User's Manual

ManualsBrandsLG Electronics USA ManualsComputers & AccessoriesPERSONAL COMPUTER

System Expansion78

ⓞ Turn on the computer and monitor.

ⓟ

Press [Delete]key when the logo screen appears.

ⓠ The CMOS Setup Utility opens.

ⓡ

Use arrow

>Ⓑ@>Ⓒ@>⒵@

, and

>Ⓐ@

keys to select Standard CMOS Features, and

press [Enter].

Hard disk drive setup

Phoenix-Award BIOS CMOS Set up Utility

Ě Standard CMOS Features Ě PC Health Status

Ě Advanced BIOS Features Ě Frequency/Voltage Control

Ě Advanced Chipset Features Load Optimized Defaults

Ě Integrated Peripherals Set Password

Ě Power Management Setup Save & Exit Setup

Ě PnP/PCI Configurations Exit Without Saving

Esc : Quit êëè é : Select ltem

F10 : Save & Exit Setup

Virus Protection, Boot Sequence...

Summary of content (11 pages)

PAGE 1
Hard disk drive setup ⓞ Turn on the computer and monitor. ⓟ Press [Delete]key when the logo screen appears. ⓠ The CMOS Setup Utility opens.
PAGE 2
ⓢ Use arrow >Ⓑ@ >Ⓒ@ >⒵@, and >Ⓐ@ keys to select IDE Channel 0 Slave, and press [Enter]. Phoenix-Award BIOS CMOS Set up Utility Standard CMOS Features Data (mm:dd:yy) Time (hh:mm:ss) Ě IDE Channel 0 Master Ě Ě IDE IIDEChannel Channel0 0Slave Slave Ě IDE Channel 1 Master Ě IDE Channel 1 Slave Drive A Drive B Video Halt On XXX, XXX, XXXX XX, XX, XX Press EnterXXXXXMB Press PressEnter Enter None None Press Enter None Press Enter None X.XXM, X.Xin None EGA/VGA All, But Keyboard.
PAGE 3
Hard disk setup (Hard disk with factory default setting) Be careful, Using to divide partition delete data in a selected driver. ⓞ Click [Start] and [Run]. ⓟ Type 'diskmgmt.msc' and press [OK]. ⓠ If the following window appears, select disk1. Click right button on the mouse to select New partition. ⓡ Click [Next] if the following message appears.
PAGE 4
ⓢ Select a partition and click [Next]. ⓣ Select the maximum size and click [Next]. A selected space of the disk will be available to use. ⓤ Click [Next] after selecting a drive value.
PAGE 5
ⓥ If the following window appears, select File system, Allocation unit size and Volume label ,and click [Next]. ⓦ New Partition Wizard is complete, click [Finish]. ⓧ After the format is complete, the hard disk operates normally.
PAGE 6
-6. Installing expansion cards When you are using the computer, you may need to install expansion cards to improve funtionality. The following instruction describes how to install expansion cards. ⓞ Refer to Opening the computer case to open the computer case cover. ⓟ Remove the capas shown on the picture. ã Always use a screwdriver to open the case cover. There is the risk of injury. ã In order not to be injured when disassembling the computer, wear the gloves. ⓠ Remove 2 screws as shown on the picture.
PAGE 7
ⓢ Hold the expansion card with both hands and align the expansion card and slot. Push down evenly to insert the card into the slot. ã Incorrect installation of an expansion card may damage the main board and result in a computer malfunc tion. Expansion slot ⓣ Fasten a screw after installing a metal bracket. metal bracket ã Using the computer without closing the case may result in fire, electric shock, injury, and/or damage to the computer. ⓤ Close the cap in the same position as you removed it.
PAGE 8
Specifications *(* (0 PRGHO Ú Specifications below differ depending on the models. CPU System memory Intel Pentium 4 / Celeron mPGA478 type (2.4GHz or above) 256MB (up to 2.0 GB) - If built-in VGA is used, maximum 16MB and minimum 1MB is applied for Video Frame buffer in DOS Mode, but Windows Mode automatically manages the video memory (up to 96MB depending on System Memory size). Cache memory L1: 8KB/16KB or above, L2: 128KB/256KB/512KB/1024KB or above.
PAGE 9
PAGE 10
PHPR memo 87
PAGE 11
PHPR 88 memo