Running Norton Antivirus Click [Start] [All programs] [Norton Antivirus] [Norton AntiVirus2005]. Click [Scan for virus] and select an item to scan. Norton AntiVirus is scanning virus. Note If any virus is detected, click [Fix] to repair. Click [Finish]. Virus scanning is complete.
MEMO 47
. System setup System setup means storing hardware configuration information of the computer in CMOS RAM. Through the System Setup, the computer gets various information -date of the day, time, memory capacity, H/D capacity and its type. System Setup is to set passwords, to change booting orders, and to add new peripheral devices. 3-1. Entering System Setup Booting with a USB drive (Page 50). Setting a password (Page 52). Deleting or changing a password (Page 53). Initializing system setup (Page 55).
Note Cursor Pad These keys are used to move the cursors on the monitor screen up, down, right, and left. When the Num Lock button is off on the numeric keypad, the numeric keypad functions the same as the cursor keypad. Turn on the computer and the monitor. While the LG logo screen is on, press [Delete] key. The initial setup screen will appear.
Booting with a USB Drive A booting with a USB device (USB-FDD, USB-ZIP, USB-CD-ROM, or USB-HDD) proceeds as follows Booting with a USB-FDD, USB-ZIP, or USB-CD ROM Execute the initial screen of System Setup, and select Advance Bios Features by pressing , and keys. Then, press [Enter] key When the following screen appears, select First Boot Device by pressing keys.
Booting with a USB-HDD Execute the initial screen of System Setup, and select Advance Bios Features by pressing , and keys. Then, press [Enter] key When the following screen appears, select Hard Disk Boot priority by pressing keys.
3-3. Setting a Password To prevent other users from changing computer settings, you can register a password. A password can be registered during booting or System Setup. Without the registered password, if any, access to the system will be denied. Write down and keep your password in a safe place. Execute the initial screen of System Setup and select Advanced Bios Features by pressing , and keys. Then, press [Enter] key.
When the following message appears on the screen, input the password and press [Enter] key. The password must be alphanumeric and not exceed eight digits. Enter Password : When asked to confirm the password, input the password again and press [Enter] key. Confirm Password : To save changes in System Setup, press [F10]. When the following message appears, press [Enter] key to restart the computer. SAVE to CMOS and EXIT(Y/N)? Y 3-4.
Changing the Password Change the password in the same procedure as that of password setting. Deleting the Password Select Set Password by pressing , and of the Setup menu, and press the [Enter] key.
3-5. Initializing System Setup If you changed the system setup by mistake, it can be recovered to the default setting. Execute the initial screen of System Setup, and select the Load Optimized Defaults item by pressing arrow keys. Then, press [Enter]. When the following message appears on the screen, press [Y] and [Enter]. System setup will be return to the factory setting. Load Optimized Defaults (Y/N) ? Y To save the change in System Setup, press [F10].
3-6. Deciding the Temporary Booting Orders The following instruction explains a way to decide the temporary booting orders without affecting CMO setup. Turn on the computer and the monitor. While LG logo screen is on, press [F12]. Selected device from the Boot menu will start the system. Note The menus may differ by product model : USB-FDD, USB-ZIP, USB-HDD, and USB-CDROM. Bootable devices will be displayed only when they are equipped in before turning the computer on.
3-7. Setting the Power Saver Mode Regardless of BIOS setup, you can use the Power Saver mode in Windows as follows. Select [Start] [Control Panel] [Switch to Classic View]. Double-click the Power option icon on the Control Panel window. After setting Power Scheme items in the Power Schemes tab, click the [OK] button. TWhen the device connected to the computer does not support Power Saver functions, the Standby mode or Hibernate mode may not be properly function.
3-8. Using Hyper-Threading Feature The Hyper-threading feature improves the performance of the CPU greatly as if two CPUs were running. This feature is especially efficient for multimedia tasks such as games and graphic jobs. Hyper-threading is supported only by the CPU with Hyper-Threading (HT) feature. Check the "Intel" sticker on the side of the computer to see if the CPU supports hyper-threading. Execute the initial screen of System Setup, and select Advanced Bios Features by pressing , and keys.
MEMO 59
4.System Recovery You can restore the system in two ways depending on the current status of the system. However, to restore the hard disk, you need to back up necessary software and data files in advance. After completing Windows installation, you need to register the User Properties when booting the system as if you did your new computer. Installation with Recovery CD Installation Back up the data stored in the computer. Insert the Restore CD in the CD-ROM drive. When "Press any key to boot from CD...
Installation of Windows XP Upgrade If Windows XP is already installed on the hard disk, you can upgrade existing Windows XP without formatting the hard disk In the case that Windows XP is already running on the hard disk, upgrade Windows XP as follows. For Windows users Turn on the system where Windows XP is installed. Click the [Start] and [Run] button. Insert the Restore CD, and input D:\i386\winnt32.exe/unattend. Then, click the [OK] button. (When the CD-ROM drive is D drive.
5. Reinstallation of Drivers 5-1.Reinstalling Printer Driver You must install the printer driver after connecting the printer. Windows XP can automatically detect printer drivers. However, if Windows XP does not detect your printer driver, install the printer driver as follows. Select [Start] [Control Panel] [Class Desktop]. Double click the [Printer and Fax] on the Control Panel window. When the following screen appears, click the [Add Printer] button.
When the following screen appears, check the connection type of the printer local or network. Then, select a printer and click the [Next] button. New Printer Detection screen will appear. Click the [Next] button. When Set Printer Port screen appears, select LPT1 or LPT2 before clicking the [Next] button. Select the manufacturer and model of your printer on the Select Printer screen. If your printer came with an installation disk, click [Have Disk]. If not, just click the [Next] button.
When [Have Disk] is selected. Insert the diskette or driver CD in the driver and click the [OK] button. When [Next] is selected Name the printer, and click the [Next] button. When Print Test Page screen appears, click the [Yes] and [Next].
After the test page is properly printed out, click the [OK] button. When the following screen appears, check the printer and click the [Finish] button. Now, the printer has been added. .
5-2.Reinstalling Sound Driver You must install a sound driver to listen to music files and CDs on the computer. A sound driver basically comes out with the computer. If it has to be reinstalled, however, follow the process below. Turn on the computer and the monitor. Insert LG GILJABI CD in the CD-ROM driver. Select the sound driver to install from the list. The driver installation process will start. Follow instructions on the screen.
5-3.Reinstalling Video Driver The video driver displays on the monitor data stored on the computer. The video driver is included in basic specification of the computer. However, in the case that it is necessary to reinstall the video driver, carry out the following process. Turn on the computer and the monitor. Insert LG GILJABI CD in the CD-ROM driver. Select the video driver to install from the list. The driver installation process will start. Follow instructions on the screen.
6.System Expansion 6-1. Opening the computer case Always consult with your service representatives before opening the computer case. Note the following when opening the computer cover. Quit all programs in use. Turn off the computer and the monitor before disconnecting the power. Keep magnetic tools (for example, drivers) away from the computer since parts inside the computer are electrically charged and sensitive to magnetic force. Install the computer in a clean, easily-accessible place.
