Order Number : GETEC-C1-09-198 FCC Class B Certification Test Report Number : GETEC-E3-09-112 Page 1 / 1 APPENDIX G : USER’S MANUAL EUT Type: Full HD Projector FCC ID.
Model number Serial number : : LG LCOS PROJECTOR Please read this manual carefully before operating your set. Retain it for future reference. Record model number and serial number of the set. See the label attached on the bottom of the set and quote this information to your dealer when you require service.
LCOS PROJECTOR Warning - Class B (b) For a Class B Digital device or peripheral, the instructions furnished the user shall include the following or similar statement, placed in a prominent location in the text of the manual: NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residemtial installation.
Contents Contents Safety Instructions ....................................4 Names of parts Main Body .......................................................7 Connecting Part ..............................................8 Control Panel ..................................................9 Remote Control ...............................................10 Installing Batteries...........................................10 Projector Status Indicators..............................11 Accessories.....................
Safety Instructions Safety Instructions Please take note of the safety instructions to prevent any potential accident or misuse of the projector. ➟ Safety Instructions are given in two forms as detailed below. WARNING : The violation of this instruction may cause serious injuries and even death. NOTES : The violation of this instruction may cause light injuries or damage to the projector. ➟ After reading this manual, keep it in the place that the user can access easily.
Power ENGLISH Safety Instructions WARNING Do not plug-in too many items into one power outlet. It may result in overheating of the outlet and create a fire hazard ! Power Never touch the power plug with a wet hand This may cause an electric shock hazard ! NOTES Hold the plug firmly when unplugging. If you pull the cord, it may be damaged. Prevent dust collecting on the power plug pins or outlet.
Safety Instructions Using WARNING If the projector is in a room that experiences a gas leak, do not touch the projector. It can cause a fire or a burn by a spark. Do not drop the projector or allow impact shock. Don’t look at the laser beam directly as it can cause eye damage! This may cause mechanical failure or personal injury ! Always open the lens door or remove the lens cap when the projector lamp is on. Using NOTES Do not place heavy objects on top of projector.
ENGLISH Names of parts Names of parts Main Body * The projector is manufactured using high-precision technology. You may, however, see on the Projector screen tiny black points and/or bright points (red, blue, or green). This can be a normal result of the manufacturing process and does not always indicate a malfunction.
Names of parts Connecting Part Rear remote control sensor USB(SVC Only) RGB IN Kensington Security System Connector (Refer to page 15) VIDEO COMPONENT IN AC IN S-VIDEO HDMI IN 1/2 8 Control Panel
ENGLISH Names of parts Control Panel POWER Button Turn ON/OFF the projector. INPUT Button Switches to RGB, HDMI, Video, S-Video or Component mode. OK Button Checks present mode and saves the function changes. / / / Button Adjusts functions of menus MENU Button Selects or closes menus. AUTO Button It automatically corrects the position and shaking of the image in RGB mode.
ENGLISH Names of parts Projector Status Indicators * Lamp indicator, operation indicator and temperature indicator at the top of the projector show the user the operating status of the projector.
Names of parts Accessories LIGHT 1.5V 1.5V Remote Control Power Cord 2 Batteries Owner’s manual Polishing Cloth Filter Optional Extras * Contact your dealer to purchase these items. * The lamp is consumable and needs to be replaced with a new one when it is burned out. Contact your dealer or service center for a replacement lamp. * Optional parts can be changed without notice to improve the quality of the product, and new optional parts can be added.
ENGLISH Installing and Composition Installing and Composition Installation Precautions Provide proper ventilation for this projector. ● The projector is equipped with ventilation holes(intake) ●Do not place the projector on a carpet, rug or other ●Never push projector or spill any kind of liquid into the ●Leave an adequate distance(30cm/12 inches or more) on the bottom and ventilation holes(exhaust) on the front. Do not block or place anything near these holes.
Installing and Composition Positioning the Projector 1.Place the projector on a sturdy and horizontal surface. 2.Place the projector the desired distance from the screen. The distance between the projector and the screen determines the actual size of the image. 3.Position the projector so that the lens is set at a right angle to the screen. If the projector is not set at a right angle, the screen image will be crooked. Although, slight angles can be counteracted using the Keystone adjustement.
Installing and Composition Turning on the Projector 1. Make sure the power cord is connected correctly. 2. Remove the lens cap. If it is left on, it could become deformed due to the heat produced by the projection lamp. 3. Press the POWER button on the remote control or back cover. ● An image will appear after the operation deco LED turns (Blue (flashing)). ● Press the INPUT button on the remote control or the INPUT button on the control panel to select the input signal you want.
ENGLISH Installing and Composition Focus and Position of the Screen Image When an image appears on the screen, check if it is in focus and fits the screen properly. Focus ring Zoom ring ● To adjust the focus of the image, rotate the focus ring which is the outer ring on the lens. ● To adjust the size of the image, rotate the zoom ring which is the under ring on the lens. When you need to move the screen image up or down, use the Lens shift dial on the projector to adjust the height as shown below.
Connection Connection Connecting to a Desktop PC * You can connect the projector to a computer with VGA, SVGA, XGA and SXGA output. * Refer to page 30 for resolutions the projector supports. < How to connect > Connect the RGB IN of the projector and the computer output port with a computer cable. * You may have to change the resolution that your PC exports to one supported by the projector. Refer to page 30. This projector may not support output from laptops when the laptop screen is on.
ENGLISH Connection Connecting to a DVD Player * Depending on the equipment, the component output jacks (Y, PB, PR) of the DVD Player may be labeled as Y, Pb, Pr/Y, B-Y, R-Y/Y, Cb, Cr. < How to connect > Component cable a.Connect the DVD Player component cable to the Y, PB and PR of the COMPONENT IN of the projector. * When connecting the component cable, match the jack colors with the component cable.(Y=green, PB=blue, PR=red) (R) AUDIO (L) PB Y PR b.
Information Supported Monitor Display * The following table lists the display formats supported by the projector. Sources Format Vertical Freq.(Hz) Horizontal Freq.(kHz) * If the projector does not support the input signal, “Out of Range” message appears on the screen. * The projector supports DDC1/2B type as Plug & Play function. (Auto recognition of PC monitor) * The Synchronization input form for horizontal and vertical frequencies are Separate.
ENGLISH Information Maintenance * The projector needs little maintenance. You should keep the lens clean because any dirt or stains may appear on the screen. If any parts need to be replaced, contact your dealer. When cleaning any part of the projector, always turn the power off and unplug the projector first. Cleaning the lens Clean the lens whenever you notice dirt or dust on the surface of it. Wipe the lens surface gently with an air spray or a soft, dry lint-free cloth.
Information Replacing the Lamp Lamp Replacement The change interval of lamp may depend on the use environment of Projector. You can see the used lamp time in the CHECKING LAMP TIME section of the Menu (page.29). You must replace the lamp when: ● The projected image gets darker or starts to deteriorate. The lamp indicator is red. The message “Replace the lamp” appears on the screen when turning the projector on.
ENGLISH Information Replacing the Lamp 1 Turn off the projector and unplug the power cable. Carefully place on a cushioned surface. 2 Unscrew the screw from the lamp cover using a screwdriver. (Allow the lamp to cool for 1 hour before removing the used lamp from the projector.) Lamp case screw 3 After lifting the lamp cover off, remove the two retaining screws on the lamp case with a screwdriver. 4 Screws Lift the lamp up from the projector.
Information Regarding the projector lamp control WARNING 34 ● Don’t turn off the projector at least in 5 minutes after activating it. - The frequent On/Off changes may cause the lamp to deteriorate. ● Don’t pull out the power cord while the projector or the cooling fan are running. - It may shorten the life of the lamp. ● The life-span of depends on the environment its used in and how well its treated. ● The projector uses a high pressure mercury lamp.
ENGLISH Information Specifications MODEL AF115 (AF115-JS) Resolution 1920(Horizontal) x 1080(Vertical)pixel Horizontal / Vertical Ratio 16 : 9 (horizontal:vertical) LCOS panel size 0.61 inches Screen size (Projection distance) Tele : 30 ~ 300 inches(1.6 ~ 16.4m) Projection off-set ratio 120% Remote control distance 12m Wide : 30 ~ 300 inches(0.9 ~ 9.1m) Zoom ratio 1:1.8 Video compatibility NTSC/PAL/SECAM/NTSC4.43/PAL-M/PAL-N/PAL 60 Power AC 100 - 240V~50/60Hz, 3.0A-1.
Regulatory Information cont. FCC Compliance Statement respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. This equipment has been tested and found to comply within the limits of a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. NOTICE The regulations are applied only to the products with the ID LABEL indicating specific requirements.
Regulatory Information cont. Why do we have environmentally labelled computers? In many countries, environmental labelling has become an established method for encouraging the adaptation of goods and services to the environment. With the growing manufacture and usage of electronic equipment throughout the world, there is a recognized concern for the materials and substances used by electronic products with regards to their eventual recycling and disposal.
Regulatory Information cont. • exception. Mercury is, for the time being, permitted in the back light system of flat panel monitors as there today is no commercially available alternative. TCO aims on removing this exception when a mercury free alternative is available.
Regulatory Information cont. operation worldwide. Many parts will be reused and recycled, while harmful substances and heavy metals are treated by an environmentally friendly method. If you want to find out more information about our recycling program, please contact your local LG vendor or a corporate representative of LG.
Regulatory Information cont. Italiano respetan el medio ambiente siempre teniendo en cuenta aspectos sociales, económicos y medioambientales. Informazioni per la tutela dell’ambiente La LGE. ha annunciato nel 1994 la cosiddetta 'LG Declaration for a Cleaner Environment' (Dichiarazione di LG a favore di un ambiente più pulito), un ideale che da allora funge da principio ispiratore della gestione aziendale.
Regulatory Information cont. especificamente o conceito de favorável ao ambiente. Reduzimos os materiais perigosos contidos em nossos produtos. Por exemplo, não há cádmio em nossos monitores. Informatie met betrekking tot recycling Deze monitor bevat materialen die schadelijk zouden kunnen zijn voor het milieu. Het is belangrijk dat deze monitor aan het einde van zijn levensduur wordt gerecycled. Informações relacionadas à reciclagem Este monitor pode conter peças que podem representar riscos ao ambiente.
Regulatory Information cont. ÕÂÓ·ıÓ‰ËÏÓ ÛÚËÎËÁËÓ‚‡Ú¸ ÏÓÌËÚÓ ÔÓÒΠËÒÔÓθÁÓ‚‡Ìˡ. KÓÔÓ‡ˆËˇ LGE Ô‡·‡Ú˚‚‡ÂÚ ‚Ò ·‡ÍÓ‚‡ÌÌ˚ ÏÓÌËÚÓ˚ Ò ÔÓÏÓ˘¸˛ ˝ÍÓÎӄ˘ÂÒÍË ÔËÂÏÎÂÏÓ„Ó ÏÂÚÓ‰‡ ÛÚËÎËÁ‡ˆËË ÓÚıÓ‰Ó‚. œÓ ‚ÒÂÏÛ ÏËÛ ‰ÂÈÒÚ‚Û˛Ú ÒËÒÚÂÏ˚ ÛÚËÎËÁ‡ˆËË ÓÚıÓ‰Ó‚ Ë ‚ÓÁ‚‡Ú‡ ËÒÔÓθÁÓ‚‡ÌÌÓÈ ÔÓ‰Û͈ËË. ÃÌÓ„Ë ÍÓÏÔÓÌÂÌÚ˚ ·Û‰ÛÚ ‚ÚÓ˘ÌÓ ËÒÔÓθÁÓ‚‡Ì˚ Ë ÛÚËÎËÁËÓ‚‡Ì˚, ‚ ÚÓ ‚ÂÏˇ Í‡Í ‚‰Ì˚ ‚¢ÂÒÚ‚‡ Ë ÚˇÊÂÎ˚ ÏÂÚ‡ÎÎ˚ ·Û‰ÛÚ Ó·‡·ÓÚ‡Ì˚ Ò ÔÓÏÓ˘¸˛ ˝ÍÓÎӄ˘ÂÒÍË ÔËÂÏÎÂÏÓ„Ó ÏÂÚÓ‰‡.
Regulatory Information cont. WEEE un bidone della spazzatura barrato da una croce significa che il prodotto è coperto dalla direttiva europea 2002/96/EC. 2.Tutti i prodotti elettrici ed elettronici dovrebbero essere smaltiti separatamente rispetto alla raccolta differenziata municipale, mediante impianti di raccolta specifici designati dal governo o dalle autorità locali. 3.
Regulatory Information cont. 4.Wilt u meer informatie over de verwijdering van uw oude toestel? Neem dan contact op met uw gemeente, de afvalophaaldienst of de winkel waar u het product hebt gekocht. eller de lokale myndigheder. 3.Korrekt bortskaffelse af dit gamle apparat er med til at forhindre mulige skadevirkninger på miljøet og menneskelig sundhed. 4.
Regulatory Information cont.
Regulatory Information cont.
