MS810 Series User's Guide Important: Click here before using this guide. October 2014 Machine type(s): 4063 Model(s): 210, 230, 23E, 410, 430, 630, 63E www.lexmark.
Contents 2 Contents Safety information.......................................................................................5 Overview.....................................................................................................7 Using this guide.........................................................................................................................................7 Finding information about the printer................................................................................
Contents 3 Paper and specialty media guide..............................................................175 Using specialty media............................................................................................................................175 Paper guidelines....................................................................................................................................176 Supported paper sizes, types, and weights............................................................
Contents 4 [x]‑page jam, remove paper, open finisher rear door. Leave paper in bin. [451].................................277 [x]‑page jam, remove paper, open expander rear door. Leave paper in bin. [41y.xx]..........................278 [x]‑page jam, remove paper, open mailbox rear door. Leave paper in bin. [43y.xx]............................280 Troubleshooting.......................................................................................282 Understanding the printer messages....................
Safety information 5 Safety information Connect the power cord directly to an appropriately rated and properly grounded electrical outlet that is near the product and easily accessible. CAUTION—POTENTIAL INJURY: Do not use this product with extension cords, multioutlet power strips, multioutlet extenders, or other types of surge or UPS devices.
Safety information 6 CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
Overview 7 Overview Using this guide This User’s Guide provides general and specific information on using the printer models that are listed on the cover page.
Overview 8 What are you looking for? Find it here Help using the printer software Windows or Mac Help—Open a printer software program or application, and then click Help. Click ? to view context‑sensitive information. Notes: • Help is automatically installed with the printer software. • The printer software is located in the printer program folder or on the desktop, depending on your operating system.
Selecting a location for the printer 9 Selecting a location for the printer CAUTION—POTENTIAL INJURY: The printer weight is greater than 18 kg (40 lb) and requires two or more trained personnel to lift it safely. When selecting a location for the printer, leave enough room to open trays, covers, and doors. If you plan to install any hardware options, then leave enough room for them also. It is important to: • Set up the printer near a properly grounded and easily accessible electrical outlet.
Selecting a location for the printer 10 1 Right side 152 mm (6 in.) 2 Front 508 mm (20 in.) 3 Left side 152 mm (6 in.) 4 Rear 152 mm (6 in.) 5 Top 115 mm (4.5 in.) 1 Right side 152 mm (6 in.) 2 Front 508 mm (20 in.) 3 Left side 152 mm (6 in.) 4 Rear 152 mm (6 in.) 5 Top 115 mm (4.5 in.
Additional printer setup 11 Additional printer setup Installing internal options CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
Additional printer setup 2 Using a screwdriver, loosen the screws on the controller board shield. 3 Remove the shield.
Additional printer setup 13 4 Use the following illustration to locate the appropriate connector: Warning—Potential Damage: Controller board electronic components are easily damaged by static electricity. Touch a metal surface on the printer first before touching any controller board electronic component or connector.
Additional printer setup 5 Align the screws with the holes on the shield, and then reattach the shield. 6 Tighten the screws on the shield.
Additional printer setup 15 7 Reattach the access cover. 1 2 Installing a memory card CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
Additional printer setup 16 4 Push the memory card straight into the connector, and then push the card toward the controller board wall until it clicks into place. 5 Reattach the controller board shield, and then the controller board access cover. Installing an Internal Solutions Port The controller board supports one optional Lexmark Internal Solutions Port (ISP). Note: This task requires a flat‑head screwdriver.
Additional printer setup 17 3 Unpack the ISP kit. 1 2 4 3 1 ISP solution 2 Screw for attaching the plastic bracket to the ISP 3 Screws for attaching the ISP mounting bracket to the controller board shield 4 Plastic bracket 4 Remove the metal cover from the ISP opening. a Loosen the screw. b Lift the metal cover, and then pull it out completely.
Additional printer setup 18 1 2 3 5 Align the posts of the plastic bracket with the holes on the controller board cage, and then press the plastic bracket on the controller board cage until it clicks into place. Make sure the cables are neatly tucked under the plastic bracket. 6 Install the ISP on the plastic bracket. Note: Hold the ISP at an angle over the plastic bracket so that any overhanging connectors will pass through the ISP opening in the controller board cage.
Additional printer setup 7 Lower the ISP toward the plastic bracket until the ISP is seated between the guides of the plastic bracket. 8 Use the provided thumbscrew for the ISP to attach the plastic bracket to the ISP. Note: Turn the screw clockwise, enough to hold the ISP in place, but do not tighten it yet.
Additional printer setup 9 Attach the two provided screws to secure the ISP mounting bracket to the controller board shield. 10 Tighten the thumbscrew that is attached to the ISP. Warning—Potential Damage: Do not screw it on too tightly. 11 Connect the ISP solution interface cable into the receptacle of the controller board. Note: The plugs and receptacles are color-coded.
Additional printer setup 21 Installing an optional card CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
Additional printer setup 22 Note: The entire length of the connector on the card must touch and be flushed against the controller board. 5 Close the controller board access door. Note: When the printer software and any hardware options are installed, it may be necessary to manually add the options in the printer driver to make them available for print jobs. For more information, see “Adding available options in the print driver” on page 34.
Additional printer setup 3 Locate the appropriate connector on the controller board cage. Note: If an optional ISP is currently installed, then the printer hard disk must be installed onto the ISP.
Additional printer setup 24 To install a printer hard disk onto the ISP: a Remove the screws attached to the printer hard disk mounting bracket, and then remove the bracket. b Align the standoffs of the printer hard disk to the holes in the ISP, and then press the printer hard disk down until the standoffs are in place. Installation warning: Hold only the edges of the printed circuit board assembly. Do not touch or press on the center of the printer hard disk. Doing so may cause damage.
Additional printer setup 25 4 Align the standoffs of the printer hard disk to the holes in the controller board cage, and then press the printer hard disk down until the standoffs are in place. Installation warning: Hold only the edges of the printed circuit board assembly. Do not touch or press on the center of the printer hard disk. Doing so may cause damage. Note: Make sure the cables are neatly tucked under the printer hard disk.
Additional printer setup Removing a printer hard disk Note: This task requires a flat‑head screwdriver. CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
Additional printer setup 27 Warning—Potential Damage: Controller board electronic components are easily damaged by static electricity. Touch a metal surface on the printer before touching any controller board electronic components or connectors. 1 Access the controller board. For more information, see “Accessing the controller board” on page 11. 2 Unplug the printer hard disk interface cable from the controller board, leaving the cable attached to the printer hard disk.
Additional printer setup 28 4 Remove the printer hard disk. 5 Set aside the printer hard disk. Installing hardware options Order of installation CAUTION—POTENTIAL INJURY: The printer weight is greater than 18 kg (40 lb) and requires two or more trained personnel to lift it safely.
Additional printer setup 29 Installing optional trays CAUTION—POTENTIAL INJURY: The printer weight is greater than 18 kg (40 lb) and requires two or more trained personnel to lift it safely. CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the electrical outlet before continuing.
Additional printer setup 8 Align the printer with the tray, and then slowly lower the printer into place. Note: Optional trays lock together when stacked.
Additional printer setup 31 9 Connect the power cord to the printer, then to a properly grounded electrical outlet, and then turn on the printer.
Additional printer setup 32 Note: When the printer software and any optional trays are installed, you may need to manually add the options in the printer driver to make them available for print jobs. For more information, see “Adding available options in the print driver” on page 34. To uninstall the optional trays, slide the latch on the right side of the printer toward the front of the printer until it clicks into place, and then remove stacked trays one at a time from the top to the bottom.
Additional printer setup 33 6 1 2 3 4 5 1 Use the To Parallel port Connect the printer to a computer. Note: This can also be used in installing an optional Internal Solutions Port (ISP). 2 USB port Attach an optional wireless network adapter. 3 Ethernet port Connect the printer to a network. 4 USB printer port Connect the printer to a computer. 5 Security slot Attach a lock that will secure the controller board.
Additional printer setup Setting up the printer software Installing the printer 1 Obtain a copy of the software installer package. 2 Run the installer, and then follow the instructions on the computer screen. 3 For Macintosh users, add the printer. Note: Obtain the printer IP address from the TCP/IP section in the Network/Ports menu. Adding available options in the print driver For Windows users 1 Open the printers folder.
Additional printer setup 35 In Windows 7 or earlier a Click , or click Start and then click Run. b Type control printers. c Press Enter, or click OK. 2 Select the printer you want to update, and then do either of the following: • For Windows 7 or later, select Printer properties. • For earlier versions, select Properties. 3 Navigate to the Configuration tab, and then select Update Now ‑ Ask Printer. 4 Apply the changes.
Additional printer setup 36 Preparing to set up the printer on a wireless network Notes: • Make sure your wireless network adapter is installed in your printer and working properly. For more information, see the instruction sheet that came with the wireless network adapter. • Make sure your access point (wireless router) is turned on and is working properly.
Additional printer setup 37 Connecting the printer to a network using the Wireless Setup Wizard Before you begin, make sure that: • A wireless network adapter is installed in the printer and is working properly. For more information, see the instruction sheet that came with the wireless network adapter. • The Ethernet cable is disconnected from the printer. • Active NIC is set to Auto.
Additional printer setup 38 Using the Push Button Configuration method 1 Depending on your printer model, navigate to either of the following: • > Settings > > Networks/Ports > > Wi‑Fi Protected Setup > > Network [x] > > Network [x] Setup > > Wireless > > Start Push Button Method • > Network/Ports > Network [x] > Network [x] Setup > Wireless > Wi‑Fi Protected Setup > Start Push Button Method • > Network/Ports > Network [x] > Network [x] Setup > Wireless > Wi‑Fi Protected Setup > Start Push Butt
Additional printer setup 39 3 Modify the settings to match the settings of your access point (wireless router). Note: Make sure to enter the correct SSID, security method, preshared key or passphrase, network mode, and channel. 4 Click Submit. 5 Turn off the printer, and then disconnect the Ethernet cable. Then wait for at least five seconds, and then turn the printer back on. 6 To verify if your printer is connected to the network, print a network setup page.
Using MS810n, MS810dn, MS811n, MS811dn, MS812dn 40 Using MS810n, MS810dn, MS811n, MS811dn, MS812dn Learning about the printer Printer configurations Basic model 1 Standard bin 2 Printer control panel 3 Multipurpose feeder 4 Standard 550‑sheet tray (Tray 1) Fully configured model CAUTION—TIPPING HAZARD: Floor-mounted configurations require additional furniture for stability. You must use either a printer stand or printer base if you are using multiple input options.
Using MS810n, MS810dn, MS811n, MS811dn, MS812dn 41 The following illustration shows the maximum number of optional finishers and trays that are supported by the printer. For more information on other configurations, visit www.lexmark.com/multifunctionprinters.
Using MS810n, MS810dn, MS811n, MS811dn, MS812dn 42 • The output expander is the only option that can be placed on top of the high‑capacity output expander. • The output expander and mailbox may be installed in any order. When using optional trays: • • • • Always use a caster base when the printer is configured with a 2100‑sheet tray. The 2100‑sheet tray must always be at the bottom of a configuration. A maximum of four optional trays may be configured with the printer.
Using MS810n, MS810dn, MS811n, MS811dn, MS812dn 10 Use the To USB port Connect a flash drive to the printer. 43 Note: Only the front USB port supports flash drives. Understanding the colors of the Sleep button and indicator lights The colors of the Sleep button and indicator lights on the printer control panel signify a certain printer status or condition. Indicator light Printer status Off The printer is off or in Hibernate mode.
Using MS810n, MS810dn, MS811n, MS811dn, MS812dn 44 Notes: • The smallest supported Universal size is 70 x 127 mm (2.76 x 5 inches) for one‑sided printing and 105 x 148 mm (4.13 x 5.83 inches) for two‑sided (duplex) printing. • The largest supported Universal size is 216 x 356 mm (8.5 x 14 inches) for one‑sided and two‑sided printing. • When printing on paper less than 210 mm (8.3 inches) wide, the printer may print at a reduced speed after a period of time to ensure the best print performance.
Using MS810n, MS810dn, MS811n, MS811dn, MS812dn 45 2 Squeeze and slide the width guide to the correct position for the size of the paper being loaded until it clicks into place. Note: Use the paper size indicators at the bottom of the tray to help position the guides.
Using MS810n, MS810dn, MS811n, MS811dn, MS812dn 46 3 Unlock the length guide, and then squeeze and slide the guide to the correct position for the size of the paper being loaded. Notes: • Lock the length guide for all paper sizes. • Use the paper size indicators at the bottom of the tray to help position the guides.
Using MS810n, MS810dn, MS811n, MS811dn, MS812dn 47 4 Flex the sheets back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface. 5 Load the paper stack with the printable side facedown. Note: Make sure the paper or envelope is loaded properly. • There are different ways of loading letterhead depending on whether an optional staple finisher is installed or not.
Using MS810n, MS810dn, MS811n, MS811dn, MS812dn 48 • Do not slide the paper into the tray. Load paper as shown in the illustration. • If you are loading envelopes, then make sure that the flap side is facing up and the envelopes are on the left side of the tray.
Using MS810n, MS810dn, MS811n, MS811dn, MS812dn • Make sure the paper is below the solid line, which is the maximum paper fill indicator. Warning—Potential Damage: Overfilling the tray can cause paper jams.
Using MS810n, MS810dn, MS811n, MS811dn, MS812dn 50 • When using card stock, labels, or other types of specialty media, make sure the paper is below the dashed line, which is the alternate paper fill indicator. 6 For custom‑ or Universal‑size paper, adjust the paper guides to lightly touch the sides of the stack, and then lock the length guide. 7 Insert the tray. 8 From the printer control panel, set the paper size and paper type in the Paper menu to match the paper loaded in the tray.
Using MS810n, MS810dn, MS811n, MS811dn, MS812dn 51 Loading the 2100‑sheet tray CAUTION—POTENTIAL INJURY: To reduce the risk of equipment instability, load each tray separately. Keep all other trays closed until needed. 1 Pull out the tray. 2 Adjust the width and length guides. Loading A5‑size paper a Pull up and slide the width guide to the position for A5.
Using MS810n, MS810dn, MS811n, MS811dn, MS812dn 52 b Squeeze and slide the length guide to the position for A5 until it clicks into place. 2 1 c Remove the A5 length guide from its holder. 1 d Insert the A5 length guide into its designated slot. Note: Press the A5 length guide until it clicks into place.
Using MS810n, MS810dn, MS811n, MS811dn, MS812dn 53 Loading A4‑, letter‑, legal‑, oficio‑, and folio‑size paper a Pull up and slide the width guide to the correct position for the size of the paper being loaded.
Using MS810n, MS810dn, MS811n, MS811dn, MS812dn 54 b If the A5 length guide is still attached to the length guide, then remove it from its place. If the A5 length guide is not attached, then proceed to step d. c Put the A5 length guide in its holder.
Using MS810n, MS810dn, MS811n, MS811dn, MS812dn 55 d Squeeze the length guide and slide it to the correct position for the size of the paper being loaded until it clicks into place. 3 Flex and fan the sheets to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface. 4 Load the paper stack with the printable side facedown. Note: Make sure the paper is loaded properly.
Using MS810n, MS810dn, MS811n, MS811dn, MS812dn 56 Without an optional staple finisher With an optional staple finisher C One‑sided printing AB C AB One‑sided printing C C Two‑sided printing AB AB Two‑sided printing • If you are loading prepunched paper for use with the staple finisher, then make sure the holes on the long edge of the paper are on the right side of the tray.
Using MS810n, MS810dn, MS811n, MS811dn, MS812dn • Make sure the paper is below the maximum paper fill indicator. Warning—Potential Damage: Overfilling the tray can cause paper jams. 5 Insert the tray. Note: Press the paper stack down while inserting the tray.
Using MS810n, MS810dn, MS811n, MS811dn, MS812dn 58 6 From the printer control panel, set the size and type in the Paper menu to match the paper loaded in the tray. Note: Set the correct paper size and type to avoid paper jams and print quality problems. Loading the multipurpose feeder 1 Pull down the multipurpose feeder door. Note: Do not load or close the multipurpose feeder while a job is printing.
Using MS810n, MS810dn, MS811n, MS811dn, MS812dn 59 2 Pull the multipurpose feeder extender. LTR A4 A5 EX B5 EC Note: Guide the extender gently so that the multipurpose feeder is fully extended and open. 3 Slide the width guide to the correct position for the size of the paper being loaded. LT R A4 A5 EX EC B 5 Note: Use the paper size indicators on the bottom of the tray to help position the guides.
Using MS810n, MS810dn, MS811n, MS811dn, MS812dn 60 LT R A 4 A 5 C E X E B 5 4 Prepare the paper or specialty media for loading. • Flex sheets of paper back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface. • Hold transparencies by the edges, and then fan them. Straighten the edges on a level surface. Note: Avoid touching the printable side of the transparencies. Be careful not to scratch them.
Using MS810n, MS810dn, MS811n, MS811dn, MS812dn 61 • There are different ways of loading letterhead depending on whether an optional staple finisher is installed or not. A A B C B C Without an optional staple finisher With an optional staple finisher One‑sided printing A B C One‑sided printing Two‑sided printing Two‑sided printing • If you are loading prepunched paper for use with the staple finisher, then make sure the holes on the long edge of the paper are on the right side of the tray.
Using MS810n, MS810dn, MS811n, MS811dn, MS812dn 62 5 4 A B C E X E A 5 R T L • Load envelopes with the flap side down and on the left of the multipurpose feeder. Warning—Potential Damage: Never use envelopes with stamps, clasps, snaps, windows, coated linings, or self‑stick adhesives. These envelopes may severely damage the printer. • Make sure the paper or specialty media is below the maximum paper fill indicator. Warning—Potential Damage: Overfilling the feeder can cause paper jams.
Using MS810n, MS810dn, MS811n, MS811dn, MS812dn 63 Linking and unlinking trays The printer links trays when the specified paper size and type are the same. When a linked tray becomes empty, paper feeds from the next linked tray. To prevent trays from linking, assign a unique custom paper type name. Linking and unlinking trays 1 Open a Web browser, and then type the printer IP address in the address field.
Using MS810n, MS810dn, MS811n, MS811dn, MS812dn 3 Press 64 . 4 Press Custom Types, and then verify if the new custom paper type name has replaced the custom name. Assigning a custom paper type Using the Embedded Web Server 1 Open a Web browser, and then type the printer IP address in the address field. Notes: • View the printer IP address in the TCP/IP section in the Network/Ports menu. The IP address appears as four sets of numbers separated by periods, such as 123.123.123.123.
Using MS810n, MS810dn, MS811n, MS811dn, MS812dn 65 For Macintosh users a Customize the settings in the Page Setup dialog if necessary: 1 With a document open, choose File > Page Setup. 2 Choose a paper size or create a custom size to match the paper loaded. 3 Click OK. b Customize the settings in the Page Setup dialog if necessary: 1 With a document open, choose File > Print. If necessary, click the disclosure triangle to see more options.
Using MS810n, MS810dn, MS811n, MS811dn, MS812dn 66 Printing from a flash drive or mobile device Printing from a flash drive Notes: • Before printing an encrypted PDF file, you will be prompted to enter the file password from the printer control panel. • You cannot print files for which you do not have printing permissions. 1 Insert a flash drive into the USB port. Notes: • A flash drive icon appears on the printer control panel and in the held jobs icon when a flash drive is installed.
Using MS810n, MS810dn, MS811n, MS811dn, MS812dn 67 2 From the printer control panel, select the document you want to print. 3 Press the left or right arrow button to specify the number of copies for printing, and then press . Notes: • Do not remove the flash drive from the USB port until the document has finished printing. • If you leave the flash drive in the printer after leaving the initial USB menu screen, then access held jobs from the printer control panel to print files from the flash drive.
Using MS810n, MS810dn, MS811n, MS811dn, MS812dn Recommended flash drives 68 File type • Lexar JumpDrive FireFly (512MB and 1GB) • SanDisk Cruzer Micro (512MB and 1GB) • Sony Micro Vault Classic (512MB and 1GB) Documents: • .pdf • .xps Images: • • • • • • • • .dcx .gif .jpeg or .jpg .bmp .pcx .tiff or .tif .png .
Using MS810n, MS810dn, MS811n, MS811dn, MS812dn 2 Press 69 . Printing confidential and other held jobs Note: Confidential and Verify print jobs are automatically deleted from memory after printing. Repeat and Reserve jobs are held in the printer until you choose to delete them. For Windows users 1 With a document open, click File > Print. 2 Click Properties, Preferences, Options, or Setup. 3 Click Print and Hold.
Using MS810n, MS810dn, MS811n, MS811dn, MS812dn 70 Printing information pages Printing a font sample list 1 From the printer control panel, navigate to: > Settings > > Reports > > Print Fonts 2 Press the up or down arrow button to select the font setting. 3 Press . Note: The PPDS fonts appear only when the PPDS data stream is activated.
Using MS810n, MS810dn, MS811n, MS811dn, MS812dn 71 Managing your printer Finding advanced networking and administrator information This chapter covers basic administrative support tasks using the Embedded Web Server. For more advanced system support tasks, see the Networking Guide on the Software and Documentation CD or the Embedded Web Server — Security: Administrator's Guide on the Lexmark support Web site at http://support.lexmark.com.
Using MS810n, MS810dn, MS811n, MS811dn, MS812dn 72 Notification Description Off The normal printer behavior for all supplies occurs. E‑mail Only The printer generates an e‑mail when the supply condition is reached. The status of the supply appears on the menus page and status page. Warning The printer displays the warning message and generates an e‑mail about the status of the supply. The printer does not stop when the supply condition is reached.
Using MS810n, MS810dn, MS811n, MS811dn, MS812dn 73 3 To change the language, select a language from the drop-down menu, and then click Click here to submit language. 4 Click Printer Settings. 5 Type the IP addresses of the source and target printers in their appropriate fields. Note: If you want to add or remove a target printer, then click Add Target IP or Remove Target IP. 6 Click Copy Printer Settings.
Using MS810n, MS810dn, MS811n, MS811dn, MS812dn 74 1 Open a Web browser, and then type the printer IP address in the address field. Notes: • View the printer IP address in the TCP/IP section in the Network/Ports menu. The IP address appears as four sets of numbers separated by periods, such as 123.123.123.123. • If you are using a proxy server, then temporarily disable it to load the Web page correctly. 2 Click Device Status > More Details.
Using MS810n, MS810dn, MS811n, MS811dn, MS812dn 75 Reducing printer noise Enable Quiet mode to reduce the printer noise. 1 From the printer control panel, navigate to: > Settings > > Settings > > General Settings > > Quiet Mode > 2 Select a setting. Use To On Reduce printer noise. Notes: • Print jobs process at a reduced speed. • Printer engine motors do not start until a document is ready to print. There is a short delay before the first page is printed.
Using MS810n, MS810dn, MS811n, MS811dn, MS812dn 76 Using Hibernate mode Hibernate is an ultra‑low‑power saving mode. Notes: • Three days is the default amount of time before the printer enters Hibernate mode. • Make sure to wake the printer from Hibernate mode before sending a print job. A hard reset or a long press of the Sleep button wakes the printer from Hibernate mode. • If the printer is in Hibernate mode, then the Embedded Web Server is disabled.
Using MS810n, MS810dn, MS811n, MS811dn, MS812dn 77 Securing the printer Using the security lock feature The printer is equipped with a security lock feature. When a lock compatible with most laptop computers is attached, the printer is locked. When locked, the controller board shield and the controller board cannot be removed. Attach a security lock to the printer in the location shown.
Using MS810n, MS810dn, MS811n, MS811dn, MS812dn 78 • The printer is being removed from your premises for service. • The printer is being sold to another organization. Disposing of a printer hard disk Note: Some printer models may not have a printer hard disk installed. In high‑security environments, it may be necessary to take additional steps to make sure that confidential data stored in the printer hard disk cannot be accessed when the printer—or its hard disk—is removed from your premises.
Using MS810n, MS810dn, MS811n, MS811dn, MS812dn 79 Erasing printer hard disk memory Notes: • Some printer models may not have a printer hard disk installed. • Configuring Erase Temporary Data Files in the printer menus lets you remove residual confidential material left by print jobs by securely overwriting files that have been marked for deletion. Using the printer control panel 1 Turn off the printer. 2 Hold down 2 and 6 while turning the printer on.
Using MS810n, MS810dn, MS811n, MS811dn, MS812dn 80 3 From the Disk Encryption menu, select Enable. Notes: • Enabling disk encryption will erase the content of the printer hard disk. • Disk encryption can take from several minutes to more than an hour, during which the printer will be unavailable for other user tasks. Using the printer control panel 1 Turn off the printer. 2 Hold down 2 and 6 while turning the printer on. Release the buttons only when the screen with the progress bar appears.
Using MS810de 81 Using MS810de Learning about the printer Printer configurations Basic model 1 Standard bin 2 Printer control panel 3 Multipurpose feeder 4 Standard 550‑sheet tray (Tray 1) Fully configured model CAUTION—TIPPING HAZARD: Floor-mounted configurations require additional furniture for stability. You must use either a printer stand or printer base if you are using multiple input options. If you purchased a printer with a similar configuration, then you may need additional furniture.
Using MS810de 82 The following illustration shows the maximum number of optional finishers and trays that are supported by the printer. For more information on other configurations, visit www.lexmark.com/multifunctionprinters.
Using MS810de 83 The staple, hole punch finisher must not be combined with any other output options. • In a configuration with three optional finishers, the output expander and mailbox may be installed in any order. • In a configuration with two optional finishers: – The staple finisher must always be on top. – The high‑capacity output expander must always be at the bottom. – The output expander is the only option that can be placed on top of the high‑capacity output expander.
Using MS810de 84 7 Use the To USB port Connect a flash drive to the printer. Note: Only the front USB port supports flash drives. Understanding the colors of the Sleep button and indicator lights The colors of the Sleep button and indicator lights on the printer control panel signify a certain printer status or condition. Indicator light Printer status Off The printer is off or in Hibernate mode. Blinking green The printer is warming up, processing data, or printing.
Using MS810de Touch 85 To 1 Change Language Change the primary language of the printer. 2 Bookmarks Create, organize, and save a set of bookmarks (URLs) into a tree view of folders and file links. Note: The tree view does not include bookmarks created within Forms and Favorites, and the ones in the tree are not usable in Forms and Favorites. 3 Held Jobs Display all current held jobs. 4 USB View, select, or print photos and documents from a flash drive.
Using MS810de 86 Using the touch-screen buttons Note: Your home screen may vary, depending on your home screen customization settings, administrative setup, and active embedded solutions. 2 1 5 Touch the To 1 Radio button Select or clear an item. 2 Up arrow Scroll up. 3 Down arrow Scroll down. 4 Accept button Save a setting. 5 Cancel button Touch 4 3 • Cancel an action or a selection. • Return to the previous screen. To Return to the home screen.
Using MS810de 87 Setting up and using the home screen applications Notes: • Your home screen may vary depending on your home screen customization settings, administrative setup, and active embedded applications. Some applications are supported only in some printer models. • There may be additional solutions and applications available for purchase. For more information, go to www.lexmark.com or contact the place where you purchased the printer.
Using MS810de 88 Customizing the home screen 1 Open a Web browser, and then type the printer IP address in the address field. Note: View the printer IP address on the printer home screen. The IP address appears as four sets of numbers separated by periods, such as 123.123.123.123. 2 Do one or more of the following: • Show or hide the icons of basic printer functions. a Click Settings > General Settings > Home screen customization. b Select the check boxes to specify which icons appear on the home screen.
Using MS810de 89 Setting up Forms and Favorites Note: A later version of this User's Guide may contain a direct link to the Administrator’s Guide of this application. To check for updates of this User’s Guide, go to http://support.lexmark.com. Use To Streamline work processes by letting you quickly find and print frequently used online forms directly from the printer home screen. Note: The printer must have permission to access the network folder, FTP site, or Web site where the bookmark is stored.
Using MS810de 90 Exporting and importing a configuration You can export configuration settings into a text file, and then import the file to apply the settings to other printers. 1 Open a Web browser, and then type the printer IP address in the address field. Note: View the printer IP address on the printer home screen. The IP address appears as four sets of numbers separated by periods, such as 123.123.123.123.
Using MS810de 91 3 Select the Enable check box, and then customize the settings. 4 Click Submit. To use the application, click Remote Operator Panel > Launch VNC Applet. Loading paper and specialty media The selection and handling of paper and specialty media can affect how reliably documents print. For more information, see “Avoiding jams” on page 260 and “Storing paper” on page 179.
Using MS810de 92 • Do not remove trays while a job prints or while Busy appears on the display. Doing so may cause a jam. 2 Squeeze and slide the width guide to the correct position for the size of the paper being loaded until it clicks into place. Note: Use the paper size indicators at the bottom of the tray to help position the guides.
Using MS810de 93 3 Unlock the length guide, and then squeeze and slide the guide to the correct position for the size of the paper being loaded. Notes: • Lock the length guide for all paper sizes. • Use the paper size indicators at the bottom of the tray to help position the guides.
Using MS810de 94 4 Flex the sheets back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface. 5 Load the paper stack with the printable side facedown. Note: Make sure the paper or envelope is loaded properly. • There are different ways of loading letterhead depending on whether an optional staple finisher is installed or not.
Using MS810de 95 Without an optional staple finisher With an optional staple finisher C AB AB C Two‑sided printing Two‑sided printing • If you are loading prepunched paper for use with the staple finisher, then make sure the holes on the long edge of the paper are on the right side of the tray. One‑sided printing Two‑sided printing AB C Note: If the holes on the long edge of the paper are on the left side of the tray, then a jam may occur. • Do not slide the paper into the tray.
Using MS810de 96 • If you are loading envelopes, then make sure that the flap side is facing up and the envelopes are on the left side of the tray. • Make sure the paper is below the solid line, which is the maximum paper fill indicator. Warning—Potential Damage: Overfilling the tray can cause paper jams.
Using MS810de 97 • When using card stock, labels, or other types of specialty media, make sure the paper is below the dashed line, which is the alternate paper fill indicator. 6 For custom‑ or Universal‑size paper, adjust the paper guides to lightly touch the sides of the stack, and then lock the length guide. 7 Insert the tray. 8 From the printer control panel, set the paper size and paper type in the Paper menu to match the paper loaded in the tray.
Using MS810de 98 Loading the 2100‑sheet tray CAUTION—POTENTIAL INJURY: To reduce the risk of equipment instability, load each tray separately. Keep all other trays closed until needed. 1 Pull out the tray. 2 Adjust the width and length guides. Loading A5‑size paper a Pull up and slide the width guide to the position for A5.
Using MS810de 99 b Squeeze and slide the length guide to the position for A5 until it clicks into place. 2 1 c Remove the A5 length guide from its holder. 1 d Insert the A5 length guide into its designated slot. Note: Press the A5 length guide until it clicks into place.
Using MS810de 100 Loading A4‑, letter‑, legal‑, Oficio‑, and Folio‑size paper a Pull up and slide the width guide to the correct position for the size of the paper being loaded.
Using MS810de 101 b If the A5 length guide is still attached to the length guide, then remove it from its place. If the A5 length guide is not attached, then proceed to step d. c Put the A5 length guide in its holder.
Using MS810de 102 d Squeeze the length guide and slide it to the correct position for the size of the paper being loaded until it clicks into place. 3 Flex sheets of paper back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface. 4 Load the paper stack with the printable side facedown. Note: Make sure the paper is loaded properly.
Using MS810de 103 Without an optional staple finisher With an optional staple finisher C One‑sided printing AB C AB One‑sided printing C C Two‑sided printing AB AB Two‑sided printing • If you are loading prepunched paper for use with the staple finisher, then make sure the holes on the long edge of the paper are on the right side of the tray.
Using MS810de • Make sure the paper is below the maximum paper fill indicator. Warning—Potential Damage: Overfilling the tray can cause paper jams. 5 Insert the tray. Note: Press the paper stack down while inserting the tray.
Using MS810de 105 6 From the printer control panel, set the paper size and type in the Paper menu to match the paper loaded in the tray. Note: Set the correct paper size and type to avoid paper jams and print quality problems. Loading the multipurpose feeder 1 Pull down the multipurpose feeder door. Note: Do not load or close the multipurpose feeder while a job is printing.
Using MS810de 106 2 Pull the multipurpose feeder extender. LTR A4 A5 EX B5 EC Note: Guide the extender gently so that the multipurpose feeder is fully extended and open. 3 Slide the width guide to the correct position for the size of the paper being loaded. LT R A4 A5 EX EC B 5 Note: Use the paper size indicators on the bottom of tray to help position the guides.
Using MS810de 107 LT R A 4 A 5 C E X E B 5 4 Prepare the paper or specialty media for loading. • Flex sheets of paper back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface. • Hold transparencies by the edges, and then fan them. Straighten the edges on a level surface. Note: Avoid touching the printable side of the transparencies. Be careful not to scratch them.
Using MS810de 108 • There are different ways of loading letterhead depending on whether an optional staple finisher is installed or not. A A B C B C Without an optional staple finisher With an optional staple finisher One‑sided printing A B C One‑sided printing Two‑sided printing Two‑sided printing • If you are loading prepunched paper for use with the staple finisher, then make sure the holes on the long edge of the paper are on the right side of the tray.
Using MS810de 109 5 4 A B C E X E A 5 R T L • Load envelopes with the flap side down and on the left of the multipurpose feeder. Warning—Potential Damage: Never use envelopes with stamps, clasps, snaps, windows, coated linings, or self‑stick adhesives. These envelopes may severely damage the printer. • Make sure the paper or specialty media is below the maximum paper fill indicator. Warning—Potential Damage: Overfilling the feeder can cause paper jams.
Using MS810de 110 Linking and unlinking trays Linking and unlinking trays 1 Open a Web browser, and then type the printer IP address in the address field. Notes: • View the printer IP address on the printer home screen. The IP address appears as four sets of numbers separated by periods, such as 123.123.123.123. • If you are using a proxy server, then temporarily disable it to load the Web page correctly. 2 Click Settings > Paper Menu.
Using MS810de 3 Touch 111 . 4 Touch Custom Types, and then verify that the new custom paper type name has replaced the custom name. Assigning a custom paper type Using the Embedded Web Server Assign a custom paper type name to a tray when linking or unlinking trays. 1 Open a Web browser, and then type the printer IP address in the address field. Notes: • View the printer IP address on the printer home screen. The IP address appears as four sets of numbers separated by periods, such as 123.123.123.
Using MS810de 112 Printing a document 1 From the Paper menu on the printer control panel, set the paper type and size to match the paper loaded. 2 Send the print job: For Windows users a b c d With a document open, click File > Print. Click Properties, Preferences, Options, or Setup. Adjust the settings, if necessary. Click OK > Print. For Macintosh users a Customize the settings in the Page Setup dialog: 1 With a document open, choose File > Page Setup.
Using MS810de 113 Printing from a flash drive or mobile device Printing from a flash drive Notes: • Before printing an encrypted PDF file, you will be prompted to type the file password from the printer control panel. • You cannot print files for which you do not have printing permissions. 1 Insert a flash drive into the USB port. Notes: • A flash drive icon appears on the printer home screen when a flash drive is inserted.
Using MS810de 114 2 From the printer control panel, touch the document you want to print. 3 Touch the arrows to specify the number of copies for printing, and then touch Print. Notes: • Do not remove the flash drive from the USB port until the document has finished printing. • If you leave the flash drive in the printer after leaving the initial USB menu screen, then touch Held Jobs on the home screen to print files from the flash drive.
Using MS810de 115 Recommended flash drives File type • Lexar JumpDrive FireFly (512MB and 1GB) • SanDisk Cruzer Micro (512MB and 1GB) • Sony Micro Vault Classic (512MB and 1GB) Documents: • .pdf • .xps Images: • • • • • • • • .dcx .gif .jpeg or .jpg .bmp .pcx .tiff or .tif .png .
Using MS810de 2 Touch 116 . Printing confidential and other held jobs Note: Confidential and Verify print jobs are automatically deleted from memory after printing. Repeat and Reserve jobs are held in the printer until you delete them. For Windows users 1 With a document open, click File > Print. 2 Click Properties, Preferences, Options, or Setup. 3 Click Print and Hold. 4 Select the print job type (Confidential, Repeat, Reserve, or Verify), and then assign a user name.
Using MS810de 117 Printing a directory list A directory list shows the resources stored in a flash memory or in the printer hard disk. From the home screen, navigate to: > Reports > Print Directory Canceling a print job Canceling a print job from the printer control panel 1 From the home screen, touch Cancel Jobs, or press 2 Touch the job you want to cancel, and then touch 3 Press on the keypad. . on the keypad to return to the home screen.
Using MS810de 118 • If you are using a proxy server, then temporarily disable it to load the Web page correctly. 2 Check the virtual display that appears at the top left corner of the screen. The virtual display works as an actual display would work on a printer control panel. Configuring supply notifications from the Embedded Web Server You can determine how you would like to be notified when supplies run nearly low, low, very low, or reach their end‑of‑life by setting the selectable alerts.
Using MS810de 119 Notes: • View the printer IP address on the printer home screen. The IP address appears as four sets of numbers separated by periods, such as 123.123.123.123. • If you are using a proxy server, then temporarily disable it to load the Web page correctly. 2 Click Settings > Security > Confidential Print Setup. 3 Modify the settings: • Set a maximum number of PIN entry attempts. When a user exceeds that number, all of the jobs for that user are deleted.
Using MS810de 120 Printing a network setup page If the printer is attached to a network, then print a network setup page to verify the network connection. This page also provides important information that aids network printing configuration. 1 From the home screen, navigate to: > Reports > Network Setup Page 2 Check the first section of the network setup page and confirm that the status is Connected.
Using MS810de 121 3 Select a setting. Use To Off Use the factory default settings for all settings associated with Eco‑Mode. Notes: • Settings that were changed when other modes were selected are reset to the factory default settings. • Off supports the performance specifications of the printer. Energy Reduce energy use, especially when the printer is idle. Notes: • Printer engine motors do not start until a document is ready to print. You may notice a short delay before the first page is printed.
Using MS810de 122 Use To On Reduce printer noise. Notes: • Print jobs process at a reduced speed. • Printer engine motors do not start until a document is ready to print. There is a short delay before the first page is printed. • The alarm control and cartridge alarm sounds are turned off. • The printer ignores the Advance Start command. Off Use factory default settings. Note: This setting supports the performance specifications of the printer. 4 Click Submit.
Using MS810de 123 If you want a more comprehensive method of restoring the printer factory default settings, then perform the Wipe All Settings option. For more information, see “Erasing non‑volatile memory” on page 124. Warning—Potential Damage: Restoring factory defaults returns most printer settings to the original factory default settings. Exceptions include the display language, custom sizes and messages, and network/port menu settings. All downloads stored in the RAM are deleted.
Using MS810de 124 Type of memory Description Hard disk memory Some printers have a hard disk drive installed. The printer hard disk is designed for device-specific functionality. This lets the device retain buffered user data from complex print jobs, as well as form data, and font data. Erase the content of any installed printer memory in the following circumstances: • • • • • • The printer is being decommissioned. The printer hard disk is being replaced.
Using MS810de 125 The printer will perform a power‑on reset, and then return to normal operating mode. Erasing printer hard disk memory Notes: • Some printer models may not have a printer hard disk installed. • Configuring Erase Temporary Data Files in the printer menus lets you remove residual confidential material left by print jobs by securely overwriting files that have been marked for deletion. Using the printer control panel 1 Turn off the printer.
Using MS810de 126 • If you are using a proxy server, then temporarily disable it to load the Web page correctly. 2 Click Settings > Security > Disk Encryption. Note: Disk Encryption appears in the Security Menu only when a formatted, non‑defective printer hard disk is installed. 3 From the Disk encryption menu, select Enable. Notes: • Enabling disk encryption will erase the contents of the printer hard disk.
Using MS812de 127 Using MS812de Learning about the printer Printer configurations Basic model 1 Standard bin 2 Printer control panel 3 Multipurpose feeder 4 Standard 550‑sheet tray (Tray 1) Fully configured model CAUTION—TIPPING HAZARD: Floor-mounted configurations require additional furniture for stability. You must use either a printer stand or printer base if you are using multiple input options. If you purchased a printer with a similar configuration, then you may need additional furniture.
Using MS812de 128 The following illustration shows the maximum number of optional finishers and trays that are supported by the printer. For more information on other configurations, visit www.lexmark.com/multifunctionprinters.
Using MS812de 129 The staple, hole punch finisher must not be combined with any other output options. • In a configuration with three optional finishers, the output expander and mailbox may be installed in any order. • In a configuration with two optional finishers: – The staple finisher must always be on top. – The high‑capacity output expander must always be at the bottom. – The output expander is the only option that can be placed on top of the high‑capacity output expander.
Using MS812de 130 7 Use the To USB port Connect a USB Bluetooth adapter or a flash drive to the printer. Note: Only the front USB port supports flash drives. Understanding the colors of the Sleep button and indicator lights The colors of the Sleep button and indicator lights on the printer control panel signify a certain printer status or condition. Indicator light Printer status Off The printer is off or in Hibernate mode. Blinking green The printer is warming up, processing data, or printing.
Using MS812de 131 Touch To 1 Search Held Jobs Search current held jobs. 2 Held Jobs Display all current held jobs. 3 Forms and Favorites Access frequently used online forms. 4 Eco‑Settings Adjust energy consumption, noise, toner and paper usage. 5 Menus Access printer menus. Note: These menus are available only when the printer is in Ready state. 6 Status message bar • Show the current printer status such as Ready or Busy.
Using MS812de 132 2 1 8 Touch To 1 Left arrow Scroll to the left. 2 Right arrow Scroll to the right. 3 Up arrow 4 Down arrow Scroll down. 5 Submit Submit changes made in the printer settings. 6 Back Return to the previous screen. 7 Home Return to the home screen. Scroll up.
Using MS812de 8 133 Touch To Tips Open a context-sensitive Help dialog on the printer control panel. Other touch-screen buttons Touch To Accept Save settings. Cancel • Cancel an action or a selection. • Leave a screen and return to the previous screen without saving changes. Increase Select a higher value. Decrease Select a lower value. Exit Leave the current screen. Search Search current held jobs. Warning View a warning or error message.
Using MS812de 134 Setting up and using the home screen applications Notes: • Your home screen may vary depending on your home screen customization settings, administrative setup, and active embedded applications. Some applications are supported only in some printer models. • There may be additional solutions and applications available for purchase. For more information, go to www.lexmark.com or contact the place where you purchased the printer.
Using MS812de 135 Customizing the home screen 1 Open a Web browser, and then type the printer IP address in the address field. Note: View the printer IP address on the printer home screen. The IP address appears as four sets of numbers separated by periods, such as 123.123.123.123. 2 Do one or more of the following: • Show or hide icons of basic printer functions. a Click Settings > General Settings > Home screen customization.
Using MS812de 136 Setting up Forms and Favorites Note: A later version of this User's Guide may contain a direct link to the Administrator’s Guide of this application. To check for updates of this User’s Guide, visit http://support.lexmark.com. Use To Quickly find and print frequently used online forms directly from the printer home screen. Note: The printer must have permission to access the network folder, FTP site, or Web site where the bookmark is stored.
Using MS812de 137 Exporting and importing a configuration You can export configuration settings into a text file, and then import the file to apply the settings to other printers. 1 Open a Web browser, and then type the printer IP address in the address field. Note: View the printer IP address on the printer home screen. The IP address appears as four sets of numbers separated by periods, such as 123.123.123.123.
Using MS812de 138 3 Select the Enable check box, and then customize the settings. 4 Click Submit. To use the application, click Remote Operator Panel > Launch VNC Applet. Loading paper and specialty media The selection and handling of paper and specialty media can affect how reliably documents print. For more information, see “Avoiding jams” on page 260 and “Storing paper” on page 179.
Using MS812de 139 Loading the 250‑ or 550‑sheet tray CAUTION—POTENTIAL INJURY: To reduce the risk of equipment instability, load each tray separately. Keep all other trays closed until needed. 1 Pull out the tray. Notes: • When loading folio‑, legal‑, or Oficio‑size paper, lift the tray slightly and then pull it out completely. • Do not remove trays while a job prints or while Busy appears on the display. Doing so may cause a jam.
Using MS812de 140 2 Squeeze and slide the width guide to the correct position for the size of the paper being loaded until it clicks into place. Note: Use the paper size indicators at the bottom of the tray to help position the guides.
Using MS812de 141 3 Unlock the length guide, and then squeeze and slide the guide to the correct position for the size of the paper being loaded. Notes: • Lock the length guide for all paper sizes. • Use the paper size indicators at the bottom of the tray to help position the guides.
Using MS812de 142 4 Flex the sheets back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface. 5 Load the paper stack with the printable side facedown. Note: Make sure the paper or envelope is loaded properly. • There are different ways of loading letterhead depending on whether an optional staple finisher is installed or not.
Using MS812de 143 • Do not slide the paper into the tray. Load paper as shown in the illustration. • If you are loading envelopes, then make sure that the flap side is facing up and the envelopes are on the left side of the tray.
Using MS812de • Make sure the paper is below the solid line, which is the maximum paper fill indicator. Warning—Potential Damage: Overfilling the tray can cause paper jams.
Using MS812de 145 • When using card stock, labels, or other types of specialty media, make sure the paper is below the dashed line, which is the alternate paper fill indicator. 6 For custom‑ or Universal‑size paper, adjust the paper guides to lightly touch the sides of the stack, and then lock the length guide. 7 Insert the tray. 8 From the printer control panel, set the paper size and paper type in the Paper menu to match the paper loaded in the tray.
Using MS812de 146 Loading the 2100‑sheet tray CAUTION—POTENTIAL INJURY: To reduce the risk of equipment instability, load each tray separately. Keep all other trays closed until needed. 1 Pull out the tray. 2 Adjust the width and length guides. Loading A5‑size paper a Pull up and slide the width guide to the position for A5.
Using MS812de 147 b Squeeze and slide the length guide to the position for A5 until it clicks into place. 2 1 c Remove the A5 length guide from its holder. 1 d Insert the A5 length guide into its designated slot. Note: Press the A5 length guide until it clicks into place.
Using MS812de 148 Loading A4‑, letter‑, legal‑, oficio‑, and folio‑size paper a Pull up and slide the width guide to the correct position for the size of the paper being loaded.
Using MS812de 149 b If the A5 length guide is still attached to the length guide, then remove it from its place. If the A5 length guide is not attached, then proceed to step d. c Put the A5 length guide in its holder.
Using MS812de 150 d Squeeze the length guide and slide it to the correct position for the size of the paper being loaded until it clicks into place. 3 Flex sheets of paper back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface. 4 Load the paper stack with the printable side facedown. Note: Make sure the paper is loaded properly.
Using MS812de 151 Without an optional staple finisher With an optional staple finisher C One‑sided printing AB C AB One‑sided printing C C Two‑sided printing AB AB Two‑sided printing • If you are loading prepunched paper for use with the staple finisher, then make sure the holes on the long edge of the paper are on the right side of the tray.
Using MS812de • Make sure the paper is below the maximum paper fill indicator. Warning—Potential Damage: Overfilling the tray can cause paper jams. 5 Insert the tray. Note: Press the paper stack down while inserting the tray.
Using MS812de 153 6 From the printer control panel, set the paper size and type in the Paper menu to match the paper loaded. Note: Set the correct paper size and type to avoid paper jams and print quality problems. Loading the multipurpose feeder 1 Pull down the multipurpose feeder door. Note: Do not load or close the multipurpose feeder while a job is printing.
Using MS812de 154 2 Using the handle, pull the multipurpose feeder extender. LTR A4 A5 EX B5 EC Note: Guide the extender gently so that the multipurpose feeder is fully extended and open. 3 Slide the width guide to the correct position for the size of the paper being loaded. LT R A4 A5 EX EC B 5 Note: Use the paper size indicators on the bottom of tray to help position the guides.
Using MS812de 155 LT R A 4 A 5 C E X E B 5 4 Prepare the paper or specialty media for loading. • Flex sheets of paper back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface. • Hold transparencies by the edges, and then fan them. Straighten the edges on a level surface. Note: Avoid touching the printable side of the transparencies. Be careful not to scratch them.
Using MS812de 156 • There are different ways of loading letterhead depending on whether an optional staple finisher is installed or not. A A B C B C Without an optional staple finisher With an optional staple finisher One‑sided printing A B C One‑sided printing Two‑sided printing Two‑sided printing • If you are loading prepunched paper for use with the staple finisher, then make sure the holes on the long edge of the paper are on the right side of the tray.
Using MS812de 157 5 4 A B C E X E A 5 R T L • Load envelopes with the flap side down and on the left of the multipurpose feeder. Warning—Potential Damage: Never use envelopes with stamps, clasps, snaps, windows, coated linings, or self‑stick adhesives. These envelopes may severely damage the printer. • Make sure the paper or specialty media is below the maximum paper fill indicator. Warning—Potential Damage: Overfilling the feeder can cause paper jams.
Using MS812de 158 Linking and unlinking trays Linking and unlinking trays 1 Open a Web browser, and then type the printer IP address in the address field. Notes: • View the printer IP address on the printer home screen. The IP address appears as four sets of numbers separated by periods, such as 123.123.123.123. • If you are using a proxy server, then temporarily disable it to load the Web page correctly. 2 Click Settings > Paper Menu.
Using MS812de 159 3 Touch Submit. 4 Touch Custom Types, and then verify if the new custom paper type name has replaced the custom name. Assigning a custom paper type Using the Embedded Web Server Assign a custom paper type name to a tray when linking or unlinking trays. 1 Open a Web browser, and then type the printer IP address in the address field. Notes: • View the printer IP address on the printer home screen. The IP address appears as four sets of numbers separated by periods, such as 123.123.123.
Using MS812de Printing a document 1 From the printer control panel, set the paper type and size to match the paper loaded. 2 Send the print job: For Windows users a b c d With a document open, click File > Print. Click Properties, Preferences, Options, or Setup. Adjust the settings, if necessary. Click OK > Print. For Macintosh users a Customize the settings in the Page Setup dialog: 1 With a document open, choose File > Page Setup.
Using MS812de 161 Printing from a flash drive or mobile device Printing from a flash drive Notes: • Before printing an encrypted PDF file, you will be prompted to type the file password from the printer control panel. • You cannot print files for which you do not have printing permissions. 1 Insert a flash drive into the USB port. Notes: • A flash drive icon appears on the printer home screen when a flash drive is inserted.
Using MS812de 162 2 From the printer control panel, touch the document you want to print. 3 Touch the arrows to specify the number of copies for printing, and then touch Print. Notes: • Do not remove the flash drive from the USB port until the document has finished printing. • If you leave the flash drive in the printer after leaving the initial USB menu screen, then touch Held Jobs on the home screen to print files from the flash drive.
Using MS812de 163 Recommended flash drives File type • Lexar JumpDrive FireFly (512MB and 1GB) • SanDisk Cruzer Micro (512MB and 1GB) • Sony Micro Vault Classic (512MB and 1GB) Documents: • .pdf • .xps Images: • • • • • • • • .dcx .gif .jpeg or .jpg .bmp .pcx .tiff or .tif .png .
Using MS812de 164 Printing confidential and other held jobs Note: Confidential and Verify print jobs are automatically deleted from memory after printing. Repeat and Reserve jobs are held in the printer until you delete them. For Windows users 1 With a document open, click File > Print. 2 Click Properties, Preferences, Options, or Setup. 3 Click Print and Hold. 4 Select the print job type (Confidential, Repeat, Reserve, or Verify), and then assign a user name.
Using MS812de 165 Printing a directory list A directory list shows the resources stored in a flash memory or in the printer hard disk. From the home screen, navigate to: > Reports > Print Directory Canceling a print job Canceling a print job from the printer control panel 1 From the printer control panel, touch Cancel Job or press on the keypad. 2 Touch the print job you want to cancel, and then touch Delete Selected Jobs.
Using MS812de 166 • If you are using a proxy server, then temporarily disable it to load the Web page correctly. 2 Check the virtual display that appears in the top left corner of the screen. The virtual display works as an actual display would work on a printer control panel. Configuring supply notifications from the Embedded Web Server You can determine how you would like to be notified when supplies run nearly low, low, very low, or reach their end‑of‑life by setting the selectable alerts.
Using MS812de 167 Notes: • View the printer IP address on the printer home screen. The IP address appears as four sets of numbers separated by periods, such as 123.123.123.123. • If you are using a proxy server, then temporarily disable it to load the Web page correctly. 2 Click Settings > Security > Confidential Print Setup. 3 Modify the settings: • Set a maximum number of PIN entry attempts. When a user exceeds that number, all of the jobs for that user are deleted.
Using MS812de 168 Printing a network setup page If the printer is attached to a network, then print a network setup page to verify the network connection. This page also provides important information that aids network printing configuration. 1 From the home screen, navigate to: > Reports > Network Setup Page 2 Check the first section of the network setup page and confirm that the status is Connected.
Using MS812de 169 • If you are using a proxy server, then temporarily disable it to load the Web page correctly. 2 Click Settings > General Settings > Eco‑Mode. 3 Select a setting. Use To Off Use the factory default settings for all settings associated with Eco‑Mode. Notes: • Settings that were changed when other modes were selected are reset to the factory default settings. • Off supports the performance specifications of the printer. Energy Reduce energy use, especially when the printer is idle.
Using MS812de 170 Use To On Reduce printer noise. Notes: • Print jobs process at a reduced speed. • Printer engine motors do not start until a document is ready to print. There is a short delay before the first page is printed. • The alarm control and cartridge alarm sounds are turned off. • The printer will ignore the Advance Start command. Off Use factory default settings. Note: This setting supports the performance specifications of the printer. 4 Click Submit.
Using MS812de 171 Warning—Potential Damage: Restoring factory defaults returns most printer settings to the original factory default settings. Exceptions include the display language, custom sizes and messages, and network/port menu settings. All downloads stored in the RAM are deleted. Downloads stored in the flash memory or in a printer hard disk are not affected.
Using MS812de 172 Erase the content of any installed printer memory in the following circumstances: • • • • • • The printer is being decommissioned. The printer hard disk is being replaced. The printer is being moved to a different department or location. The printer is being serviced by someone from outside your organization. The printer is being removed from your premises for service. The printer is being sold to another organization.
Using MS812de 173 Erasing printer hard disk memory Notes: • Some printer models may not have a printer hard disk installed. • Configuring Erase Temporary Data Files in the printer menus lets you remove residual confidential material left by print jobs by securely overwriting files that have been marked for deletion. Using the printer control panel 1 Turn off the printer. 2 Hold down 2 and 6 while turning the printer on. Release the buttons only when the screen with the progress bar appears.
Using MS812de 174 Notes: • Enabling disk encryption will erase the contents of the printer hard disk. • Disk encryption can take from several minutes to more than an hour, during which the printer will be unavailable for other user tasks. 4 Click Submit. Using the printer control panel 1 Turn off the printer. 2 Hold down 2 and 6 while turning the printer on. Release the buttons only when the screen with the progress bar appears.
Paper and specialty media guide 175 Paper and specialty media guide Notes: • • • • Make sure that the paper size, type, and weight are set correctly on the computer or control panel. Flex, fan, and straighten specialty media before loading them. The printer may print at a reduced speed to prevent damage to the fuser. For more information on card stock and labels, see the Card Stock & Label Guide on the Lexmark support Web site at http://support.lexmark.com.
Paper and specialty media guide 176 – Have bent corners. – Have rough, cockle, or laid finishes. • Adjust the width guides to fit the width of the envelopes. • Before loading the envelopes on the tray, flex the stack of envelopes back and forth to loosen them, and then fan them. Straighten the edges on a level surface. Note: A combination of high humidity (over 60%) and high printing temperature may wrinkle or seal envelopes.
Paper and specialty media guide 177 Weight The printer trays and multipurpose feeder can automatically feed paper weights between 60–176 g/m2 (16–47‑lb) grain long paper. The 2100‑sheet tray can automatically feed paper weights up to 60–135 g/m2 (16–36‑lb) grain long paper. Paper lighter than 60 g/m2 (16 lb) might not be stiff enough to feed properly, and may cause jams. Note: Two‑sided printing is supported for 60–176 g/m2 (16–47‑lb) paper. Curl Curl is the tendency for paper to curl at its edges.
Paper and specialty media guide 178 • Do not mix paper sizes, types, or weights in the same tray; mixing results in jams. • Do not use coated papers unless they are specifically designed for electrophotographic printing. Selecting preprinted forms and letterhead • • • • Use grain long for 60–90‑g/m2 (16–24‑lb) paper. Use only forms and letterhead printed using an offset lithographic or engraved printing process. Avoid paper with rough or heavily textured surfaces.
Paper and specialty media guide 179 customers minimize printing and copying waste. In addition, the company encourages purchasing paper from suppliers who demonstrate their commitment to sustainable forestry practices. Lexmark does not endorse specific suppliers, although a converter’s product list for special applications is maintained. However, the following paper choice guidelines will help alleviate the environmental impact of printing: 1 Minimize paper consumption.
Paper and specialty media guide 180 Supported paper sizes, types, and weights The following tables provide information on standard and optional paper sources and the sizes, types, and weights of paper they support. Note: For an unlisted paper size, select the closest larger listed size. Paper types and weights supported by the printer The printer engine supports 60–176‑g/m2 (16–47‑lb) paper weights.
Paper and specialty media guide Paper size1 Dimensions JIS B5 182 x 257 mm (7.2 x 10.1 in.) Letter 216 x 279 mm (8.5 x 11 in.) Legal 216 x 356 mm (8.5 x 14 in.) Executive 184 x 267 mm (7.3 x 10.5 in.) Oficio 216 x 340 mm (8.5 x 13.4 in.) Folio 216 x 330 mm (8.5 x 13 in.) Statement 140 x 216 mm (5.5 x 8.5 in.) Universal3 105 x 148 mm to 216 x 356 mm (4.13 x 5.83 in. to 8.5 x 14 in.) 70 x 127 mm to 216 x 356 mm (2.76 x 5 to 8.5 x 14 in.
Paper and specialty media guide 182 Paper size1 Dimensions Other Envelope 98 x 162 mm (3.9 x 6.4 in.) to 176 x 250 mm (6.9 x 9.8 in.) Standard or Optional optional 250‑ or 2100‑sheet tray 550‑sheet tray Multipurpose feeder Duplex X X 1 If your preferred default paper size cannot be set in the printer control panel, then you may select common paper sizes that correspond to the position of the length guide in the tray from the Paper Size/Type menu.
Paper and specialty media guide 183 Supported paper types and weights Paper type Plain Paper Paper weight 90–176 g/m2 (24–47 lb bond) 4‑bin mailbox Output expander and high‑capacity output expander X Staple finisher Staple, hole punch finisher X X 60–90 g/m2 (16–24 lb bond) Card Stock 163 g/m2 (90 Ib index) 199 g/m2 (110 Ib index) Transparency2 146 g/m2 (39 Ib bond) Recycled 90–176 g/m2 (24–47 lb bond) X X 1 X X 1 X 1 1 X X X X X X X X X X X X X X X X X X X X X
Paper and specialty media guide Paper type Preprinted Paper weight 90–176 g/m2 (24–47 lb bond) 184 4‑bin mailbox Output expander and high‑capacity output expander Staple finisher Staple, hole punch finisher X X X X X X X X X X X X X X X X X X 60–90 g/m2 (16–24 lb bond) Colored Paper 90–176 g/m2 (24–47 lb bond) 60–90 g/m2 (16–24 lb bond) Light paper 90–176 g/m2 (24–47 lb bond) 60–90 g/m2 (16–24 lb bond) Heavy paper 90–176 g/m2 (24–47 lb bond) 60–90 g/m2 (16–24 lb bond) Rough
Understanding the printer menus 185 Understanding the printer menus Menus list Paper Menu Reports Network/Ports Default Source Paper Size/Type Menu Settings Page Device Statistics Active NIC Configure MP Stapler Test Standard USB Substitute Size Paper Texture Network Setup Page1 Profiles List Parallel [x] Serial [x] Paper Weight Print Fonts SMTP Setup Paper Loading Print Directory Custom Types Asset Report Custom Standard Network2 Names3 Custom Bin Names3 Universal Setup Bin Setup Se
Understanding the printer menus 186 Paper menu Vinyl label is supported only in MS710 Series printer models. Default Source menu Use To Default Source Tray [x] Set a default paper source for all print jobs. Multipurpose Feeder1 MP Feeder2 Manual Paper Manual Envelope Notes: • Tray 1 (standard tray) is the factory default setting. • From the Paper menu, set Configure MP to "Cassette" for Multipurpose Feeder or MP Feeder to appear as a menu setting.
Understanding the printer menus 187 Use To Tray [x] Type Plain Paper Card Stock Transparency Recycled Labels Bond Envelope Rough Envelope Letterhead Preprinted Colored Paper Light Paper Heavy Paper Rough/Cotton Custom Type [x] Specify the paper type loaded in each tray.
Understanding the printer menus 188 Use To MP Feeder Type Plain Paper Card Stock Transparency Recycled Labels Bond Envelope Rough Envelope Letterhead Preprinted Colored Paper Light Paper Heavy Paper Rough/Cotton Custom Type [x] Specify the paper type loaded in the multipurpose feeder. Manual Paper Size A4 A5 A6 JIS B5 Letter Legal Executive Oficio (Mexico) Folio Statement Universal Specify the paper size being manually loaded.
Understanding the printer menus 189 Use To Manual Envelope Size 7 3/4 Envelope 9 Envelope 10 Envelope DL Envelope C5 Envelope B5 Envelope Other Envelope Specify the envelope size being manually loaded. Manual Envelope Type Envelope Rough Envelope Custom Type [x] Specify the envelope type being manually loaded. Note: 10 Envelope is the U.S. factory default setting. DL Envelope is the international factory default setting. Note: Envelope is the factory default setting.
Understanding the printer menus Paper Texture menu Use To Plain Texture Smooth Normal Rough Specify the relative texture of the plain paper loaded in a specific tray. Card Stock Texture Smooth Normal Rough Specify the relative texture of the card stock loaded in a specific tray. Transparency Texture Smooth Normal Rough Specify the relative texture of the transparencies loaded in a specific tray.
Understanding the printer menus 191 Use To Preprinted Texture Smooth Normal Rough Specify the relative texture of the preprinted paper loaded in a specific tray. Colored Texture Smooth Normal Rough Specify the relative texture of the colored paper loaded in a specific tray. Light Texture Smooth Normal Rough Specify the relative texture of the light paper loaded in a specific tray. Heavy Texture Smooth Normal Rough Specify the relative texture of the heavy paper loaded in a specific tray.
Understanding the printer menus 192 Use To Labels Weight Light Normal Heavy Specify the relative weight of the labels loaded. Vinyl Labels Weight Light Normal Heavy Specify the relative weight of the vinyl labels loaded. Bond Weight Light Normal Heavy Specify the relative weight of the bond paper loaded. Envelope Weight Light Normal Heavy Specify the relative weight of the envelope loaded. Rough Envelope Weight Light Normal Heavy Specify the relative weight of the rough envelope loaded.
Understanding the printer menus 193 Use To Custom [x] Weight Light Normal Heavy Specify the relative weight of the custom paper loaded. Notes: • Normal is the factory default setting. • The options appear only when the custom type is supported. Paper Loading menu Use To Card Stock Loading Duplex Off Determine and set two-sided printing for all print jobs with Card Stock as the paper type.
Understanding the printer menus 194 Use To Heavy Loading Duplex Off Determine and set two-sided printing for all print jobs with Heavy as the paper type. Rough/Cotton Loading Duplex Off Determine and set two-sided printing for all print jobs with Rough or Cotton as the paper type. Custom [x] Loading Duplex Off Determine and set two-sided printing for all print jobs with Custom [x] as the paper type. Note: Custom [x] Loading is available only when the custom type is supported.
Understanding the printer menus 195 Custom Bin Names menu Note: This menu appears only in touch‑screen printer models. Use To Standard Bin Specify a custom name for the standard bin. Bin [x] Specify a custom name for Bin [x]. Universal Setup menu Use To Units of Measure Inches Millimeters Identify the units of measure. Portrait Width 3–14.17 inches 76–360 mm Set the portrait width. Notes: • Inches is the U.S. factory default setting. • Millimeters is the international factory default setting.
Understanding the printer menus 196 Bin Setup menu Use To Output Bin Standard Bin Bin [x] Specify the default bin. Notes: • If multiple bins are assigned the same name, then the name appears only once in the menu. • Standard Bin is the factory default setting. Configure Bins Mailbox Link Mail Overflow Link Optional Type Assignment Specify configuration options for bins. Notes: • Mailbox is the factory default setting. This setting treats each bin as a separate mailbox.
Understanding the printer menus 197 Use To Assign Type/Bin Plain Paper Bin Card Stock Bin Transparency Bin Recycled Bin Labels Bin Vinyl Labels Bin Bond Bin Envelope Bin Rough Envelope Bin Letterhead Bin Preprinted Bin Colored Bin Light Paper Bin Heavy Paper Bin Rough/Cotton Bin Custom [x] Bin Select a bin for each supported paper type. For each type, select the following options: Disabled Standard Bin Bin [x] Notes: • Disabled is the factory default setting.
Understanding the printer menus 198 Use To Profiles List Print a list of profiles stored in the printer. Note: This menu item appears only when LDSS is enabled. Print Fonts PCL Fonts PostScript Fonts Print a report of all the fonts available for the printer language currently set in the printer. Print Directory Print a list of all the resources stored in an optional flash memory card or printer hard disk. Note: A separate list is available for PCL and PostScript emulations.
Understanding the printer menus 199 Use To PS SmartSwitch On Off Set the printer to automatically switch to PS emulation when a print job requires it, regardless of the default printer language. Notes: • On is the factory default setting. • If PS SmartSwitch is disabled, then the printer does not examine incoming data and it uses the default printer language specified in the Setup menu.
Understanding the printer menus 200 Reports menu To access the menu, navigate to either of the following: • Network/Ports > Standard Network > Standard Network Setup > Reports • Network/Ports > Network [x] > Network [x] Setup > Reports Use To Print Setup Page Print a report containing information about the network printer settings, such as the TCP/IP address.
Understanding the printer menus 201 Use To IP Address View or change the current TCP/IP address. Note: Manually setting the IP address sets the Enable DHCP and Enable Auto IP settings to Off. It also sets Enable BOOTP and Enable RARP to Off on systems that support BOOTP and RARP. Netmask View or change the current TCP/IP netmask. Gateway View or change the current TCP/IP gateway. Enable DHCP On Off Specify the DHCP address and parameter assignment.
Understanding the printer menus 202 IPv6 menu To access the menu, navigate to any of the following: • Network/Ports menu > Standard Network > Standard Network Setup >IPv6 • Network/Ports menu > Network [x] > Network [x] Setup > IPv6 Note: This menu is available only in network printers or printers that are attached to print servers. Use To Enable IPv6 On Off Enable IPv6 in the printer.
Understanding the printer menus 203 Use To Network Mode Specify the network mode. BSS Type Infrastructure Ad hoc Notes: • Infrastructure is the factory default setting. This lets the printer access a network using an access point. • Ad hoc configures wireless connection directly between the printer and a computer. Compatibility 802.11b/g 802.11b/g/n Specify the wireless standard for the wireless network. Choose Network Select an available network for the printer to use.
Understanding the printer menus 204 Standard USB menu Use To PCL SmartSwitch On Off Set the printer to automatically switch to PCL emulation when a print job received through a USB port requires it, regardless of the default printer language. Notes: • On is the factory default setting. • When set to Off, the printer does not examine incoming data. The printer uses PostScript emulation if the PS SmartSwitch is set to On.
Understanding the printer menus 205 Use To Job Buffering Off On Auto Temporarily store print jobs in the printer hard disk before printing. Notes: • Off is the factory default setting. • On buffers jobs on the printer hard disk. • Auto buffers print jobs only if the printer is busy processing data from another input port. • Changing this setting from the printer control panel and then exiting the menus causes the printer to restart. The menu selection is then updated.
Understanding the printer menus 206 Use To PS SmartSwitch On Off Set the printer to automatically switch to PS emulation when a print job received through a serial port requires it, regardless of the default printer language. Notes: • On is the factory default setting. • When set to Off, the printer does not examine incoming data. The printer uses PCL emulation if PCL SmartSwitch is set to On. It uses the default printer language specified in the Setup menu if PCL SmartSwitch is set to Off.
Understanding the printer menus 207 Use To Protocol Standard Fastbytes Specify the parallel port protocol. Notes: • Fastbytes is the factory default setting. It provides compatibility with most existing parallel ports and is the recommended setting. • Standard tries to resolve parallel port communication problems. Honor Init On Off Determine if the printer honors printer hardware initialization requests from the computer. Notes: • Off is the factory default setting.
Understanding the printer menus 208 Use To PCL SmartSwitch On Off Set the printer to automatically switch to PCL emulation when a print job received through a serial port requires it, regardless of the default printer language. Notes: • On is the factory default setting. • When set to Off, the printer does not examine incoming data. The printer uses PostScript emulation if PS SmartSwitch is set to On. It uses the default printer language specified in the Setup menu if PS SmartSwitch is set to Off.
Understanding the printer menus 209 Use To Job Buffering Off On Auto Temporarily store print jobs on the printer hard disk before printing. Notes: • Off is the factory default setting. The printer does not buffer print jobs on the printer hard disk. • On buffers print jobs on the printer hard disk. • Auto buffers print jobs only if the printer is busy processing data from another input port.
Understanding the printer menus 210 Use To Parity Even Odd None Ignore Set the parity for serial input and output data frames. Honor DSR On Off Determine whether the printer uses the DSR Signal. Note: None is the factory default setting. Notes: • Off is the factory default setting. • DSR is a handshaking signal used by most serial cables. The serial port uses DSR to distinguish data sent by the computer from data created by electrical noise in the serial cable.
Understanding the printer menus 211 Use To Device‑Initiated E‑mail None Use Device SMTP Credentials Specify what credentials will be used when communicating to the SMTP server. Some SMTP servers require credentials to send an e-mail. Notes: User‑Initiated E‑mail None Use Device SMTP Credentials Use Session User ID & Password Use Session E‑mail address & Password Prompt User • None is the factory default setting for Device‑Initiated E‑mail and User‑Initiated E‑mail.
Understanding the printer menus 212 Use To Edit Access Controls Administrative Menus Function Access Management Solutions Cancel jobs at the Device Control access to printer menus, firmware updates, held jobs, and other access points. Miscellaneous Security Settings menu Note: This menu appears only in touch‑screen printer models.
Understanding the printer menus Use 213 To Confidential Job Expiration Limit the amount of time a confidential print job stays in the printer before it is deleted. Off Notes: 1 hour • If the “Confidential Job Expiration” setting is changed while confidential print jobs 4 hours reside in the printer RAM or printer hard disk, then the expiration time for those print 24 hours jobs does not change to the new default value.
Understanding the printer menus 214 Use To Automatic Method Single pass Multiple pass Mark all disk space used by a previous print job. This method does not permit the file system to reuse this space until it has been cleared. Notes: • “Single pass” is the factory default setting. • Only automatic wiping enables users to erase temporary data files without having to turn off the printer for an extended amount of time.
Understanding the printer menus 215 Use To Time Zone [list of time zones] Select the time zone. Automatically observe DST On Off Set the printer to use the applicable daylight saving time (DST) start and end times associated with the printer Time Zone setting. Enable NTP On Off Enable Network Time Protocol, which synchronizes the clocks of devices on a network. Note: GMT is the factory default setting. Note: On is the factory default setting. Notes: • On is the factory default setting.
Understanding the printer menus 216 Use To Show Supply Estimates Show estimates Do not show estimates Get an estimate on the status of supplies. Notes: • Show estimates displays the estimated supply status in pages on the control panel, printer Web page, and on the Menu Settings and the Device Statistics reports. • Do not show estimates hides the estimated supply status in any location. Eco-Mode Off Energy Energy/Paper Paper Minimize the use of energy, paper, or specialty media.
Understanding the printer menus 217 Use To Keyboard Keyboard Type English Francais Francais Canadien Deutsch Italiano Espanol Greek Dansk Norsk Nederlands Svenska Suomi Portuguese Russian Polski Swiss German Swiss French Korean Magyar Turkish Czech Simplified Chinese Traditional Chinese Japanese Custom Key 1 Custom Key 2 Specify a language and custom key information for the control panel keyboard. The additional tabs enable access to accent marks and symbols from the keypad on the control panel.
Understanding the printer menus 218 Use To Displayed Information Left side Right side Specify what is displayed on the upper left and right corners of the control panel. For the Left side and Right side options, select from the following options: None IP Address Hostname Contact Name Location Date/Time mDNS/DDNS Service Name Zero Configuration Name Custom Text [x] Model Name Notes: • This menu appears only in touch‑screen printer models. • IP Address is the factory default setting for Left side.
Understanding the printer menus 219 Use To Displayed Information (continued) Paper Jam Load Paper Service Errors Customize the displayed information for Paper Jam, Load Paper, and Service Errors. Select from the following options: Display Yes No Message to Display Default Alternate Default [text entry] Alternate [text entry] Notes: • This menu appears only in touch‑screen printer models. • No is the factory default setting for Display. • Default is the factory default setting for Message to Display.
Understanding the printer menus 220 Use To Time Format 12 hour A.M./P.M. 24 hour clock Format the printer time. Screen Brightness 20–100 Specify the brightness of the display. Note: This menu appears only in touch‑screen printer models. Notes: • This menu appears only in touch‑screen printer models. • 100 is the factory default setting. Output Lighting Normal/Standby Mode Off Dim Bright Set the amount of light from the bin.
Understanding the printer menus 221 Use To Location Specify the location of the printer. Notes: • This menu appears only in touch‑screen printer models. • The location will be stored on the Embedded Web Server. Alarms Alarm Control Cartridge Alarm Staple Alarm Hole Punch Alarm Set an alarm to sound when the printer requires user intervention. For each alarm type, select from the following options: Off Single Continuous Notes: • Single is the factory default setting for Alarm Control.
Understanding the printer menus 222 Use To Timeouts Hibernate Timeout Disabled 20 minutes 1 hour 2 hours 3 hours 6 hours 1 day 2 days 3 days 1 week 2 weeks 1 month Set the amount of time the printer waits before it enters Hibernate mode. Timeouts Screen Timeout 15–300 sec Set the amount of time in seconds the printer waits before returning the display to a ready state.
Understanding the printer menus 223 Use To Timeouts Job Hold Timeout 5–255 sec Set the amount of time the printer waits for user intervention before it holds jobs that require unavailable resources and continues to print other jobs in the print queue. Notes: • 30 sec is the factory default setting. • This menu appears only when a printer hard disk is installed.
Understanding the printer menus 224 Use To Print Recovery Page Protect Off On Let the printer successfully print a page that may not have printed otherwise. Notes: • Off is the factory default setting. Off prints a partial page when there is not enough memory to print the whole page. • On sets the printer to process the whole page so that the entire page prints.
Understanding the printer menus 225 Use To Export Configuration Package Export Export the printer configuration package to a flash drive. Note: The configuration package cannot be exported unless a flash drive is attached to the printer. Flash Drive Menu Print Settings menu Use To Copies 1–999 Specify a default number of copies for each print job. Paper Source Tray [x] Set a default paper source for all print jobs. Note: 1 is the factory default setting.
Understanding the printer menus 226 Use To Hole Punch Mode 2 holes 3 holes 4 holes Specify the number of holes to be made on the prints. Notes: • “3 holes” is the U.S. factory default setting. “4 holes” is the international factory default setting. • This menu appears only when a supported staple, hole punch finisher is installed. Duplex Binding Long Edge Short Edge Define the way duplexed pages are bound and printed.
Understanding the printer menus 227 Use To Separator Sheets Off Between Copies Between Jobs Between Pages Specify if blank separator sheets are inserted. Notes: • Off is the factory default setting. • Between Copies inserts a blank sheet between each copy of a print job if Collate is set to “(1,2,3) (1,2,3).” If Collate is set to “(1,1,1) (2,2,2),” then a blank page is inserted between each set of printed pages, such as after all page 1's and after all page 2's.
Understanding the printer menus 228 Use To Job Waiting On Off Specify that print jobs be removed from the print queue when they require unavailable printer options or custom settings. They are stored in a separate print queue, so other jobs print normally. When the missing information or options, or both are obtained, the stored jobs print. Notes: • Off is the factory default setting. • This menu appears only when a formatted, working printer hard disk is installed.
Understanding the printer menus 229 Use To Print All Order Alphabetical Oldest First Newest First Specify the order in which held and confidential jobs are printed when Print All is selected. Note: Alphabetical is the factory default setting. Finishing menu Use To Sides (Duplex) 1 sided 2 sided Specify whether two‑sided (duplex) printing is set as the default for all print jobs. Notes: • “1 sided” is the factory default setting. • You can set two‑sided printing from the printer software.
Understanding the printer menus 230 Use To Separator Sheets Off Between Copies Between Jobs Between Pages Specify whether blank separator sheets are inserted. Notes: • Off is the factory default setting. • Between Copies inserts a blank sheet between each copy of a print job if Collate is set to “(1,2,3) (1,2,3).” If Collate is set to “(1,1,1) (2,2,2),” then a blank page is inserted between each set of printed pages, such as after all page 1's and after all page 2's.
Understanding the printer menus 231 Use To Staple Job Off On Specify whether printed output is stapled. Run Stapler Test Print a report that confirms that the staple finisher is functioning properly. Notes: • Off is the factory default setting. • This menu appears only when a supported staple finisher is installed. Note: This menu appears only when a supported staple finisher is installed.
Understanding the printer menus 232 Quality menu Use To Print Resolution 300 dpi 600 dpi 1200 dpi 1200 Image Q 2400 Image Q Specify the printed output resolution in dots per inch. Pixel Boost Off Fonts Horizontally Vertically Both directions Enable more pixels to print in clusters for clarity, in order to enhance images horizontally or vertically, or to enhance fonts. Toner Darkness 1–10 Lighten or darken the printed output. Note: 600 dpi is the factory default setting.
Understanding the printer menus 233 Use To Job Accounting Utilities Print and delete log files or export them to a flash drive. Accounting Log Frequency Daily Weekly Monthly Set how often a log file is created. Log Action at End of Frequency None E‑mail Current Log E‑mail & Delete Current Log Post Current Log Post & Delete Current Log Set how the printer responds when the frequency threshold expires.
Understanding the printer menus 234 Utilities menu Use To Remove Held Jobs Confidential Held Not Restored All Delete confidential and held jobs from the printer hard disk. Notes: • Selecting a setting affects only print jobs that are stored in the printer hard disk. Bookmarks, print jobs on flash drives, and other types of held jobs are not affected. • Not Restored removes all Print and Hold jobs that are not restored from the printer hard disk or printer memory.
Understanding the printer menus 235 PDF menu Use To Scale to Fit Yes No Scale page content to fit the selected paper size. Annotations Do Not Print Print Print annotations in a PDF. Note: No is the factory default setting. Note: Do Not Print is the factory default setting. PostScript menu Use To Print PS Error On Off Print a page containing the PostScript error. Lock PS Startup Mode On Off Disable the SysStart file. Font Priority Resident Flash/Disk Establish the font search order.
Understanding the printer menus 236 Use To Font Name Courier 10 Identify a specific font and the option where it is stored. Symbol Set 10U PC‑8 12U PC‑850 Specify the symbol set for each font name. Note: Courier 10 is the factory default setting. Courier 10 shows the font name, font ID, and the storage location in the printer. The font source abbreviation is R for Resident, F for Flash, K for Disk, and D for Download. Notes: • 10U PC‑8 is the US factory default setting.
Understanding the printer menus 237 Use To PCL Emulation Settings A4 Width 198 mm 203 mm Set the printer to print on A4‑size paper. Notes: • “198 mm” is the factory default setting. • The 203‑mm setting sets the width of the page to allow printing of eighty 10‑pitch characters. PCL Emulation Settings Auto CR after LF On Off Specify whether the printer automatically performs a carriage return (CR) after a line feed (LF) control command.
Understanding the printer menus 238 Use To Tray Renumber Restore Defaults Yes No Restore all tray and feeder assignments to the factory default settings. PPDS menu Menu item Description Orientation Portrait Landscape Sets the orientation of the text and graphics on the page Lines per Page 1–255 Sets the number of lines that print on each page Notes: • Portrait is the factory default setting. • Settings are duplicated in the PCL Emulation menu. Notes: • 64 is the factory default setting.
Understanding the printer menus 239 Menu item Description Tray 1 Renumber Off Tray 2 Configures the printer to work with printer software or programs that use different source assignments for trays, drawers, and feeders Notes: • Off is the factory default setting. • Tray 2 is displayed only when it is installed. Auto CR after LF On Off Specifies whether the printer automatically performs a carriage return (CR) after a line feed (LF) control command Notes: • Off is the factory default setting.
Understanding the printer menus 240 HTML menu Use Font Name Albertus MT Antique Olive Apple Chancery Arial MT Avant Garde Bodoni Bookman Chicago Clarendon Cooper Black Copperplate Coronet Courier Eurostile Garamond Geneva Gill Sans Goudy Helvetica Hoefler Text Intl CG Times Intl Courier Intl Univers To Joanna MT Letter Gothic Lubalin Graph Marigold MonaLisa Recut Monaco New CenturySbk New York Optima Oxford Palatino StempelGaramond Taffy Times TimesNewRoman Univers Zapf Chancery NewSansMTJA NewSansMTCS N
Understanding the printer menus 241 Use To Margin Size 8–255 mm Set the page margin for HTML documents. Notes: • 19 mm is the factory default setting. • Margin size can be increased in 1‑mm increments. Backgrounds Do Not Print Print Specify whether to print backgrounds on HTML documents. Note: Print is the factory default setting. Image menu Use To Auto Fit On Off Select the optimal paper size, scaling, and orientation. Invert On Off Invert bitonal monochrome images.
Understanding the printer menus 242 Menu item Description Menu Map Provides a list of the control panel menus and settings Information Guide Provides help in locating additional information Connection Guide Provides information about connecting the printer locally (USB) or to a network Moving Guide Provides instructions for safely moving the printer Supplies Guide Provides information about ordering supplies
Saving money and the environment 243 Saving money and the environment Lexmark is committed to environmental sustainability and is continually improving its printers to reduce their impact on the environment. We design with the environment in mind, engineer our packaging to reduce materials, and provide collection and recycling programs. For more information, see: • The Notices chapter • The Environmental Sustainability section of the Lexmark Web site at www.lexmark.
Saving money and the environment 244 Conserving supplies Use both sides of the paper If your printer model supports two‑sided printing, then you can control whether print appears on one or two sides of the paper. Notes: • Two-sided printing is the default setting in the print driver. • For a complete list of supported products and countries, go to http://support.lexmark.com.
Saving money and the environment 245 Recycling Lexmark packaging Lexmark continually strives to minimize packaging. Less packaging helps to ensure that Lexmark printers are transported in the most efficient and environmentally sensitive manner and that there is less packaging to dispose of. These efficiencies result in fewer greenhouse emissions, energy savings, and natural resource savings. Lexmark cartons are 100% recyclable where corrugated recycling facilities exist.
Maintaining the printer 246 Maintaining the printer Warning—Potential Damage: Failure to maintain optimum printer performance, or to replace parts and supplies, may cause damage to your printer. Ordering supplies To order parts and supplies in the U.S., contact Lexmark at 1-800-539-6275 for information about Lexmark authorized supplies dealers in your area. In other countries or regions, go to www.lexmark.com or contact the place where you purchased the printer.
Maintaining the printer 247 Item Return Program cartridge For the European Union, European Economic Area , and Switzerland Toner Cartridge 522 High Yield Toner Cartridge 522H Extra High Yield Toner Cartridge 522X* For the Asia Pacific Region (includes Australia and New Zealand) Toner Cartridge 523 High Yield Toner Cartridge 523H Extra High Yield Toner Cartridge 523X* For Latin America (includes Puerto Rico and Mexico) Toner Cartridge 524 High Yield Toner Cartridge 524H Extra High Yield T
Maintaining the printer 248 Ordering staple cartridges Item Part number Staple cartridges 25A0013 Ordering a roller kit For more information on replacing the roller kit, see the instruction sheet that came with the part. Lexmark roller kit and part number Type Part number Printer engine roller maintenance kit 40X7706 Ordering a maintenance kit To identify the supported fuser type, view the label on the fuser. Do either of the following: • Remove the toner cartridge and the imaging unit.
Maintaining the printer 249 Fuser maintenance kit type Part number Type 07 40X8427 Type 08 40X8428 Type 09 40X8429 Storing supplies Choose a cool, clean storage area for the printer supplies. Store supplies right side up in their original packing until you are ready to use them.
Maintaining the printer 250 2 Pull the cartridge out of the printer using the handle. 3 Unpack the new toner cartridge, then remove the packing material, and then shake the cartridge to redistribute the toner. 4 Insert the toner cartridge into the printer by aligning the side rails of the cartridge with the arrows on the side rails inside the printer. Note: Make sure the cartridge is fully pushed in.
Maintaining the printer 251 5 Close the multipurpose feeder door and the front cover. 2 1 Replacing the imaging unit 1 Lift the front cover, and then pull down the multipurpose feeder door.
Maintaining the printer 252 2 Pull out the toner cartridge from the printer using the handle. 3 Lift the green handle, and then pull out the imaging unit from the printer. 1 2 4 Unpack the new imaging unit, and then shake it. 5 Remove all packing material from the imaging unit. Warning—Potential Damage: Do not expose the imaging unit to direct light for more than 10 minutes. Extended exposure to light may cause print quality problems. Warning—Potential Damage: Do not touch the photoconductor drum.
Maintaining the printer 253 6 Insert the imaging unit into the printer by aligning the arrows on the side rails of the imaging unit with the arrows on the side rails inside the printer. 7 Insert the toner cartridge into the printer by aligning the side rails of the cartridge with the arrows on the side rails inside the printer.
Maintaining the printer 254 8 Close the multipurpose feeder door and the front cover. 2 1 Replacing a staple cartridge 1 Open the stapler door. 2 Pull down the latch of the staple cartridge holder, and then pull the holder out of the finisher.
Maintaining the printer 255 3 Squeeze both sides of the empty staple case with your fingers, and then remove the staple case from the cartridge. 2 1 1 4 Insert the front side of the new staple case into the staple cartridge, and then push the rear side into the cartridge. 2 1 5 Push the staple cartridge into the finisher until it clicks into place. 6 Close the stapler door. Cleaning printer parts Cleaning the printer Note: You may need to perform this task after every few months.
Maintaining the printer 256 4 Dampen a clean, lint-free cloth with water, and use it to wipe the outside of the printer. Warning—Potential Damage: Do not use household cleaners or detergents to prevent damage to the exterior of the printer. 5 Make sure all areas of the printer are dry before sending a new print job. Emptying the hole punch box 1 Pull out the hole punch box. 2 Empty the container.
Maintaining the printer 257 3 Insert the emptied hole punch box back into the finisher until it clicks into place. Moving the printer CAUTION—POTENTIAL INJURY: The printer weight is greater than 18 kg (40 lb) and requires two or more trained personnel to lift it safely. Before moving the printer CAUTION—POTENTIAL INJURY: Before moving the printer, follow these guidelines to avoid personal injury or printer damage: • Turn off the printer, and then unplug the power cord from the electrical outlet.
Maintaining the printer 258 • If the printer does not have a caster base but is configured with optional trays, then remove the trays. Note: Slide the latch on the right side of the optional tray toward the front of the tray until it clicks into place. • • • • Use the handholds located on both sides of the printer to lift it. Make sure your fingers are not under the printer when you set it down. Make sure there is adequate clearance around the printer.
Maintaining the printer 259 Warning—Potential Damage: Damage to the printer caused by improper moving is not covered by the printer warranty. Moving the printer to another location The printer and its hardware options can be safely moved to another location by following these precautions: • Any cart used to move the printer must have a surface able to support the full footprint of the printer.
Clearing jams 260 Clearing jams Carefully select paper and specialty media and load them properly to avoid paper jams. If jams occur, then follow the steps outlined in this chapter. Note: Jam Recovery is set to Auto by default. The printer reprints jammed pages unless the memory required to hold the pages is needed for other printer tasks. Avoiding jams Load paper properly • Make sure paper lies flat in the tray.
Clearing jams 261 • Do not slide the paper into the tray. Load paper as shown in the illustration. • Make sure the guides in the tray or the multipurpose feeder are properly positioned and are not pressing tightly against the paper or envelopes. • Push the tray firmly into the printer after loading paper. • If you are loading prepunched paper for use with the staple finisher, then make sure the holes on the long edge of the paper are on the right side of the tray.
Clearing jams 262 • If paper needs to be returned to the mailbox bin, then insert the paper under the bin arm, and then push the paper all the way back. 2 1 Note: If the paper is not under the bin arm, then a jam occurs due to an overfilled bin. Use recommended paper • Use only recommended paper or specialty media. • Do not load wrinkled, creased, damp, bent, or curled paper. • Flex, fan, and straighten paper or specialty media before loading it.
Clearing jams 263 1 2 3 4 5 6 11 7 10 9 8 Jam location Printer message What to do 1 Staple finisher [x]‑page jam, remove paper, open Remove paper from the stapler bin, open the stapler stapler door. Leave paper in bin. [455– door, then remove the staple cartridge, and then 457] remove the jammed staples. 2 Standard bin [x]‑page jam, remove standard bin jam. [203] 3 Inside the printer [x]‑page jam, lift front cover to remove Open the front cover and the multipurpose feeder, cartridge.
Clearing jams Jam location 264 Printer message What to do 9 Upper door and rear [x]‑page jam, open upper and lower duplex area rear door. [231–234] Open the rear door of the printer and the rear duplex area, and then remove the jammed paper. 10 Mailbox [x]‑page jam, remove paper, open mailbox rear door. Leave paper in bin. [43y.xx] Open the rear door of the mailbox, and then remove the jammed paper. 11 Staple finisher rear door [x]‑page jam, remove paper, open finisher rear door.
Clearing jams 265 3 Place the cartridge aside. 4 Lift the green handle, and then pull the imaging unit out of the printer. 1 2 5 Place the imaging unit aside on a flat, smooth surface. Warning—Potential Damage: Do not expose the imaging unit to direct light for more than 10 minutes. Extended exposure to light may cause print quality problems. 6 Pull the jammed paper gently to the right, and then remove it from the printer. Note: Make sure all paper fragments are removed.
Clearing jams 266 8 Insert the cartridge into the printer, and then push the green handle back into place. Notes: • Align the arrows on the guides of the toner cartridge with the arrows in the printer. • Make sure the cartridge is fully pushed in. 9 Close the multipurpose feeder door and the front cover. 2 1 10 Do either of the following to clear the message and continue printing: • For touch‑screen printer models, touch or Done.
Clearing jams 267 1 Pull down the rear door. 2 Firmly grasp the jammed paper on each side, and then gently pull it out. Note: Make sure all paper fragments are removed. 3 Close the rear door. 4 Do either of the following to clear the message and continue printing: • For touch‑screen printer models, touch or Done. • For non‑touch‑screen printer models, select Next > > Clear the jam, press OK > . [x]‑page jam, open upper and lower rear door.
Clearing jams 1 Pull down the rear door. 2 Firmly grasp the jammed paper on each side, and then gently pull it out. Note: Make sure all paper fragments are removed. 3 Close the rear door.
Clearing jams 269 4 Push the back of the standard tray. 5 Press down the rear duplex flap, then firmly grasp the jammed paper, and then gently pull the paper out. Note: Make sure all paper fragments are removed. 2 1 6 Insert the standard tray.
Clearing jams 270 7 Do either of the following to clear the message and continue printing: • For touch‑screen printer models, touch or Done. • For non‑touch‑screen printer models, select Next > > Clear the jam, press OK > . [x]‑page jam, remove standard bin jam. [203] 1 Firmly grasp the jammed paper on each side, and then gently pull it out. Note: Make sure all paper fragments are removed.
Clearing jams 271 2 1 3 Insert the tray. 4 Do either of the following to clear the message and continue printing: • For touch‑screen printer models, touch or Done. • For non‑touch‑screen printer models, select Next > > Clear the jam, press OK > [x]‑page jam, open tray [x]. [24x] 1 Check which tray is indicated on the printer display, and then pull the tray. 2 Firmly grasp the jammed paper on each side, and then gently pull it out. Note: Make sure all paper fragments are removed. .
Clearing jams 272 3 Insert the tray. 4 Do either of the following to clear the message and continue printing: • For touch‑screen printer models, touch or Done. • For non‑touch‑screen printer models, select Next > > Clear the jam, press OK > . [x]‑page jam, clear manual feeder. [250] 1 From the multipurpose feeder, firmly grasp the jammed paper on each side, and then gently pull it out. Note: Make sure all paper fragments are removed.
Clearing jams 273 2 Flex the sheets of paper back and forth to loosen them. Do not fold or crease the paper. Straighten the edges on a level surface. 3 Reload paper into the multipurpose feeder. 4 Slide the paper guide until it lightly rests against the edge of the paper. 5 Do either of the following to clear the message and continue printing: • For touch‑screen printer models, touch or Done. • For non‑touch‑screen printer models, select Next > > Clear the jam, press OK > .
Clearing jams 2 Open the stapler door. 3 Pull down the latch of the staple cartridge holder, and then pull the holder out of the printer. 4 Use the metal tab to lift the staple guard, and then remove any loose staples.
Clearing jams 275 5 Press down the staple guard until it clicks into place. 6 Press the staples against the metal bracket. Note: If the staples are at the rear of the cartridge, then shake the cartridge downward to bring the staples near the metal bracket.
Clearing jams 276 7 Push the cartridge holder firmly back into the stapler unit until the cartridge holder clicks into place. 8 Close the stapler door. 9 Do either of the following to clear the message and continue printing: • For touch‑screen printer models, touch or Done. • For non‑touch‑screen printer models, select Next > > Clear the jam, press OK > .
Clearing jams [x]‑page jam, remove paper, open finisher rear door. Leave paper in bin. [451] 1 Open the rear staple finisher door. 2 Firmly grasp the jammed paper on each side, and then gently pull it out. Note: Make sure all paper fragments are removed. 3 Close the staple finisher door.
Clearing jams 278 4 Do either of the following to clear the message and continue printing: • For touch‑screen printer models, touch or Done. • For non‑touch‑screen printer models, select Next > > Clear the jam, press OK > . [x]‑page jam, remove paper, open expander rear door. Leave paper in bin. [41y.xx] 1 Open the rear output expander door. 2 Firmly grasp the jammed paper on each side, and then gently pull it out. Note: Make sure all paper fragments are removed.
Clearing jams 279 3 Close the rear output expander door. 4 Do either of the following to clear the message and continue printing: • For touch‑screen printer models, touch or Done. • For non‑touch‑screen printer models, select Next > > Clear the jam, press OK > .
Clearing jams [x]‑page jam, remove paper, open mailbox rear door. Leave paper in bin. [43y.xx] 1 Open the rear mailbox door. 2 Firmly grasp the jammed paper on each side, and then gently pull it out. Note: Make sure all paper fragments are removed. 3 Close the rear mailbox door.
Clearing jams 281 4 If the jam is in the mailbox bin, then firmly grasp the jammed paper, and then gently pull it out. Note: Make sure all paper fragments are removed. 5 Do either of the following to clear the message and continue printing: • For touch‑screen printer models, touch or Done. • For non‑touch‑screen printer models, select Next > > Clear the jam, press OK > .
Troubleshooting 282 Troubleshooting Understanding the printer messages Cartridge low [88.xy] You may need to order a toner cartridge. If necessary, select Continue on the printer control panel to clear the message and continue printing. For non‑touch‑screen printer models, press to confirm. Cartridge nearly low [88.xy] If necessary, select Continue on the printer control panel to clear the message and continue printing. For non‑touch‑screen printer models, press to confirm.
Troubleshooting 283 Change [paper source] to [paper size] load [orientation] Try one or more of the following: • Load the correct paper size and type in the tray, verify the paper size and type settings are specified in the Paper menu on the printer control panel, and then select Finished changing paper. For non‑touch‑screen printer models, press to confirm. • Cancel the print job.
Troubleshooting 284 Close rear door Close the rear door of the printer. Complex page, some data may not have printed [39] Try one or more of the following: • From the printer control panel, select Continue to ignore the message and continue printing. For non‑touch‑screen printer models, press to confirm. • Cancel the current print job. For non‑touch‑screen printer models, press • Install additional printer memory. to confirm.
Troubleshooting 285 • Install a hard disk with higher capacity. Empty the hole punch box Try one or more of the following: • Empty the hole punch box. • Select Continue on the printer control panel to clear the message and continue printing. • Cancel the print job. Error reading USB drive. Remove USB. An unsupported USB device is inserted. Remove the USB device, and then insert a supported one. Error reading USB hub. Remove hub. An unsupported USB hub has been inserted.
Troubleshooting 286 Incompatible tray [x] [59] Try one or more of the following: • Remove the specified tray. • From the printer control panel, select Continue to clear the message and continue printing without using the specified tray. For non-touch-screen printer models, press to confirm. Incorrect paper size, open [paper source] [34] Note: The paper source can be a tray or a feeder. Try one or more of the following: • Load the correct size of paper in the paper source.
Troubleshooting 287 Install bin [x] Try one or more of the following: • Install the specified bin: 1 Turn off the printer. 2 Unplug the power cord from the electrical outlet. 3 Install the specified bin. 4 Connect the power cord to a properly grounded electrical outlet. 5 Turn the printer back on. • Cancel the print job. • Reset active bin Install Tray [x] Try one or more of the following: • Install the specified tray: 1 Turn off the printer. 2 Unplug the power cord from the electrical outlet.
Troubleshooting 288 Insufficient memory, some held jobs will not be restored [37] Try one or more of the following: • From the printer control panel, select Continue to clear the message. For non-touch-screen printer models, press to confirm. • Delete other held jobs to free up additional printer memory.
Troubleshooting 289 Load [paper source] with [custom type name] [paper orientation] Try one or more of the following: • Load the tray or feeder with the correct size and type of paper. • To use the tray that has the correct size or type of paper, select Finished loading paper on the printer control panel. For non‑touch‑screen printer models, press to confirm. Note: If the printer finds a tray that has the correct size and type of paper, then it feeds from that tray.
Troubleshooting 290 Load manual feeder with [custom type name] [paper orientation] Try one or more of the following: • Load the multipurpose feeder with the correct size and type of paper. • Depending on your printer model, touch Continue or press to clear the message and continue printing. Note: If no paper is loaded in the feeder when Continue or is selected, then the printer manually overrides the request, and then prints from an automatically selected tray. • Cancel the current job.
Troubleshooting 291 If necessary, select Continue to clear the message and continue printing. For non‑touch‑screen printer models, press to confirm. Maintenance kit very low, [x] estimated pages remain [80.xy] You may need to replace the maintenance kit very soon. For more information, visit the Lexmark support Web site at http://support.lexmark.com or contact customer support, and then report the message.
Troubleshooting 292 PPDS font error [50] Try one or more of the following: • From the printer control panel, select Continue to clear the message and continue printing. For non‑touch‑screen printer models, press to confirm. • If the printer cannot find the requested font, then from the printer control panel, navigate to: PPDS menu > Best Fit > On The printer will find a similar font and reformat the affected text. • Cancel the current print job.
Troubleshooting 293 3 Remove the specified bin. 4 Contact customer support. • Select Continue on the printer control panel to clear the message and print without using the specified bin. For non-touch-screen printer models, press to confirm. Reattach bins [x] – [y] Try one or more of the following: • Turn off the printer, and then turn it back on. • Reattach the specified bins: 1 Turn off the printer. 2 Unplug the power cord from the electrical outlet. 3 Remove the specified bins. 4 Reattach the bins.
Troubleshooting 294 Reinstall missing or unresponsive imaging unit [31.xy] Try one or more of the following: • Check if the imaging unit is missing. If missing, install the imaging unit. For information on installing the imaging unit, see the “Replacing supplies” section of the User’s Guide. • If the imaging unit is installed, then remove the unresponsive imaging unit, and then reinstall it. Note: If the message appears after reinstalling the supply, then the imaging unit is defective.
Troubleshooting 295 If removing the paper does not clear the message, then select Continue on the printer control panel. For non-touchscreen printer models, press to confirm. Replace cartridge, 0 estimated pages remain [88.xy] Replace the toner cartridge to clear the message and continue printing. For more information, see the instruction sheet that came with the supply or see the “Replacing supplies” section of the User’s Guide.
Troubleshooting 296 Replace roller kit [81.xx] 1 Replace the roller kit. For more information, see the instruction sheet that came with the part. 2 Press to clear the message and continue printing. Replace unsupported cartridge [32.xy] Remove the toner cartridge, and then install a supported one to clear the message and continue printing. For more information, see the instruction sheet that came with the supply or see the “Replacing supplies” section of the User’s Guide.
Troubleshooting 297 Some held jobs were not restored Select Continue to clear the message. For non‑touch‑screen printer models, press to confirm. Note: Held jobs that are not restored remain in the printer hard disk and are inaccessible. Standard network software error [54] Try one or more of the following: • From the printer control panel, select Continue to continue printing. For non‑touch‑screen printer models, press to confirm. • Turn off the printer and then turn it back on.
Troubleshooting 298 4 Connect the power cord to a properly grounded electrical outlet. 5 Turn the printer back on. Too many flash options installed [58] 1 Turn off the printer. 2 Unplug the power cord from the electrical outlet. 3 Remove the extra flash memory. 4 Connect the power cord to a properly grounded electrical outlet. 5 Turn the printer back on. Too many trays attached [58] 1 Turn off the printer. 2 Unplug the power cord from the electrical outlet. 3 Remove the extra trays.
Troubleshooting 299 Unsupported option in slot [x] [55] 1 Turn off the printer. 2 Unplug the power cord from the wall outlet. 3 Remove the unsupported option card from the printer controller board, and then replace it with a supported card. 4 Connect the power cord to a properly grounded electrical outlet. 5 Turn the printer back on. USB port [x] disabled [56] Try one or more of the following: • Select Continue to clear the message. For non-touch-screen printer models, press to confirm.
Troubleshooting 300 Action Yes No Step 3 Go to step 4. Plug one end of the power cord into the printer and the other to a properly grounded electrical outlet. Unplug the other electrical equipment, and then turn on the printer. If the printer does not work, then reconnect the other electrical equipment. Go to step 5. Go to step 6. Make sure to match the following: Check if one end of the power cord is plugged into the printer and the other to a properly grounded electrical outlet.
Troubleshooting 301 Action Yes No Step 10 Go to step 11. Use correct printer driver settings. Go to step 12. Install the correct printer driver. Check if you have selected the correct port settings in the printer driver. Are the port settings correct? Step 11 Check the installed printer driver. Is the correct printer driver installed? Step 12 Turn off the printer, then wait for about 10 seconds, and then turn the printer back on. The problem is solved. Contact customer support.
Troubleshooting 302 Action Yes No Step 2 The problem is solved. Go to step 3. Do one or more of the following: • Delete the print job, and then resend it. • If you are printing PDF files, then generate a new file, and then print it again. Did the jobs print? Step 3 a Increase the printer memory. Do one or more of the following: The problem is solved. Contact customer support. • Delete some print jobs. • Install additional printer memory. b Resend the print job.
Troubleshooting 303 Action Yes No Step 3 a Check for an error message on the display. Go to step 4. The problem is solved. Go to step 5. The problem is solved. Contact customer support. The problem is solved. Action Yes No Step 1 Deactivate Hex Trace mode. Go to step 2. Contact customer support. The problem is solved. Action Yes No Step 1 a Check if you are printing on paper that is supported by the tray. The problem is solved. Go to step 2. b Clear the message.
Troubleshooting Action 304 Yes No The problem is solved. Go to step 3. Step 2 a From the Paper menu on the printer control panel, set the paper size and type to match the paper loaded in the tray. b Resend the print job. Did the job print from the correct tray or on the correct paper? Step 3 a Depending on your operating system, open Printing Preferences or the Print dialog, and then specify the paper type. b Resend the print job. The problem is solved. Go to step 4.
Troubleshooting 305 Multiple‑language PDF files do not print Action Yes No Step 1 The problem is solved. Go to step 2. a Check if the print options for the PDF output are set to embed all fonts. b Generate a new PDF file, and then resend the print job. Do the files print? Step 2 a Open the document you want to print in Adobe Acrobat. The problem is solved. Contact customer support. b Click File > Print > Advanced > Print As Image > OK > OK .
Troubleshooting 306 Action Yes Step 5 The problem is solved. Contact customer support. Install additional printer memory, and then resend the print job. No Did the job print? Print jobs do not print Action Yes No Step 1 The problem is solved. Go to step 2. a From the document you are trying to print, open the Print dialog and check if you have selected the correct printer. Note: If the printer is not the default printer, then you must select the printer for each document that you want to print.
Troubleshooting 307 Action Yes No Step 6 a Remove, and then reinstall the printer software. For more information, see “Installing the printer” on page 34. The problem is solved. Contact customer support. Note: The printer software is available at http://support.lexmark.com. b Resend the print job. Do the jobs print? Printing slows down Notes: • When printing using narrow paper, the printer prints at a reduced speed to prevent damage to the fuser.
Troubleshooting Action 308 Yes No Step 1 The problem is solved. Go to step 2. a Open the trays, and then check if they contain paper of the same size and type. • Check if the paper guides are in the correct positions for the size of the paper loaded in each tray. • Check if the paper size indicators on the paper guides are aligned with the paper size indicators on the tray. b Resend the print job. Do the trays link correctly? The problem is solved. Contact customer Step 2 support.
Troubleshooting 309 Hardware and internal option problems 2100-sheet tray problems Action Yes No Step 1 a Pull out the tray, and then do one or more of the following: The problem is solved. Go to step 2. • Make sure paper lies flat in the tray. • Check for paper jams or misfeeds. • Check if the paper size indicators on the paper guides are aligned with the paper size indicators on the tray. • Check if the paper guides are aligned against the edges of the paper.
Troubleshooting 310 Cannot detect internal option Action Yes No Step 1 The problem is solved. Go to step 2. Turn off the printer, then wait for about 10 seconds, and then turn on the printer. Does the internal option operate correctly? Step 2 Go to step 3. Connect the internal option to the controller board. Go to step 4. Reinstall the internal option. Check if the internal option is properly installed in the controller board.
Troubleshooting 311 Action Yes Step 2 The problem is solved. Contact customer support. Check the cable and the internal print server connection. Use the correct cable, and then check if it is securely connected to the internal print server. No Does the internal print server operate correctly? Internal Solutions Port does not operate correctly Action Yes No Step 1 Go to step 2. Check if you have a supported ISP. Make sure the Internal Solutions Port (ISP) is installed. a Install the ISP.
Troubleshooting 312 Action Yes No Step 2 a Turn off the printer, then wait about 10 seconds, and then turn the printer back on. b Resend the print job. The problem is solved. Go to step 3. Is the tray working? Step 3 Go to step 4. Check if the tray is installed and recognized by the printer. Print a menu settings page, and then check if the tray is listed in the Installed Features list. Reinstall the tray. For more information, see the setup documentation that came with the tray.
Troubleshooting 313 Paper feed problems Jammed pages are not reprinted Action Yes No The problem is solved. Contact customer support. a Turn on jam recovery. 1 From the printer control panel, navigate to: Settings > General Settings > Print Recovery > Jam Recovery 2 Select On or Auto. 3 Depending on your printer model, press or touch Submit. b Resend the pages that did not print.
Troubleshooting 314 Paper jam message remains after jam is cleared Action a Do either of the following: • For touch‑screen printer models, touch No Contact customer support. The problem is solved. Yes No or Done. • For non‑touch‑screen printer models, select Next > the jam, press OK > Yes > Clear . b Follow the instructions on the printer display. Does the paper jam message remain? Print quality problems Characters have jagged or uneven edges Action Go to step 2.
Troubleshooting 315 Clipped pages or images Leading edge ABCDE ABCDE ABCDE Trailing edge Action Yes Go to step 2. Step 1 a Move the width and length guides in the tray to the correct positions for the paper loaded. b Resend the print job. No The problem is solved. Is the page or image clipped? Step 2 Go to step 3. From the printer control panel, set the paper size and type in the Paper menu to match the paper loaded in the tray.
Troubleshooting 316 Compressed images appear on prints Note: Printing on letter-size paper using a 220-volt fuser compresses images. Action Yes No The problem is solved. Go to step 2. Step 1 a Make sure the size of the paper loaded in the tray matches the fuser type. Note: Use a 110-volt fuser for printing on letter-size paper and a 220-volt fuser for printing on A4‑size paper. b Resend the print job. Do compressed images still appear? Step 2 a Replace the fuser.
Troubleshooting 317 Action Yes No Step 2 The problem is solved. Go to step 3. Reinstall the imaging unit and the toner cartridge. a Remove the toner cartridge. b Remove the imaging unit. Warning—Potential Damage: Do not expose the imaging unit to direct light for more than 10 minutes. Extended exposure to light can cause print quality problems. c Install the imaging unit, and then the cartridge. d Resend the print job.
Troubleshooting 318 Action Yes No Step 3 a Redistribute the toner in the imaging unit. 1 Remove the toner cartridge, and then the imaging unit. Go to step 4. The problem is solved. Contact customer support. The problem is solved. Yes No 2 Firmly shake the imaging unit. Warning—Potential Damage: Do not expose the imaging unit to direct light for more than 10 minutes. Extended exposure to light may cause print quality problems. 3 Reinstall the imaging unit, and then the cartridge.
Troubleshooting 319 Action Yes No Step 3 a Depending on your operating system, specify the paper size from Printing Preferences or from the Print dialog. b Resend the print job. The problem is solved. Contact customer support. Are the margins correct? Paper curl Action Yes No Step 1 Go to step 2. Adjust the width and length guides. Go to step 3. Specify the paper type and weight from the tray settings to match the paper loaded in the tray. Go to step 4. The problem is solved. Go to step 5.
Troubleshooting 320 Print irregularities Leading edge ) ) ABCDE ABCDE ABCDE Trailing edge Action Yes Step 1 Go to step 2. a Move the width and length guides in the tray to the correct positions for the size of the paper loaded in the tray. b Resend the print job. No The problem is solved. Do print irregularities still appear? Step 2 Go to step 3. Specify the paper size and type from the tray settings to match the paper loaded in the tray. Go to step 4. The problem is solved.
Troubleshooting 321 Print is too dark ABC DEF Action Yes Go to step 2. Step 1 a From the Quality menu on the printer control panel, reduce the toner darkness. No The problem is solved. Note: 8 is the factory default setting. b Resend the print job. Is the print still too dark? Step 2 Go to step 3. a From the printer control panel, set the paper type, texture and weight in the Paper menu to match the paper loaded in the tray. b Resend the print job.
Troubleshooting 322 Action Yes No Step 5 a Load paper from a fresh package. Go to step 6. The problem is solved. Contact customer support. The problem is solved. Yes No Note: Paper absorbs moisture due to high humidity. Store paper in its original wrapper until you use it. b Resend the print job. Is the print still too dark? Step 6 Replace the imaging unit, and then resend the print job. Is the print still too dark? Print is too light ABC DEF Action Go to step 2.
Troubleshooting 323 Action Yes Step 4 From the printer Go to step 5. control panel, change the texture settings in the Paper Texture menu to match the paper you are printing on. Make sure that the paper has no texture or rough finishes. Are you printing on textured or rough paper? Step 5 a Load paper from a fresh package. No Go to step 6. The problem is solved. Go to step 7. The problem is solved. Contact customer support. The problem is solved.
Troubleshooting 324 Action Yes No Step 1 a Check if there is packing material left on the imaging unit. 1 Remove the toner cartridge, and then the imaging unit. Go to step 2. The problem is solved. Go to step 3. The problem is solved. Contact customer support. The problem is solved. 2 Check if the packing material is properly removed from the imaging unit. Warning—Potential Damage: Do not expose the imaging unit to direct light for more than 10 minutes.
Troubleshooting 325 Action Yes No Step 1 a Reinstall the imaging unit. 1 Remove the toner cartridge, and then the imaging unit. Go to step 2. The problem is solved. Contact customer support. The problem is solved. Yes No Warning—Potential Damage: Do not expose the imaging unit to direct light for more than 10 minutes. Extended exposure to light may cause print quality problems. 2 Install the imaging unit, and then the cartridge. b Resend the print job.
Troubleshooting 326 Shadow images appear on prints Leading edge A AB BC CD D A B C D ABCD Trailing edge Action Yes No Step 1 Go to step 2. Load paper with the correct paper type and weight in the tray. Go to step 3. Change the paper loaded in the tray to match the paper type and weight specified in the tray settings. Go to step 4. The problem is solved. Contact customer support. The problem is solved. Load paper with the correct paper type and weight in the tray.
Troubleshooting Action 327 Yes Step 1 Go to step 2. a Move the width and length guides in the tray to the correct positions for the size of the paper loaded. b Resend the print job. No The problem is solved. Is the print still skewed? Step 2 a Check if you are printing on a paper that is supported by the tray. Contact customer support. The problem is solved. Yes No b Resend the print job.
Troubleshooting 328 Action Yes No Step 4 a Reinstall the imaging unit. 1 Remove the toner cartridge, and then the imaging unit. Go to step 5. The problem is solved. Contact customer support. The problem is solved. Yes No Warning—Potential Damage: Do not expose the imaging unit to direct light for more than 10 minutes. Extended exposure to light may cause print quality problems. 2 Install the imaging unit, and then the cartridge. b Resend the print job.
Troubleshooting 329 Action Yes No Step 3 a Load paper from a fresh package. Go to step 4. The problem is solved. Go to step 5. The problem is solved. Note: Paper absorbs moisture due to high humidity. Store paper in its original wrapper until you use it. b Resend the print job. Do streaked vertical lines appear on prints? Step 4 a Reinstall the imaging unit. 1 Remove the toner cartridge, and then the imaging unit.
Troubleshooting 330 Action Yes Step 2 The problem is solved. Contact customer support. Replace the imaging unit, and then resend the print job. No Did the toner fog or background shading disappear from the prints? Toner rubs off Leading edge ABC DEF Trailing edge Action Yes No Step 1 Go to step 2. Specify the paper type, texture, and weight from the tray settings to match the paper loaded in the tray. Contact customer support. The problem is solved.
Troubleshooting 331 Transparency print quality is poor Action Yes No Step 1 Go to step 2. Set the paper type to Transparency. Contact customer support. The problem is solved. Action Yes No Replace the imaging unit, and then resend the print job. Contact customer support. The problem is solved. Action Yes No Step 1 a Make sure your software program is using a correct fill pattern. Go to step 2. The problem is solved.
Troubleshooting Action 332 Yes Go to step 3. Step 2 a From the printer control panel, set the paper type and weight in the Paper menu to match the paper loaded in the tray. b Resend the print job. No The problem is solved. Do vertical voids appear on prints? Step 3 Go to step 4. The problem is solved. Go to step 5. The problem is solved. Contact customer support. The problem is solved. Check if you are using a recommended type of paper.
Troubleshooting 333 Solving home screen application problems This troubleshooting step applies only to touch-screen printer models. An application error has occurred Action Yes No Step 1 Go to step 2. Contact customer support. Check the system log for relevant details. a Open a Web browser, and then type the printer IP address in the address field. If you do not know the IP address of the printer, then you can: • View the IP address on the printer home screen.
Troubleshooting 334 Action Yes No Step 3 Go to step 4. Contact your system support person. Go to step 5. Tighten the cable connection. Go to step 6. Contact your system support person. Check if the network connection is working. Is the network connection working? Step 4 Make sure the cable connections to the printer and print server are secure. For more information, see the setup documentation that came with the printer.
Notices 335 Notices Product information Product name: Lexmark MS810n, MS810dn, MS811n, MS811dn, MS812dn, MS810de, MS812de Machine type: 4063 Model(s): 210, 230, 23E, 410, 430, 630, 63E Edition notice October 2014 The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC.
Notices 336 Trademarks Lexmark, Lexmark with diamond design, MarkNet, and MarkVision are trademarks of Lexmark International, Inc., registered in the United States and/or other countries. Mac and the Mac logo are trademarks of Apple Inc., registered in the U.S. and other countries. PCL® is a registered trademark of the Hewlett-Packard Company. PCL is Hewlett-Packard Company’s designation of a set of printer commands (language) and functions included in its printer products.
Notices 337 All other trademarks are the property of their respective owners. AirPrint and the AirPrint logo are trademarks of Apple, Inc. Licensing notices All licensing notices associated with this product can be viewed from the root directory of the installation software CD. Noise emission levels The following measurements were made in accordance with ISO 7779 and reported in conformance with ISO 9296. Note: Some modes may not apply to your product.
Notices 338 Static sensitivity notice This symbol identifies static-sensitive parts. Do not touch in the areas near these symbols without first touching the metal frame of the printer. ENERGY STAR Any Lexmark product bearing the ENERGY STAR emblem on the product or on a start-up screen is certified to comply with Environmental Protection Agency (EPA) ENERGY STAR requirements as configured when shipped by Lexmark. Temperature information Ambient operating temperature 15.6 to 32.
Notices 339 DANGER - Invisible laser radiation when cartridges are removed and interlock defeated. Avoid exposure to laser beam. PERIGO - Radiação a laser invisível será liberada se os cartuchos forem removidos e o lacre rompido. Evite a exposição aos feixes de laser. Opasnost - Nevidljivo lasersko zračenje kada su kasete uklonjene i poništena sigurnosna veza. Izbjegavati izlaganje zracima. NEBEZPEČÍ - Když jsou vyjmuty kazety a je odblokována pojistka, ze zařízení je vysíláno neviditelné laserové záření.
Notices 340 Values are subject to change. See www.lexmark.com for current values. Sleep Mode This product is designed with an energy-saving mode called Sleep Mode. The Sleep Mode saves energy by lowering power consumption during extended periods of inactivity. The Sleep Mode is automatically engaged after this product is not used for a specified period of time, called the Sleep Mode Timeout.
Notices 341 Patent acknowledgment The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for Elliptic Curve Cryptography (ECC) Cipher Suites for Transport Layer Security (TLS) implemented in the product or service. The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp.
Notices 342 Limited warranty Lexmark warrants that this product: —Is manufactured from new parts, or new and serviceable used parts, which perform like new parts —Is, during normal use, free from defects in material and workmanship If this product does not function as warranted during the warranty period, contact a Remarketer or Lexmark for repair or replacement (at Lexmark's option).
Notices 343 Warranty service does not include repair of failures caused by: —Modification or unauthorized attachments —Accidents, misuse, abuse or use inconsistent with Lexmark user’s guides, manuals, instructions or guidance —Unsuitable physical or operating environment —Maintenance by anyone other than Lexmark or a Lexmark authorized servicer —Operation of a product beyond the limit of its duty cycle —Use of printing media outside of Lexmark specifications —Refurbishment, repair, refilling or remanufact
Notices 344 The FCC Class B limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
Notices 345 European Community (EC) directives conformity This product is in conformity with the protection requirements of EC Council directives 2004/108/EC, 2006/95/EC, 2009/125/EC, and 2011/65/EU on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility, safety of electrical equipment designed for use within certain voltage limits, the ecodesign of energy-related products, and on the restrictions of use of certain hazardous substances in electrica
Notices 346 (1) cet appareil ne doit pas provoquer d'interférences et (2) il doit accepter toute interférence reçue, y compris celles risquant d'altérer son fonctionnement. Cet appareil a été conçu pour fonctionner uniquement avec l'antenne fournie. L'utilisation de toute autre antenne est strictement interdite par la réglementation d'Industry Canada. En application des réglementations d'Industry Canada, l'utilisation d'une antenne de gain supérieur est strictement interdite.
Notices 347 Česky Společnost Lexmark International, Inc. tímto prohlašuje, že výrobek tento výrobek je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. Dansk Lexmark International, Inc. erklærer herved, at dette produkt overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF. Deutsch Hiermit erklärt Lexmark International, Inc.
Notices 348 Slovensko Lexmark International, Inc. izjavlja, da je ta izdelek v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES. Svenska Härmed intygar Lexmark International, Inc. att denna produkt står i överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG. Model‑specific information The following information applies only to the MS812de printer model.
Notices 349 Japanese VCCI notice European Community (EC) directives conformity This product is in conformity with the protection requirements of EC Council directives 2004/108/EC, 2006/95/EC, and 2011/65/EU on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility, safety of electrical equipment designed for use within certain voltage limits, and on the restrictions of use of certain hazardous substances in electrical and electronic equipment.
Notices 350 Industry Canada (Canada) This device complies with Industry Canada specification RSS-210. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. This device has been designed to operate only with the antenna provided. Use of any other antenna is strictly prohibited per regulations of Industry Canada.
Notices 351 Compliance is indicated by the CE marking. The manufacturer of this product is: Lexmark International, Inc., 740 West New Circle Road, Lexington, KY, 40550 USA. The authorized representative is: Lexmark International Technology Hungária Kft., 8 Lechner Ödön fasor, Millennium Tower III, 1095 Budapest HUNGARY, A declaration of conformity to the requirements of the Directives is available upon request from the Authorized Representative.
Notices 352 Español Por medio de la presente, Lexmark International, Inc. declara que este producto cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE. Eesti Käesolevaga kinnitab Lexmark International, Inc., et seade see toode vastab direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele muudele asjakohastele sätetele. Suomi Lexmark International, Inc.
Index 353 Index Numerics 2100‑sheet tray loading 51, 98, 146 550‑sheet tray installing 29 Symbols [x]‑page jam, clear manual feeder. [250] 272 [x]‑page jam, lift front cover to remove cartridge. [200–201] 264 [x]‑page jam, open tray [x]. [24x] 271 [x]‑page jam, open upper and lower rear door. [231–234] 267 [x]‑page jam, open upper rear door. [202] 266 [x]‑page jam, remove paper, open expander rear door. Leave paper in bin. [41y.xx] 278 [x]‑page jam, remove paper, open finisher rear door.
Index configuring supply notifications 118, 166 configuring supply notifications from the Embedded Web Server 71 connecting to a wireless network using PBC, Push Button Configuration method 37 using PIN, Personal Identification Number method 37 using the Embedded Web Server 38 using wireless setup wizard 37 conservation settings brightness, adjusting 243 conserving supplies 244 Eco‑Mode 74, 120, 168 Hibernate mode 76, 122, 170 Quiet mode 75, 121, 169 Sleep Mode 122 Sleep mode 75, 170 conserving supplies 24
Index factory defaults, restoring 76 FCC notices 343, 345, 348, 349 finding more information about the printer 7 finding printer IP address 87, 134 finisher finishing features 182 supported paper sizes 182 finisher features 182 Finishing menu 229 firmware card 11 flash drive printing from 66, 113, 161 flash drives supported file types 67, 114, 162 font sample list printing 70, 116, 164 Forms and Favorites setting up 89, 136 G General Settings menu 215 green settings Eco‑Mode 74, 120, 168 Hibernate mode 76
Index Load [paper source] with [paper size] [paper orientation] 289 Load [paper source] with [paper type] [paper size] [paper orientation] 289 Load manual feeder with [custom string] [paper orientation] 289 Load manual feeder with [custom type name] [paper orientation] 290 Load manual feeder with [paper size] [paper orientation] 290 Load manual feeder with [paper type] [paper size] [paper orientation] 290 Load staples 288 loading 2100‑sheet tray 51, 98, 146 card stock 58, 105, 153 envelopes 58, 105, 153 le
Index ordering imaging unit 247 maintenance kit 248 roller kit 248 staple cartridges 248 ordering supplies toner cartridges 246 P paper characteristics 176 letterhead 178 preprinted forms 178 recycled 178 selecting 177 setting size 43 setting type 43 storing 176, 179 unacceptable 178 Universal size setting 43, 91, 138 using recycled 243 Paper changes needed 292 paper characteristics 176 paper feed troubleshooting message remains after jam is cleared 314 paper jams avoiding 260 paper jams, clearing behind
Index printer control panel, virtual display using the Embedded Web Server 117 printer hard disk disposing of 77, 123, 171 encrypting 79, 125, 173 installing 22 removing 26 wiping 79, 125, 173 printer hard disk encryption 79, 125, 173 printer hard disk memory erasing 79, 125, 173 printer information where to find 7 printer IP address finding 87, 134 printer is printing blank pages 323 printer messages [x]‑page jam, clear manual feeder. [250] 272 [x]‑page jam, lift front cover to remove cartridge.
Index Remove paper from standard output bin 294 Replace cartridge, 0 estimated pages remain [88.xy] 295 Replace cartridge, printer region mismatch [42.xy] 295 Replace imaging unit, 0 estimated pages remain [84.xy] 295 Replace maintenance kit, 0 estimated pages remain [80.xy] 295 Replace missing or unresponsive fuser [31.xy] 293 Replace roller kit [81.xx] 296 Replace unsupported cartridge [32.xy] 296 Replace unsupported fuser [32.xy] 296 Replace unsupported imaging unit [32.
Index replacing a staple cartridge 254 replacing supplies staple cartridge 254 replacing the toner cartridge 249, 251 Reports menu 197 reserve print jobs 68, 163 printing from a Macintosh computer 69, 116, 164 printing from Windows 69, 116, 164 Restore held jobs? 296 restoring factory default settings 122, 170 roller kit ordering 248 S safety information 5, 6 security modifying confidential print settings 72, 118, 166 Security Audit Log menu 214 security lock 77, 123, 171 security settings erasing 78 secu
Index checking an unresponsive printer 299 contacting customer support 334 solving basic printer problems 299 troubleshooting, display printer display is blank 301 troubleshooting, paper feed message remains after jam is cleared 314 troubleshooting, print envelope seals when printing 302 error reading flash drive 302 held jobs do not print 301 incorrect characters print 303 incorrect margins on prints 318 jammed pages are not reprinted 313 job prints from wrong tray 303 job prints on wrong paper 303 jobs d
