for the Front L/R output connectors.
Setup Lexicon SPEAKER SETUP PARAMETERS SIDE L/R SETUP (continued) FULL, FULL + SUB, 30 to 120Hz, THX 80Hz, NONE SPEAKERS SET CROSSOVERS CUSTOM SETUP SIDE L/R Assigns a crossover point for the Main Zone audio output connectors labeled SIDE L/R when a custom speaker setup is selected. • Select FULL to send a full-range signal to the side speakers. Otherwise, select the crossover point closest to the lowfrequency rating of the side speakers.
Setup RV-8 MAIN MENU SETUP SPEAKER SETUP CROSSOVER SETUP CUSTOM SETUP MODE ADJUST AUDIO CONTROLS TUNER PRESETS SETUP INPUTS SPEAKERS I/O CONFIG DISPLAYS VOLUME CONTROLS TRIGGER TUNER SETUP LOCK OPTIONS LIVE! CALIBRATION POWER MANAGEMENT SET CROSSOVERS CHECK MICROPHONES AUTOMATIC MANUAL CUSTOM SETUP THX SETUP FRONT L/R CENTER SIDE L/R REAR L/R SUBWOOFER ULTRA2 SUB BGC ASA R SET CROSSOVERS BEFORE CALIBRATING SETUP SPEAKERS RR 60Hz C 60Hz M SUB 40Hz SUBWOOFER SR 60Hz 40Hz L 40Hz SL 60Hz
Setup Lexicon SPEAKER SETUP PARAMETERS (continued) MAIN MENU SETUP SPEAKER SETUP CROSSOVER SETUP MODE ADJUST AUDIO CONTROLS TUNER PRESETS SETUP INPUTS INPUTS SPEAKERS SPEAKERS I/O CONFIG I/O CONFIG DISPLAYS DISPLAYS VOLUME CONTROLS VOLUME CONTROLS TRIGGER TRIGGERS TUNER SETUP TUNER SETUP LOCK OPTIONS LOCK OPTIONS LIVE! CALIBRATION POWER MANAGEMENT SET CROSSOVERS CHECK MICROPHONES AUTOMATIC MANUAL CUSTOM SETUP THX SETUP R SET CROSSOVERS BEFORE CALIBRATING THX SETUP !CAUTION! PRESSING THE BUTTO
Setup RV-8 BGC (BOUNDARY GAIN COMPENSATION) SETUP SPEAKERS CUSTOM SETUP SETUP SPEAKERS THX SETUP ON, OFF BGC BGC ASA (ADVANCED SPEAKER ARRAY) APART, CLOSE, TOGETHER SETUP SPEAKERS CUSTOM SETUP SETUP SPEAKERS THX SETUP ASA ASA Adjusts boundary gain compensation when the CUSTOM and THX SETUP menu THX ULTRA2 SUB parameter is set to ON. When the BGC parameter is set to ON, a highpass 55Hz filter is applied to all audio output connectors for all Main Zone listening modes.
Setup Lexicon AUTOMATIC CALIBRATION The RV-8 offers automatic calibration of speaker distances, output level, or both. The table below indicates available automatic calibration options. A successful microphone check is required before automatic calibration can be performed. Automatic Options Details MICROPHONE CHECK • Confirms that the microphones are properly connected and functioning.
Setup RV-8 CONNECTING THE MICROPHONES CAUTION! To connect the microphones: • 4. Make sure the RV-8 is powered off OR in standby mode. The microphones included in the Lexicon Microphone Kit require careful handling. Dropping or otherwise physically abusing the microphones might cause errors during use or irreparable damage to the microphones. • The microphone wires also require careful handling. Do not sharply bend the wires or place objects on them.
Setup Lexicon POSITIONING THE MICROPHONES FOR THE MICROPHONE CHECK Refer to the microphone placement examples that begin below to position the microphones for the microphone check.
Setup RV-8 IMPROPER microphone positioning for the microphone check During the microphone check, DO NOT: 7 Separate the microphones 7 Scatter the microphones throughout the listening space 7 Obstruct the line-of-sight path between the microphones and the speakers 7 Position the microphones on the floor, on seat cushions, or in locations obstructed by furniture and other fixtures, where echoes might obscure calibration noise signals Rear Left 7 Position the microphones within 2 feet (0.
Setup Lexicon CHECKING THE MICROPHONES MAIN MENU MODE ADJUST AUDIO CONTROLS TUNER PRESETS SETUP SETUP SPEAKER SETUP INPUTS SPEAKERS I/O CONFIG DISPLAYS VOLUME CONTROLS TRIGGER TUNER SETUP LOCK OPTIONS LIVE! CALIBRATION POWER MANAGEMENT SET CROSSOVERS CHECK MICROPHONES AUTOMATIC MANUAL SET CROSSOVERS BEFORE CALIBRATING CUSTOM CHECK MICROPHONES SETUP GROUP MICROPHONES 40 Hz INTO A BUNDLE 60 Hz IN THE 60THE Hz ROOM MIDDLE OF 60 Hz PRESS 40TOHzBEGIN OFF MIC CHECK N/A APART Note the following: • • • T
Setup RV-8 CHECKING MICROPHONES Appears in the on-screen display while CUSTOM CHECK MICROPHONES SETUP the RV-8 confirms the microphone level CHECKING MICROPHONES calculated during the silence check. To PLEASE WAIT do this, the RV-8 sends alternating calibration noise signals to the front left and right speakers. These signals are output between 55dB and 95dB, beginning with 55dB and increasing in 5dB increments until the microphones detect the required level.
Setup Lexicon CHECKING THE MICROPHONES Message (continued) Description Troubleshooting (MICROPHONE) OK The microphone detected the calibration noise signal without error. • N/A (MICROPHONE) NOT DETECTED The RV-8 did not detect the microphone during the silence check. • Examine microphone input connections to ensure that the microphones are properly connected to the RV-8 and that microphone cable plugs are fully inserted for a solid connection. • The microphone may be damaged.
Setup RV-8 PROPER microphone placement to achieve the best results for a single listening position When calibrating for a single listening position, place the microphones: 3 As close together as possible in a single listening position (the primary listening position) 3 At the approximate spot where the listener’s head will be during listening Rear Left 3 In a clear line-of-sight path with the speakers 3 In a location unobstructed by furniture and other fixtures, where echoes will not obscure calibration
Setup Lexicon POSITIONING THE MICROPHONES FOR AUTOMATIC CALIBRATION (continued) PROPER microphone placement to achieve the best results for multiple listening positions in a single row When calibrating for multiple listening positions in a single row, position the microphones: 3 At the approximate spot where the listener’s head will be during listening 3 In a clear line-of-sight path with the speakers 3 In a location unobstructed by furniture and other fixtures, where echoes will not obscure calibration
Setup RV-8 PROPER microphone placement to achieve the best results for multiple listening positions in multiple rows When calibrating for multiple listening positions in multiple rows, position the microphones: 3 At the approximate spot where the listener’s head will be during listening 3 In a clear line-of-sight path with the speakers 3 In a location unobstructed by furniture and other fixtures, where echoes will not obscure calibration noise signals Rear Left 3 At least 2 feet (0.
Setup Lexicon POSITIONING THE MICROPHONES FOR AUTOMATIC CALIBRATION (continued) IMPROPER microphone positioning for automatic calibration During the automatic calibration, do not: 7 Arrange the microphones along the perimeter of the listening positions or space 7 Position the microphones in spots where the listeners’ heads will not be during listening Rear Left 7 Obstruct the line-of-sight path between the microphones and the speakers 7 Position the microphones on the floor, on seat cushions, or in loc
Setup RV-8 IMPROPER microphone positioning for automatic calibration During the automatic calibration, do not: 7 Arrange the microphones along the perimeter of the listening positions or space 7 Position the microphones at spots where the listeners’ heads will not be during listening 7 Obstruct the line-of-sight path between the microphones and the speakers Rear Left 7 Position the microphones on the floor, on seat cushions, or in locations obstructed by furniture and other fixtures, where echoes might
Setup Lexicon PERFORMING AUTOMATIC CALIBRATION MAIN MENU SETUP SPEAKER SETUP MODE ADJUST AUDIO CONTROLS TUNER PRESETS SETUP INPUTS SPEAKERS I/O CONFIG DISPLAYS VOLUME CONTROLS TRIGGER TUNER SETUP LOCK OPTIONS LIVE! CALIBRATION POWER MANAGEMENT SET CROSSOVERS CHECK MICROPHONES AUTOMATIC MANUAL CUSTOM AUTO SPEAKER SETUP SETUP SET CROSSOVERS BEFORE CALIBRATING DISTANCES 40 & LEVELS Hz DISTANCES 60 Hz 60 Hz OUTPUT LEVELS 60 Hz 40 Hz PLACE MICROPHONES AROUND PREFERRED OFF LISTENING POSITIONS N/A APART
Setup RV-8 SETTING SETUP DISTANCES CUSTOM FRONT LEFT CENTER FRONT RIGHT SIDE RIGHT REAR RIGHT REAR LEFT SIDE LEFT SUBWOOFER STEP SETTING SETUP DISTANCES CUSTOM 0.0ft 0.0ft 0.0ft 0.0ft 0.0ft 0.0ft 0.0ft 0.0ft FRONT LEFT CENTER FRONT RIGHT SIDE RIGHT REAR RIGHT REAR LEFT SIDE LEFT SUBWOOFER DISTANCES SETTING SETUP LEVELS CUSTOM 12.0ft 10.5ft 12.0ft 4.5ft ERROR 6.0ft 4.5ft N/A FRONT LEFT CENTER FRONT RIGHT SIDE RIGHT REAR RIGHT REAR LEFT SIDE LEFT SUBWOOFER SETTING SETUP LEVELS CUSTOM 0.0dB 0.0dB 0.
Setup Lexicon PERFORMING AUTOMATIC CALIBRATION (continued) STEP DISTANCES & LEVELS DISTANCES AUTO DISTANCES FRONT LEFT CENTER FRONT RIGHT SIDE RIGHT REAR RIGHT REAR LEFT SIDE LEFT SUBWOOFER FRONT LEFT 12.0ft 10.5ft 12.0ft 4.5ft ERROR 6.0ft 4.5ft N/A 5 • A value indicates that no errors occurred during the calibration procedure. • An ERROR message indicates that a value was calculated, but at least one error occurred during the calibration procedure.
Setup RV-8 STEP DISTANCES SET DISTANCES AUTO DISTANCES AUTO DISTANCES ORIGINAL DISTANCES FRONT LEFT CENTER FRONT RIGHT SIDE RIGHT REAR RIGHT REAR LEFT SIDE LEFT SUBWOOFER R SR RR 0.0ft 0.0ft 0.0ft C 0.0ft M SUB 0.0ft 6 L 0.0ft DISTANCES & LEVELS 12.0ft 10.5ft 12.0ft 4.5ft ERROR 6.0ft 4.
Setup Lexicon PERFORMING AUTOMATIC CALIBRATION (continued) Message Description Troubleshooting The RV-8 successfully calibrated the value for the selected speaker without error. • N/A (SPEAKER) SPEAKER IS NOT ENABLED The selected speaker is not present in the speaker setup. • Set the corresponding CUSTOM or THX SETUP menu parameter to include the selected speaker in the speaker setup. (The RV-8 only calibrates values for speakers that are included in the speaker setup.
Setup RV-8 MANUAL CALIBRATION SETUP SPEAKERS MANUAL Selecting the SPEAKER SETUP menu MANUAL option displays the MANUAL SPEAKER SETUP menu, to manually calibrate speaker distances and output levels. The table below indicates available manual calibration options.
Setup Lexicon PERFORMING MANUAL SPEAKER DISTANCE CALIBRATION SETUP SPEAKERS MANUAL SPEAKER DISTANCES Selecting the MANUAL SPEAKER SETUP menu SPEAKER DISTANCES option displays the SPEAKER DISTANCES menu, to manually calibrate speaker distances.
Setup RV-8 PERFORMING MANUAL OUTPUT LEVEL CALIBRATION SETUP SPEAKERS MANUAL LEVELS CALIBRATION Selecting the MANUAL SPEAKER SETUP menu LEVELS CALIBRATION option displays the LEVELS CALIBRATION menu shown below, to manually calibrate output levels.
Setup Lexicon INTERNAL NOISE TEST SETUP SPEAKERS MANUAL LEVELS CALIBRATION INTERNAL NOISE TEST Opens the INTERNAL NOISE message shown on the previous page, which indicates that the internal noise test generates loud calibration noise signals. To manually calibrate output levels during the internal noise test: 1. Set the SPL meter to “C” weighting and “SLOW” response. 2. Place the SPL meter at the primary listening position.
Setup RV-8 EXTERNAL NOISE TEST SETUP SPEAKERS MANUAL LEVELS CALIBRATION EXTERNAL NOISE TEST Selecting the LEVELS CALIBRATION menu EXTERNAL NOISE TEST option opens the SPEAKER LEVEL ADJUST menu shown on page 3-55, which manually calibrates output levels. The external noise test requires an external calibration source such as an audio calibration disc. When the external noise test is conducted, the RV-8 activates a listening mode based on the current Main Zone input source.
Setup Lexicon SETTING BASS PEAK LIMITERS SETUP SPEAKERS MANUAL LEVELS CALIBRATION BASS PEAK LIMITERS The BASS PEAK LIMITERS option displays the BASS PEAK LIMITERS menu, to set amplitude limits on low-frequency signals sent to the Main Zone audio output connectors, including the Subwoofer. The RV-8 is equipped with an internal limiter to prevent low-frequency signals from exceeding a designated output level.
Setup RV-8 LIMITER SETUP SPEAKERS ON, OFF MANUAL LEVELS CALIBRATION BASS PEAK LIMITERS LIMITER Limits low-frequency signals sent to the subwoofer or redirected to other speakers. To set the LIMITER parameter: • Select ON to restrict the output level of the low-frequency signals to the LIMIT ADJ parameter setting. • Select OFF to allow an unrestricted signal output level, regardless of the LIMIT ADJ parameter setting.
Setup Lexicon I/O CONFIG SETUP I/O CONFIG The I/O CONFIG option is used to configure the analog audio input connectors as eight (Left/Right) stereo connectors, five (Left/Right) stereo connectors and one 5.1-channel configuration (Front L/R, Center, Subwoofer, Side L/R), or as two stereo connectors and two 5.1-channel configurations.
Setup RV-8 5 ST. & (1) 5.1 ANLG SETUP I/O CONFIG ANALOG INPUTS 2 ST. & (2) 5.1 ANLG SETUP 5 ST. & (1) 5.1 ANLG I/O CONFIG ANALOG INPUTS 2 ST. & (2) 5.1 ANLG Configures the analog audio input connectors as five stereo connectors and one 5.1-channel configuration. Configures the analog audio input connectors as two stereo connectors and two 5.1-channel configurations. When the analog audio input connectors are configured as five stereo and one 5.
Setup Lexicon I/O CONFIG (continued) MAIN MENU SETUP I/O CONFIG AMP OUTPUTS MODE ADJUST AUDIO CONTROLS TUNER PRESETS SETUP INPUTS SPEAKERS I/O CONFIG DISPLAYS VOLUME CONTROLS TRIGGER TUNER SETUP LOCK OPTIONS LIVE! CALIBRATION POWER MANAGEMENT ANALOG INPUTS AMP OUTPUTS MAIN 7.1 MAIN 5.1 & ZONE2 2.0 MAIN 5.1 & ZONE3 2.0 MAIN 7.1 SETUP I/O CONFIG MAIN 5.1 & ZONE3 2.0 AMP INPUTS MAIN 7.1 SETUP I/O CONFIG AMP INPUTS MAIN 5.1 & ZONE3 2.0 When set to MAIN 7.
Setup RV-8 DISPLAY SETUP SETUP DISPLAYS Selecting the SETUP menu DISPLAYS option opens the DISPLAY SETUP menu, which is used to customize the on-screen and front-panel displays, restore audio/video synchronization, and activate and create a custom unit name.
Setup Lexicon ON-SCREEN DISPLAY SETUP SETUP DISPLAYS ON-SCREEN DISPLAY Opens the ON-SCREEN DISPLAY menu, which is used to customize the on-screen display.
Setup RV-8 POSITION SETUP DISPLAYS TOP, CENTER, BOTTOM ON-SCREEN DISPLAY POSITION Controls the vertical position of the two-line status on the display device screen. When set to TOP, the two-line status appears near the top of the display device screen. When set to CENTER, the two-line status is centered on the display device screen. When set to BOTTOM, the two-line status appears near the bottom of the display device screen. Refer to page 2-28 for more information about the two-line status.
Setup Lexicon FRONT-PANEL DISPLAY SETUP Opens the FRONT PANEL DISPLAY menu, which is used to customize the front-panel display.
Setup RV-8 MAIN MENU SETUP DISPLAY SETUP MODE ADJUST AUDIO CONTROLS TUNER PRESETS SETUP INPUTS SPEAKERS I/O CONFIG DISPLAYS VOLUME CONTROLS TRIGGER TUNER SETUP LOCK OPTIONS LIVE! CALIBRATION POWER MANAGEMENT ON-SCREEN DISPLAY FRONT PANEL DISPLAY A/V SYNC DELAY OFF CUSTOM NAME OFF EDIT CUSTOM NAME A/V SYNC DELAY SETUP DISPLAYS OFF, 1 to 60ms EDIT CUSTOM NAME RV-8 > ON OFF BUTTONS TO EDIT UP TO 20 CHARACTERS BUTTON TO ADVANCE OFF, 1 to 60ms EDIT CUSTOM NAME SETUP A/V SYNC DELAY DISPLAYS EDIT
Setup Lexicon VOLUME CONTROL SETUP SETUP VOLUME CONTROLS Opens the VOLUME CONTROL SETUP menu, which is used to configure Main Zone, Zone 2, Zone 3, and Headphone volume levels.
Setup RV-8 Z3 PWR ON SETUP VOLUME CONTROLS LAST LVL, –80 to +12dB ZONE PWR ON Sets the Zone 3 volume level that will be selected whenever Zone 3 is activated. When set to LAST LVL, Zone 3 activates at the volume level that was last selected in the previous operating session. LAST LVL is displayed on power up if the Zone 3 was powered off using the Zone 3 Off button on the remote control or front panel.
Setup Lexicon TRIGGER SETUP SETUP TRIGGER Selecting the SETUP menu TRIGGER option opens the TRIGGER SETUP menu shown to the right, which can be used to configure the trigger output connector labeled 1. The RV-8 rear panel houses two 12V DC trigger output connectors. The connector labeled PWR – the power trigger output connector – is not configurable. It is activated when the RV-8 is activated, and deactivated when the RV-8 is deactivated.
Setup RV-8 PROGRAM OPERATION PARAMETERS SETUP TRIGGER ON, OFF (PROGRAM OPERATION PARAMETER) Configure the trigger output connector labeled 1 for program operation. All TRIGGER SETUP menu parameters– except the REMOTE ONLY parameter–are considered program operation parameters. The connector can be associated with multiple inputs and listening modes at the same time.
Setup Lexicon TUNER SETUP SETUP TUNER SETUP Selecting the SETUP menu TUNER SETUP option opens the TUNER SETUP menu, which is used to configure the AM/FM radio tuner.
Setup RV-8 MAIN MENU SETUP TUNER SETUP MODE ADJUST AUDIO CONTROLS TUNER PRESETS SETUP INPUTS SPEAKERS I/O CONFIG DISPLAYS VOLUME CONTROLS TRIGGER TUNER SETUP LOCK OPTIONS LIVE! CALIBRATION POWER MANAGEMENT REGION USA SCAN SENS LOW AUTOLOAD CLEAR ALL TUNER PRESETS DISPLAY RDS NAME RADIO TEXT ON SCROLL RATE MEDIUM AUTO FREQUENCY ON SCAN SENS SETUP TUNER SETUP LOW MED HIGH LOW, MED, HIGH REGION Selects the Scan Sensitivity parameter, which can be used to set the threshold the system will use to tun
Setup Lexicon TUNER SETUP (continued) MAIN MENU SETUP TUNER SETUP MODE ADJUST AUDIO CONTROLS TUNER PRESETS SETUP INPUTS SPEAKERS I/O CONFIG DISPLAYS VOLUME CONTROLS TRIGGER TUNER SETUP LOCK OPTIONS LIVE! CALIBRATION POWER MANAGEMENT USA REGION LOW SCAN SENS AUTOLOAD CLEAR ALL TUNER PRESETS DISPLAY RDS NAME RADIO TEXT ON SCROLL RATE MEDIUM AUTO FREQUENCY ON PRESS RIGHT J TO START AUTOLOAD AUTOLOAD SETUP TUNER SETUP AUTOLOAD Automatically scans and stores presets for the currently selected frequ
Setup RV-8 MAIN MENU SETUP TUNER SETUP MODE ADJUST AUDIO CONTROLS TUNER PRESETS SETUP INPUTS SPEAKERS I/O CONFIG DISPLAYS VOLUME CONTROLS TRIGGER TUNER SETUP LOCK OPTIONS LIVE! CALIBRATION POWER MANAGEMENT REGION USA SCAN SENS LOW AUTOLOAD CLEAR ALL TUNER PRESETS DISPLAY RDS NAME RADIO TEXT ON SCROLL RATE MEDIUM AUTO FREQUENCY ON CLEAR ALL SETUP TUNER SETUP PRESS RIGHT J TO CLEAR ALL PRESETS TUNER PRESETS CLEAR ALL SETUP Clears all of the presets.
Setup Lexicon TUNER SETUP (continued) DISPLAY SETUP TUNER SETUP MAIN MENU SETUP TUNER SETUP MODE ADJUST AUDIO CONTROLS TUNER PRESETS SETUP INPUTS SPEAKERS I/O CONFIG DISPLAYS VOLUME CONTROLS TRIGGER TUNER SETUP LOCK OPTIONS LIVE! CALIBRATION POWER MANAGEMENT REGION USA SCAN SENS LOW AUTOLOAD CLEAR ALL TUNER PRESETS DISPLAY RDS NAME RADIO TEXT ON SCROLL RATE MEDIUM AUTO FREQUENCY ON RDS NAME, PRESET NAME, FREQUENCY DISPLAY Identifies the current channel setting, in the top right corner of the OS
Setup RV-8 MAIN MENU SETUP TUNER SETUP MODE ADJUST AUDIO CONTROLS TUNER PRESETS SETUP INPUTS SPEAKERS I/O CONFIG DISPLAYS VOLUME CONTROLS TRIGGER TUNER SETUP LOCK OPTIONS LIVE! CALIBRATION POWER MANAGEMENT REGION USA SCAN SENS LOW AUTOLOAD CLEAR ALL TUNER PRESETS DISPLAY RDS NAME RADIO TEXT ON SCROLL RATE MEDIUM AUTO FREQUENCY ON RADIO TEXT SETUP TUNER SETUP ON, OFF RADIO TEXT SCROLL RATE SETUP Activates the RADIO TEXT (RT) feature.
Setup Lexicon TUNER SETUP (continued) MAIN MENU SETUP TUNER SETUP MODE ADJUST AUDIO CONTROLS TUNER PRESETS SETUP INPUTS SPEAKERS I/O CONFIG DISPLAYS VOLUME CONTROLS TRIGGER TUNER SETUP LOCK OPTIONS LIVE! CALIBRATION POWER MANAGEMENT USA REGION LOW SCAN SENS AUTOLOAD CLEAR ALL TUNER PRESETS DISPLAY RDS NAME RADIO TEXT ON SCROLL RATE MEDIUM AUTO FREQUENCY ON AUTO FREQUENCY SETUP TUNER SETUP ON, OFF AUTO FREQUENCY Checks for alternate frequency broadcasts in case of station drop out or signal fade
Setup RV-8 LOCK OPTIONS SETUP LOCK OPTIONS Selecting the SETUP menu LOCK OPTIONS option opens the LOCK OPTIONS menu, which is used to protect MODE ADJUST, AUDIO CONTROLS and SETUP menu branch parameter settings from accidental changes.
Setup Lexicon LIVE! CALIBRATION SETUP LIVE! CALIBRATION LIVE! (Lexicon Intelligent Variable Environment) is a proprietary mode designed to transform the way your listening room sounds. LIVE! uses a combination of microphones and digital signal processing (DSP) to enhance the room acoustics and create the illusion of a larger, more reverberant listening space. LIVE! CALIBRATION must be completed before using any of the LIVE! modes.
Setup RV-8 POSITIONING THE MICROPHONES FOR LIVE! Refer to the microphone placement examples below to position the microphones for LIVE! PROPER microphone positioning for LIVE! Position the microphones: 3 On or near opposite side walls 3 Approximately halfway between the front and side speakers 3 At an approximate height between the waist and head of a standing person Rear Left Side Left Rear Right 3 In a location unobstructed by furniture and other fixtures 3 At least 2 feet (0.
Setup Lexicon IMPROPER microphone positioning for LIVE! When positioning the microphones, DO NOT: 7 Place the microphones on the front or rear walls 7 Place the microphones near the floor or ceiling Rear Left 7 Obstruct the microphones with furniture or other fixtures 7 Place the microphones within 2 feet (0.61m) of any speaker Side Left Rear Right The illustration to the right provides an example of improper microphone placement for LIVE! calibration or for a permanent location.
Setup RV-8 PERFORMING LIVE! CALIBRATION MAIN MENU SETUP MODE ADJUST AUDIO CONTROLS TUNER PRESETS SETUP INPUTS SPEAKERS I/O CONFIG DISPLAYS VOLUME CONTROLS TRIGGER TUNER SETUP LOCK OPTIONS LIVE! CALIBRATION POWER MANAGEMENT CUSTOM LIVE! CALIBRATION SETUP !CAUTION! 40 Hz 60 Hz HIGH AUDIO LEVELS 60 Hz Hz 10 SEC YOU WILL 60 HAVE 40 Hz TO LEAVE THE ROOM OR OFF SIT QUIETLY N/A PRESSAPART TO BEGIN COUNTDOWN LIVE! CALIBRATION TEST WILL BEGIN IN 10 LIVE! CALIBRATION IN PROGRESS LIVE! CALIBRATION CALIBRATION
4 Audio Controls Audio Controls ............................................................................
Audio Controls Lexicon AUDIO CONTROLS Selecting AUDIO CONTROLS opens the AUDIO CONTROLS menu, which is used to customize the Main Zone audio output connectors and to control the balance of the Zone 2 and Zone 3 audio output connectors. The BASS, TREBLE, TILT EQ, LOUDNESS, BALANCE and FADER parameters affect the Main Zone audio output connectors, including all Main Zone inputs and listening modes, except the 5.1a BYPASS and 2CH BYPASS listening modes.
Audio Controls RV-8 BASS Parameter Settings The BASS parameter controls the amount of low-frequency boost or cut applied to the Main Zone audio output connectors labeled Front L/R, Center and Sub. TREBLE Parameter Settings The TREBLE parameter controls the amount of high-frequency boost or cut applied to the Main Zone audio output connectors labeled Front L/R and Center.
Audio Controls AUDIO CONTROLS Lexicon (continued) MAIN MENU AUDIO CONTROLS MODE ADJUST AUDIO CONTROLS TUNER PRESETS SETUP BASS TREBLE TILT EQ LOUDNESS BALANCE FADER ZONE2 BALANCE ZONE3 BALANCE TILT EQ AUDIO CONTROLS -3.0 to +3.0dB –3.0dB to +3.0dB TILT EQ Controls the amount of tilt equalization applied to the Main Zone audio output connectors labeled Front L/R, Center and Sub. This parameter setting affects the entire frequency spectrum with a hinge point at 1kHz.
Audio Controls RV-8 TILT EQ Parameter Settings The TILT EQ parameter controls the amount of tilt equalization applied to the Main Zone audio output connectors labeled Front L/R, Center and Sub. LOUDNESS Parameter Settings The LOUDNESS parameter controls the amount of low-frequency boost that is automatically applied to the Main Zone audio output connectors labeled Front L/R, Center and Sub.
Audio Controls Lexicon AUDIO CONTROLS (continued) MAIN MENU AUDIO CONTROLS MODE ADJUST AUDIO CONTROLS TUNER PRESETS SETUP BASS TREBLE TILT EQ LOUDNESS BALANCE FADER ZONE2 BALANCE ZONE2 BALANCE BALANCE AUDIO CONTROLS L< B< BALANCE FADER >R MAIN MENU AUDIO CONTROLS MODE ADJUST AUDIO CONTROLS TUNER PRESETS SETUP BASS TREBLE TILT EQ LOUDNESS BALANCE FADER ZONE2 BALANCE ZONE2 BALANCE >F L< <|> >R BALANCE ZONE2 BALANCE AUDIO CONTROLS Controls the left-to-right balance of the Main Zone audio ou
5 Tuner Presets Tuner Presets ..............................................................................
Tuner Presets Lexicon TUNER PRESETS Selecting TUNER PRESETS from the MAIN MENU displays a list of the pages of existing presets. The preset number, preset name (if available), frequency and broadcast band is displayed. MAIN MENU TUNER PRESETS TUNER PRESETS EDIT PRESET 1 MODE ADJUST AUDIO CONTROLS TUNER PRESETS SETUP PAGE PAGE PAGE PAGE 01 02 03 04 05 06 07 08 09 10 FREQUENCY BAND 1 2 3 4 0.00FM 0.00FM 0.00FM 0.00FM 0.00FM 0.00FM 0.00FM 0.00FM 0.00FM 0.00FM 0.
Tuner Presets RV-8 LISTEN TO PRESET TUNER PRESETS PAGE 1 CLEAR PRESET 01 LISTEN TO PRESET Loads the current preset station. Press the menu arrow to load the station preset. The front panel and on-screen display will display “STATION LOADED.” TUNER PRESETS PAGE 1 01 CLEAR PRESET Clears the current preset entry. The front-panel and on-screen display will display “PRESS MENU TO CLEAR PRESET.” Press the menu arrow to cancel without clearing the preset.
6 Mode Adjust Mode Adjust ...............................................................................6-2 Listening Mode Activation...........................................................6-2 Listening Mode Descriptions .......................................................6-4 Listening Mode Menu Option and Parameter Descriptions........6-39 Mode – Parameter Relationships ...............................................
Mode Adjust MAIN MENU MODE ADJUST AUDIO CONTROLS TUNER PRESETS SETUP * These listening mode names differ depending on the current input source, speaker setup and parameter settings. Refer to the Listening Mode Descriptions for more information. 6-2 Lexicon MODE ADJUST FILM TV MUSIC MUSIC SURR PLIIx + THX* PLIIx MOV* PLIIx MUS* PLII+ THX PLII MOVIE PLII MUSIC PL + THX PRO LOGIC + THX CIN MUSIC NIGHTCLUB CONCERT HHALL CHURCH CATHEDRAL PANORAMA 2-CH SURROUND 2-CHANNEL MONO LOGIC MONO SURROUND MONO 5.
Mode Adjust RV-8 PREFERRED LISTENING MODE SELECTION LISTENING MODE SELECTION BUTTONS The INPUT SETUP menus include four preferred listening mode selection parameters labeled 2-CH, DOLBY D, DTS(-ES), 5.1a and MIC. These parameters are used to select a preferred listening mode for 2-channel, Dolby Digital, DTS(-ES), 5.1a and LIVE! input sources. The RV-8 automatically activates the selected listening mode whenever a new input is selected or a new input source is present.
Mode Adjust Lexicon LISTENING MODE DESCRIPTIONS Each listening mode description lists the default and possible settings for each listening mode menu parameter. All listening mode menus are shown in the Appendix. Listening mode menu option and parameter descriptions begin on page 6-39. L7 FILM MODE ADJUST L7 TV FILM MODE ADJUST TV This listening mode is designed for enhanced playback of 2-channel stereo or matrix-encoded film sources.
Mode Adjust RV-8 L7 MUSIC MODE ADJUST L7 MUSIC SURR MODE ADJUST MUSIC This listening mode is designed for playback of 2-channel stereo or matrix-encoded music sources. Logic 7 MUSIC is a proprietary Lexicon listening mode based on the Logic 7 FILM listening mode, but specifically tailored for music sources. Parameter Default Setting Possible Settings VOCAL ENHANCE +0.0dB +6.0dB, +3.0dB, +0.
Mode Adjust Lexicon DOLBY PLIIx + THX & DOLBY PLII + THX MODE ADJUST PLIIX + OR MODE ADJUST PLII + Dolby Pro Logic IIx technology is an extension to Dolby Pro Logic II that enables the listener to experience natural and seamless 6.1- or 7.1-channel (six or seven speakers and a subwoofer) surround sound from any native two-channel (stereo) or 5.1-channel source.
Mode Adjust RV-8 DOLBY PLIIx MOV & DOLBY PLII MOVIE MODE ADJUST PLIIx MOVIE OR MODE ADJUST PLII MOVIE Dolby Pro Logic IIx technology is an extension to Dolby Pro Logic II that enables the listener to experience natural and seamless 6.1- or 7.1-channel (six or seven speakers and a subwoofer) surround sound from any native two-channel (stereo) or 5.1-channel source.
Mode Adjust Lexicon DOLBY PLIIx MUS & DOLBY PLII MUSIC MODE ADJUST PLIIx MUS OR MODE ADJUST PLII MUSIC Dolby Pro Logic IIx technology is an extension to Dolby Pro Logic II that enables the listener to experience natural and seamless 6.1- or 7.1-channel (six or seven speakers and a subwoofer) surround sound from any native two-channel (stereo) or 5.1-channel source. The PLIIx listening mode is only available when the front, side and rear speakers are present.
Mode Adjust RV-8 DOLBY PL + THX MODE ADJUST DOLBY PRO LOGIC PL + MODE ADJUST This mode is designed for playback of Dolby Surround-encoded sources and decodes four channels: three front channels and one mono surround channel with a high-frequency rolloff above 7kHz. This mode is recommended for home theaters with THX-certified speakers. Dolby PL + THX mode: • • Applies THX re-equalization to simulate high-frequency rolloffs that occur in movie theaters.
Mode Adjust Lexicon DTS NEO:6 + THX MODE ADJUST DTS NEO:6 CIN & DTS NEO:6 MUSIC + MODE ADJUST This mode is designed for playback of matrix-encoded digital stereo film sources. DTS Neo:6 derives six channels when both side and rear speakers are present (rear channels will be in parallel). It derives five channels when only side or rear speakers are present. In addition to THX processing, THX re-equalization is applied to simulate high-frequency rolloffs that occur in movie theaters.
Mode Adjust RV-8 NIGHTCLUB CONCERT HALL MODE ADJUST MODE ADJUST NIGHTCLUB The NIGHTCLUB mode is designed for playback of “dry” music sources that benefit from the addition of room reflections, especially music sources that lack ambience in the recording. The NIGHTCLUB mode generates early reflections and sends them to the front, side and rear channels to simulate small, intimate listening spaces.
Mode Adjust Lexicon CHURCH MODE ADJUST CATHEDRAL MODE ADJUST CHURCH CATHEDRAL The CHURCH mode uses a reverb algorithm to emphasize the rich, smooth, reverberant decay characteristic of small and medium listening spaces – such as churches and chambers – with long reverberation time relative to their sizes. The CATHEDRAL mode is similar to the CHURCH listening mode.
Mode Adjust RV-8 PANORAMA MODE ADJUST PANORAMA CALIBRATION PANORAMA MODE ADJUST The PANORAMA mode is designed for playback of stereo and matrix-encoded sources. PANORAMA uses proprietary Lexicon algorithms to move the stereo image outward from the front speakers, producing a wider stereo field with greater depth. Sound quality depends on proper location of the listening position and front speakers.
Mode Adjust Lexicon LEFT CENTER RIGHT To calibrate the PANORAMA listening mode: 1. Remove all obstructions between the speakers and the primary listening position. 2. Make sure the distances between the speakers and the primary listening position are properly measured. To do this, select one of the following options. • Select the AUTO SPEAKER SETUP menu DISTANCES option to have the RV-8 automatically calibrate speaker distances.
Mode Adjust RV-8 2-CH SURROUND MONO LOGIC MODE ADJUST MODE ADJUST 2-CH SURROUND MONO LOGIC This mode, designed for playback of stereo sources, sends the left channel to Front, Side and Rear Left channels and the right channel to Front, Side and Rear Right channels, and sums the Left and Right for the center. It is recommended for background music. This mode, designed for playback of mono sources, uses proprietary Lexicon reverb algorithms to realistically expand mono sources to use all channels.
Mode Adjust Lexicon MONO SURROUND MODE ADJUST 5.1 L7 FILM MONO SURROUND MODE ADJUST This mode, designed for playback of mono sources, sends the mono source to all channels. Parameter OUTPUT LEVELS Refer to page 6-37 CUSTOM Refer to page 6-37 MONO MODE ADJUST MONO This mode, designed for playback of mono sources, sends mono sources to the center channel and subwoofer. 5.1 FILM The 5.1 L7 FILM mode is a proprietary Lexicon listening mode designed for playback of 5.
Mode Adjust RV-8 5.1 L7 TV MODE ADJUST 5.1 L7 MUSIC 5.1 MODE ADJUST TV 5.1 MUSIC This proprietary Lexicon listening mode is designed for playback of 5.1-channel Dolby Digital-encoded broadcast sources. Based on the 5.1 L7 FILM listening mode, 5.1 L7 TV derives seven channels from 5.1-channel input sources with enhanced front steering. This proprietary Lexicon listening mode is designed for playback of 5.1-channel Dolby Digital-encoded music sources. Based on the 5.1 L7 FILM listening mode, 5.
Mode Adjust Lexicon THX, THX UL2Cin & THX SurEX MODE ADJUST OR UL2Cin OR SurEX These modes are designed for 7-channel playback of 5.1-channel Dolby Digital film sources that do not have THX Surround EX encoding. They apply THX re-equalization to simulate high-frequency rolloffs that occur in movie theaters. Most films are mixed for movie theaters, and might sound too bright when played back in home theaters without re-equalization.
Mode Adjust RV-8 • ASA processing is applied to signals sent to the rear speakers. Refer to the ASA parameter description on page 3-31 for more information. When THX Surround EX decoding is active: Matrix decoding is applied to derive three surround channels from 5.1-channel Dolby Digital sources. THX MUSIC MODE ADJUST MUSIC This listening mode is designed for playback of 5.1-channel Dolby Digital music sources, and cannot be activated unless side and rear speakers are present.
Mode Adjust Lexicon 5.1 PLIIx MOV MODE ADJUST 5.1 PLIIx MOV The 5.1 PLIIx MOV (MOVIE) listening mode is designed to play back 7.1 discrete channels decoded from 5.1-channel Dolby Digital film sources. The seven main channels are full-frequency. The .1 channel, often referred to as LFE information, has a limited frequency range of up to 120Hz. Note: The 5.1 PLIIx MOV listening mode is only available when the front, side and rear speakers are present.
Mode Adjust RV-8 5.1 PLIIx MUS MODE ADJUST 5.1 PLIIx MUS The 5.1 PLIIx MUS (MUSIC) listening mode is designed to playback 7.1 discrete channels decoded from 5.1-channel Dolby Digital music sources. The seven main channels are full–frequency. The .1 channel, often referred to as LFE information, has a limited frequency range of up to 120Hz. Note: The RV-8 cannot detect Dolby Digital Surround EX encoding in non-flagged 5.1-channel Dolby Digital input sources. Activating the 5.
Mode Adjust Lexicon DOLBY DIGITAL & DOLBY DIGITAL EX MODE ADJUST DIGITAL OR DIGITAL EX These listening modes are designed to decode and play back 5.1 discrete channels from 5.1-channel Dolby Digital sources. The five main channels are full-frequency. The .1 channel, often referred to as LFE information, has a limited frequency range of 120Hz. The mode name differs, depending on the encoding present in the input source, the EX DECODING parameter setting and the speaker setup.
Mode Adjust RV-8 5.1 2-CHANNEL MODE ADJUST 5.1 MONO LOGIC 5.1 2-CHANNEL MODE ADJUST This mode, recommended for recording purposes, is designed for converting 5.1-channel Dolby Digital-encoded input sources into 2-channel Logic 7-encoded output signals. The downmixed 5.1-channel Dolby Digital input signals are sent to the Front L/R speakers and subwoofer. 5.
Mode Adjust Lexicon 5.1 MONO SURR MODE ADJUST 5.1 MONO MODE ADJUST 5.1 MONO SURR This listening mode, designed for playback of Dolby Digital-encoded mono sources, sends mono signals to all channels. 5.1 MONO This listening mode, designed for playback of Dolby Digital-encoded mono sources, sends mono signals to the center channel and subwoofer.
Mode Adjust RV-8 DTS-ES DECODING The DTS, DTS-ES, and DTS-ES Discr listening modes are designed for, at a minimum, playback of 5.1-channel DTS, 5.1-channel matrix-encoded DTS-ES and 6.1-channel discrete-encoded DTS-ES sources. The DTS, DTS-ES, and DTS-ES Discr listening mode names differ depending on the encoding present in the input source, the DECODING parameter setting and the speaker setup. DTS-ES listening modes are available when DTS-ES decoding is activated.
Mode Adjust Lexicon DTS-ES L7 FILM & DTS L7 FILM MODE ADJUST FILM OR DTS-ES L7 MUSIC & DTS L7 MUSIC MODE ADJUST FILM MUSIC OR MUSIC These proprietary Lexicon listening modes use an advanced matrix to decode seven channels from 5.1- and 6.1-channel film sources with enhanced front steering. When both side and rear speakers are present, the DTS-ES L7 FILM listening mode also increases the perceived length and sense of envelopment of the listening space.
Mode Adjust RV-8 DTS-ES THX & DTS THX UL2Cin MODE ADJUST OR UL2Cin The DTS THX UL2Cin (ULTRA2 CINEMA) and DTS-ES THX listening modes allow 7-channel playback of 5.1-channel DTS sources that lack DTS-ES encoding. They are designed for playback of 5.1-channel DTS, 5.1-channel matrix-encoded DTS-ES, or 6.1-channel DTS-ES discrete-encoded film sources. DTS THX UL2Cin and DTS-ES THX are recommended for home theaters with THX-certified speakers.
Mode Adjust Lexicon DTS-ES THX & DTS THX UL2CIN (continued) Input Source Parameter Setting 5.1-Channel DTS 5.1-Channel Matrix-Encoded DTS-ES 6.
Mode Adjust RV-8 DTS 2-CHAN & DTS-ES 2-CHAN MODE ADJUST 2-CHAN OR 5.1a L7 FILM 2-CHAN MODE ADJUST These modes, recommended for recording purposes, send downmixed 5.1-channel or 6.1-channel DTS-ES input signals to the front speakers and subwoofer as 2-channel Logic 7-encoded output signals. 5.1 FILM The 5.1a LOGIC7 FILM listening mode is a proprietary Lexicon listening mode that uses LOGIC7 decoding to derive seven channels from 5.1-channel analog film sources with enhanced front steering.
Mode Adjust Lexicon 5.1a L7 MUSIC MODE ADJUST 5.1a 5.1a THX UL2Cin, 5.1a THX SurEX & 5.1a THX MUSIC MODE ADJUST The 5.1a LOGIC7 MUSIC listening mode is similar to the 5.1a LOGIC7 FILM listening mode, but specifically tailored for music sources. This mode is designed and recommended for playback of 5.1-channel analog music sources. Option/Parameter Default Setting Possible Settings VOCAL ENHANCE +0.0dB +6.0dB, +3.0dB, +0.
Mode Adjust RV-8 Input Source 5.1-Channel Analog 5.1-Channel THX Surround EX Analog (Flagged) 5.1-Channel THX Surround EX Analog (Non-Flagged) SURROUND EX: ON 5.1a THX SurEX 5.1a THX SurEX 5.1a THX SurEX SURROUND EX: OFF 5.1a THX ULTRA2 5.1a THX ULTRA2 5.1a THX ULTRA2 Parameter Setting The 5.1a THX UL2Cin listening mode The 5.1a THX UL2Cin listening mode is available when both side and rear speakers are present and THX Ultra2 decoding is active.
Mode Adjust Lexicon 5.1a THX MUSIC MODE ADJUST 5.1a 5.1a STANDARD MODE ADJUST MUSIC The 5.1a THX MUSIC listening mode is designed for playback of 5.1-channel analog music sources. It cannot be activated unless side and rear speakers are present. This mode performs best in home theaters where the rear speaker are placed close together. ASA processing is applied to signals sent to the rear speakers. Refer to the ASA parameter description on page 3-35 for more information. 5.
Mode Adjust RV-8 5.1a 2-CHANNEL MODE ADJUST 5.1a BYPASS 5.1a 2-CHANNEL MODE ADJUST This mode downmixes 5.1-channel analog input signals into 2-channel LOGIC7-encoded output signals. It sends these signals to the front speakers and the subwoofer. It is recommended for recording purposes, particularly for recording from a DVD-A or multi-channel SACD player to a CD-R or another 2-channel recording format.
Mode Adjust 2CH BYPASS MODE ADJUST 2CH BYPASS This listening mode sends 2-channel analog audio input signals to the Main Zone audio output connectors labeled Front L/R with no internal processing. The 2CH BYPASS listening mode is automatically activated whenever a 2-channel analog source is present and the MAIN ADV menu ANALOG BYPASS parameter is set to ON. The 2CH BYPASS listening mode is not available when a digital source is present and the MAIN ADV menu INPUT SELECT parameter is set to AUTO.
Mode Adjust RV-8 HEADPHONE DTS MODE ADJUST HEADPHONE HEADPHONE DTS is a proprietary Lexicon listening mode designed for enhanced playback of DTS(-ES)-encoded music or film sources through headphones. This listening mode uses LOGIC7 processing and Head Related Transfer Functions to realistically increase the perceived sense of envelopment when listening through headphones. The HEADPHONE DTS listening mode is recommended for DTSencoded sources when listening through headphones.
Mode Adjust Lexicon LIVE! MED parameter settings: LIVE! LARGE parameter settings: Parameter Default Setting Possible Settings MID RT 1.84s 115ms to 15.4s BASS RT 2.76s 23ms to 30.8ms ROLLOFF 2.4kHz 500Hz to 20kHz TREB CUT RT 3.1kHz 500Hz to 20kHz PRE-DELAY 18ms 10ms to 100ms ADVANCED CUSTOM Parameter Default Setting Possible Settings MID RT 4.71s 115ms to 30.8s BASS RT 4.71s 23ms to 30.8ms ROLLOFF 3.1kHz 500Hz to 20kHz TREB CUT RT 2.
Mode Adjust RV-8 OUTPUT LEVELS MODE ADJUST OUTPUT LEVELS CENTER SIDE L/R REAR L/R SUB CUSTOM VS PRESET Listening Mode +0dB +0dB +0dB +0dB OUTPUT LEVELS MODE ADJUST Opens the OUTPUT LEVELS menu, which is used to adjust output levels for the Main Zone audio output connectors labeled Center, Subwoofer, Side L/R and Rear L/R. The OUTPUT LEVELS option does not appear on listening mode menus when the selected listening mode does not accommodate multichannel output signals.
Mode Adjust Lexicon RESET MODE MODE ADJUST (Listening Mode) CUSTOM RESET MODE Restores the factory-default version of the selected listening mode, restoring all listening mode menu parameters to their factory default settings. 2. Press the arrow button to restore the factory-default version of the selected listening mode. Press the arrow button to close the message without restoring the factory-default. To restore the factory-default version of the selected listening mode: Note: 1.
Mode Adjust RV-8 LISTENING MODE MENU OPTION and PARAMETER DESCRIPTIONS 5 SPKR ENHANCE ON, OFF Simulates 7-channel playback in 5-channel speaker configurations. When set to ON, the RV-8 provides an increased sense of spaciousness and envelopment through the surround speakers. This enhancement is most noticeable when the surround speakers are positioned to the side of the primary listening position, or when the primary listening position is located against the rear wall.
Mode Adjust Lexicon LISTENING MODE MENU OPTION and PARAMETER DESCRIPTIONS CENTER OFF, –30 to +12dB Controls the output level of the audio output connector labeled Center. Available in all except 2 CH modes (2-CHANNEL, 2 CH BYPASS, DTS(-ES) 2-CHAN, 5.1 2-CHANNEL), MONO, 5.1 MONO and LIVE! modes. CENTER DEPTH 0 to 18 Adjusts the amount of processing applied to the center channel, changing the perceived distance of the center speaker.
Mode Adjust RV-8 EARLY RFLX LVL –80dB to +12dB, OFF Controls the amount of additional early reflections. Available in all LIVE! modes. This parameter is available in all DTS modes. EFFECT LVL EX DECODING –12 to +6dB Adjusts the amount of effect applied to the listening mode. Available in NIGHTCLUB, CONCERT HALL, CHURCH, CATHEDRAL, PANORAMA, MONO LOGIC and 5.1 MONO LOGIC modes. ES DECODING AUTO, ON, OFF Controls DTS-ES decoding, which extracts a rear channel from 5.1-channel DTS, 5.
Mode Adjust Lexicon LISTENING MODE MENU OPTION and PARAMETER DESCRIPTIONS • This parameter is available in 5.1 PLIIx MOV, 5.1 PLIIx MUS, DOLBY DIGITAL EX and DOLBY DIGITAL modes. • When the Shift command bank is activated, pressing the remote control DOLBY button while a 5.1-channel Dolby Digital source is present activates the Dolby DIGITAL EX or Dolby DIGITAL listening mode. Subsequent presses adjust the EX DECODING parameter, cycling through the AUTO, ON and OFF settings.
Mode Adjust RV-8 MASTER LEVEL –5 to +5dB Adjusts the output level of 2-channel Logic 7-encoded sources. Available in 5.1 2-CHANNEL and DTS(-ES) 2-CHAN modes. MID RT 24ms to 24.3s Works with the SIZE parameters to adjust the amount of time required for mid-frequency information to decay below 60dB in level. The full parameter range might not be available depending on the SIZE parameter setting. Available in CHURCH, CATHEDRAL and all LIVE! modes.
Mode Adjust Lexicon LISTENING MODE MENU OPTION and PARAMETER DESCRIPTIONS REAR L/R –30 to +12dB, OFF Controls the output level of the Main Zone audio output connector labeled Rear L/R. Available in all except 2-CHANNEL, MONO, 5.1 2-CHANNEL, 5.1 MONO, DTS (-ES) 2-CHAN, 2CH BYPASS and LIVE! modes. (continued) SIDE L/R Controls the level of the Side L/R audio output connectors in the Main Zone. Available in all except 2-CHANNEL, MONO, 5.1 2-CHANNEL, 5.
Mode Adjust RV-8 SOURCE RIGHT, LEFT & RIGHT, LEFT Controls the perceived direction of the PANORAMA listening mode external calibration source signal. When RIGHT is selected, the sound is perceived to come from the right of the primary listening position. When LEFT is selected, the sound is perceived to come from the left of the primary listening position. When LEFT & RIGHT is selected, the sound is perceived to come from all around the primary listening position.
Mode Adjust Lexicon LISTENING MODE MENU OPTION and PARAMETER DESCRIPTIONS When AUTO is selected, THX Surround EX decoding is engaged when a flagged 5.1-channel Dolby Digital source with THX Surround EX encoding is detected. THX Surround EX decoding is not engaged when a non-flagged 5.1-channel Dolby Digital source with or without THX Surround EX encoding is detected. LISTENING MODE MENU OPTION and PARAMETER DESCRIPTIONS (continued) not engaged when a non-flagged 5.
Mode Adjust RV-8 MODE – PARAMETER RELATIONSHIPS The following table lists each parameter and the modes in which it is used. The parameter... Is used in these modes 5 SPKR ENHANCE All L7 modes ACADEMY FILTER MONO LOGIC and 5.1 MONO LOGIC AUTO AZIMUTH L7 FILM and L7 TV BASS CONTENT PANORAMA BASS ENHANCE All L7 modes BASS RT CHURCH, CATHEDRAL and all LIVE! modes CALIBRATION PANORAMA CENTER All except 2 CH modes (2-CHANNEL, 2 CH BYPASS, DTS(-ES) 2-CHAN, 5.1 2-CHANNEL, MONO, 5.
Mode Adjust Lexicon MODE-PARAMETER RELATIONSHIPS (continued) The parameter... Is used in these modes EX DECODING 5.1 PLIIx MOV, 5.1 PLIIx MUS, DOLBY DIGITAL EX and DOLBY DIGITAL FRONT STEERING L7 TV, L7 MUSIC, L7 MUSIC SURR, all 5.1 L7 modes and all DTS L7 modes INPUT BALANCE PANORAMA LFE MIX All Dolby Digital modes except MONO modes (5.1 MONO LOGIC, 5.1 MONO SURR, 5.1 MONO), all DTS modes and 5.
Mode Adjust RV-8 The parameter... Is used in these modes SIZE NIGHTCLUB, CONCERT HALL, CHURCH, CATHEDRAL and all LIVE! modes SOUND STAGE All L7 modes SOURCE PANORAMA CALIBRATION SPEAKER ANGLE PANORAMA CALIBRATION SPEECH DETECT NIGHTCLUB, CONCERT HALL, CHURCH and CATHEDRAL SPREAD All LIVE! modes SUB & SUB LVL All except LIVE! modes SURR ROLLOFF All L7 modes SURROUND DLY Dolby PLII MUSIC and Dolby PLIIx MUSIC SURROUND EX THX ULTRA2, THX SurEX, THX SURROUND MIX 5.
7 Troubleshooting and Maintenance Troubleshooting..........................................................................7-2 Routine Maintenance ..................................................................7-4 Restoring Factory-Default Settings...............................................
Troubleshooting and Maintenance Lexicon TROUBLESHOOTING The RV-8 does not power on. 1. Make sure the rear-panel power switch is set to the | (“on”) position. 2. Attempt to power on the RV-8 with the front-panel Standby button and remote control On button. 3. Examine the power cord to ensure a good connection between the rear-panel AC input connector and the wall outlet. front-panel displays when audio has been muted. To deactivate mute, press the Mute button or adjust the volume level. 3.
Troubleshooting and Maintenance RV-8 2. Check the INPUT SETUP menu VIDEO IN and COMPONENT IN (page 3-11) parameters to ensure the appropriate video connector is assigned to the selected input. RF interference is present in the audio or video. 1. Make sure the RV-8 is not positioned near unshielded TV or FM antennas, cable TV decoders and other RF-emitting devices. 2. Contact an authorized Lexicon dealer. 3. Contact Lexicon customer service at 781-280-0300 or www.lexicon.com.
Troubleshooting and Maintenance Lexicon ROUTINE MAINTENANCE low-pressure blower can be used to remove dust from its exterior surface. The bulleted items below describe routine maintenance that should be performed on a periodic basis. • Clean the RV-8 exterior surface with a soft, lint-free cloth. Do not use alcohol, benzene, acetone-based cleaners or strong commercial cleaners. Do not use a cloth made with steel wool or metal polish.
A Appendix Specifications ............................................................................ A-2 Declaration of Conformity .........................................................
Appendix A Lexicon SPECIFICATIONS Main Zone Audio Performance Input Sensitivity 200mV Rms (2V Rms for maximum output level) at 0dB input gain Input Impedance 100kΩ in parallel with 150pF Audio Input & Output Connectors Analog Audio Inputs Eight stereo (RCA) or five stereo and one 5.1-channel or 2 stereo and two 5.
Appendix A RV-8 Composite & S-Video Performance FM Tuner Performance Compatibility NTSC, PAL and SECAM Selectivity >87dBmV, 93dBmV typical Switching Active Frequency Response 50Hz to 16kHz, +0.1dB/-1.0dB Output Level <0.4% at 1 kHz (stereo) 1.0V peak-to-peak THD + Noise Impedance 75Ω Signal-to-Noise Ratio 50dB minimum at 60dBmV Input Return Loss >40dB Image Rejection >50dB, >60dB typical Differential Gain <0.5% AM Suppression >45dB, >55dB typical Differential Phase <0.
Appendix A Lexicon Other Power Requirements 120-230 VAC, 50-60Hz, 60W (universal line input), detachable power cord RV-8 Dimensions & Weight • • • • Rack-Mounting • Optional brackets are available for installation in a standard 19" equipment rack (two rack units required) Environment • Operating temperature: 0° to 35°C (32° to 95°F) • Storage temperature: –30° to 75°C (–22° to 167°F) • Relative humidity: 95% maximum without condensation Remote Control Height (with feet): 7.76 inches (197.
B Appendix Menu Tree ..................................................................................
Appendix B Lexicon MENU TREE TRIGGER SETUP MAIN MENU SETUP MODE ADJUST AUDIO CONTROLS TUNER PRESETS SETUP INPUTS SPEAKERS I/O CONFIG DISPLAYS VOLUME CONTROLS TRIGGER TUNER SETUP LOCK OPTIONS LIVE! CALIBRATION POWER MANAGEMENT INPUT SETUP I/O CONFIG TUNER SETUP DVD1 DVD2 SAT VCR TV CD TUNER PHONO ANALOG INPUTS AMP OUTPUTS REGION USA SCAN SENS LOW AUTOLOAD CLEAR ALL TUNER PRESETS DISPLAY RDS NAME RADIO TEXT ON SCROLL RATE MEDIUM AUTO FREQUENCY ON continued on page B-6 SPEAKER SETUP SETUP CROSSOV
Appendix B RV-8 SETUP MENU: INPUTS MAIN MENU SETUP INPUT SETUP MODE ADJUST AUDIO CONTROLS TUNER PRESETS SETUP INPUTS SPEAKERS I/O CONFIG DISPLAYS VOLUME CONTROLS TRIGGER TUNER SETUP LOCK OPTIONS LIVE! CALIBRATION POWER MANAGEMENT DVD1 DVD2 SAT VCR TV CD TUNER PHONO Selecting SETUP INPUTS prompts the selection of the desired input (for example, DVD1). Selecting an input opens the corresponding INPUT SETUP menu shown below.
Appendix B Lexicon SETUP MENU: INPUTS (continued) MAIN MENU SETUP INPUT SETUP MODE ADJUST AUDIO CONTROLS TUNER PRESETS SETUP INPUTS SPEAKERS I/O CONFIG DISPLAYS VOLUME CONTROLS TRIGGER TUNER SETUP LOCK OPTIONS LIVE! CALIBRATION POWER MANAGEMENT DVD1 DVD2 SAT VCR TV CD TUNER PHONO DIGITAL ANLG DMIX DVD1 INPUT SETUP NAME DVD1 DIGITAL IN COAX-1 ANALOG IN NONE ANLG IN LVL AUTO VIDEO IN S-VIDEO-1 COMPONENT IN 1 2-CH FILM D 5.1 FILM FILM 5.1a 5.
Appendix B RV-8 SETUP MENU: SPEAKERS MAIN MENU SETUP SPEAKER SETUP MODE ADJUST AUDIO CONTROLS TUNER PRESETS SETUP INPUTS SPEAKERS I/O CONFIG DISPLAYS VOLUME CONTROLS TRIGGER TUNER SETUP LOCK OPTIONS LIVE! CALIBRATION POWER MANAGEMENT SET CROSSOVERS CHECK MICROPHONES AUTOMATIC MANUAL CUSTOM CROSSOVER SETUP SETUP CUSTOM SETUP THX SETUP R SET CROSSOVERS BEFORE CALIBRATING 80Hz C 80Hz M SUB 80Hz L 80Hz SL RL 80Hz 80Hz THX SPEAKER SETUP CUSTOM SETUP 80 Hz FRONT L/R 80 Hz CENTER 80 Hz SIDE L/R 80
Appendix B Lexicon SETUP MENU: SPEAKERS (continued) MAIN MENU SETUP SPEAKER SETUP CHECK MICROPHONES CHECK MICROPHONES CHECK MICROPHONES MODE ADJUST AUDIO CONTROLS TUNER PRESETS SETUP INPUTS SPEAKERS I/O CONFIG DISPLAYS VOLUME CONTROLS TRIGGER TUNER SETUP LOCK OPTIONS LIVE! CALIBRATION POWER MANAGEMENT SET CROSSOVERS CHECK MICROPHONES AUTOMATIC MANUAL GROUP MICROPHONES INTO A BUNDLE IN THE MIDDLE OF THE ROOM CHECKING FOR SILENCE CHECKING MICROPHONES AUTO SPEAKER SETUP DISTANCES & LEVELS DISTAN
Appendix B RV-8 MAIN MENU SETUP SPEAKER SETUP AUTO SPEAKER SETUP MODE ADJUST AUDIO CONTROLS TUNER PRESETS SETUP INPUTS SPEAKERS I/O CONFIG DISPLAYS VOLUME CONTROLS TRIGGER TUNER SETUP LOCK OPTIONS LIVE! CALIBRATION POWER MANAGEMENT SET CROSSOVERS CHECK MICROPHONES AUTOMATIC MANUAL DISTANCES & LEVELS DISTANCES OUTPUT LEVELS SETTING SETUP DISTANCES CUSTOM FRONT LEFT CENTER FRONT RIGHT SIDE RIGHT REAR RIGHT REAR LEFT SIDE LEFT SUBWOOFER SETTING SETUP LEVELS CUSTOM 0.0ft 0.0ft 0.0ft 0.0ft 0.0ft 0.
Appendix B Lexicon SETUP MENU: SPEAKERS (continued) MAIN MENU SETUP SPEAKER SETUP AUTO SPEAKER SETUP MODE ADJUST AUDIO CONTROLS TUNER PRESETS SETUP INPUTS SPEAKERS I/O CONFIG DISPLAYS VOLUME CONTROLS TRIGGER TUNER SETUP LOCK OPTIONS LIVE! CALIBRATION POWER MANAGEMENT SET CROSSOVERS CHECK MICROPHONES AUTOMATIC MANUAL DISTANCES & LEVELS DISTANCES OUTPUT LEVELS SETTING SETUP DISTANCES CUSTOM 0.0ft 0.0ft 0.0ft 0.0ft 0.0ft 0.0ft 0.0ft 0.
Appendix B RV-8 MAIN MENU SETUP SPEAKER SETUP MANUAL SPEAKER SETUP LEVELS CALIBRATION MODE ADJUST AUDIO CONTROLS TUNER PRESETS SETUP INPUTS SPEAKERS I/O CONFIG DISPLAYS VOLUME CONTROLS TRIGGER TUNER SETUP LOCK OPTIONS LIVE! CALIBRATION POWER MANAGEMENT SET CROSSOVERS CHECK MICROPHONES AUTOMATIC MANUAL SPEAKER DISTANCES LEVELS CALIBRATION INTERNAL NOISE TEST EXTERNAL NOISE TEST BASS PEAK LIMITER R SET CROSSOVERS BEFORE CALIBRATING SR RR 60Hz 60Hz 40Hz C 60Hz M SUB 40Hz L 40Hz SL RL 60Hz 6
Appendix B Lexicon SETUP MENU: I/O CONFIG MAIN MENU SETUP I/O CONFIG REAR PANEL CONFIG MODE ADJUST AUDIO CONTROLS TUNER PRESETS SETUP INPUTS SPEAKERS I/O CONFIG DISPLAYS VOLUME CONTROLS TRIGGER TUNER SETUP LOCK OPTIONS LIVE! CALIBRATION POWER MANAGEMENT ANALOG INPUTS AMP OUTPUTS 8 STEREO INPUTS OR 5 ST. & (1) 5.1 ANLG OR 2 ST. & (2) 5.1 ANLG AMP OUTPUTS MAIN 7.1 MAIN 5.1 & ZONE2 2.0 MAIN 5.1 & ZONE3 2.0 8 STEREO INPUTS FOR REAR PANEL CFG 2 ST. & (2) 5.1 ANLG FOR REAR PANEL CFG 5 ST. & (1) 5.
Appendix B RV-8 SETUP MENU: TUNER SETUP MAIN MENU SETUP TUNER SETUP MODE ADJUST AUDIO CONTROLS TUNER PRESETS SETUP INPUTS SPEAKERS I/O CONFIG DISPLAYS VOLUME CONTROLS TRIGGER TUNER SETUP LOCK OPTIONS LIVE! CALIBRATION POWER MANAGEMENT REGION USA SCAN SENS LOW AUTOLOAD CLEAR ALL TUNER PRESETS DISPLAY RDS NAME RADIO TEXT ON SCROLL RATE MEDIUM AUTO FREQUENCY ON PRESS RIGHT J TO START AUTOLOAD PRESS RIGHT J TO CLEAR ALL PRESETS PAGE 1 PAGE 2 PAGE 3 PAGE 4 FAST MEDIUM SLOW USA EUROPE JAPAN E.
Appendix B Lexicon MAIN MENU: TUNER PRESETS MAIN MENU TUNER PRESETS TUNER PRESETS MODE ADJUST AUDIO CONTROLS TUNER PRESETS SETUP PAGE 1 PAGE 2 PAGE 3 PAGE 4 01 02 03 04 05 06 07 08 09 10 EDIT PRESET 1 0.00FM 0.00FM 0.00FM 0.00FM 0.00FM 0.00FM 0.00FM 0.00FM 0.00FM 0.00FM Each tuner preset page allows up to 10 preset stations. FREQUENCY BAND 0.
Appendix B RV-8 MAIN MENU: MODE ADJUST MAIN MENU MODE ADJUST AUDIO CONTROLS TUNER PRESETS SETUP * These listening mode names differ depending on the current input source, speaker setup and parameter settings. Refer to the Listening Mode Descriptions for more information. MODE ADJUST FILM TV MUSIC MUSIC SURR PLIIx + * PLIIx MOV* PLIIx MUS* PLII+ PLII MOVIE PLII MUSIC PL + PRO LOGIC + CIN MUSIC NIGHTCLUB CONCERT HHALL CHURCH CATHEDRAL PANORAMA 2-CH SURROUND 2-CHANNEL MONO LOGIC MONO SURROUND MONO 5.
Appendix B Lexicon MAIN MENU: MODE ADJUST 5.1 FILM VOCAL ENHANCE RE-EQUALIZER SOUND STAGE 5 SPKR ENHANCE BASS ENHANCE SURR ROLLOFF REAR DLY OFFSET COMPRESSION LFE MIX OUTPUT LEVELS CUSTOM 5.1 TV VOCAL ENHANCE FRONT STEERING RE-EQUALIZER SOUND STAGE 5 SPKR ENHANCE BASS ENHANCE SURR ROLLOFF REAR DLY OFFSET COMPRESSION LFE MIX OUTPUT LEVELS CUSTOM 5.1 +0.0dB ON REAR ON OFF 7.0kHz 15ms OFF +0.0dB +0.0dB FILM OFF REAR ON OFF 7.0kHz 15ms OFF +0.0dB MUSIC B-14 OFF +0.0dB 5.
Appendix B RV-8 Selecting the listening mode menu CALIBRATION, OUTPUT LEVELS or CUSTOM option opens the corresponding menu path shown below. The CALIBRATION option is available for the PANORAMA listening mode. The OUTPUT LEVELS and CUSTOM options are available for most listening modes. These menus are identical regardless of which listening mode is selected. Listening mode menu parameter drop-down menus are shown below and on the next page.
Appendix B Lexicon MAIN MENU: MODE ADJUST INPUT BALANCE L< MASTER LEVEL LFE MIX MID RT -20.0 or -10.0 to +0.0dB CENTER MIX -127 +0 +127 24ms to 48.6s ON OFF PRE-DELAY 30ms to 20.2s LOW FREQ WIDTH -25 to +25 REAR DLY OFFSET OFF, 1 to 30ms REAR L/R PANORAMA LIVENESS B-16 -5 to +5dB >R (continued) 10 to 100ms RE-EQUALIZER ON OFF OFF, -30 to 12dB RESET MODE PRESS RIGHT TO RESTORE MODE ROLLOFF 500Hz to 20.
Appendix B RV-8 MAIN MENU: RESTORE DEFAULTS FACTORY SETTINGS Refer to the Restoring Factory-Default Settings section that begins on page 7-4 for more information.
C Appendix Remote Control Programming .................................................. C-2 Three-Digit Preprogrammed Codes .........................................
Appendix C Lexicon REMOTE CONTROL PROGRAMMING The RV-8 remote control has been designed to provide a new standard in remote control technology offering a very powerful and flexible preprogrammed and learning product. The RV-8 remote control can operate up to 10 home entertainment and home automation components by using the preprogrammed code library in the remote control, by teaching up to 530 commands into the RV-8 remote from your original remote controls, or a combination of both.
Appendix C RV-8 MACRO OPERATIONS A “macro” is a series of commands that can be sent out with the push of a single button. Any function available on an original remote control or in the preprogrammed database can be added to a macro to completely automate what would normally be done by pushing buttons one at a time. A macro can be configured to power on a TV or projector, RV-8, and RT-10 Disc Player, change to the appropriate inputs and outputs, dim lights and start a movie.
Appendix C Lexicon REMOTE PROGRAMMING OVERVIEW The first task is to get all original remote controls together. You may have one or more components that do not have original remote c o n t r o l s . T h e s e c a n s t i l l b e c o n t r o l l e d b y t h e R V- 8 . T h e preprogrammed method must be used for those devices.
Appendix C RV-8 USING PREPROGRAMMED CODES Note: To program the remote to make it compatible with other components: When using the Preprogramming method, always use the appropriate button as shown in the column when asked ”FROM TABLE.” The labels of the buttons may have been changed, but the codes are in the positons as shown to the left. For example, the AUDIO Code table will always be the top left button. The CD Code table will always be the fourth button down on the right side of the LCD screen, etc.
Appendix C work with the device. Make note of the code if it seems to be the right one, and try the next one. You are trying to find the one that has the most functions to operate your equipment. If there are any functions missing, you will learn them from your original remote in the “Using Learning Method” section on page C-7. 10. Continue to program other components by repeating from Step 1 above.
Appendix C RV-8 code is the one that will have the functions that more closely match the device than the others, so it is advised to try them all. See Step 9 below. (Press the UP or DOWN button within 20 seconds of beginning programming; otherwise the remote will revert to the SETUP menu, and then after a period of time, it will go back to the MAIN device page.
Appendix C PROGRAMMING THE FUNCTION BUTTONS To program the Function Buttons: 1. Go to the SETUP mode by pressing both the HOME and ENT buttons simultaneously for three seconds. Lexicon example, to erase a punch through from a TV to a SAT device, just “punch” through the TV to the TV. See “Programming “Punch Through” Functions” on page 12 for more information. 2. Press the LEARN button next to the LCD screen. PROGRAMMING THE TEN DEVICE BUTTONS 3.
Appendix C RV-8 Note: Follow these instructions only if you actually want a code sent when changing devices. It may not be desired to send out codes when changing to a device. For example, you program the RV-8’s TV input code on the TV device, and are currently in the DVD device pages. The RV-8’s input is set to DVD. Now you want to quickly adjust the picture on the TV. If the TV device button is pushed, it will change the input on the RV-8 to TV and you will not be able to adjust the picture for the DVD.
Appendix C Lexicon PROGRAMMING MACRO BUTTONS A “macro” is a series of commands that can be sent with the push of a single button. There are two types of macro functions that can be programmed: functions involving the M1, M2 and M3 buttons;or functions involving the POWER and SYSTEM OFF buttons. Each of these buttons is designed to send up to 20 commands.
Appendix C RV-8 7. Return to step 4 until all desired commands are programmed. 1. Press HOME and ENT simultaneously for three seconds. 8. Save the commands selected to the macro button by pressing the CH UP button. 2. Press MACRO. 9. Once you complete the programming and wish to exit from this mode, press the HOME button. Exit from the SET UP mode by pressing the HOME button once again.
Appendix C Note: A macro can end on any page, including the HOME page. In the previous example, the macro was ended on the SAT page before saving it, as this was the desired endpoint. PROGRAMMING “PUNCH THROUGH” FUNCTIONS The RV-8 volume control can be used in a different mode using the volume “punch through” feature.
Appendix C RV-8 ERASING FAVORITE CHANNEL BUTTONS ERASING PUNCH THROUGH FUNCTIONS To erase favorite channel buttons: To erase “punch through” functions: 1. Go to the SETUP mode by pressing both the HOME and ENT buttons simultaneously for three seconds. 1. Go to the SETUP mode by pressing the HOME and ENT buttons simultaneously for three seconds. 2. Press the ERASE button next to the LCD screen. 2. Press the PUNCH button next to the LCD screen. 3. Press the FAV button. 3.
Appendix C Lexicon 5. To edit DEVICE button text, skip Steps 3 and 4 and press the PAGE button before selecting the Device button. 6. The character to be changed will blink. To change the character use the number pad buttons on the remote control. The characters assigned to each number pad button are shown below. It will cycle to a different character each time the same number pad button is pressed. Note: Move the cursor left or right using the joystick.
Appendix C RV-8 4. If you wish to erase all the learned functions in the RV-8 remote, press the ALL button and then press the SURE? button at the next LCD screen. 5. To erase all the buttons in a single device or an individual button in the device, press the DEVICE button. 6. Press the device button (TV, VCR, MAIN, etc.) to erase the button(s) from the device. Note: Press the PAGE button and then press the DEVICE button (TV, VCR, etc.) to erase the learned function in the device button itself.
Appendix C ADJUSTING THE LCD CONTRAST To adjust the LCD contrast: Pressing the HOME button and Up on the joystick simultaneously will make the LCD contrast darker. Pressing the HOME button and Down on the joystick simultaneously will make the LCD contrast brighter. BATTERY LIFE Under normal operating conditions, the batteries will last approximately six months. If the batteries are running low, there will be reduced range from the remote, commands that are not sent properly, or are not sent at all.
Appendix C RV-8 REPROGRAMMING THE ZONE AUDIO CODES TO DEFAULT CODES To reprogram the RV-8 zone audio codes: 1. Simultaneously press MAIN and ENT buttons to access SETUP mode. 2. Press the P-PRO button next to the LCD screen. 3. The remote should flash SELECT BUTTON at the bottom of the LCD screen. Press the button for the zone you wish to reprogram. 4. The remote should flash FROM TABLE at the bottom of the LCD screen. Select the MAIN zone button. 5. The remote should flash ENTER NUMBER.
Appendix C Lexicon THREE-DIGIT PREPROGRAMMED CODES AUDIO Manufacturer ADC ADCOM AIWA AKAI AMC AMEND AMX ANGSTROM ARCAM AUDIO ACCESS AUDIO ALCHEMY AUDIO DESIGN AUDIO EASE AUDIO FILE AUDIO MATRIX AUDIO SOURCE AUDIO TECHNICA B&K BOSE BRYSTON CARVER CASIO CHIRO CINEMA SOUND CITATION CLARION CURTIS MATHES DENON EIGER ELAN ENLIGHTENED AUDIO C-18 AUDIO Codes 007 082 092 225 161 269 018 104 170 202 203 213 211 188 138 189 125 126 127 128 258 281 282 054 196 142 141 147 135 194 221 011 021 196 207 071 167 273 13
Appendix C RV-8 AUDIO DVD Manufacturer Codes Manufacturer Codes PANASONIC PARASOUND PHAST PHILIPS PIONEER PROCEED RCA REALISTIC REVOX ROTEL SAMSUNG SANSUI SANYO SCOTT SEARS SHARP SHERWOOD SONY SOUNDESIGN SOUNDSTREAM SSI SUMO TAEKWANG TEAC TECHNICS THETA DIGITAL TOSHIBA WARDS YAMAHA ZENITH 032 195 219 177 129 130 132 261 196 249 250 251 063 014 033 039 044 045 050 069 159 168 116 035 078 198 144 268 010 048 117 156 067 019 056 073 075 095 162 074 083 085 016 040 048 110 119 065 228 047 059 019 091 07
Appendix C Lexicon SAT SAT Manufacturer Codes Manufacturer Codes ALPHASTAR 123 AMPLICA BIRDVIEW BSR CAPETRONICS CHANNEL MASTER CHAPARRAL CITOH CURTIS MATHES DRAKE DX ANTENNA ECHOSTAR ELECTROHOME EUROSAT FUJITSU GENERAL ELECTRIC GENERAL INSTRUMENT HITACHI HOME CABLE HOUSTON TRACKER HUGHES HYTEK HYUNDAI ICR JANIEL KATHREIN LEGEND LUTRON LUXOR MACOM MEMOREX NEXTWAVE NORSAT PACE 050 129 113 051 126 053 053 013 014 015 018 036 055 008 009 012 077 054 050 005 006 007 010 011 112 116 141 052 024 046 056
Appendix C RV-8 VCR Manufacturer VCR Codes Manufacturer Codes 034 161 MAGNAVOX 031 034 041 067 068 156 164 016 043 046 124 125 146 MARANTZ 012 031 067 069 AMPRO 072 MARTA 101 ANAM 031 MATSUI 027 030 AUDIO DYNAMICS 012 023 039 043 MEI 031 BROOKSONIC 035 037 129 MEMOREX 003 010 014 031 034 053 072 101 102 134 139 CANON 028 031 MGA 045 046 059 CAPEHART 108 MINOLTA 013 020 003 040 135 MITSUBISHI 013 020 045 046 051 059 061 142 151 049 CURTIS MATHES 031 041 MTC 034 040 D
Appendix C Lexicon VCR TV Manufacturer Codes Manufacturer SANYO SCOTT 003 007 010 014 134 102 017 037 112 129 131 ADMIRAL Codes 072 081 161 160 AKAL 197 146 SEARS 003 008 009 010 013 014 081 101 017 073 112 AMARK 112 143 SHARP 031 054 149 159 165 AMPRO 073 167 157 183 SHINTOM 024 AMSTRAD 052 SIGNATURE 034 ANAM 043 054 056 080 112 131 SONY 003 031 052 056 057 058 076 077 078 149 154 AOC 197 004 112 058 SOUNDESIGN 034 AUDIOVOX 076 STS 013 BLAUPUNKT 088 SYLVANIA 031 03
Appendix C RV-8 TV TV Manufacturer Codes Manufacturer Codes FUJITSU FUNAI 198 028 043 NEC 132 130 134 197 040 016 024 056 019 NIKEI 043 FUTURETECH 043 ONKING 043 GE 197 008 009 034 056 073 074 130 144 155 160 161 165 ONWA 043 004 091 157 183 OPTONICA 019 081 004 102 106 112 113 116 119 127 143 ORION 096 HALL MARK 004 PANASONIC 034 056 080 092 164 HITACHI 004 009 010 011 012 023 075 143 158 163 166 072 PHILCO 197 003 024 056 059 060 063 064 164 004 INFINITY 164 PHILIPS 1
Appendix C Lexicon TV Manufacturer CD Codes Manufacturer Codes SUPRE MACY 002 ADCOM 062 042 SYLVANIA 197 003 059 060 063 064 164 044 160 127 AIWA 059 065 088 089 105 122 170 187 TANDY 081 AKAI 085 195 202 TATUNG 056 062 AMC 231 232 TECHNICS 034 080 AMEND 118 TECHWOOD 004 ARCAM 238 TEKNIKA 002 003 004 024 028 043 072 101 143 AUDIO ACCESS 119 147 TELEFUNKEN 037 046 086 087 AUDIO EASE 165 TELERENT 072 AUDIO TECHNICA 046 TERA 172 BSR 037 057 TMK 004 CALIFORNIA AUD
Appendix C RV-8 CD CD Manufacturer Codes Manufacturer KENWOOD 185 007 023 055 071 072 142 137 RADIO SHACK Codes 182 KOSS KRELL 061 241 RCA 017 042 150 REALISTIC 042 050 051 102 181 182 187 KYOCERA 005 LOTTE 044 107 161 178 250 044 107 102 ROTEL SAE LUXMAN 011 028 070 076 SANSUI 044 069 107 128 171 190 125 LXI 059 SANYO 050 MAGNAVOX 044 107 SCOTT 069 102 MARANTZ 027 041 044 051 077 107 209 SHARP 026 031 051 066 MCINTOSH 212 SHERWOOD 003 019 051 096 112 115 119 166 MC
Appendix C Lexicon PHONO LD Manufacturer Codes Manufacturer Codes DENON 206 207 FUNAI 120 KENWOOD 152 013 3M AIWA ARCHER AUTON DMX DRAPER SCREEN DWIN EVERQUEST EXTRON FAROUDJA FUJI JERROLD JVC KENWOOD LITE-TOUCH LUTRON MAKITA MINDPATH NILES NSM PIANO DISC PLUS PHILIPS POLK AUDIO REPLAY RUSSOUND SCIENTIFIC ATLANTA SIMA SOLO ELECTRONICS SOMFY SONY STARCOM TURBOSCAN VELODYNE X-10 XANTECH 152 164 155 191 156 204 080 206 151 184 209 153 185 185 208 077 158 159 186 201 205 160 187 161 085 090 162 075
Appendix C RV-8 CABLE Manufacturer CABLE Codes Manufacturer Codes ABC 103 003 004 039 042 046 053 OAK 031 037 053 AMERICAST 099 PANASONIC 044 047 ANTRONIX 014 PARAGON 052 ARCHER 005 007 014 PHILIPS 006 012 013 020 085 095 BELL SOUTH 099 PIONEER 103 034 051 063 076 105 CENTURION 092 PRUCER 059 CENTURY 007 RCA 047 CITIZEN 007 RECOTON 098 COMBANO 080 081 REGAL 049 050 COMSAT 074 REGENCY 057 COMTRONICS 030 SAMSUNG 030 DIGICABLE 101 SCIENTIFIC ATLANTA 003 011 0
Appendix C Lexicon TAPE Manufacturer Codes AIWA CARVER DENON FISHER GOLDSTAR HARMAN KARDON JVC KENWOOD LINN LUXMAN MAGNAVOX MARANTZ MCINTOSH MITSUBISHI NAD NAKAMICHI ONKYO OPTIMUS PANASONIC PHILIPS PIONEER QUASAR SANSUI SHARP SHERWOOD SONY TEAC TECHNICS TOSHIBA VICTOR YAMAHA 015 071 100 114 006 008 027 024 036 105 227 229 064 011 233 106 116 239 240 005 013 023 026 064 145 146 181 190 124 035 137 139 027 014 027 056 065 087 238 242 243 029 048 244 245 025 002 012 016 017 018 019 115 026 054 055 007 010
D Appendix Installation Worksheet ................................................................
Appendix D Lexicon INSTALLATION WORKSHEET INPUT SETUP NAME DIGITAL IN ANALOG IN ANLG IN LVL VIDEO IN COMPONENT IN 2-CH D 5.
Appendix D RV-8 SPEAKER SETUP CUSTOM SETUP THX SETUP FRONT LEFT/RIGHT THX 80Hz CENTER THX 80Hz SIDE LEFT/RIGHT THX 80Hz SPEAKER DISTANCES LEVELS CALIBRATION REAR LEFT/RIGHT SUBWOOFER THX 80Hz ULTRA2SUB BGC ASA UNITS BASS PEAK LIMITERS CAL NOISE SUB LIMITER LIMIT ADJ I/O CONFIG Analog Inputs Amplifier Outputs SETTINGS 8 STEREO INPUTS 5 ST. & (1) 5.1 ANLG MAIN 7.1 MAIN 5.1 & ZONE2 2.0 2 ST. & (2) 5.1 ANLG MAIN 5.1 & ZONE3 2.
Appendix D INSTALLATION WORKSHEET Lexicon (continued) DISPLAY SETUP TRIGGER SETUP TUNER SETUP ON-SCREEN DISPLAY Circle all parameters set to ON. REGION REMOTE ONLY DVD1 DVD2 SAT VCR TV CD TUNER PHONO ZONE2 INPUTS ZONE3 INPUTS FILM TV MUSIC MUSIC SURR PLIIx + PLIIx MOV PLIIx MUS PLII + PLII MOVIE PLII MUSIC PL + PRO LOGIC + CIN MUSIC NIGHTCLUB CONCERT HALL CHURCH CATHEDRAL PANORAMA 2-CH SURROUND 2-CHANNEL MONO LOGIC MONO SURROUND MONO 5.1 FILM 5.1 TV 5.1 MUSIC SCAN SENS MUSIC 5.1 PLIIx MOV 5.
Appendix D RV-8 3-DIGIT PREPROGRAMMED CODES WORKSHEET COMPONENT MANUFACTURER CODE(S) USED DVD1 DVD2 SAT VCR TV CD PHONO D-5
Appendix D Lexicon PREPROGRAMMED LCD TEXT FOR OTHER DEVICES DVD1 PROG DISPL CLEAR REPEA A-B DVD2 MENU SETUP MEMO TITLE SHUFF PAGE 1 SYSTEM-OFF POWER VOL UP VOL DN CH UP CH DN MUTE PRE-CH UP DOWN LEFT RIGHT SELECT PLAY STOP REW FF , MENU , GUIDE O, EXIT II, INFO 1 2 3 4 5 6 7 8 9 0 DISPLAY ENTER D-6 RANDO RETUR AUDIO TIME SOUND SAT ANGLE S-ON S-CHA SLOW+ SLOW- PAGE 2 OFF ON/OFF SKIP+ SKIPSEARCH UP DN LEFT EJECT PAUSE 1 2 3 4 5 6 7 8 9 0 DISPLAY ENTER FAUCH ALPHA NEXT VIEW ALT SAT ACTIO REC SERV
Appendix D RV-8 TV TV T/V SLEEP CC CC-SN RESET INPUT A-CH ADD DELET ANT PAGE 1 SYSTEM-OFF POWER VOL UP VOL DN CH UP CH DN MUTE PRE-CH UP DOWN LEFT RIGHT SELECT PLAY STOP REW FF , MENU , GUIDE O, EXIT II, INFO 1 2 3 4 5 6 7 8 9 0 DISPLAY ENTER CD CD P-ON P-OFF SWAP STILL SOURC LOCAT POSI FREEZ PROG INTRO DISPL TIME CLEAR FADER REPEA EDIT A-B PAGE 2 PAGE 1 OFF ON/OFF VOL UP VOL DN SKIP+ SKIPMUTE PRE CH UP DN LEFT RIGHT SELECT MENU GUIDE EXIT INFO 1 2 3 4 5 6 7 8 9 0 DISPLAY ENTER SYSTEM-OFF PO
Index Numerics 2 ST. & (2) 5.1 ANLG option, 3-61 2.0 ENCODING parameter, 2-34 2CH BYPASS listening mode, 6-34 2CH BYPASS STATUS menu, 2-32 2-CH MODE menu, 3-15 2-CH Parameter, D-2 2-CH parameter, 3-12 2CH STATUS menu, 2-30 2-CH SURROUND listening mode, 6-15 2-CHANNEL listening mode, 6-15 5, 6-26 5 SPKR ENHANCE parameter, 6-4, 6-5, 6-16, 6-17, 626, 6-29, 6-30, 6-39 5 ST. & 5.1 ANLG option, 3-61 5.1 2-CHANNEL listening mode, 6-23 5.1 ANALOG STATUS menu, 2-33 5.1 L7 FILM listening mode, 6-16 5.
Index CATHEDRAL listening mode, 6-12 CENTER DEPTH parameter, 6-11, 6-12, 6-40 CENTER MIX LVL parameter, 2-34 CENTER MIX parameter, 6-23, 6-29, 6-33, 6-40 Center output connector, 2-7 CENTER parameter, 3-29, 3-31, 6-37, 6-40 changing input names, 3-5 CHANNELS parameter, 2-34 checking microphones, 3-41 CHURCH listening mode, 6-12 CLEAR ALL parameter, 3-75 CNTR DLY SAMPLES parameter, 6-23, 6-29, 6-33, 6-40 COMPONENT IN parameter, 3-7, 3-11 COMPONENT OSD parameter, 3-17, 3-20, 3-21, D-2 component video input co
Index RV-8 I I/O CONFIG SETUP menu, 3-2 INPUT BALANCE parameter, 6-13, 6-42 input connectors, 2-7 microphone, 2-8 INPUT NAME menu, 3-5 INPUT parameter, 2-35 INPUT SELECT parameter, 3-17, 3-19, D-2 input selection buttons, 2-4 remote control, 2-18 INPUT SETUP menu, 3-2, 3-4, D-2 INPUT TYPE parameter, 2-35 INPUTS Advanced, 3-17 changing names, 3-5 Main Zone, 2-28, 3-2 installation considerations, 1-5 INTERNAL NOISE TEST, 3-53, 3-56 IR IN connector, 2-9 IR receiver, 2-3 preferred, 6-3 selection buttons, 6-3
Index 6-10, 6-11, 6-12, 6-13, 6-15, 6-16, 6-17, 6-19, 6-20, 6-21, 6-22, 6-23, 6-26, 6-27, 6-28, 6-29, 6-30, 6-31, 6-32, 6-33, 6-43 Output levels, calibrating automatic, 3-36 Bass Peak Limiters, 3-58 manual, 3-55 P PANORAMA listening mode, 6-13 PANORAMA parameter, 6-8, 6-43 parameter drop-down menus, 2-16 parameter relationships, 6-47 parameters listening mode menu, 6-39 STATUS menu, 2-34 parameters, preferred listening mode selection, 3-12 phono input connectors, 2-8 POWER MANAGEMENT menu, 3-3 power switch
Index RV-8 9 parameter, 3-17, 3-18 S-VIDEO OSD 4 3 parameter, 3-17, 3-20 S-Video output connectors, 2-8 T three-digit preprogrammed codes, C-18 THX listening mode, 6-18 THX MUSIC listening mode, 6-19 THX SETUP Menu, 3-29 THX SPEAKER SETUP screen, 3-28, 3-28 THX SurEX listening mode, 6-18 THX UL2Cin listening mode, 6-18 THX ULTRA2 SUB parameter, 3-29, 3-34 TILT EQ parameter, 4-2 frequency response graph, 4-5 TREB CUT RT parameter, 6-46 TREBLE parameter, 4-2 frequency response graph, 4-3 trigger output conn
PRODUCT REGISTRATION Please register this product within 15 days of purchase. To do so, complete and return this card or register online at www.lexicon.com. Retain the sales receipt for proof of coverage. LIMITED WARRANTY Harman Specialty Group offers the following warranty on this product: What is the Duration of this Warranty? This warranty will remain in effect for three (3) years from the original date of purchase.
A Harman International Company Part No.