User's Manual

ManualsBrandsLG Electronics USA ManualsComputers & AccessoriesWireless Adapter Card

LG_DWAM82-D module FCC Test manual.doc

Page 1 of 12

LG DWAM82-DB Module for Hx995

FCC Test S/W manual

Module: DWAM82-DB

Date: Jun 03, 2010

Any STS Information is provided “as is” without any express or implied warranty of any kind, including warranties of

merchantability, non-infringement of intellectual property, or fitness for any particular purpose. In no event shall Wireless Sound

Solutions and/or its affiliate companies, or its suppliers liable for any damages whatsoever arising out of the use of or inability to

use the information or the materials. Wireless Sound Solutions, its affiliate companies, and its suppliers further do not warrant the

accuracy or completeness of information, text, graphics, or other items contained within materials. Wireless Sound Solutions, Inc.

All ri

hts reserved. Wireless Sound Solutions, STS and STS-wireless are trademarks of Wireless Sound Solutions.

CONFIDENTIAL FOR

LG & Namuga

ONLY

Summary of content (13 pages)

PAGE 1
NF LG ID E & NT N ON am IAL LY ug FO a R LG_DWAM82-D module FCC Test manual.doc LG DWAM82-DB Module for Hx995 FCC Test S/W manual Module: DWAM82-DB Date: Jun 03, 2010 CO Any STS Information is provided “as is” without any express or implied warranty of any kind, including warranties of merchantability, non-infringement of intellectual property, or fitness for any particular purpose.
PAGE 2
NF LG ID E & NT N ON am IAL LY ug FO a R LG_DWAM82-D module FCC Test manual.doc Date Jun 03, 2010 Revision 0.1 Location SG Change First Draft Author Won Hardware used: 4CH EVK. DWAM82-DB module Test software used: For EvK : 20100603_FCC_DWAM82-D_12288MHz_ForEVK.hex For DWM82-DB module : 20100603_FCC_DWAM82-D_12288MHz_ForEVK.hex CO • • Objective Showing how to change each mode needed for FCC Test.
PAGE 3
NF LG ID E & NT N ON am IAL LY ug FO a R LG_DWAM82-D module FCC Test manual.doc Classification by index number. < 2400MHz ~ 2483.5MHz> RF Band 2.
PAGE 4
NF LG ID E & NT N ON am IAL LY ug FO a R LG_DWAM82-D module FCC Test manual.doc < 5725MHz ~ 5825MHz> RF Band 5.
PAGE 5
NF LG ID E & NT N ON am IAL LY ug FO a R LG_DWAM82-D module FCC Test manual.doc CO Button descriptions on EVK. • • Reset : To reset the whole system and start newly. SPARE_1 : To switch RF band between 2.4G and 5.8G. There is more detailed information at the page 10. • SPARE_3 : To select a index number which has own functionality as written above. There is more detailed information at the page 9.
PAGE 6
NF LG ID E & NT N ON am IAL LY ug FO a R LG_DWAM82-D module FCC Test manual.doc GUI tool descriptions. - How to update Serial-Com SW for ATMEL MCU. • • • Go to “USB Port Settings” box at the bottom of GUI tool Select the triangle button. CO • Double click the GUI tools named “DARR82_GUI_demo_5Ghz_2_6_1. exe” Once the photos as shown left appear, please click “I Agree” button.
PAGE 7
NF LG ID E & NT N ON am IAL LY ug FO a R LG_DWAM82-D module FCC Test manual.doc • • At this time, select “USB1(A3SEB7YE) and press the “Apply” button to confirm the settings. Do not pay any attention to USB serial number. It may different from each computer. • You could see that the port of USB1 Is open. • • Go to Tools on the top of GUI Select “EVK Upgrade” under Tools’s submenu. Please press the button as shown left .
PAGE 8
NF LG ID E & NT N ON am IAL LY ug FO a R CO LG_DWAM82-D module FCC Test manual.doc • As shown left, if the button of “Change Loadfile” is activated, please select the serial_com_V_CU_005_5_8G_FCC. hex located at “\SW\For_EVK\” • And then press the “Start Loading” button to update the EVK. • Once this update process is successfully done, success message of “Check CRC16” will be shown up and disappear a moment later. • Go to Tools menu on the top of GUI and select it.
PAGE 9
NF LG ID E & NT N ON am IAL LY ug FO a R LG_DWAM82-D module FCC Test manual.doc CO < Index switching at either 2.4GHz or 5.8G> • The pop up window will come out after you select “RS232 Info”. • If you look into the red circle, you can see the current index number. Index 0 means the idle status. • At this time, please press “Spare 3” button to change current index. • Every time you press “Spare 3 button, the Current Index number will change.
PAGE 10
NF LG ID E & NT N ON am IAL LY ug FO a R LG_DWAM82-D module FCC Test manual.doc < Band switching between 2.4G and 5.8G> The captured photo shows how to change RF Band from 5.xGHz to 2.xGHz. • Press “Spare 1” button on the EVK => Current Index will set to “0” • The index from 0x01 to 0x18 will be available to select by pressing “Spare 3” button.
PAGE 11
NF LG ID E & NT N ON am IAL LY ug FO a R LG_DWAM82-D module FCC Test manual.doc - How to update EEPROM on DWAM82-DB. • Go to “Tools” at the top menu and select “Program 8052 Firmware”. • • 1) Press “Erase Button” 2) Check the message of “Completed successfully”. 3) Make sure the values are same as snap-shot. 4) Search and select the hex file ou need to update with. • • Press “Download button” to start to update EEPROM.
PAGE 12
NF LG ID E & NT N ON am IAL LY ug FO a R LG_DWAM82-D module FCC Test manual.doc The bar should be in progress. • After successful update, message will show like left snapshot. • CRC value may be different from each software. • Press “Reset ” button on EVK.
PAGE 13
This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference received. 2. This device must accept any interference received. Including interference that may cause undesired operation. FCC WARNING This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual.