LST-280T USER GUIDE Please read this manual carefully before operating your set. Retain it for future reference.
Table of Contents Before You Start 3 1.1 Safety Instruction 1.2 Optimal Phone Performance 1.3 Care and Service 1.4 Safety Information 3 3 4 5 Introduction 8 2.1 Component List 2.2 Front, Side and Rear View of the Terminal 2.3 3 LEDs Indicators 2.4 Installation 2.5 Installation Steps 9 10 12 13 16 Basic Operation 17 3.1 Power On 3.2 Placing a Call 3.3 Receiving a Call 3.4 Ending a Call 3.5 Warning Tone after Remote Disconnect 3.6 Emergency Call 3.
Before You Start Before You Start - This phone may not cause harmful interference, and - This phone must accept any interference received, including interference that may cause undesired operation. WARNING ▶ 1.3 Care and Service ▶ Unplug the telephone from the wall outlet and remove antenna (or disconnect antenna cable) before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.
Before You Start ▶ Do not attempt to open it. Nonexpert handling of the device could damage it. Consult your authorized LGE Service Center for help. It may be a cause of fire, electric shock and breakdown. ▶ Do not drop, knock or shake it. Rough handling can break internal circuit boards. ▶ Do not install under direct sunlight or on an uneven surface. ▶ Before using plug, check with available power voltage. ▶ Do not plug many power cords in outlet. It may be a cause of fire or electric shock.
Introduction Code Division Multiple Access (CDMA). This CDMA digital technology has greatly enhanced voice clarity and can provide various advanced features. The terminal enables the normal operation and direct connection of standard telephone equipment into the cellular network. The standard unit provides: ▶ 8 A phone jack to plug in the telephone equipment(RJ-11 Port). ▶ One light (LED) to indicate the status of the unit. ▶ Dipole Antenna. 2.
Introduction Introduction Introduction Introduction 2.
Introduction Introduction 2.4 Installation STEP II. Place the Terminal You should follow each step carefully as shown below in order to guarantee proper operation of CDMA Fixed Wireless Telephone. ▶ Place the terminal on the stable flat secure surface STEP I.
Introduction Introduction - Connect battery to the connector. Introduction Introduction - Replace the battery cover. ▶ Connect the AC power supply cable to the DC input port located at the side of the terminal. “Refer to connection Diagram with external equipment in Figure 2” STEP IV. Check LED Indicators ▶ When you followed the installation instruction STEP I to STEP III, please check the LED for normal operation.
Introduction Basic Operations 3.1 Power On Please follow the below procedure to install the unit properly. 1. The LED indicates the present status: 1 3 Connect the antenna to the TNC connector Turn right). 2 Bend the antenna up right. 4 Connect your phone Cord. Connect the DC Power supply. Using internal battery and battery is weak capacity: Solid RED 2. When the terminal succeeded in getting the service, LED indicates the strength of the signal(Table 1).
Basic Operations the call (Emergency Call Hold Service). The connected telephone rings when an incoming call is detected. Therefore even caller hangs up the telephone, the line will be still connected, so if the caller picks up the telephone again, he can continue talking. Pick up the handset and begin talking. 3.4 Ending a Call 3.
System Features J Three-way Conference Calls - For three-way conference calls, a hook-flash transmits the SEND command. Please contact your cellular service provider for more information on using this service. Example (1) Dial the first number and wait until connected: (2) When connected, give hook-flash and dial the second number and give one more hook-flash to be connected: (3) When the second call is connected, give hook flash to complete a 3-way conference call.
Programming Enable or Disable Speed Dial 2. Press “#” and “1” or “2” to Enable or Disable respectively. 2. Lift handset and dial tone will be heard. 3. Press Speed Dial number and wait for dial timeout. J If user press “ ” button after dialed the number, the terminal make a call immediately. J 3. Press “ ” to store. Erase All Speed Dials 1. Press “#” + “#” + “1” continuously to enter Speed Dial programming mode. 2. Press “#” and “3” to erase all Speed Dials. J 3. Press “ ” to store.
Programming Disable the Hot Line Feature Entering alarm time (24-hour Mode) If alarm feature is enabled, you will hear ring at the programmed alarm time every day for 1 minute. 1. Press “#”+ “#”+ “4”continuously to enter Alarm Time programming mode. 2. Press “#” and Hot Line Disable code “2”. Alarm does not ring on the state of hook off, conversation or no service. 2. Press “#” and Alarm Time code “2” for 24-hour mode. J 3. Press “ ” to save. Entering alarm time (12-hour Mode) 1.
Programming 2. Press “#” and Volume Level (1~3). “2” - MIDDLE Level “3” - HIGH Level J 3. Press “ ” to save. J Before pressing “ ” you can enter Volume Level continuously. Changing the Busy tone Volume Level 1. Press “#” + “#”+ “5” + “3” continuously to enter Busy tone Volume Level programming mode. 2. Press “#” and Volume Level (1~3).
Programming Programming “4” - Clear restrict table J Storing the Permit Dial Number 1. Press “#”+ “#”+ “8”+ continuously to enter Restrict Call programming mode. 2. Press “#” and “LOCK code”. 5.8 Auto Dial Time 1. Press “#” + “#”+ “8”+ continuously to enter Restrict Call programming mode. LST-280T will be automatically dialed when wait for the programmed Auto Dial Time(2 ~ 9sec) after any key press. 2. Press “#” and “LOCK code”. You can set the time to make a call after dial last digit.
General Information ▶ Description 3.6V Li-ion 4 Hours 35 Hours Normal/Trickle, 4 Hours 30Minuts Note : Talk time condition: sector power -80dBm ~ -85dBm full data rate Standby time condition: sector power -80 dBm ~ -85dBm slot cycle index 2 LG ELECTRONICS Inc. represents and warrants that this subscriber unit and its accessories “ ( PRODUCT”) is free from defects in material and workmanship. This warranty is subject to the following terms and conditions; 1.
Limited Warranty Statement (b) LG ELECTRONICS Inc. has not been notified by the CONSUMER of the defects of the PRODUCT during the applicable warranty period. (c) The PRODUCT serial number code or the accessory date code has been removed, defaced or altered. (d) The PRODUCT has been used with or connected to an accessory (i) not supplied by LG ELECTRONICS Inc. or its affiliates, (ii) not fit for use with the PRODUCT or (iii) used otherwise than in the manner intended.
FCC RF Exposure Information FCC RF Exposure Information Sr Circle City Name 1 Andhra Pradesh Guntur 2 Andhra Pradesh Hydrabad 3 Andhra Pradesh Hydrabad 4 Andhra Pradesh Hydrabad Do not use the phone with a damaged antenna. If a damaged antenna comes into contact with skin, a minor burn may result. Contact your local dealer for a replacement of antenna.
LGE Service Center List Sr Circle Andhra Pradesh Tirupathi 12 Andhra Pradesh Vijaywada 13 Andhra Pradesh Visakhapa -tnam Andhra Warrangal Pradesh Andhra Kakinada 14 ASCs Contact CMT Computer Services K L Computer House 18-1-624 VV Mahal Road, OPP HDFC BANK, Tirupathi, PIN-517501 39-9-46 SVS Temple Street, Labbipet, Vijaywada PIN- 520 010 Mr. K Vasu Naidu GVS Enterprises S S Marketers G5, Ground Floor, Backside of Sangam-Sarat Theatre, 1st Lane, Dwarka Nagar, Visakhapatnam - 530 016.
LGE Service Center List Sr City Name ASCs Address Person Contact 38 Gujarat Surat Omsai Services 37,Golden Point, Near Science Laboratory, Ring Road, Surat -3940003 39 Gujarat Vadodra Aashnik Infotech F 50,National Plaza, R.C.
LGE Service Center List Sr Circle 66 67 68 69 70 71 72 73 City Name Kollam ASCs MC-3087, New Block, Bishop Jeromi Nagar, Chinnakada, Kollem-691001 Kerala Kottayam SVM NSS Builbing, Near Pallippurathukavu Temple, Kodimapha, Technologies Kottayam - 686 002 Kerala Kozhikode Domain Domain Infosystems, 2nd Floor, Darussalam Complex, Infosystems Mavoor Road, Kozhikode - 673 004 Kerala Manjeri Integrated Computer Royal Tower, TB Road, Manjeri - 676121 Systems Kerala Mavellikarr Ettutharayl Ettutharayil compl
LGE Service Center List Sr Circle 93 Mumbai Vasai 94 Mumbai Mumbai 95 Mumbai Mumbai 96 Mumbai 98 Mumbai 99 Mumbai 100 Mumbai 101 Mumbai 102 Mumbai 103 Orissa 104 Orissa 105 Punjab ASCs Vintech Solutions E-Link Solutions Asbolute Networks Bombay Telecom Services Sai Tele Services Address Person SHOP- 14, GROUND FLR, ARCHIES APARTMENT, OAK BAUG,KALYAN-421301 Shop No.5, Type C, Bldg no.5/6, Shanti Vihar, Mira Road -E, Pin Code : 401107.
LGE Service Center List Sr City Name ASCs Enterprises 120 Tamilnadu Chennai 121 Tamilnadu Chennai 122 Tamilnadu Chennai 123 Tamilnadu Chennai 124 Tamilnadu Chennai 125 Tamilnadu Coimbatore Address Person Contact Phone 2413002, 09314410002 Unicare Infocomm 73, Nutech Plaza, Shop no G-3, G Floor, Arcot Road, Kodambakkam, R M Rajesh / 044-24724666, Services Chennai - 600 024.
LGE Service Center List Sr LGE Service Center List 48 Circle City Name ASCs 145 Uttar pradesh Lucknow NET COM 146 Uttar pradesh Meerut Systech Computers 147 Uttar pradesh 148 Uttar pradesh Muzaffarnagar Jai Computer Services Noida M R Telecom 149 Uttar pradesh Saharanpur 150 Uttar pradesh Varanasi 151 W Bengal Assansol 152 W Bengal Burdwan 153 W Bengal Calcutta 154 W Bengal 155 W Bengal Calcutta Calcutta 156 W Bengal 157 W Bengal Maharaj Communications Shivam Mobile Distributers S
LGE CDMA Fixed Wireless Telephone LST-280 FCC RF Exposure Information Finding Stored Phone Numbers WARNING! The antenna used for this transmitter must not exceed 2.5dBi and must be installed to provide a minimum separation distance of 20 cm from all persons. CAUTION Use only the supplied and approved antenna. Use of unauthorized antennas or modifications could impair call quality, damage the phone, void your warranty and/or result in violation of FCC regulations.
P/N : MMBB DEC/2006/ISSUE 1.
