User's Manual

ManualsBrandsLG Electronics USA ManualsComputers & AccessoriesPersonal Computer

System Expansion70

The main board configuration, memory socket, and the shape of memory may be

different depending on the model.

ⓞ Remove the screws on the rear of the

computer, and open the computer case.

ⓟ Pull the latch on each side of a memory socket to release the memory.

Replacing the memory

latch

ãBefore opening the case, turn off the

computer and peripheral devices,

and remove the power cords.

Note

ⓞ

Pull the latch on each side of a memory socket.

ⓟ

Align the notch at the bottom of the

memory with a protrusion in the middle

of the socket, and then insert the

memory straight down.

Installing a memory

ã For dual channel system, each mem

ory should be installed in independent

slot(1&3 slot or 2&4 slot) when using

DDR Memory

It is recognized as a single channel if

there is a difference between dual

channel 1 and 3, 2 and 4.

Note

℘

ℙ

ℚ

ℛ

Firmly push the latch to lock the memory.

Summary of content (15 pages)

PAGE 1
Replacing the memory The main board configuration, memory socket, and the shape of memory may be different depending on the model. ⓞ Remove the screws on the rear of the computer, and open the computer case. Note ãBefore opening the case, turn off the computer and peripheral devices, and remove the power cords. ⓟ Pull the latch on each side of a memory socket to release the memory. latch Installing a memory ⓞ Pull the latch on each side of a memory socket.
PAGE 2
Checking the size of the installed memory The computer automatically recognizes the newly installed memory; therefore, you do not need to change the system setup. Follow the instruction below to check the size of the installed memory. ⓞ Connect the power cord and other devices, and turn on the computer and monitor. The following screen appears to inspect the status of the computer. ⓟ If the following screen appears, press [Esc]. POST screen appears.
PAGE 3
6-6. Adding a hard disk drive Your computer supports up to 4 E-IDE controllers and 2 hard disk drives. Before adding a hard disk drive The following instruction describes the most typical configuration where your computer already has a master hard disk drive and you are adding a slave hard disk drive. Note ã Check and write down the jumper settings, size, and number of cylinders, heads, and sectors of the hard disk drive where you can refer to when you use the system setup.
PAGE 4
ⓞ Open the CD-ROM drive by using a sharp pin into the emergency hole as shown on the picture No ℘. Remove the by pushing it to the direction of the arrow as shown on the picture No ℙ. ℘ ℙ Turn off the computer and remove the cable when disassembling the computer. There is a risk of an electrical shock. ⓟ Refer to the page 62 to remove the cover. Remove the 4 screws from the hard case and remove the case to the direction of the arrow.
PAGE 5
ⓡ Connect the power cable connector and the signal cable connector to the new hard disk you want to replaced with and fasten 2 screws in the hard disk case. power cable signal cable ℘ ℙ Note ã Align the connector in a right position as show on the picture. Actual appearance of the connector may be different from the picture, check the right position. ⓢ Fasten 4 screws in the hard case after connecting the cables. Refer to the page 62 to close the cover. Install the CD-ROM tray.
PAGE 6
Hard disk drive setup ⓞ Turn on the computer and monitor. ⓟ Press [Delete]key when the logo screen appears. ⓠ The CMOS Setup Utility opens. 3KRHQL[ $ZDUG %,26 &026 6HW XS 8WLOLW\ Ě 6WDQGDUG &026 )HDWXUHV Ě 3& +HDOWK 6WDWXV Ě $GYDQFHG %,26 )HDWXUHV Ě )UHTXHQF\ 9ROWDJH &RQWURO Ě $GYDQFHG &KLSVHW )HDWXUHV /RDG 2SWLPL]HG 'HIDXOWV Ě ,QWHJUDWHG 3HULSKHUDOV 6HW 3DVVZRUG Ě 3RZHU 0DQDJHPHQW 6HWXS 6DYH ([LW 6HWXS Ě 3Q3 3&, &RQILJXUDWLRQV ([LW :LWKRXW 6DYLQJ (VF 4XLW êëè é 6HOHFW OWHP ) 6DYH
PAGE 7
ⓢ Use arrow >Ⓑ@ >Ⓒ@ >⒵@, and >Ⓐ@ keys to select IDE Channel 0 Slave, and press [Enter]. Phoenix-Award BIOS CMOS Set up Utility Standard CMOS Features Data (mm:dd:yy) Time (hh:mm:ss) Ě IDE Channel 0 Master Ě Ě IDE IIDEChannel Channel0 0Slave Slave Ě IDE Channel 1 Master Ě IDE Channel 1 Slave Drive A Drive B Video Halt On XXX, XXX, XXXX XX, XX, XX Press EnterXXXXXMB Press PressEnter Enter None None Press Enter None Press Enter None X.XXM, X.
PAGE 8
Hard disk setup (Hard disk with factory default setting) Be careful, Using to divide partition delete data in a selected driver. ⓞ Click [Start] and [Run]. ⓟ Type 'diskmgmt.msc' and press [OK]. ⓠ If the following window appears, select disk1. Click right button on the mouse to select New partition. ⓡ Click [Next] if the following message appears.
PAGE 9
ⓢ Select a partition and click [Next]. ⓣ Select the maximum size and click [Next]. A selected space of the disk will be available to use. ⓤ Click [Next] after selecting a drive value.
PAGE 10
ⓥ If the following window appears, select File system, Allocation unit size and Volume label ,and click [Next]. ⓦ New Partition Wizard is complete, click [Finish]. ⓧ After the format is complete, the hard disk operates normally.
PAGE 11
6-7.Installing expansion cards When you are using the computer, you may need to install expansion cards to improve funtionality. The following instruction describes how to install expansion cards. ⓞ Refer to Opening the computer case to open the computer case cover. Always use a screwdriver to open the case cover. There is the risk of injury. ⓟ Remove 3 screws as shown on the picture Remove the slot using driver where the expension card is located.
PAGE 12
ⓠ Hold the expansion card with both hands and align the expansion card and slot. Push down evenly to insert the card into the slot. Incorrect installation of an expansion card may damage the main board and result in a computer malfunction. Expansion slot ⓡ Fasten a screw to fasten the metal bracket of the card to the computer case. Metal bracket Using the computer without closing the case may result in fire, electric shock, injury, and/or damage to the computer.
PAGE 13
Specifications *)* PRGHO Ú Specifications below differ depending on the models. CPU System memory Cache memory L1: 8KB/16KB or above, L2: 128KB/256KB/512KB/1024KB or above. Hard disk drive 40GB or above (E-IDE type) Keyboard PS/2 keyboard (104keys) Mouse PS/2 mouse or USB (ball / wheel) Video Integrated or external AGP graphic Sound Built-in AC'97 audio. Support MIC-IN, SPEAKER-OUT and LINE-IN.(Support virtual 5.
PAGE 14
PAGE 15
PHPR 84 memo