USER GUIDE (LG-LP1000)
FCC RF EXPOSURE INFORMATION WARNING! Read this information before using your phone In August 1996 the Federal Communications Commission (FCC) of the United States with its action in Report and Order FCC 96-326 adopted an updated safety standard for human exposure to radio frequency electromagnetic energy emitted by FCC regulated transmitters. Those guidelines are consistent with the safety standard previously set by both U.S. and international standards bodies.
CHAPTER 1.
CHAPTER 2. BASIC FUNCTIONS Turning the Phone On and Off 1. Connect the terminal to the charged battery or the external power supply. 2. Press the [END/PWR] key for about 1.5 seconds until a red right appears on the upper side of the terminal. < Turning the Terminal Off > 1. Press the [END/PWR] key until the end message appears on the LCD, and then stop pressing the key. 2. If an antenna is stretched, push it in for safety.
3. If you are not sure of the phone entry number, select the Soft Key(BOOK) with the Right Mouse Button. 4. Place the cursor on the Phone Book, and press the Soft Key(SEL) with the Left Mouse Button. 5. Search the Phone Book Entry number or name requested in the Phone Book to attempt a call to the phone number stored in it. Rm LG BANNER Sep/09 MENU CION 12:30p m BOOK Input Entry #: ___ 1.Call History 2.Phone Book 3.Alarm 4.
character requested will be erased. Receiving Calls 1. Press any key except for the [END/PWR] key to receive a call. Press the END Key to end the incoming call 2. When the call completes, press the [END/PWR] key. Mute 1. Press the Soft Key(MENU) with the Left Mouse Button during the call. 3. Press the Soft Key(MENU) with the Left Mouse Button to clear the function. The popup menu will appear. Select the Unmute menu. (The message “Mute” will be disappeared on the screen.) 2.
Redialing Last Outgoing Number 1. Just press [SEND] key to redial the last outgoing number. Then, the call will be attempted. using the Call History 1. Press the Soft Key(BOOK) with the Right Mouse Button. 2. Place the cursor on the Call history menu on the screen, and press the Soft Key(SEL) with the Left Mouse Button. Rm 1.Call History LG CION Sep/09 Sun/PM 12:30 MENU 2.Phone Book 3.Alarm 4.Own Number BOOK SEL ¡ ã ¡ å BACK 3. Then, three menus will appear.
If you turn the ring volume down to the minimum, the message “-Ringer Off-“ will be indicated on the LCD and no ringing sound will be sent out. - Adjust the Ring Type on the Sound item on the Menu screen.
CHAPTER 3. MENU FEATURE Main Menu It is possible to verify or change various functions or setup the terminal status on the main menu. Rm LG CION Sep/09 Sun/PM 12:30 MENU BOOK General Guidelines to MENU Access and Settings 1. Sound 1. Press the Soft Key(MENU) on the left and the menu items will appear. 2. Use the upside and downside keys (é ê) to move to the menu items screen. 2. Display 3. Call info 4. indicated Features not SEL ¡ ã ¡ å on the BACK 3.
2. Ring Type ( F [MENU]-1-2 ) Set one of three Ring Types (Ring, Lamp, Ring+Vibrate and Vibrate) with the direction keys. Ring Type ¢ º Ring Lamp VIB+Ring Vibrate OK ¡ ã ¡ å BACK 3. Ringer Volume ( F [MENU]-1-3 ) Set of the ring volume in five levels (Most High - High - Medium – Ring Volume --------------- Low - Off ) with the direction keys. --------------OK ¡ ã ¡ å BACK 4. Key Beep (F [MENU]-1-4) Set the tone length in two levels (Normal, Long) with the direction Key Beep keys.
7. Alerts Sound ( F [MENU]-1-7 ) An alert signal is activated according to each situation by five 1. Fade 2. Minute 3. Service 4. Call Connect SEL ¡ ã ¡ å submenus under the Alert menus. BACK - Fade: It is activated if the call is disconnected in a busy line state. (On / Off) - Minute : This signal is activated when 1 minute elapses from the call connection. (On / Off) - Service : This signal notifies whether a call is available or not between the service and the no service areas.
3. Auto Hyphen (F [MENU]-2-3 ) It is possible to set the function to enter the Hyphen to the input number automatically to an “On” or “Off” state. . AUTO HYPHENATION Off On ¡ ã ¡ å OK BACK 4. Version ( F [MENU]-2-4 ) Version When you select this menu you can see the hardware and software version. H/W:0.5 S/W:C16PT01 OK BACK 5.
2. Home Calls (F [MENU]-3-2 ) - Total call time at the Home system (not roaming) from initial setup to the present. Home Calls Home Call zero 2 Calls 00:08:00 ZERO OK 0 Calls 00:00:00 OK BACK ZERO BACK 3. Roam Calls ( F [MENU]-3-3 ) Shows the call time at the roaming system from initial setup to the present Roam Call 2 Calls 00:08:00 OK ZERO BACK 4. All Calls ( F [MENU]-3-4 ) It shows the total call time to the present either at the Home system or the roaming system or both.
2. Auto Answer ( F [MENU]-4-2 ) Auto answer service is one of the most useful functions while Auto Answer Off After 1 ring After 3 rings driving a vehicle, and it enables automatic answering to the incoming call after the bell rings for designated times. (Off, 1 ring after, 3 ring after) ¡ ã ¡ å OK BACK 3. Auto Retry ( F [MENU]-4-3 ) If the called user is in a busy line state, this service automatically attempts a call to that number in a certain interval.
four characters, the process will not proceed to the following low level menu. And if the Lock Code is not correct, the process will return to the Main Menu. 1. Lock Mode ( F [MENU]-5-1 ) Set the terminal lock function to either “On Power Up”, “Never”, or “Always” with the direction key. 2. Restrict ( F [MENU]-5-2 ) This service enables restriction on the call service. Select either “Yes” or “No” with the direction key. The call service will be restricted only to the emergency phone numbers.
CHAPTER 4. Message(SMS) Message Service This service supports reception of the text message, alerting, origination of the text message, and the voice mailbox. It is possible to access the above functions with the text message key Call back service is also available with the call key ([OK] key) , if the calling number is indicated on the message received. It is possible to store up to 25 messages (received message : 20 , originated message : 5) and to receive up to 153(TeleSP) characters per message.
Hello this is Ki m from IBM. Plea se call me ASAP. I wiil be staying OK Hotel Clinton. at Erase Waiting... OPT BACK - - [Next]: It indicates that there is another message received. (If no more new message has been received, the old text list will be indicated.) [Erase]: It erases the message. [Call back]: It calls back to the calling number. 1.1.2 Old Text (*) 9/18 3:25pm Message from Smith Kim 0113456789 Hello this is Ki m from IBM. 1. Text 1/0 2.
3. Send message - Menu to originate SMS 3.1 New Message - Menu to originate new SMS Receiver Phone # Rm LG CYON Sep/09 [Fri] BANNER 3. Send Msg 4. Setting 123-456 12:30p BOOKm MENU ¢ ºCall 1. Text 0/0 2. Voice 0 ¡ ã ¡ å SEL BACK ¡ ã ¡ å OK Write MSG [80] Back# 1.New Message 567-890 2.Outbox 3.Inbox 4.Erase ¢ ¸ ¡ ã ¡ å OK BACK BACK ¡ ã ¡ å SEL BACK English ¡ ã ¡ å SEL ¢ º CLR - After input message, select OK and Send message 3.
3.3 Inbox Message - Menu to originate the message from the messages stored by the message service Receiver Phone # Rm LG CYON Sep/09 [Fri] BANNER Back# ¡ ã ¡ å ¡ ã ¡ å SEL BACK 1.New Message 567-890 - 123-456 12:30p BOOKm OK 3. Send Msg 4. Setting MENU ¢ ºCall 1. Text 0/0 2. Voice 0 BACK 2.Outbox 3.Inbox 4.
4. Setting - It is possible for the user to set the alarm to report arrival of a message. Alert: Select one of 2 alerts, 4 alerts, mute and vibrator services. After selecting Alert, select OK 1.Alert Rm LG CYON Sep/09 [Fri] BANNER 3. Send Msg 4. Setting 12:30p BOOKm MENU Rate Set Silent 2 Rings 4 Rings Vibrator OK 1. Text 0/0 2.
5. Erase All - This service enables erasing of all the messages stored by the message service. Erase Message Erase All Message? Selecting OK OK BACK Erasing Please Wait.