Technical Specification (TM03LNCAHK0) 1/13
History Ver. Date 1.0 2016.12.
Contents 1. Product Introduction..................................................................................................... 4 1.1 Block Diagram .................................................................................................... 5 1.2 Environmental Specifications.............................................................................. 5 1.3 Electrical Specifications ...................................................................................... 5 1.3.
1. Product Introuction The TM03LNCAHK0 are designed for the automotive industry. They support LTE and CDMA air Interface standards. The TM03LNCAHK0 are based on the Qualcomm MDM9628 wireless chipsets and support the following bands. Table 1. Supported Band Region Canada LTE B2/B4/B5/B17 WCDMA B2/B5 Band 1.1 Block Diagram Figure 1.1.
1.2 Environmental Specifications The environmental specification for operating and storage of the TM03LNCAHK0 are defined in the the table below. Table 2. Environmental Specifications Parameter Temperature Range Operating Temperature -40℃ to 85℃ Storage Temperature -40℃ to +90℃ Humidity 95% or less 1.3 Electrical Specifications This section provides details for some of the key electrical specifications of the TM03LNCAHK0 embedded modules. 1.3.
1.3.2 Current Consumption Table 4. TM03LNCAHK0 Current Consumption Mode Parameter Typical Max Band2, Max TX Output /Full RB 600 650 Band4, Max TX Output /Full RB 600 650 Band5, Max TX Output /Full RB 550 600 Band17, Max TX Output /Full RB 550 600 Band2 600 650 Band5 550 600 LTE Idle, Registered 1.8 2.2 mA WCDMA Idle, Registered 1.8 2.2 mA LTE Sleep Mode, Average Current 1.8 2.2 mA WCDMA Sleep Mode, Average Current 1.8 2.2 mA LTE WCDMA Units mA mA 1.
1.4.2 Mechanical Drawing 1.4.2.
2. Pin Definitions Table6.
3. RF Specification The specifications for the LTE and CDMA interfaces are defined. TM03LNCAHK0 is designed to be compliant with the standard shown in the table below. Table20. Standards Compliance Technology Standards LTE • 3GPP Release 8 WCDMA • 3GPP Release 9 3.1 LTE B2, B4, B5, B17 Specification 3.1.1 LTE TX Output Power The Maximum / Minimum Transmitter Output Power of the TM03LNCAHK0 are specified in the following table. Table21.
Table22.
3.2.2 WCDMA RX Sensitivity The Receiver Sensitivity of the TM03LNCAHK0 are specified in the following table. Table24. Conducted RX (Receive) Sensitivity –WCDMA Bands Item Method (DL CH) Specification Measure BER of Low Channel (CH= 10563) WCDMA B2 Power Level Measure BER of Low Channel (CH= 10700) Measure BER of Low Channel (CH= 10837) Measure BER of Low Channel (CH=25) WCDMA B5 Power Level Measure BER of Low Channel (CH=600) Measure BER of Low Channel (CH=1175) 11/13 0.1% @≤-106dBm 0.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. RF Exposure Statement The antenna(s) must be installed such that a minimum separation distance of at least 20 cm is maintained between the radiator (antenna) and all persons at all times. This device must not be co-located or operating in conjunction with any other antenna or transmitter.
RSS-GEN, Sec. 8.3 This radio transmitter (identify the device by certification number, or model number if Category II) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
