G Order Number : GETEC-C1-13-142 FCC Part 15 subpart B Test Report Number : GETEC-E3-13-035 Page 1 / 1 APPENDIX G : USER’S MANUAL EUT Type: DLP PROJECTOR FCC ID.
Owner's Manual DLP PROJECTOR Please read this manual carefully before operating your projector and retain it for future reference. PG65U P/NO :SAC30666059 (1303-REV00) www.lg.
2 LICENSES LICENSES Supported licenses may differ by model. For more information about licenses, visit www.lg.com. Manufactured under license from Dolby Laboratories. “Dolby “and the double-D symbol are trademarks of Dolby Laboratories. ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a subsidiary of Rovi Corporation. . This is an official DivX Certified® device that plays DivX video. Visit divx.com for more information and software tools to convert your files into DivX video.
SAFETY INSTRUCTIONS 3 SAFETY INSTRUCTIONS Please take note of the safety instructions to prevent any potential accident or misuse of the projector. y Safety precautions are given in two forms, i.e. Warning and Caution as detailed below. WARNING: Failure to follow the instructions may cause serious injury and even death. CAUTION: Failure to follow the instructions may cause injury to persons or damage to the product. y Read the owner's manual carefully and keep it to hand.
4 SAFETY INSTRUCTIONS y Do not place the projector where it might be exposed to excessive dust. - This may cause a fire. y Do not use the projector in a damp place such as a bathroom where it is likely to get wet. - This may cause a fire or an electric shock. y Do not allow a tablecloth or curtain to block the vents. - This may cause the internal temperature of the projector to rise and cause a fire. y The distance between the projector and the wall should be more than 30 cm for ventilation purposes.
SAFETY INSTRUCTIONS CAUTION y Hold the plug firmly when unplugging. - A broken wire in the cord may cause a fire. y Ensure the power cord or plug is not damaged, modified, severely bent, twisted, pulled, sandwiched or heated. Do not use a loose wall outlet. - This may cause a fire or an electric shock. y Keep the power cord away from any heating devices. - The cord coating may melt and cause an electric shock.
6 SAFETY INSTRUCTIONS y Do not look directly into the lens when the projector is in use. The strong light may damage your eyes. y When the lamp is on or has just been turned off, avoid touching the air vent or lamp because these will be very hot. y If there is a gas leak, do not touch the wall outlet. Open the window for ventilation. - A spark may cause a fire or burn. y Never touch the projector or power cord during thunder or lightning. - This may cause an electric shock.
SAFETY INSTRUCTIONS Cleaning WARNING y Do not spray the projector with water when cleaning. Do not allow water to go into the projector or do not allow it to get wet. - This may cause a fire or an electric shock. y When there is smoke or a strange smell coming out from the projector or a foreign object falls into the projector, please switch it off and unplug it from the power outlet and contact an LG Electronics Service Center. - If not, this may cause a fire or an electric shock.
8 SAFETY INSTRUCTIONS OTHERS WARNING y Only a qualified technician can disassemble or modify the projector. For inspection, adjustment, or repair, contact your seller or the Service Center. - Otherwise, this may cause a fire or an electric shock. y Dispose of the used battery properly. - Otherwise, this may result in explosion or fire. y The correct method of disposal may vary depending on your country or region. Dispose of the battery pack according to the appropriate instructions.
SAFETY INSTRUCTIONS FCC NOTICE ANTENNA Outdoor Antenna Grounding y If an outdoor antenna is installed, follow the precautions below. An outdoor antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can come in contact with such power lines or circuits as death or serious injury can occur. Be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges.
10 SAFETY INSTRUCTIONS IC (CANADA) Industry Canada Statement: This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: 1) this device may not cause interference and 2) this device must accept any interference, including interference that may cause undesired operation of the device. Avis d’Industrie Canada : Cet appareil est conforme à la norme CNR-210 des règlements d’Industrie Canada.
SAFETY INSTRUCTIONS Disposal of your old appliance 1. When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC. 2. All electrical and electronic products should be disposed of separately from the municipal waste stream through designated collection facilities appointed by your government or your local authorities. 3.
12 Contents Contents LICENSES 2 SAFETY INSTRUCTIONS 3 PREPARATION 13 Accessories Optional Extras Parts and Components Installation - Installation Precautions - Connecting an adapter - Projection Distance per Screen Size - Using the Lens Hood - Using the Cradle scene - Connecting a battery - How to Install the Projector On a Tripod - Kensington Security System 13 14 15 16 16 16 20 20 REMOTE CONTROL 21 17 18 18 19 USING THE PROJECTOR 23 Connecting to an Antenna or Cable - Connecting an Antenna
PREPARATION PREPARATION Accessories Check enclosed accessories. The picture may be different from an actual product. Remote Control Coin Battery (CR 2032) Owner's Manual RF Cable Adapter Power Cord Owner's Manual CD Hood Battery Cradle Composite video cable Bag y When connecting a cable to the HDMI or USB port, it may not be connected properly if the size of jack to the USB/HDMI port is too big. Use a standard sized jack.
14 PREPARATION Optional Extras To purchase optional extras, visit an electronics store or online shopping site or contact the retail store where you purchased the product. Without prior notice, optional extras are subject to change in order to improve the performance of the product, and new accessories may be added.
PREPARATION 15 Parts and Components * The projector is manufactured using high-precision technology. You may, however, see tiny black dots and/or bright colored dots (red, blue or green) that continuously appear on the projector screen. This is a normal result of the manufacturing process and does not indicate a malfunction. When powered on, the LED of the control panel turns on.
16 PREPARATION Installation Installation Precautions y Place the projector in a well-ventilated environment. - To prevent internal heat from building up, install the projector in a wellventilated place. Do not place anything near the projector as this may block the air vents. If the air vents are blocked, the internal temperature will increase. - Do not place the projector on a carpet or rug. Do not block any vents on the bottom and use the projector on a leveled solid surface.
PREPARATION 17 Projection Distance per Screen Size 1 Place the projector on a sturdy, level surface, together with the PC or audio/video source. 2 Place the projector at an appropriate distance from the screen. The distance between the projector and the screen determines the actual size of the image. 3 Position the projector so that the lens is set at a right angle to the screen. If the projector is not set at a right angle, the image on the screen will be tilted and the image quality will be poor.
18 PREPARATION Using the Lens Hood Turn the lens hood as shown by the arrow.
PREPARATION Connecting a battery 1. Assemble the projector as shown. س 2. Turn the knob as shown by the arrow.
20 PREPARATION How to Install the Projector On a Tripod y You can install this projector on a camera tripod as shown below. y When stabilizing the tripod, we recommend using a locking bolt of standard size 4.5 mm or less. The maximum size allowed for the locking bolt is 5.5 mm. (If it is longer than the maximum allowed size, it may damage the projector.) Bottom side of the projector Bolt used to attach the projector س + The projector is connected to this part.
REMOTE CONTROL 21 REMOTE CONTROL Open the battery cover on the back of the remote control and insert the specified batteries as per instructions . The same type of batteries must be used. ① ② POWER Turns the projector on or off. INPUT Changes the input source. MUTE Mutes all sounds. VOL +, Adjusts the volume level. CH , Changes the channel or page. PAGE Moves to the previous/next page. INFO Views the information of the current program and screen. BLANK Turns the projector screen on or off.
22 REMOTE CONTROL Number buttons Enter a number. Playback Control Buttons Controls playback of USB mode. LIST Accesses the saved channel list. - (Dash) Inserts a dash between numbers such as 2 - 1 and 2 - 2. FLASHBK Tunes to the last channel viewed. Color buttons Access special functions in some menus. NOTE y When using the remote control, the optimal remote range is less than 3 meters (left/right) and within a 30 degree arc of the IR receiver. y For seamless operation, do not block the IR receiver.
Using the PROJECTOR Using the PROJECTOR Connecting to an Antenna or Cable Connect an antenna, cable, or cable box to watch TV while referring to the following. The illustrations may differ from the actual items and a RF cable is optional. Connecting a Cable Box Connect the projector to a cable box and the cable box to a wall antenna socket with 2 RF cables (75 Ω). Connecting an Antenna or Basic Cable Connect the projector to a wall antenna socket with an RF cable (75 Ω).
24 Using the PROJECTOR Battery using time information Status Time and Display Charging About 3 hours Standard Usage Hours About 2 hour (Available battery using time approximately 1 hour 30 mins when Energy Saving mode set to Max) Battery Level Indicator 1. The battery is automatically recharged when the Projector is connected to a power supply. * Charge the battery fully when you first use the Projector.
Using the PROJECTOR 25 Watching the Projector Turning on the Projector Watching the Projector 1 Connect the power cord correctly. 2 After waiting for a moment, press 1 the POWER button on the remote control or the control panel. (The light on the control panel will be turned on.) 3 In the Language Selection screen, select a language. 4 Select an input signal by using the INPUT button on the remote control.
26 Using the PROJECTOR Managing Channels Setting Up Channels Storing Channels To store channels automatically, 1 Press MENU to access the menu. 2 Press the Navigation buttons to scroll to CHANNEL and press OK. 3 Press the Navigation buttons to scroll to Auto Tuning and press OK. 4 Select Start to start automatic tuning. The projector scans and saves available channels automatically. 5 When you are finished, press SETTINGS. To store channels manually, 1 Press MENU to access the menu.
Using the PROJECTOR Editing Your Channel List Favorite Channel Setup 1 Press MENU to access the menu. 2 Press the Navigation buttons to scroll 1 to CHANNEL and press OK. 3 Press the Navigation buttons to scroll 27 Press CH or Number buttons to access to select your desired channel. 2 Press FAV. to access the Favorite List. 3 Press the /# #buttons to scrolls through channel group. to Channel Edit and press OK. 4 Press the Yellow button. 4 Edit channels using the following buttons.
28 Using the PROJECTOR Using Additional Options Adjusting Aspect Ratio You can also change the image size by pressing Q.MENU or SETTINGS. - 4:3: Resizes images to the 4:3 aspect ratio. NOTE y Some options may not be available depending on input signals. - FULL: Changes to the full screen regardless of the aspect ratio. - 16:9: Resizes images to fit the screen width. - Zoom: Enlarges an image to fit the screen width. The top and bottom of the image may be truncated.
29 Using the PROJECTOR Using the Keystone Function Using the Input List To prevent the screen image from becoming trapezoidal, Keystone adjusts the top and bottom width of the image if the projector is not set at a right angle to the screen. Because the Keystone function may cause inferior screen image quality, use this function only when it is not possible to set up the projector at an optimal angle. ؒ.H\VWRQH Using the Input List 1 Press the INPUT button to access the input sources.
