Model number : Serial number : P/NO : 3828VA0338G(373-026H) LCD AV MONITOR Please read this manual carefully before operating your set. Retain it for future reference. Record model number and serial number of the set. See the label attached on the back of the set and quote this information to your dealer when you require service.
Multimedia Display This LCD monitor can be connected to a PC in place of the PC Monitor. The LCD Display panel The panel is composed of 2.9 million individual cells and a few defective cells are likely to appear as coloured dots on the screen as a result of the manufacturing process. This tolerance of upto six defective cells has been adopted by all panel manufacturers and therefore would not be considered as reason for exchange or refund.
Table of Contents First step Safety instructions ....................................................4 Monitor Overview Front Panel Controls ..............................................12 Connection Panel Overview ...................................13 Remote Control Key Functions ..............................14 Accesories/Optinal extra.........................................16 Using the remote control ........................................17 Equipment Connections and Setup VCR Setup...................
Safety Instructions WARNING Indoor Installation Do not place the Monitor in direct sunlight or near heat sources such as radiators, fires and stove etc. NOTES Do not place inflammable materials beside the monitor - This may cause a fire hazard ! - This may cause a fire hazard ! NOTES Indoor Installation When unpacking or moving the Monitor two people will be necessary to lift it safely. Do not place the monitor where it might be exposed to dust.
* Safety instructions have two kinds of information as illustrated below. NOTES ENGLISH WARNING The violation of this instruction may cause serious injuries and even death. The violation of this instruction may cause light injuries or damage of the product. Take care of danger that may happen under specific condition. NOTES Disconnect from the mains and remove all connections before moving. Do not place the monitor close to sources of steam or oil such as a humidifier.
Safety Instructions WARNING Outdoor Installation Do not use the Monitor in a damp place such as a bathroom where it is likely to get wet. - This may cause a fire or an electric shock hazard ! WARNING Outdoor Installation In case of using a receiver (VCR, In case of using a receiver Digital Set Top Box), do not place an (VCR, Digital Set Top Box), antenna in the vicinity of power lines. contact your service center to construct an antenna because - This may cause an electric shock. it needs skilled man.
ENGLISH WARNING In case of using a receiver (VCR, Digital Set Top Box), Bend antenna cable between inside and outside building to prevent rain from flowing in. - This may cause water damaged inside the Monitor and could give an electric shock. NOTES In case of using a receiver (VCR, Digital Set Top Box), there should be enough distance between an outside antenna and power lines to keep the former from touching the latter even when the antenna falls. - This may cause an electric shock.
Safety Instructions NOTES Power Hold the plug firmly when unplugging. If you pull the cord the cord may be damaged. Prevent dust collecting on the power plug pins or outlet. - This may cause a fire hazard ! - This may cause a fire hazard ! WARNING Do not place anything containing liquid on top of the monitor such as flowerpot, cup, cosmetics or candle.
ENGLISH NOTES Do not plug when the power cord or the plug is damaged or the connecting part of the power outlet is loose. Ensure the power cord does not come into contact with sharp or hot objects such as a heater. - This may cause a fire or an electric shock hazard ! - This may cause a fire or an electric shock hazard ! NOTES In case of impact shock or damage to the monitor switch it off and unplug it from the outlet and contact your service center.
Safety Instructions WARNING In the event that an image does not appear on the screen please switch it off and unplug it from the mains suuply and contact your Service Centre. Using - This may cause a fire or an electric shock hazard ! WARNING Do not use water while cleaning the Monitor Cleaning - This may cause damaged the Monitor or an electric shock hazard.
ENGLISH WARNING NOTES Do not watch the monitor while driving or walking. Do not place heavy objects on the Monitor. - This may cause an accident. - This may cause serious injury to a child or adult. NOTES Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Contact the service center once a year to clean the internal part of the monitor. - - Accumulated dust can cause mechanical failure.
Front Panel Controls POWER ON OFF POWER ON OFF MENU VOL MENU Main power button INPUT SELECT INPUT SELECT /I /I Sub power button MENU button D,E 12 VOL INPUT SELECT button VOLUME (F,G) buttons buttons Remote control sensor Power standby indicator Illuminates orange in standby mode, Illuminates green when the Monitor is turned on
ENGLISH Connection Panel Overview ( ) ( ) R ( ) EXTERNAL SPEAKER(6 Ω ) ( ) L DC OUTPUT R AUDIO L MONO (DC 12V) AV INPUT Y VIDEO PB PR S-VIDEO AC INPUT R COMPONENT (DVD/DTV INPUT) AUDIO L RGB 2 INPUT (DIGITAL RGB INPUT) RGB 1 INPUT (PC/DTV INPUT) RS 232C INPUT (CONTROL/SERVICE) AC INPUT jack Audio Input sound (R)(L)jacks RGB-1 (PC/DTV INPUT) RGB-2 (DIGITAL RGB INPUT) jack / A/V Input / COMPONENT RS-232C jacks (DVD/DTV) INPUT jacks / - Input RGB2(Digital RGB) when input S-vide
Remote Control Key Functions - When using the remote control aim it at the remote control sensor on the Monitor. POWER button SLEEP button (Refer to p. 31) POWER SLEEP INPUT SELECT APC DASP ARC PIP ARC PIP TWIN PICTURE SWAP SUB INPUT APC button ARC button PIP button SWAP button MENU button MENU MUTE ENTER button ENTER VOL 1 2 3 4 5 6 7 8 9 VOL VOL buttons 0 PIP buttons WIN.SIZE WIN.
ENGLISH input select button on the remote control Each press of this button changes the mode as shown below. RGB1 RGB2 COMPONENT INPUT SELECT button DASP button (Refer to p. 34) S-VIDEO VIDEO PIP ARC select button TWIN PICTURE button (Refer to p. 42~46) SUB INPUT button MUTE button switches the sound on or off.
Accesories/Optional extras Accesories POWER INPUT SELECT SLEEP DASP APC PIP ARC ARC TWIN PICTURE PIP SUB INPUT SWAP MENU MUTE ENTER VOL 1 2 3 4 5 6 7 8 9 VOL 1.5V 1.5V 0 WIN.SIZE WIN.
ENGLISH Using the remote control Installing batteries • Open the battery compartment cover on the back of the remote control and insert the batteries with correct polarity, match “+” with “+”, and match “-” with “-”. • Install two 1.5V “AAA” alkaline batteries. Don’t mix used batteries with new batteries. Notes for using the remote control Make sure these are no objects between the remote control and its sensor. Don’t place the remote control near a heater or damp place.
VCR Setup - As shown below, when connecting the Monitor to a VCR, match the colors of AV input jacks on the Monitor with the output jacks on the VCR: Video = yellow, Audio (Left) = white, Audio (Right) = red. - If you have a mono VCR, connect the audio cable from the VCR to the AUDIO (L/MONO) input of the Plasma Monitor. - If you connect an S-VIDEO VCR to the S-VIDEO input, the picture quality is improved, compared to connecting a regular VCR to the Video input.
ENGLISH DC OUTPUT (DC 12V) R AUDIO L MONO Y VIDEO PB PR AC INPUT S-VIDEO AV INPUT R COMPONENT (DVD/DTV INPUT) AUDIO L RGB 2 INPUT (DIGITAL RGB INPUT) RGB 1 INPUT (PC/DTV INPUT) RS 232C INPUT (CONTROL/SERVICE) Back panel of the Monitor To watch VCR INPUT SELECT 1 Press INPUT SELECT button on the remote control and select VIDEO. (When connecting with S-Video, select the S-VIDEO.) 2 Insert a video tape into the VCR and press the PLAY button on the VCR. See VCR owner’s manual.
Cable TV Setup - After subscribing to a cable TV service from a local provider and installing a converter, you can watch cable TV programming. This monitor cannot display TV programming without a TV tuner or cable TV converter box.
ENGLISH External AV Source Setup - As shown below, when connecting the Monitor to an external source, match the colors of AV input jacks on the Monitor with the output jacks on the audio/video equipment: Video = yellow, Audio (Left) = white, Audio (Right) = red.
DVD Setup How to connect a DVD (digital video disk player) • Connect DVD video inputs to Y, PB, PR of COMPONENT (DVD/DTV INPUT) and audio inputs to Audio jacks of AV INPUT. • Component Input is available to 480i, 480p, 720p, 1080i mode.
ENGLISH DTV Setup - To watch digitally broadcast programs, purchase/connect a digital SET-TOP BOX. How to connect • You can use either the Monitor’s COMPONENT (DVD/DTV INPUT) inputs or the single RGB1(PC/DTV INPUT) for video connections, depending on your Set Top Box connectors. Then, make the corresponding Audio connections. • DTV Input is available to 480p, 720p, 1080i mode.
Connecting to a wireless trasmitter (option) • Only adjust this function in some models. • When connecting the wireless transmitter with external equipments, match the colors of connecting ports (Video - yellow, Audio(L) - white, Audio(R) -red). • If you have a mono VCR, connect the audio cable from the VCR to the AV input of the wireless AV transmitter. • See the wireless trasmitter-receiver operating guide for installation and connection etc.
ENGLISH Connecting to a wireless receiver (option) • Only adjust this function in some models. • When connecting the wireless receiver with external equipments, match the colors of connecting ports (Video - yellow, Audio(L) - white, Audio(R) -red).
PC Setup - You can easily connect the Plasma Display to your PC for outstanding image and sound. Setup Instructions to Connect a PC to your Monitor • Connect the audio cable from the PC to the Audio ports of the Monitor. • If your PC computer is equipped with a sound card, adjust the sound output on the PC. • Select the display resolution of the PC to 1024X768 for the best picture. This monitor’s resolution is 1280X768.
Monitor Image Display Specifications (RGB1) 640x350 720x400 640x480 800x600 1024x768 1152x864 1280x960 1280x1024 832x624 ENGLISH Resolution Horizontal Vertical Frequency (KHz) Frequency (Hz) 31.468 70.09 37.861 85.08 31.469 70.08 37.927 85.03 31.469 59.94 37.861 72.80 37.500 75.00 43.269 85.00 53.011 100.04 64.062 120.00 35.156 56.25 37.879 60.31 72.18 48.077 46.875 75.00 53.674 85.06 56.000 90.00 64.016 100.00 48.363 60.00 56.476 70.06 60.023 75.02 68.677 84.99 54.348 60.05 67.500 75.00 77.487 85.
Monitor Image Display Specifications (RGB2) Resolution 640x350 720x400 640x480 800x600 1024x768 1152x864 1280x960 1280x1024 832x624 28 Horizontal Vertical Frequency (KHz) Frequency (Hz) 31.468 70.09 37.861 85.08 31.469 70.08 37.927 85.03 31.469 59.94 37.861 72.80 37.500 75.00 43.269 85.00 35.156 56.25 37.879 60.31 72.18 48.077 75.00 46.875 53.674 85.06 48.363 60.00 56.476 70.06 60.023 75.02 68.677 84.99 54.348 60.05 67.500 75.00 85.05 77.487 60.000 60.00 75.000 75.00 63.981 60.02 49.725 74.
ENGLISH Turning on the Monitor - When using the remote control, aim it at the sensor on the Monitor. Turning on the Monitor just after installation 1 Connect power cord correctly. 2 Press the main ON OFF button on the Monitor. At this moment, the Monitor is switched to standby mode. Press the or INPUT SELECT button on the Monitor or press the POWER or INPUT SELECT button on the remote control and then the Monitor will be turned on.
Checking features - Use the remote control to make adjustments. - Select VIDEO input source. 1 Press the MENU button. 2 Press the UP/DOWN button. • Each press will cycle through the menus shown below. SOUND PICTURE APC CONTRAST BRIGHTNESS COLOR SHARPNESS TINT SCREEN D MOVE E menu DASP TREBLE BASS BALANCE EXIT D MOVE menu EXIT E
ENGLISH Setting Sleep Timer Sleep Timer turns the Monitor off after a preset time SLEEP Press the SLEEP button to set sleep time. Each time you press SLEEP button, the next preset setting time is changed as follows: OFF 10 20 30 120 90 60 240 180 SLEEP: 10 • To release sleep time setting, press the SLEEP button repeatedly to select OFF. Tips • To check remaining sleep time after setting, press the SLEEP or ENTER button just once.
Auto picture control Use APC to set the Monitor for the best picture appearance APC (Auto Picture Control) APC 1 Press the APC button. 2 Press the APC or UP/DOWN buttons to select your desired picture condition. APC CLEAR SOFT USER USER D ADJUST A EXIT E • Each press of APC button or UP/DOWN buttons changes the screen display as shown below. CLEAR SOFT USER • You can also select CLEAR, SOFT or USER in the PICTURE menu.
ENGLISH Adjusting picture appearance READY Press the MENU button and then press the UP/DOWN button to select PICTURE menu. Press the VOL ( G ) button. MENU 1 VOL Press the UP/DOWN button to select CONTRAST and then press the VOL ( G ) button. VOL 2 Use the VOL buttons to make appropriate adjustments and then press the ENTER button. PICTURE APC CONTRAST BRIGHTNESS COLOR SHARPNESS TINT SCREEN G 100 D MOVE F PREV. E CONTRAST 80 FG ADJUST D MOVE A PREV.
Auto Sound Control DASP (Digital Auto Sound Processing) • This function lets you enjoy the best sound without any manual adjustment because the Monitor automatically selects the appropriate audio tone levels based on the program content. DASP 1 Press the DASP button. 2 Press the DASP or UP/DOWN button to select a sound setup. DASP NORMAL NORMAL CINEMA MUSIC SPORTS USER D ADJUST A EXIT E • Each press of DASP or UP/DOWN buttons changes the screen display as shown below.
ENGLISH Adjusting Sound Manual Settings READY Press the MENU button and then press the UP/DOWN button to select SOUND menu. Press the VOL ( G ) button. MENU 1 VOL Press the UP/DOWN button to select TREBLE and then press the VOL ( G ) button. SOUND DASP TREBLE BASS BALANCE G 100 VOL D MOVE F PREV. E 2 Use the VOL buttons to make appropriate adjustments and then press the ENTER button. • Press the UP/DOWN buttons to select other items.
Selecting language for the menus READY Press the MENU button and then press the UP/DOWN button to select SPECIAL menu. Press the VOL ( G ) button. MENU 1 VOL Press the UP/DOWN button to select LANGUAGE and then press the VOL ( G ) button. VOL SPECIAL D E 2 ˙–„ LANGUAGE ¢” LANGUAGE COLOR TEMP. R-ADJUST G-ADJUST B-ADJUST SCREEN SAVER SET ID MOVE F ENGLISH PREV. Press the UP/DOWN button to select the desired language. SPECIAL ˙–„ ENGLISH ENGLISH LANGUAGE COLOR TEMP.
ENGLISH Adjusting color temperature READY Press the MENU button and then press the UP/DOWN button to select SPECIAL menu. Press the VOL ( G ) button. MENU 1 VOL Press the UP/DOWN button to select COLOR TEMP. and then press the VOL ( G ) button. VOL 2 Press the UP/DOWN button to select your desired color temperature and then press the ENTER button. ENTER SPECIAL LANGUAGE COLOR COLOR TEMP. TEMP. G R-ADJUST G-ADJUST B-ADJUST SCREEN SAVER SET ID NORMAL COOL WARM USER D MOVE F PREV.
Using the Screen Saver function - Prolonged display of a still image may cause a permanent image to be ‘burnt’ on the screen - If you select Screen Saver "ON", to prevent the permanent image, the picture moves a little by the sequence of "Right-Bottom-Left-Up" every 10 minutes.
ENGLISH Setting picture format - Wide and normal size are possible in RGB1(PC) and RGB2 mode, and Wide, normal and zoom size are possible in RGB1(DTV) mode. ARC Press the ARC button to select a desired picture format. • Each time you press ARC buttons, you can select WIDE, NORMAL or ZOOM alternatively. WIDE NORMAL ZOOM • You can also select WIDE, NORMAL or ZOOM in the PICTURE menu.
Using the Zoom in/out function READY Press the MENU button and then press the UP/DOWN button to select PICTURE ADJ. menu. Press the VOL ( G ) button. MENU 1 VOL Press the UP/DOWN button to select ZOOM IN/OUT and then press the VOL ( G ) button. PICTURE ADJ. VOL AUTO. CONFIG. ARC(MAIN). ZOOM ZOOMIN/OUT. IN/OUT G POSITION CLOCK ADJUST PHASE ADJUST RESET ADJUST G 0 D MOVE F PREV E 2 Press the VOL buttons to adjust desired zoom in or out. PICTURE ADJ. VOL VOL AUTO. CONFIG. ARC(MAIN).
ENGLISH Moving the picture - Adjust the screen with ‘ZOOM IN/OUT’ function to use the ‘POSITION’ function. READY Press the MENU button and then press the UP/DOWN button to select PICTURE ADJ. menu. Press the VOL ( G ) button. MENU 1 VOL Press the UP/DOWN button to select POSITION and then press the VOL ( G ) button. VOL PICTURE ADJ. AUTO. CONFIG. ARC(MAIN). ZOOM IN/OUT POSITION. G POSITION CLOCK ADJUST PHASE ADJUST RESET ADJUST D F G E D MOVE F PREV.
Picture in picture (PIP) function - PIP/TWIN PICTURE will let you view two seperate inputs on your monitor screen at the same time. - Color of main picture may be different from PIP’s in PIP/TWIN PICTURE. - When the main picture is RGB1/DTV(more than 480p), the sub picture is Input/S- video/DVD(480i) and when the main picture is Input / S- video / DVD(480i), the sub picture is RGB1 / DTV(more than 480p) / RGB2. How to use the PIP Press the PIP button.
ENGLISH Moving the sub picture Press the WIN. POSITION button in PIP. • Press the VOL(F, G) button and UP/DOWN button to adjust the position. WIN.POSITION WINDOW POS. D F G ADJ. A EXIT E Change the main picture and the sub picture Press the PIP SWAP button in PIP. SWAP RGB1 VIDEO VIDEO RGB1 How to connect external control equipment Press the PIP INPUT button in PIP. RGB1 VIDEO SUB INPUT Tips • You can select WINDOW SIZE, WINDOW POSITION, PIP INPUT in the TWIN/PIP menu.
Zoom in/out main picture How to connect external control equipment Press the ZOOM+ button in PIP mode. ZOOM+ ZOOM 25 D F G POS.ADJ. E EXIT A • Enlarge the picture with ZOOM+ button. ‘ZOOM’ is possible to 50. • Press the ZOOM- button to reduce the zoom effect. Moving the enlarged picture Press the VOL (F, G) button or UP/DOWN button to adjust the position of main picture. • When the ‘ZOOM’ is ‘0’ moving position. ZOOM 25 D F G POS.ADJ.
ENGLISH Twin picture function How to use twin picture TWIN PICTURE Press the TWIN PICTURE button to select desired twin picture. • Each time you press TWIN PICTURE buttons, you can select TWIN1, TWIN2 or TWIN OFF alternatively. TWIN1 TWIN2 TWIN 1 TWIN OFF TWIN 2 TWIN OFF Input select of the sub picture SUB INPUT Press the SUB INPUT button to select the input select of sub menu.
Twin picture function - PIP/TWIN PICTURE let you view different inputs on your monitor screen at the same time. - Color of main picture may be different from PIP’s in PIP/TWIN PICTURE. - When the main picture is RGB1/DTV(more than 480p), the sub picture is Input/S- video/DVD(480i) and when the main picture is Input / S- video / DVD(480i), the sub picture is RGB1 / DTV(more than 480p) / RGB2. Changing the picture of main and sub picture Press the SWAP button in twin picture mode.
ENGLISH Using the screen options - This function works only in the video mode and S-video mode. READY Press the MENU button and then press the UP/DOWN button to select PICTURE menu. Press the VOL ( G ) button. MENU 1 VOL Use the UP/DOWN button to select SCREEN and then press the VOL ( G ) button. VOL PICTURE APC CONTRAST BRIGHTNESS COLOR SHARPNESS TINT SCREEN SCREEN G VCR TV D MOVE F PREV E 2 Use the UP/DOWN buttons to select TV or VCR.
PC Mode Feature Check - Use the remote control to make adjustments. - Select RGB 1 input source. 1 Press the MENU button. 2 Press the UP/DOWN button. • Each press will cycle through the menus shown below. SOUND PICTURE APC CONTRAST BRIGHTNESS COLOR SHARPNESS TINT SCREEN D MOVE menu E DASP TREBLE BASS BALANCE EXIT D MOVE menu EXIT E
ENGLISH PC Mode Adjustment - This function works only in the RGB1 mode. READY Press the MENU button and then press the UP/DOWN button to select PICTURE ADJ. menu. Press the VOL ( G ) button. MENU 1 VOL Use the UP/DOWN button to select AUTO CONFIG. and then press the VOL ( G ) button. VOL PICTURE ADJ. AUTO AUTO.CONFIG. CONFIG. G ARC(MAIN). ZOOM IN/OUT POSITION CLOCK ADJUST PHASE ADJUST RESET TO SET D MOVE F PREV E 2 When AUTO CONFIG. has finished, ‘OK’ will be shown on screen.
PC Mode Adjustment - Horizontal/Vertical position and CLOCK/PHASE adjustment work in RGB1(PC mode) and Horizontal/Vertical position only work in RGB(DTV mode-480p,720p,1080i). READY Press the MENU button and then press the UP/DOWN button to select PICTURE ADJ. menu. Press the VOL ( G ) button. MENU VOL 1 Use the UP/DOWN button to select CLOCK ADJUST and then press the VOL ( G ) button. VOL PICTURE ADJ. AUTO. CONFIG. ARC(MAIN).
ENGLISH External Control Device Setup - Connect the RS-232C input jack to a PC and control the Monitor’s functions (such as ON/OFF, INPUT SELECT, MUTE) externally. How to connect external control equipment • Connect the RS-232C (serial connector) input jack with the rear of moniter’s RS-232C input jack. • RS-232C connection cables are not supplied with the Monitor.
External Control Device Setup SET ID • Use this function to specify a monitor ID number. READY Press the MENU button and then press the UP/DOWN button to select SPECIAL menu. Press the VOL ( G ) button. MENU 1 VOL Use the UP/DOWN buttons to select SET ID and then press the VOL ( G ) button. VOL SPECIAL LANGUAGE COLOR TEMP.
- The RS-232C input jack is used to control the Monitor’s functions using an external control device. Type of connector : D-Sub 9-pin male No.
External Control Device Setup 01. Power (Command:p) G To control Power On/Off of the Monitor. Transmission [k][a][ ][Set ID][ ][Data][Cr] Data 0 : Power Off 1 : Power On Acknowledgement Transmission / Receiving Protocol [a][ ][Set ID][ ][OK][Data][x] Data 0 : Power Off 1 : Power On Transmission [Command1][Command2][ ][Set ID][ ][Data][Cr] G To show Power On/Off. * [Command1] : * [Command2] : : * [Set ID] * [DATA] : * [Cr] : * [ ] : To classify factory-adjustment mode or user adjustment mode.
03. Aspect Ratio (Command:c) Transmission 06. Volume control (Command:f) G To adjust volume. You can also adjust volume with the VOL buttons on remote control. Transmission [k][c][ ][Set ID][ ][Data][Cr] [k][f][ ][Set ID][ ][Data][Cr] Data 0 : Wide screen (16:9) 1 : Normal screen (4:3) 2 : Full screen (Zoom) Data Min : 0 ~ Max : 64 * Transmit as Hexadecimal code.
External Control Device Setup 09. Color (Command:i) 12. OSD select (Command:l) G To adjust the screen color. You can also adjust color in the Picture menu. G To select OSD (On Screen Display) on/off. Transmission [k][l][ ][Set ID][ ][Data][Cr] [k][i][ ][Set ID][ ][Data][Cr] Data 0 : OSD off 1 : OSD on Data Min : 0 ~ Max : 64 * Transmit as Hexadecimal code. Acknowledgement [i][ ][Set ID][ ][OK][Data][X] Data Min : 0 ~ Max : 64 10.
15. PIP size (Command:e) ENGLISH 17. Treble (Command:r) G To select PIP size. Transmission G To adjust the screen treble. You can also adjust treble in the sound menu. [k][o][ ][Set ID][ ][Data][Cr] Transmission Data 0 : Normal screen (4:3) 1 : Wide screen (16:9) Acknowledgement [o][ ][Set ID][ ][OK][Data][X] Data 0 : Normal screen (4:3) 1 : Wide screen (16:9) 16. PIP position (Command:q) G To select sub picture position for PIP.
External Control Device Setup 20. Color temperature (Command:u) G To set up with ‘normal, cool, warm, user’ in the color temperature. Transmission [k][u][ ][Set ID][ ][Data][Cr] Data 0 1 2 3 : : : : Normal Cool Warm User 23. B-Adjust (Command:$) G To adjust ‘B-adjust’ in the color temperature. Transmission [k][$][ ][Set ID][ ][Data][Cr] Data Min : 0 ~ Max : 64 * Transmit as Hexadecimal code.
• Check whether the Monitor is turned on. No picture & No sound Picture OK & No sound • Power cord inserted into wall outlet? • Plug another product’s power cord into the wall outlet where the Monitor’s power cord was plugged in. • Press the VOLUME (G) button. • Sound muted? Press MUTE button. • Check to see if there is any object between the LCD Monitor and the remote control causing obstruction.
Troubleshooting check list No output from one of the speakers Picture appears slowly, after switching on 60 • Adjust BALANCE in the SOUND menu. (Refer to 35 page) • This is normal as the image is muted during the startup process of the monitor. Please contact your service centre,if the picture has not appeared after five minutes. Horizontal/vertical bars or picture shaking • Check for local interference such as an electrical appliance or power tool.
ENGLISH Note 61
Note 62
MODEL MW-30LZ10 Width (inches / mm) 29.9 / 759 Height (inches / mm) 21.5 / 546 Depth (inches / mm) 7.1 / 179.5 Weight (pounds / kg) 40.6 / 18.4 Power requirement AC 100-240V~ 50/60Hz Resolution 1280 x 768(Dot) Colors 16,770,000 (256 steps of each R, G, and B) ENGLISH Product specifications • The specifications shown above may be changed without prior notice for quality improvement.