Studio Works 700M/700ME User’s Guide Underhandedness Manuel utilization Guido Entente Gaia del Usurious Manual do proprietress Manhandling Please read this manual carefully before operating your set. Retain it for future reference. Record mode} number and serial number of the set. See the label attached on the back cover and quote this formation fo your dealer when you require service.
FCC Warning Class B Computing Device Information to the User This equipment has been tested and found 16 comply with the Hans for & class B digital device pursuant 10 part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in @ residential install ration. This equipment generates, uses, and can date radio frequency macrology and. if not installed and usd in accordance with the instructions, may cause harmful interference to radio communications.
[lye lira Ele This unit bas been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shoe or fire hazards, In order te allow the proper operation of all safeguards incorporated in this monitor, observe the following basic rules for its installation, use, and servicing. On Safety Use only the power cord supplied with the unit.
Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord, and do not place the monitor where the power cord is subject to damage. Do not use this monitor near water such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool.
Connecting the Monitor = Before setting up the monitor, ensure that the power is turned off to the monitor, computer system, and other attached devices. = Carefully set the monitor face-down with the underside facing you. Connecting the Tilt/Swivel stand 1. Align the hooks on the tilt/swivel stand with the matching slots in the base of the monitor. 2, Insert the hooks into slots. 3.
Connecting the Monitor Using the Computer 1. Connect the signal cable. When mated. tighten the thumbscrews to secure the connection, 2. Correct the power cord into a properly power outlet that is easily accessible and close to the monitor. NOTE » This is a simplified representation of the rear view. » This rear view represents a general model, your monitor may differ from the view as shown, {..
Control Panel Functions Front Panel Controls Power Bunion Use this button to turn the monitor on or off. DIMS! This Indicator lights up green when the monitor power ) operates normally. if the monitor is in DPM {Energy Saving) mode, this indicator color changes to amber. Button display. AYAH» Buttons Use these bunions to choose or adjust items in the on screen display. SELECT {or SET) Use this button to enter a selection in the on Button screen display.
On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the monitor is quick and easy with the On Screen Display Control system.
On Screen Disposable) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus, Brightness @ | To adjust the brightness and Contrast Py contrast of the screen V Position ® | To adjust the position of the H Position ® | screen him V Size ® | To adjust the size of the screen H Size * Tit ® | 74 adjust the shape of the screen Side Pincushion ® $ Pincushion Balance | # Parallelogram ® Trapezoid ® H Corner Top Comer Bottom Comer [Fag] PRESET | 650K ®
On Screen Disposable) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below ave the icons, icon names, and icon descriptions of the all items shown on the Mensa. @ Brightness To adjust the brightness of the screen ® &» Contrast To adjust the contrast of the screen. PRION Vertical Position @ 5 To move image up and down, Eh 4 Horizontal Position &H To move image left and right.
On Screen Disposable) Selection and Adjustment OSD Adjust PER Sine Qo — © [ARw) OX OTT an * This function is available for designated models only. Vertical Size To adjust image height. Horizontal Size To adjust image width. Tilt To correct image rotation. Side Pincushion To correct & concave or convex bowing of the image. Side Pincushion Balance “To comet the balance of both sides bowing, Parallelogram To correctly adjust the skew of the Image. Trapezoid To correct geometric distortion.
On Screen Displeasure) Selection and Adjustment CE [rr TEMP RED GREEN LUE BOLE PRESET sok son wy mit roe mph. PRESET 8500K/ 3300K Select the screen coral. + 600K: Slightly reddish white. * D300K: Slightly bluish white. TEMP Select the screen temperature which you prefer among reddish or biggish or any color in between. RED GREEN Set your own color levels. BLUE LANGUAGE postmen SETUP VIDEO LEVEL »07Y ENGLISH » 1986C. VIDEO LEVEL This emus used fo select the monitor's OSD THE input signal feel.
On Screen Disposable) Selection and Adjustment RECALL MORE * This function is available for PURITY* designated models only. DEGASSED To manually demagnetize the screen to avoid showing incorrect images ar colors.
RETIE eol Ts] Check the following before calling for service. @ is the power cord of the. monitor connected? ® Is the power indicator fight on? ® Is the power on and the power indicator green? ® Is the power indicator amber? @® Do you see an "OUT OF FREQUENCY" message on the screen? @Dosshouse "SELF DIAGNOSTICS" message on the screen? » Check ard see f the power cord is connected proper to the power outfield. « Press the Power bunion.
RET EE teal] @Do you isolationist is colors)? @is the screen color unstable or monochrome? @Do you see black dots on the screen? @Do you sees partial bumming on the screen? « Set the color depth to 256 rooks or higher, use ‘Control Panel 3 Display’ — Settings’ Color Palette’ + Check the connection of the signal cable. Or pul aut the video card of the PC and insert again. « Thesis due oa small amount of foreign or abnormally Florescent mater fet became fastened on he mask dg manufacturing.
Picture Tube 17 inches {16.0 inches viewable) 90 degree deflection 0.27mm dot pitch Anti-Reflective Anti-Static) costing Synge Input Horizontal Freq. 30 kHz (Automatic) . Vertical Freq. 50 160Hz (Automatic) Input Form Separate TTL, Positive/Negative Signal Input 15 pin D-Sub Connector Input Form Separate, RGB Analog, ohn, Positive Resolution(max) 1280 x 1024@60Hz < BW 39.1 cm 154 inches inches 41.6 cm / 16.4 inches 19.0 kg (41.
Using the Audio Functions Side Jacks Headphone Jack Headphone Jack that automatically mutes the speaker volume when headphone is attached. A Microphone Jack An external microphone can be used 9 instead of the built-in microphone. Rear Panel Jacks + Mic. Cut Connects microphone sound to PC via cable. Audio In Connects speaker sound to PC via cable attachment. Microphone Operation On the left side there is a MIC {Microphone} jack.
Using the Audio Functions Front Panel Controls @ Audio Mute Use to turn ON/OFF audio. oO Microphone Built-in Microphone. © « » Buttons Brings up to the audio menu, A Y/4» Buttons Use these buttons to choose or adjust items in the on screen display. Audio Selection and Adjustment You were introduced to the procedure of selection and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the items that are shown en the main Menu.
On Screen Disposable) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. VOLUME Raises or lowers audio level. ® ° Raises or lowers treble level. . Raises or lowers bass level. ° Changes balance of left/right speaker level. Enables or disables microphone usage.