User's Manual

ManualsBrandsLG Electronics USA ManualsComputers & AccessoriesWireless Adapter Card

Model Name : R3

Product Description.

The Module is an OEM module (35x35mm) based on the SMSC DARR83. It is an uncompressed

wireless digital audio transceiver operating in the 2.4GHz, 5.2GHz and 5.8GHz bands. The wireless

audio link supports up to 4 stereo audio streams and comes together with additional features such as:

data encryption, pairing functionality, bi-directional control data messages, low power audio snooze

mode, WLAN detection and Automatic Frequency Allocation. The DARR83 chip itself provides the

basic functions of Audio Processing and buffering, Data Link Layer and Physical Layer. The module

integrates all functionality for a wireless digital audio connection, comprising:

 D

ARR83 Wireless Audio Processor

 2.4GHz/ 5.

2GHz/ 5.8 GHz RF Transceiver

 Embedded Antennas

 Digital audio interfaces (I

S and/or S/PDIF)

 I

C control interface

 26 pins interface connector (FFC) for power, digital audio and control interface and GPIOs

 Built-in 1MB SPI interface Flash 3V 4KB uniform sector

RF Frequency Bandwidth.

2.4GHz: 2400 – 2483.5MHz

5.2GHz: 5150 – 5250MHz

5.8GHz: 5725 – 5875MHz.

RF Performance.

For 2.4GHz application (VCC=3.3V, 25°C)

Parameter Min Typ. Max Units

RF Frequency Range 2400 2483.5 MHz

Number of

RF -Channels

Carries in the spectrum 3

Transmission Power 14 dBm

Frequency

(dynamic or fixed

allocation)

Ch1 2412 MHz

Ch2 2438

Ch3 2464

Channel Spacing 26 MHz

Summary of content (8 pages)

PAGE 1
Model Name : R3 Product Description. The Module is an OEM module (35x35mm) based on the SMSC DARR83. It is an uncompressed wireless digital audio transceiver operating in the 2.4GHz, 5.2GHz and 5.8GHz bands. The wireless audio link supports up to 4 stereo audio streams and comes together with additional features such as: data encryption, pairing functionality, bi-directional control data messages, low power audio snooze mode, WLAN detection and Automatic Frequency Allocation.
PAGE 2
RF Bandwidth Null-to-null Rx Sensitivity Antena Diversity Tx/Rx 22 MHz -83 dBm ON For 5.2GHz application (VCC=3.3V, 25°C) Parameter Min RF Frequency Range 5150 Number of Typ. Max 5250 Units MHz Carries in the spectrum 3 Depending on antenna 9 dBm MHz RF -Channels Transmission Power design Frequency Ch1 5180 (dynamic or fixed Ch2 5210 allocation) Ch3 5240 Channel Spacing RF Bandwidth Null-to-null Rx Sensitivity Antena Diversity Tx/Rx 30 MHz 22 MHz -81 dBm ON For 5.
PAGE 3
Air framing. Addressing : 24Bit. Data Message Size : 32Bytes CRC : 16, 24 and 32Bit POWER - Supply Voltage : 3.1V(Min), 3.3V(Typ), 3.5V(Max) - Peak to Peak Ripple : 100mV(Max). - Operating Temperature : -10C(Min), 25C(Typ), 60C(Max) Evaluation Board Usage The GUI is required to configure the evaluation boards for different applications. Step 1: Double-click on the GUI Icon or shortcut to run the program. Step 2: Read the limited license carefully. Click I Agree to proceed (as shown on the right).
PAGE 4
Connect the USB one by one and select each unique USB port setting for each evaluation board. 1 3 4 2 1) Click the [Refresh] button. 2) Select the EVK ID, for example “A3UNG243”, to access the 4ch EVK connected to the DWAM83 module. 3) Click the [Apply] button. 4) (Optional) If the “A3UNG243”option cannot be selected from the drop down menu, click the [Disconnect] button before repeating steps 1 ~ 3. Once the connection is successful, you should see READY in Module Status. .
PAGE 5
Step 7: Setup your choice of application in the Application Selection (Power-up Settings) For the explanation for the different kinds of application, you can check the help file that is provided with the Evaluation board (EVK). Select desired application (depending on the number of Stereo sources required) Select CU or MU mode Press this button whenever there are any changes in this section to update the module settings Select the Frequency band (2.4GHz or 5.2GHz or 5.
PAGE 6
26Pin Interface PIN # PIN NAME IN/OUT DESCRIPTION 1 VDD Power Input Power: 3.3V. 2 GND Ground GND 3 MCLK In 24.
PAGE 7
Approval Statements Hereby, LG Electronics Inc. declares that this device is in compliance with the essential requirements and other relevant provisions of directive 1999/5/EC. This device complies with Part 15 of the FCC`s Rules. Operation is subject to the following two Conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesirable operation.
PAGE 8