LGE CDMA Fixed Wireless Terminal LST-260 CDMA Fixed Wireless Terminal User Guide Model: LST-260 2
LGE CDMA Fixed Wireless Terminal LST-260 REVISED HISTORY DATE 2005.4.21 ISSUE ISSUE 0.1 CONTENTS OF CHANGES Preliminary REMARK FCC DOC Please read this manual before you use this product. This manual is based on the production version of LST-260 FWT. Software changes may have occurred after this printing. LGE reserves the right to make changes in technical and product specifications without prior notice.
LGE CDMA Fixed Wireless Terminal LST-260 Blank Page 4
LGE CDMA Fixed Wireless Terminal LST-260 Table of Contents 1. Before You Start ..................................................................................................... 7 1.1 Safety Information...................................................................................................................... 7 1.2 Optimal Phone Performance ..................................................................................................... 7 1.3 Care and Service ..............................
LGE CDMA Fixed Wireless Terminal LST-260 5.8 Restrict Call Mode Setting ....................................................................................................... 27 Set Restrict Call Level ............................................................................................................. 28 Storing the Permit Dial Number ............................................................................................... 28 Storing the Deny Dial Number (Restricted dial number) ............
LGE CDMA Fixed Wireless Terminal LST-260 1. Before You Start 1.1 Safety Information Warning To reduce the risk of fire or electric shock, do not expose this product to rain or moisture. Do not use this product near swimming pools or other bodies of water. IMPORTANT Before installing or operating this product, read this information. 1.2 Optimal Phone Performance z Do not operate your product when holding the antenna, or when someone is within four inches (ten centimeters) of the antenna.
LGE CDMA Fixed Wireless Terminal LST-260 z Avoid wetting the unit with any liquids. If the unit gets wet, turn the power off immediately and remove the backup battery and AC power supply. If the unit is inoperable, then return to the service agent for service. z Avoid shock or impact. z We recommend you to charge the backup battery before initial use. Backup battery may be discharged during delivery. z This device complies with part 15 of the FCC Rules.
LGE CDMA Fixed Wireless Terminal LST-260 Do not use or store it in dusty, dirty areas as its moving parts can be damaged. Do not store it in hot areas. High temperatures can shorten the life of electronic devices, damage batteries, and wrap or melt certain plastics. Do not store it in cold areas. When the phone warms up to its normal operating temperature, moisture can form inside the phone, which could damage the phone’s electronic circuit boards. Do not attempt to open it.
LGE CDMA Fixed Wireless Terminal LST-260 Do not plug many power cords in outlet. It may be a cause of fire or electric shock. Do not remodel the power cord or disassemble. If power cord or plug is impaired, do not use it. It may be a cause of fire or electric shock. Do not install in the ill-ventilated place. It may be a cause of fire or breakdown. Do not touch the plug with wet hands. When disconnect the power cord of any accessory, grasp and pull the plug, not the cord.
LGE CDMA Fixed Wireless Terminal LST-260 2. Introduction Congratulations on your purchase of the LG Fixed Wireless Terminal that has been designed to operate on the latest digital mobile communications technology, Code Division Multiple Access (CDMA). This CDMA digital technology has greatly enhanced voice clarity and can provide various advanced features. The terminal enables the normal operation and direct connection of standard telephone equipment into the cellular network.
LGE CDMA Fixed Wireless Terminal LST-260 2.1 Front, Side and Rear View of the Terminal .3..8… < Figure 1 > ITEM DESCRIPTION ① LEDs Indicate the status of the unit ② DC IN 12V AC/DC Power Adapter ○ 3 Batt.
LGE CDMA Fixed Wireless Terminal LST-260 65mm 65mm Mounting Template 2.1.1 Installation for Wall Mounting To mount terminal on the wall, please follow the procedure to install it correctly. 1. Determine suitable location to mount terminal with mounting template; 2. Mark the two openings and select round or pan-head type screw; 3. Drill out the holes with drill bit smaller in diameter than the screws 4. Secure two screws into the wall, leaving about 65mm gap between the screw heads. 5.
LGE CDMA Fixed Wireless Terminal LST-260 2.2 3 LEDs Indicators LED COLOR Operating Condition GREEN-solid POWER LED SIGNAL LED DC Power is applied RED-solid Battery Power is applied ORANGE -solid Low Battery GREEN-solid Good Signal ORANGE-solid Poor Signal RED-solid MODE LED No Service Area GREEN – blink (0.5sec On / 0.
LGE CDMA Fixed Wireless Terminal LST-260 z Please make sure that these components are present and check for evidence of shipping before you begin the unit installation. z If components are missing or damage is found, contact your authorized LG distributor immediately. STEP 2. Place the Terminal z Place the terminal on the stable flat secure surface area (desk, table, etc.). Avoid direct exposure to the sun lights and damp area.
LGE CDMA Fixed Wireless Terminal LST-260 1 [LST-260] [ Figure 2. Connection Diagram with External Equipment ] * Note : - G3 FAX can not connected to your LST-260 terminal. - Length between LST-260 and Telephone : over 1m. The adapter type(with power cord) may be different from country to country. ! Connection telephone jack to data port will cause malfunction of data service Notice Before using the terminal, please check battery switch is on. After switching on it, use the phone.
LGE CDMA Fixed Wireless Terminal LST-260 2.4 Installation Steps Please follow the below procedure to install the unit properly. 1. 2. Connect the Bend the Antenna to the antenna up TNC connector right. (Turn right). 3. 4. Connet your Connect the Phone Cord. Power supply DC supply. Terminal Connection Battery Connection z z z First, slow down the terminal slide switch and unscrew. To connect battery, disassemble terminal like above figure.
LGE CDMA Fixed Wireless Terminal LST-260 3. Basic Operation 3.1 Power On 1. The POWER LED indicates the presents status; 1) Using AC Adapter : Solid GREEN 2) Using internal battery : Solid RED 3) Using internal battery and battery is weak capacity: Solid ORANGE 2. When the terminal succeeded in getting the service, SIGNAL LED indicates the strength of the signal(Table 1). Lifting handset on telephone, dial tone is heard and you can enter a phone number.
LGE CDMA Fixed Wireless Terminal LST-260 flash more than about 1 second to end a call and place a new call without hanging up the handset. 3.5 Warning Tone after Remote Disconnect A warning tone may be heard in the telephone after a remote party hangs up from a call, allowing another call to be initiated after hook-flash. 3.6 Emergency Call When emergency call number is connected once, it will not be terminated unless the called party disconnects the call (Emergency Call Hold Service).
LGE CDMA Fixed Wireless Terminal LST-260 4. System Features 4.1 Hook flash When the terminal receives a hook-flash from the connected telephone device, it will automatically allow: 1. For producing dial tone again after a phone number has been dialed without connection. 2. The use of special cellular services which may be available in your cellular service area.
LGE CDMA Fixed Wireless Terminal LST-260 Voice mail – Use voice mail service in the same manner as you would on a regular telephone. If you have a new voice-mail message, the WLL-terminal transmits a special Voice-mail Notification Ring (4sec On / 1sec Off default) and Mode LED is blinking (0.5sec On / 0.5sec Off). Please contact your cellular service provider for more information on using Voice Mail or to change Voice-Mail Ring pattern.
LGE CDMA Fixed Wireless Terminal LST-260 5. Programming LST-260 provides various convenient and various features to user. This chapter describes how to program these features and to use them. The followings are main features can be used; Speed Dial Emergency Call Hot Line Call Wake-up Alarm Conversation Voice Level Outgoing Call Lock G3 Fax/Data Mode Restrict Call 1. 2. 3. 4. 5. Programming Instruction Lift Handset and press “#” key twice and you will hear the Menu Entering tone.
LGE CDMA Fixed Wireless Terminal LST-260 Erase All Speed Dials. 1. Press “#” + “#” + “1” continuously to enter speed dial programming mode. 2. Press “#” and “3” to erase all speed dials. 3. Press “*” to store Note 1. Speed dial feature is disabled after erase operation executed. Operation 1. Make a speed dial function enable. 2. Lift handset and dial tone will be heard. 3. Press speed dial number and wait for dial timeout.
LGE CDMA Fixed Wireless Terminal LST-260 5.3 Hot Line While the Hot line function is enabled, the programmed number will be automatically dialed when you pick up the handset and wait for the programmed hot line time (2~10sec) without any key press. Programming the Hot Line number 1. Press “#” + “#” + “3” continuously to enter Hot Line programming mode. 2. Press “#” and Hot Line Enable code “1”. 3. Press “#” and Hot Line phone number (Max. 32 digits). 4. Press “*” to save and enable this function.
LGE CDMA Fixed Wireless Terminal LST-260 Entering Alarm Time (24-hour Mode) 1. Press “#” + “#” + “4” continuously to enter alarm time programming mode. 2. Press “#” and alarm time code “2” for 24-hour mode. 3. Press “#” and alarm time (HHMM). (0000~2359) 4. Press “*” to save and enable Alarm Time. Disable Alarm Feature 1. Press “#” + “#” + “4” continuously to enter alarm time programming mode. 2. Press “#” and alarm disable code “2”. 3. Press “*” to save.
LGE CDMA Fixed Wireless Terminal LST-260 Changing Outgoing LOCK Code 1. Press “#” + “#” + “6” + continuously to enter Outgoing Call Lock programming mode 2. Press “#” and “LOCK code (4 digits)” 3. Press “#” and “3” to change LOCK code. 4. Press “#” and “new LOCK code (4 digits)”. 5. Press “#” and re-enter “new LOCK code (4 digits)”. 6. Press “*” to save.
LGE CDMA Fixed Wireless Terminal LST-260 Note 1. How to setup G3 FAX mode more easily 1. Press “#” + “#” + “7” continuously to enter G3 FAX/DATA programming mode. 2. Press Enable (“1”) or Disable (“2”) code. Enable means that Data call path is changed to G3 FAX. Disable means that Data call path is changed to RS-232C. (Default mode) Note 2. Sending or receiving some documents by G3 FAX is possible only in AC power mode.
LGE CDMA Fixed Wireless Terminal LST-260 Set Restrict Call Level 1. Press “#” + “#” + “8” + continuously to enter Restrict Call programming mode. 2. Press “#” and “LOCK code” (4 digits : set in Outgoing call lock). 3. Press “#” and restrict level (1~4) “1” – No restriction “2” – restriction “3” – Emergency only (All excepting emergency are restricted.) “4” – Clear restrict table 4. Press “*” to save Storing the Permit Dial Number 1.
LGE CDMA Fixed Wireless Terminal LST-260 6. Troubleshooting In the event you are unable to place or receive telephone calls, first check the appropriate power indication on the LED. In case of no power, check the wiring connections between the power outlet and the terminal. Check for the appropriate service indication on the LED. If an adequate signal is not present, try different locations for the better signal reception.
LGE CDMA Fixed Wireless Terminal LST-260 7. General Information 7.1 LST-260 z Main Unit Item Description Tx Frequency 824 ~ 849 MHz Rx Frequency 869 ~ 894 MHz Channel Bandwidth 1.25 MHz Frequency Stability ±300 Hz Tx Power Max. 0.
LGE CDMA Fixed Wireless Terminal LST-260 Appendix FCC RF Exposure Information WARNING! The antenna used for this transmitter must not exceed 3.0dBi and must be installed to provide a minimum separation distance of 20 cm from all persons. CAUTION Use only the supplied and approved antenna. Use of unauthorized antennas or modifications could impair call quality, damage the phone, void your warranty and/or result in violation of FCC regulations. Do not use the phone with a damaged antenna.
