Specifications

ManualsBrandsLG Electronics USA ManualsElectronicsBluetooth Module

Table Of Contents

빈 페이지

1. Module : WB1NP9

This WB1NP9 Module can be easily designed into any embedded system for Bluetooth Spec 5.0

feature. It is based on QCC5125 with specific interface design to meet LG Electronics’s needs.

2. Module Specification

Chips QCC5125

Bluetooth Spec Bluetooth 5.0

Frequency Band 2402 ~ 2480 MHz

Tx Power

2.51mW ~ 6.31mW (Bluetooth Power Class I)

Rx Sensitivity < -70dBm (BER 0.1%)

Distance < 100m (Open Space)

Power Voltage 3.3V

Dimension

23mmⅹ20mm ⅹ3 mm

Environmental Range Operation temperature : -30 ~ +70℃

Modulation GFSK, π/4-DQPSK

Communication Method FHSS

Summary of content (7 pages)

PAGE 1
. Module : WB1NP9 This WB1NP9 Module can be easily designed into any embedded system for Bluetooth Spec 5.0 feature. It is based on QCC5125 with specific interface design to meet LG Electronics’s needs. 2. Module Specification Chips QCC5125 Bluetooth Spec Bluetooth 5.0 Frequency Band 2402 ~ 2480 MHz Tx Power 2.51mW ~ 6.31mW (Bluetooth Power Class I) Rx Sensitivity < -70dBm (BER 0.1%) Distance < 100m (Open Space) Power Voltage 3.
PAGE 2
Conditions : VDD = 3.3V, Ta = 25 ℃, unless otherwise noted. Absolute Maximum Ratings Parameter Min Max Unit Power Supply Voltage : VDD -0.4V 3.6V DCV -40 85 ℃ Parameter Min Max Unit Power Supply Voltage 3.0V 3.6V DCV Operation Temperature -30 70 ℃ Storage Temperature Recommended Operating Conditions Current consumption Parameter Connection Avg Peak Unit - <1 1 mA - <1 1 mA ACL No data transfer Master 1 1.
PAGE 3
General Performance Parameter Condition Min Typ Max Unit Normal 2402 - 2480 MHz Condition Min Avg Max Unit Normal 4 - 8 dBm Condition Min Typ Max Unit Power density Normal - - <20 dBm 20dB bandwidth Normal 1000 KHz Frequency Range Transmitter Performance Parameter Transmit Power Parameter Adjacent channel power (F0 = 2441MHz) Out-band Spurious Emission Modulation Characteristic Initial Carrier Frequency Tolerance Carrier Frequency Drift F=F0 ±2MHz - - -20 dBm F=F
PAGE 4
Maximum received signal at 0.
PAGE 5
FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) This device must accept any interference received, including interference that may cause undesired operation of the device. Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
PAGE 6
DOCUMENT No : REG. DATE : REV. DATE : - User Manual MODEL NAME: WB1NP9 - REV.NO : V1.0 PAGE : 0 / 9 2.2 List of applicable FCC rules This module has been granted modular approval as below listed FCC rule parts. - FCC Rule parts 15C(15.247) 2.3 Summarize the specific operational use conditions - The OEM integrator should use equivalent antennas which is the same type and equal or less gain then an antenna listed in 2.
PAGE 7
DOCUMENT No : REG. DATE : REV. DATE : - User Manual MODEL NAME: WB1NP9 - REV.NO : V1.0 PAGE : 1 / 9 2.8 Label and compliance information End Product Labeling The module is labeled with its own FCC ID and IC Certification Number. If the FCC ID and IC Certification Number are not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module.