User Manual PRODUCT NAME : ZigBee Module MODEL NAME WZB1NP6(TWZM-V302D) : The information contained herein is the exclusive property of LG Innotek and shall not be distributed, reproduced or disclosed in whole or no in part without prior written permission of LG Innotek.
User Manual REG. DATE : 2015.11.27 REV. DATE : 2015.11.27 MODEL: WZB1NP6(TWZM-V302D) REV.NO : 1.0 PAGE : 1 / 7 Table of Contents No. Description Page 1 Features 2 2 Module Photo 2 3 Block Diagram 3 4 Storage Conditions 4 5 Operating Conditions 4 6 Interface Specification 5 7 Pin Description 6 8 Outline Drawing 7 9 Packing Information 8 © 2015 LGIT. All rights reserved.
User Manual REG. DATE : 2015.11.27 REV. DATE : 2015.11.27 REV.NO : 1.0 MODEL: WZB1NP6(TWZM-V302D) PAGE : 2 / 7 1. Features TWZM-V302D is the small size and low power module for ZigBee. TWZM-V302D is based on Silicon Labs EM3588. 2.4GHz IEEE802.15.4 compliant RF Transceiver Excellent Receiver Sensitivity and Robustness to interference Size : 34mm x 27mm x 3.7 mm High performance and Low power 32-bit RISC CPU 512-KB Flash Memory and 64_KB SRAM Memory USB 2.
User Manual REG. DATE : 2015.11.27 REV. DATE : 2015.11.27 MODEL: WZB1NP6(TWZM-V302D) 3. Block Diagram © 2015 LGIT. All rights reserved. REV.NO : 1.
User Manual REG. DATE : 2015.11.27 REV. DATE : 2015.11.27 REV.NO : 1.0 MODEL: WZB1NP6(TWZM-V302D) PAGE : 4 / 7 4. Storage Conditions Parameter Min Max Unit Storage Temperature -10 +80 ℃ Storage Humidity (@ 40℃) - 90 % Caution : The specifications above the Table define levels at which permanent damage to the device can occur. Function operation is not guaranteed under these conditions.
User Manual REG. DATE : 2015.11.27 REV.NO : 1.0 MODEL: WZB1NP6(TWZM-V302D) REV. DATE : 2015.11.27 PAGE : 5 / 7 6. Pin Description Pin No. 1 2 3 4 5 6 7 8 Pin Name GND UPDATE GND RESET GND USB_DP USB_DN VCC(+3.3V) I/O GND I/O GND I GND I/O I/O I Pin Description GROUND Digital I/O, F/W UPDATE GROUND Active Low chip reset GROUND USB Positvie USB Negative Power supply(+3.3V) < TOP View > < Bottom View > A 8 1 Note. 1) Recommend a Module install sequence for prevent UART device failure - Supply 3.
User Manual REG. DATE : 2015.11.27 REV. DATE : 2015.11.27 MODEL: WZB1NP6(TWZM-V302D) 7. Outline Drawing © 2015 LGIT. All rights reserved. REV.NO : 1.
User Manual REG. DATE : 2015.11.27 REV. DATE : 2015.11.27 MODEL: WZB1NP6(TWZM-V302D) 8. Packing Information © 2015 LGIT. All rights reserved. REV.NO : 1.
FCC Information This device complies with part 15 of the FCC Results. Operation is subject to the following two conditions : (1) This device may not cause harmful interface, and (2) This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for CLASS B digital device, pursuant to Part 15 of FCC Rules.
Information for OEM Integrator This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. End product labelling The label for end product must include “Contains FCC ID: BEJ-WZB1NP6, IC: 2703K-WZB1NP6”. "CAUTION : Exposure to Radio Frequency Radiation.