Technical Specification Product: LTE Modem (Model: TM13LNCAHK2) 1/15
History Ver. Date 1.0 2020.1.
Contents 1. Product Introduction ...................................................................................................... 4 1.1 Block Diagram ...................................................................................................... 4 1.2 Environmental Specifications ............................................................................... 5 1.3 Electrical Specifications ....................................................................................... 5 1.3.
1. Product Introuction The TM13LNCAHK2 are designed for the automotive industry. They support LTE and WCDMA air Interface standards. The TM13LNCAHK2 are based on the Qualcomm MDM9628 wireless chipsets and support the following bands. Table 1.
1.2 Environmental Specifications The environmental specification for operating and storage of the TM13LNCAHK2 are defined in the the table below. Table 2. Environmental Specifications Parameter Temperature Range Operating Temperature -40℃ to 85℃ Storage Temperature -40℃ to +90℃ Humidity 95% or less 1.3 Electrical Specifications This section provides details for some of the key electrical specifications of the TM13LNCAHK2 embedded modules. 1.3.
1.3.2 Current Consumption Table 4. TM13LNCAHK2 Current Consumption (TBD) Mode Parameter Typical Max Max TX Output /Full RB 600 650 mA 600 3.6 650 4.0 mA mA Idle, Registered 3.6 4.0 mA LTE Sleep Mode, Average Current 1.8 2.2 mA CDMA/WCDMA Sleep Mode, Average Current 1.8 2.2 mA LTE CDMA/WCDMA Max TX Output LTE Idle, Registered CDMA/WCDMA Units 1.4 Mechanical Specifications 1.4.
2. RF Specification The specifications for the LTE and WCDMA interfaces are defined. TM13LNCAHK2 is designed to be compliant with the standard shown in the table below. Table6. Standards Compliance Technology Standards LTE • 3GPP Release 8 CDMA • 3GPP2 Release IxEVDO, REV.H WCDMA • 3GPP Release 9 2.1 LTE Specification 2.1.1 LTE TX Output Power The Maximum / Minimum Transmitter Output Power of the TM13LNCAHK2 are specified in the following table. Table7.
BAND 2 Reference sensitivity level(DUAL) BAND 4 Reference sensitivity level(DUAL) BAND 5 Reference sensitivity level(DUAL) BAND 7 Reference sensitivity level(DUAL) BAND 12 Reference sensitivity level(DUAL) BAND 17 Reference sensitivity level(DUAL) Measure BLER of Mid Channel (900) in Band2 sensitivity : ≤-95 BLER : ≤ 5% Measure BLER of Mid Channel (2175) in Band4 sensitivity : ≤-97 BLER : ≤ 5% Measure BLER of Mid Channel (2525) in Band5 sensitivity : ≤-95 BLER : ≤ 5% Measure BLER of Low Channel (3100
3. NAD Module installation guide - HKMC NAD Module is mounted with solder ball on the main AVN board. 4. Installation guide for external antenna connector 4.1.
4.2.
4.3 Design validation & production procedures To verify compliance of the reference trace, a coupon must be requested with every manufacturing panel form and for which the characteristics are described in the Gerber files.. Then a network analyzer is used to measure the impedance of this coupon in order to validate the antenna trace. Note1. Measurement results delivered with boards. Controlled impedence shall be 50 Ohms +/- 15% on layer TOP 0.
5.
FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
INTEGRATION INSTRUCTIONS The module complies with Part 22/24/27 of the FCC rules. The module complies with RSS-130/132/133/139/199 of the RSS standards. The modular transmitter is only FCC/IC authorized for the specific rule part listed on the grant. The host product manufacturer is responsible for compliance to any other FCC/IC rules that apply to the host not covered by the modular transmitter grant of certification.
Host User Manual The host manual shall include the following regulatory statement; FCC Part 15.19: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Part 15.
