24 Using the PROJECTOR * The initial settings are completed when you select the settings above. Focus and Position of the Screen Image When an image appears on the screen, check if it is in focus and fits the screen properly. To adjust the focus of the image, rotate the focus ring.
Using the PROJECTOR 25 Additional Options Using the Keystone Function Adjusting Aspect Ratio To prevent the screen image from becoming trapezoidal, Keystone adjusts the top and bottom width of the image if the projector is not set up at a right angle to the screen. Because the Keystone function may cause inferior screen image quality, use this function only when it is not possible to set up the projector at an optimal angle. yyPress the SETTINGS button on the remote control.
26 Using the PROJECTOR Changing input device To use SIMPLINK To select an external input Selects external input. yyPress the INPUT button on the remote control to display the input selection screen. - Connected inputs are displayed first. However, AV is always activated. yySelect an input signal using the remote control's INPUT button to connect the projector to the desired input. You can use the or button to switch between all the input modes. INPUT LIST Select an input device to view.
Using the PROJECTOR NOTE yyThis function only works on devices ). with the SIMPLINK logo ( Verify that the external device has a SIMPLINK logo. yyTo use the SIMPLINK function, you need to use a high-speed HDMI® cable (with CEC, or Consumer Electronics Control, feature added). High-speed HDMI® cables have the No. 13 pin connected for information exchange between devices. yyTurn on or select the media of a device with home theatre features to see the speaker switch to External Speaker.
28 Using the PROJECTOR Using the Quick Menu You can customize frequently used menus. 1 Press the Q.MENU button. 2 Press the or button to select a menu and press OK. Menu Aspect Ratio Picture Mode Sound Mode Sleep Timer Description Resizes the picture. Changes the picture mode. Sets the sound mode. Sets the projector to be turned off at the specified time. Adjusts the brightness. Energy Saving AV Mode Sets the mode. Mode Off You can watch using the settings in the video/audio menu.
Using the PROJECTOR To set Sound To set sound output yyPress the SETTINGS button on the remote control. Select SOUND → Sound Out → External Speaker (Optical/HDMI ARC) → ARC Mode. Menu To use projector’s speakers Even when the connected ARC-supported external audio device is turned on, audio output is not automatically processed through the external audio device's speakers.
30 Using the PROJECTOR yyPress the SETTINGS button on the remote control. Select SOUND → Sound Out → External Speaker (Optical/HDMI ARC) → Digital Sound Out. Item Sound Input Auto MPEG Digital Sound Out PCM Dolby Digital Dolby Digital Dolby Digital Plus Dolby Digital HE-AAC PCM All Dolby Digital PCM To connect and use LG audio device LG audio device allows you to enjoy rich powerful sound easily. yyWired Connection: Press the SETTINGS button on the remote control.
Using the PROJECTOR NOTE yyYou can use the projector remote control to adjust the volume of the connected device. yyFor wireless connection, if the device fails to connect. Check the device power to connect and if the LG Audio device is in a proper operating condition. yyIf you select LG Sound Sync (Wireless), devices available for connection are searched and one of searched devices is automatically connected. When a device is connected, its name is shown.
32 ENTERTAINMENT ENTERTAINMENT To connect to a network through Set Expert To connect network For use in special circumstances such as in offices (in cases where a static IP is used). A wireless or wired network connection is required to use the DLNA function. One-click network connection Connects easily to a wired/wireless network. yyPress the SETTINGS button on the remote control. NETWORK → Network connection to connect to an available network automatically. Follow the prompts on the projector.
ENTERTAINMENT 33 To use the Wi-Fi Direct function 2 Enable the Miracast™/Intel’s WiDi Wi-Fi Direct is a function that allows your projector to connect with a Wi-Fi Direct device without Internet connection. With SmartShare™, you can watch the files stored on a device connected via Wi-Fi Direct. 3 A list of devices that can be yyPress the SETTINGS button on the remote control. Select NETWORK → Wi-Fi Direct. 1 Set Wi-Fi Direct to On. (If you do not use it, please change it to Off.
34 ENTERTAINMENT Tips for Network Settings yyUse a standard LAN cable (Cat5 or higher with RJ45 connector, 10 Base-T or 100 Base TX LAN port). yyResetting your modem can cause network connection problems. To resolve the problem, turn the power off, disconnect and reconnect, and then turn the power back on. yyArtograph is not responsible for any network connection problems or any faults, malfunctions and errors caused by an network connection.
SMARTSHARE SMARTSHARE Before Using Connecting a USB Device Connect a USB device (external HDD, USB memory) to the USB port of projector to enjoy the content files stored in the USB device with your projector. You cannot write or delete data in the USB device. Connect a USB flash drive as shown below. USB Flash Drive 35 Removing a USB Device 1 Click the Q.MENU button. 2 Use the or button to move to USB Device and press the OK button. 3 Select a USB to remove.
36 SMARTSHARE Tips for Using a USB Device yyIf the USB storage device has a builtin auto recognition program or uses its own driver, it may not work. yySome USB storage devices may not work or may work incorrectly. yyIf you use a USB extension cable, the USB device may not be recognized or may not work properly. yyUse only USB storage devices formatted with the Windows FAT32 or NTFS file system.
SMARTSHARE 37 To use SmartShare™ 1 Press the SETTINGS button on the remote control. 2 Select SMART SHARE. You can watch the photo, music, video and document on the projector by connecting a USB or home network (DLNA). The photo, music, video and document files of all devices connected to the projector are displayed. (For the document files, only those in the devices connected via USB are displayed.
38 SMARTSHARE Watching the Videos In the Movie List, you can watch movies stored on the connected USB device. Controls playback and sets options while viewing videos. Playing video - warning yySome subtitles created by users may not work properly. yyThe video and subtitle files should be placed in the same folder. For subtitles to display correctly, the video and subtitle files must have the same name.
SMARTSHARE 39 To control video playback You can control playback using the following buttons. Option Shows the current playing position. Use the move forward or backward. Item or button to Description Resumes normal playback. Pauses the video player. Displays in slow motion. Whenever this button is pressed, the playback speed is increased or decreased by one unit. ꕙ Plays the previous/next file. ꕙ Option Sets the option.
