OWNER’S MANUAL LCD TV Please read this manual carefully before operating your set and retain it for future reference. 26LD360L 32LD360L The model and serial number of the TV is located on the back and one side of the TV. Record it below should you ever need service. 26LD350C 32LD350C MODEL SERIAL P/NO : SAC34026005 (1004-REV00) www.lg.
WARNING / CAUTION WARNING / CAUTION To prevent fire or shock hazards, do not expose this product to rain or moisture. TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.
SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. 1 2 Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 7 Only use attachments/accessories specified by the manufacturer. 8 Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.
SAFETY INSTRUCTIONS 4 11 Never touch this apparatus or antenna during a thunder or lighting storm. 12 When mounting a TV on the wall, make sure not to install the TV by the hanging power and signal cables on the back of the TV. 13 Do not allow an impact shock or any objects to fall into the product, and do not drop onto the screen with something.
20 ANTENNAS Outdoor antenna grounding If an outdoor antenna is installed, follow the precautions below. An outdoor antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can come in contact with such power lines or circuits as death or serious injury can occur. Be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges.
CONTENTS WARNING / CAUTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 3 FEATURES OF THIS TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 PREPARATION Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Front Panel Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Back Panel Information . . . . . . . . .
SOUND & LANGUAGE CONTROL Auto Volume Leveler (Auto Volume) . . . . . . . . . . . . . . . . . 73 Clear Voice II . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Preset Sound Setting (Sound Mode) . . . . . . . . . . . . . . . . 75 Sound Setting Adjustment - User Mode . . . . . . . . . . . 76 Infinite Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 Balance . . . . . . . . . . . . . . . . . . . . .
FEATURES OF THIS TV High-definition television. High-resolution digital television broadcast and playback system composed of roughly a million or more pixels, 16:9 aspect-ratio screens, and AC3 digital audio. A subset of digital television, HDTV formats include 1080p, 1080i, and 720p resolutions. This TV contains the detailed calibrations necessary for professional certification by the Imaging Science Foundation.
PREPARATION ACCESSORIES EN ER GY AV SA VING MO DE IN PU 1 2 4 LIS VO RA TI MU TE U 0 MA L MEN FA V FO TE R 9 AS HB CH E A G M UTE O N FL RK K O FF O IN EN TV 6 8 T T 3 5 7 Vo P Q. MEN U lum e Cha PREPARATION Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the dealer where you purchased the TV. The accessories included may differ from the images below. nn el BA CK EX IT Owner’s Manual CD Manual 1.
PREPARATION FRONT PANEL INFORMATION ■ Image shown may differ from your TV. PREPARATION CH CHANNEL ( Buttons , VOL VOLUME (+, -) Buttons ENTER Button ENTER MENU Button MENU INPUT Button SPEAKER INPUT POWER Button Remote Control Sensor Power/Standby Indicator Illuminates red in standby mode. Illuminates blue when the TV is switched on.
BACK PANEL INFORMATION ■ Image shown may differ from your TV. PREPARATION AC IN 1 1 2 3 2 RJP 4 5 REMOTE CONTROL IN USB IN 12 6 11 RS-232C IN (CONTROL&SERVICE) /DVI IN VIDEO L(MONO)- AUDIO- R EXTERNAL SPEAKER OUT L R AUDIO IN (RGB/DVI) Y OPTICAL DIGITAL AUDIO OUT 10 1 2 L 9 RGB IN (PC) Analog PC Connection. Uses a D-sub 15 pin cable (VGA cable). AUDIO IN (RGB/DVI) 1/8" (0.32 cm) headphone jack for analog PC audio input.
PREPARATION STAND INSTRUCTIONS ■ Image shown may differ from your TV. PREPARATION INSTALLATION 1 Carefully place the TV screen side down on a cushioned surface to protect the screen from damage. 2 Assemble the parts of the S T A N D B O D Y with C O V E R B A S E of the TV by using the 4 screws supplied. STAND BODY (M4x20) COVER BASE 3 Assemble the TV as shown. 4 Fix the 4 screws securely using the holes in the back of the TV.
DETACHMENT Carefully place the TV screen side down on a cushioned surface to protect the screen from damage. 2 Remove the screws from the TV. 3 Detach the stand from TV. PREPARATION 1 PROTECTION COVER After removing the stand, install the included p r o t e c t i o n c o v e r over the hole for the stand. Press the P R O T E C T I O N C O V E R into the TV until you hear it click.
PREPARATION VESA WALL MOUNTING PREPARATION Install your wall mount on a solid wall perpendicular to the floor. When attaching to other building materials, please contact your nearest installer. If installed on a ceiling or slanted wall, it may fall and result in severe personal injury. We recommend that you use an LG brand wall mount when mounting the TV to a wall. LG recommends that wall mounting be performed by a qualified professional installer.
AC IN AC IN CABLE MANAGEMENT ■ Image shown may differ from your TV. Connect the cables as necessary. To connect additional equipment, see the EXTERNAL EQUIPMENT SETUP section. Secure the power cable with the P R O T E CT I V E B R A C K E T and S C R E W as shown. It will help prevent the power cable from being removed by accident. 2 Open the CABLE MANAGEMENT CLIP as shown.
PREPARATION DESKTOP PEDESTAL INSTALLATION ■ Image shown may differ from your TV. For proper ventilation, allow a clearance of 4 inches on all four sides from the wall. PREPARATION 4 inches 4 inches 4 inches 4 inches CAUTION G G Ensure adequate ventilation by following the clearance recommendations. Do not mount near or above any type of heat source. SWIVEL STAND After installing the TV, you can adjust the TV set manually to the left or right direction by 20 degrees to suit your viewing position.
ATTACHING THE TV TO A DESK The TV must be attached to a desk so it cannot be pulled in a forward/backward direction, potentially causing injury or damaging the product. PREPARATION Stand Desk 4-Screws (not provided as parts of the product) GScrews: M5 x L (*L: Table depth + 8-10 mm) ex) Table depth: 15mm, Screw: M5 x 25 Stand 1-Screw (provided as parts of the product) Desk WARNING G To prevent TV from falling over, the TV should be securely attached to the floor/wall per installation instructions.
PREPARATION SECURING THE TV TO THE WALL TO PREVENT FALLING WHEN THE TV IS USED ON A STAND ■ PREPARATION ■ You should purchase necessary components to prevent the TV from tipping over (when not using a wall mount). Image shown may differ from your TV. We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards. Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction, potentially causing injury or damaging the product.
■ ■ To prevent damage do not connect to the power outlet until all connections are made between the devices. Image shown may differ from your TV. ANTENNA OR CABLE CONNECTION PREPARATION 1. Antenna (Analog or Digital) Wall Antenna Socket or Outdoor Antenna without a Cable Box Connections. For optimum picture quality, adjust antenna direction if needed.
EXTERNAL EQUIPMENT SETUP ■ To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment HD RECEIVER SETUP This TV can receive digital over-the-air/digital cable signals without an external digital set-top box. However, if you do receive digital signals from a digital set-top box or other digital external device. EXTERNAL EQUIPMENT SETUP Component Connection Y PB PR L R 1.
HDMI Connection 1. How to connect 1 Connect the digital set-top box to the H D M I / D V I I N 1 or 2 jack on the TV. 1 RGB IN (PC) RJP REMOTE CONTROL IN RS-232 (CONTROL& 1 AV IN 1 VIDEO L(MONO) AUDIO R EXT L AUDIO IN (RGB/DVI) OPTICAL DIGITAL AUDIO OUT 2. How to use Y PB PR L COMPONENT IN Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.) ■ Select the H D M I 1 or HDMI2 input source on the TV using the INPUT button on the remote control.
EXTERNAL EQUIPMENT SETUP DVI to HDMI Connection 1. How to connect Connect the DVI output of the digital set-top box to the H D M I / D V I I N 1 or H D M I / D V I I N 2 jack on the TV. 1 /DVI IN EXTERNAL EQUIPMENT SETUP 1 RGB IN (PC) RJP REMOTE CONTROL IN AV IN 1 RS-232C IN (CONTROL&SERVICE 1 VIDEO L(MONO) AUDIO R EXTERNAL L R AUDIO IN (RGB/DVI) 2 Connect the digital set-top box audio output to the A U D I O I N ( R G B / D V I ) jack on the TV. OPTICAL DIGITAL AUDIO OUT 2.
DVD SETUP Component Connection Y PB PR L R 1. How to connect Connect the video outputs (Y, PB, PR) of the DVD to the C O M P O N E N T I N V I D E O jacks on the TV. Match the jack colors (Y = green, PB = blue, and PR = red). 2 B IN (PC) 2 2. How to use ■ ■ 2 REMOTE CONTROL IN RS-232C IN (CONTROL&SERVICE) AV IN 1 VIDEO L(MONO) AUDIO R EXTERNAL SPEAKER OUT L R Connect the audio outputs of the DVD to the C O M P O N E N T I N A U D I O jacks on the TV.
EXTERNAL EQUIPMENT SETUP Composite (RCA) Connection 1. How to connect 1 2. How to use ■ ■ ■ Turn on the DVD player, insert a DVD. Select the A V 1 or A V 2 input source on the TV using the I N P U T button on the remote control. Refer to the DVD player's manual for operating instructions. 1 /DVI IN EXTERNAL EQUIPMENT SETUP V I D E O jacks between TV and Connect the A U D I O/V DVD. Match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red).
VCR SETUP Antenna Connection 1. How to connect UDIO R 1 R IO 2 ANT OUT ANTENNA /CABLE IN S-VIDEO VIDEO L R AUDIO ANT IN Connect the antenna cable to the RF antenna in socket of the VCR. OUTPUT SWITCH Wall Jack 2 2. How to use ■ ■ Set VCR output switch to 3 or 4 and then tune TV to the same channel number. Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.
EXTERNAL EQUIPMENT SETUP OTHER A/V SOURCE SETUP 1. How to connect ■ ■ Select the A V 1 or A V 2 input source on the TV using the I N P U T button on the remote control. Operate the corresponding external equipment. R USB IN L IN 2 2. How to use VIDEO 1 VIDEO L/MONO AUDIO R EXTERNAL EQUIPMENT SETUP V I D E O jacks Connect the A U D I O/V between TV and external equipment. Match the jack colors.
AUDIO OUT CONNECTION Send the TV’s audio to external audio equipment via the Audio Output port. If you want to enjoy digital broadcasting through 5.1-channel speakers, connect the OPTICAL DIGITAL AUDIO OUT terminal on the back of TV to a Home Theater (or amp). 1. How to connect 2 Connect the other end of the optical cable to the digital audio input on the audio equipment.
EXTERNAL EQUIPMENT SETUP PC SETUP This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings. VGA (D-Sub 15 pin) Connection 1. How to connect Connect the VGA output of the PC to the R G B I N ( P C) jack on the TV. 2 Connect the PC audio output to the A U D I O I N ( R G B / D V I) jack on the TV.
! NOTES To get the the best picture quality, adjust the PC graphics card to 1360x768. G The synchronization input form for Horizontal and Vertical frequencies is separate. G Depending on the graphics card, DOS mode may not work if a HDMI to DVI Cable is in use. G G In PC mode, there may be noise associated with the resolution, vertical pattern, contrast or brightness.
EXTERNAL EQUIPMENT SETUP Screen Setup for PC mode Selecting Resolution PICTURE Move SCREEN Enter • Contrast 50 • Brightness 50 • Sharpness 50 • Color 50 • Tint 0 Resolution Auto Config. Position R G • Advanced Control Size • Picture Reset Screen (RGB-PC) Phase Reset 1 MENU Select P I C T U R E. ENTER Select S c r e e n ( R G B - P C ). ENTER Select R e s o l u t i o n. ENTER Select the desired resolution.
Auto Configure Automatically adjusts picture position and minimizes image instability. After adjustment, if the image is still not correct, try using the manual settings or a different resolution or refresh rate on the PC. Move SCREEN Enter Move Prev. E • Contrast 50 • Brightness 50 • Sharpness 50 • Color 50 • Tint 0 Resolution Auto Config.
EXTERNAL EQUIPMENT SETUP Adjustment for screen Position, Size, and Phase If the picture is not clear after auto adjustment and especially if characters are still trembling, adjust the picture phase manually. This feature operates only in RGB-PC mode. PICTURE Move SCREEN Enter E EXTERNAL EQUIPMENT SETUP • Contrast 50 • Brightness 50 • Sharpness 50 • Color 50 Move Prev. Resolution Auto Config.
WATCHING TV / CHANNEL CONTROL REMOTE CONTROL FUNCTIONS When using the remote control, aim it at the remote control sensor on the TV. POWER Turns the TV on from standby or off to standby. ENERGY SAVING Adjusts the Energy Saving. G p.70 AV MODE Toggles through preset Video and Audio modes. G p.49 TV INPUT Rotates through inputs. Also switches the TV on from standby. G p.47 SAVING 1 2 3 4 5 6 7 8 9 0 FLASHBK TV Returns to the last TV channel.
MENU Displays the main menu or clears all on-screen displays and return to TV viewing. ENERGY AV MODE INPUT INFO Displays channel information at the top of the screen. G p.46 TV WATCHING TV / CHANNEL CONTROL Q.MENU Opens the list of Quick Menu options. G p.39 SAVING 1 2 3 4 5 6 7 8 9 0 FLASHBK THUMBSTICK Navigates the on-screen menus and adjusts the system (Up/Down/Left Right/ENTER) settings to your preference.
(For 26/32LD360L) MUTE ON OFF MUTE Switches the sound on or off. ON/OFF G p.36 Turns the TV on from standby or off to standby. Volume Channel CHANNEL Changes the channel. UP/DOWN BED1, 2, 3, 4 Open the battery compartment cover on the back and determines the code set transmitted, Bed 1, Bed 2, Bed 3 or Bed 4. Bed 1, Bed 2, Bed 3 or Bed 4 switch on patient remote. The position of the Bed 1/Bed 2/Bed 3/Bed 4 switch must correspond to the setting in the Installation menu.
WATCHING TV / CHANNEL CONTROL TURNING ON THE TV First, connect power cord correctly. At this moment, the TV switches to standby mode. ■ In standby mode to turn TV on, press the ) button on the TV or press the , I N P U T, C H ( P O W E R, I N P U T, C H ( 9 ) button on the remote control. or ) , N u m b e r ( 0~9 1 2 Select the viewing source by using the I N P U T button on the remote control. ■ This TV is programmed to remember which power state it was last set to, even if the power cord is out.
INITIAL SETTING This Function guides the user to easily set the essential items for viewing the TV for the first time when purchasing the TV. It will be displayed on the screen when turning the TV on for the first time. It can also be activated from the user menus. H o m e U s e”. We recommend setting the TV to “H H o m e U s e” mode for the best picDefault selection is “H ture in your home environment. ■ “S S t o r e D e m o” Mode is only intended for use in retail environments.
WATCHING TV / CHANNEL CONTROL ON-SCREEN MENUS SELECTION Your TV's OSD (On Screen Display) may differ slightly from that shown in this manual.
QUICK MENU Your TV's OSD (On Screen Display) may differ slightly from what is shown in this manual. Q.Menu (Quick Menu) is a menu of features which users might use frequently. A Aspect Ratio F A G WATCHING TV / CHANNEL CONTROL A s p e c t R a t i o: Selects your desired picture format. P i c t u r e M o d e: Selects the factory preset picture depend on the viewing environment. S o u n d M o d e: Selects the factory preset sound for type of program.
WATCHING TV / CHANNEL CONTROL CHANNEL SETUP Auto Scan (Auto Tuning) Automatically finds all channels available through antenna or cable inputs, and stores them in memory on the channel list. Run this function if you change your residence or move the TV. Auto Tuning memorizes only the channels available at the time of scanning. WATCHING TV / CHANNEL CONTROL CHANNEL Move Enter CHANNEL Auto Tuning Manual Tuning Manual Tuning Channel Edit Channel Edit Enter Check your antenna connection.
Add/Delete Channel (Manual Tuning) When selecting DTV or CADTV input signal, you can view the on-screen signal strength monitor to see the quality of the signal being received. CHANNEL Move Enter CHANNEL Move Auto Tuning Manual Tuning Manual Tuning Channel Edit Channel Edit Enter DTV F G Select channel type and RF-channel number. Channel 2 DTV 2-1 Bad Normal Good Delete Close 1 MENU Select C H A N N E L. ENTER Select M a n u a l T u n i n g.
WATCHING TV / CHANNEL CONTROL Channel Editing The channels in the Channel Edit List are displayed in black and the channels deleted from the Channel Edit List are displayed in blue. When a channel number is deleted, it means that you will be unable to select it using C H button during TV viewing. If you wish to select the deleted channel, directly enter the channel number with the NUMBER buttons or select it in the C h a n n e l E d i t menu.
CHANNEL LIST You can check which channels are stored in the memory by displaying the channel list. Channel List This padlock is displayed when the channel is locked with parental control. DTV 2-1 DTV 3-1 DTV 4-1 Displaying Channel List 1 Display the C h a n n e l L i s t. LIST Selecting a channel in the channel list 1 WATCHING TV / CHANNEL CONTROL Exit Select a channel. 2 ENTER Switch to the chosen channel number. Paging through a channel list 1 CH 2 P A G E Turn the pages.
WATCHING TV / CHANNEL CONTROL FAVORITE CHANNEL SETUP Favorite Channels are a convenient feature that lets you quickly select channels of your choice without waiting for the TV to select all the in-between channels. To tune to a favorite channel, press the F A V (Favorite) button repeatedly. F WATCHING TV / CHANNEL CONTROL A Favorite 1 1 CH P A G E or 2 3 4 5 6 7 8 9 Select your desired channel. 0 2 Q.MENU 3 Select D e l / A d d / F a v. Select F a v o r i t e.
FAVORITE CHANNEL LIST Displaying the favorite channel list Favorite List DTV 2-1 DTV 3-1 DTV 4-1 1 MARK FAV Display the Favorite channel list. Selecting a channel in the favorite channel list 1 2 ENTER Switch to the chosen channel number. Paging through a favorite channel list 1 CH 2 P A G E Turn the pages. Return to TV viewing. EXIT WATCHING TV / CHANNEL CONTROL Exit Select a channel.
WATCHING TV / CHANNEL CONTROL BRIEF INFORMATION Brief Info shows the present screen information. 1 INFO Show the Brief Info on the screen. BACK Return to TV viewing. 2 WATCHING TV / CHANNEL CONTROL 7 1 2 3 4 5 6 Brief Info Title Test.. DOLBY DIGITAL CNN CC D 4:3 16:9 480i 480p 720p 1080i 1080p Sat, Feb 21, 2009 Multilingual 10:40 AM 10:10 AM D CC Caption 11:40 AM 1080i TV-PG D L S V Multilingual : The program contains two or more audio services. Use the Q .
INPUT LIST Only these input signals which are connected to a TV can be activated and selected. 1 INPUT Select the desired input source. ENTER ie) Disconnected inputs are inactive (grayed out) AV1 Component AV2 RGB-PC Input Label Exit Select a desired input source (except T V). Then, you can select your desired I n p u t L a b e l with using Blue button. G p .
WATCHING TV / CHANNEL CONTROL INPUT LABEL This indicates which device is connected to which input port. OPTION Move Enter Menu Language : English AV1 Audio Language : English AV2 F G Component Input Label WATCHING TV / CHANNEL CONTROL SIMPLINK : On RGB-PC Key Lock : Off HDMI1 Caption : Off Set ID :1 Demo Mode HDMI2 Close : Off E With using OPTION menu With using INPUT button 1 1 MENU Select O P T I O N. ENTER Select I n p u t L a b e l. ENTER Select the source.
AV MODE AV Mode toggles through preset Video and Audio settings. ■ Off Cinema ■ Game Sport 1 AV MODE ■ ■ 2 ■ ENTER ■ KEY LOCK The TV can be set up so that it can only be used with the remote control. This feature can be used to prevent unauthorized viewing by locking out the front panel controls. This TV is programmed to remember which option it was last set to even if you turn the TV off.
WATCHING TV / CHANNEL CONTROL SIMPLINK allows you to control and play other AV devices connected with HDMI cable without additional cables and settings. This TV may work with devices with HDMI-CEC support, but only devices with the logo are fully supported. SIMPLINK can be turned on and off in the user menus.
SIMPLINK Functions D i r e c t P l a y : After connecting AV devices to the TV, you can directly control the devices and play media without additional settings. ■ S e l e c t A V d e v i c e : Enables you to select one of the AV devices connected to TV. ■ D i s c p l a y b a c k : Control connected AV devices by pressing the , ENTER, G, A, l l, FF and GG buttons. ■ P o w e r o f f a l l d e v i c e s : When you power off the TV, all connected devices are turned off.
USB ENTRY MODES When you connect a USB device, this pop up menu is displayed automatically. When the Pop Up menu does not appear, you can select Photo List or Music List in the USB menu. In USB device, you can not add a new folder or delete the existing folder. 1 Connect the USB device to the U S B IN jacks on the side of TV. ■ This TV supports JPG and MP3 files. USB IN When removing the USB device Select the U S B D e v i c e menu before removing the USB device.
PHOTO LIST You can view .JPG files from USB storage devices. The On Screen Display on your model may be slightly different than what is pictured below. Supported photo file: *.JPG ■ ■ ■ You can play JPG files only. Only baseline scan is supported among JPG. Available JPG size (width x height, pixel): 64 x 64 - 15360 x 8640 USB Screen Components 2 1 MENU Select U S B.
USB Photo Selection and Popup Menu Photo List Page 2/3 Drive1 JMJ001 1366x768, 125KB Up Folder Navigation USB Drive1 JMJ001 03/30/2008 06/10/2008 KY104 06/19/2008 KY102 04/03/2008 KY105 01/31/2008 JMJ001 01/01/2000 JMJ005 05/13/2008 JMJ002 06/15/2008 JMJ006 05/26/2008 JMJ003 04/03/2008 JMJ007 02/18/2008 JMJ004 02/18/2008 JMJ008 02/18/2008 Page 2/3 CH Page Change Up Folder MARK Mark Exit No Marked Up Folder 1366x768, 125KB 1 KY103 KY101 Popup Menu Photo List Naviga
Full Screen Menu You can change the Photo List view so that it fills the screen. More operations are available in full screen mode.
USB 6 ENTER Select the Slideshow, B G M, D e l e t e, Option, or Hide. (Rotate), ■ 1/17 Slideshow BGM Delete Option Hide Use button to select the previous or next photo. ■ Use button to select and control the menu on the full-sized screen. USB S l i d e s h o w: Selected photos are displayed during the slide show. If no photo is selected, all photos in the current folder are displayed during slide show. ■ Set the time interval of the slide show in O p t i o n.
MUSIC LIST You can use the Music List menu to play MP3 files from a USB storage device. This TV cannot play back copy-protected files. The On Screen Display on your model may be slightly different. USB Supported music file: *.MP3 Bit rate range 32 Kbps - 320 Kbps • Sampling rate (Sampling Frequency) MPEG1 layer 3: 32 kHz, 44.1 kHz, 48 kHz MPEG2 layer 3: 16 kHz, 22.05 kHz, 24 kHz MPEG2.5 layer 3: 8 kHz, 11.025 kHz, 12 kHz Screen Components 1 2 MENU Select U S B. ENTER Select M u s i c L i s t.
USB Music Selection and Popup Menu P l a y (During stop): Play the selected music. Once a song finishes playing, the next selected one will be played. When there are no selected musics to play, the next one in the current folder will be played. If you go to a different folder and press the E N T E R button, the current music in playback will stop. G P l a y M a r k e d: Play the selected musics. Once a music finishes playing, the next selected one will be played automatically.
■ The play information box (as shown below) will automatically move across the screen when there is no user input to prevent a fixed image remaining on the screen for a extended period of time. USB ! NOTE G G G G When music is playing, is displayed in front of the music play time. A damaged or corrupted music file that does not play displays 00:00 as the play time. Music files with copy-protection will not play. Press E N T E R, A , B A C K, or E X I T button to stop the screen saver.
PICTURE CONTROL PICTURE SIZE (ASPECT RATIO) CONTROL This feature lets you choose the way an analog picture with a 4:3 aspect ratio is displayed on your TV. You can select a different aspect ratio depending on input source (analog broadcasting, digital broadcasting, aux).
4:3 Adjust the picture horizontally, in a linear proportion to fill the entire screen. Choose 4:3 when you want to view a picture with an original 4:3 aspect ratio. Just Scan Zoom Normally the edges of video signals are cropped 1-2%. Just Scan turns off this cropping and shows the complete video. Notes: If there is noise on the edges of the original signal, it will be visible when Just Scan is activated.
PICTURE CONTROL PICTURE WIZARD PICTURE Move White Level Set the screen above identical to the Recommended sample below. Recommended • Contrast 90 Previous Enter Next 5 Aspect Ratio : 16:9 Picture Wizard ENTER Adjust W h i t e L e v e l. Energy Saving : Off Picture Mode High E Low E This feature lets you adjust the picture quality of the original image. Use this to calibrate the screen quality by adjusting the Black and White Level etc.
Vertical Sharpness Backlight Recommended Dark • Backlight Previous Next 9 ENTER Recommended 50 Bright E 50 E • V Sharpness High E Low Set the Backlight to your Brightness preference. E Set the screen above identical to the Recommended sample below. Previous Next 13 Adjust V e r t i c a l S h a r p n e s s. Adjust B a c k l i g h t. ENTER Color Temperature Complete Set the Color Temperature as you like. Refer to the samples below. Select (an) input(s) to apply the settings.
PICTURE CONTROL PRESET PICTURE SETTINGS (PICTURE MODE) There are factory presets for picture settings available in the user menus. You can use a preset, change each setting manually.
MANUAL PICTURE ADJUSTMENT - USER MODE Adjust the picture appearance to suit your preference and viewing situations. PICTURE Move Aspect Ratio Enter : 16:9 Picture Wizard 70 • Contrast 90 • Brightness 50 • Sharpness 70 70 E E • Backlight : Standard • Backlight E E Energy Saving : Off Picture Mode Enter E MENU Select P I C T U R E. ■ ■ 2 ENTER 3 ENTER 4 ENTER Select P i c t u r e M o d e. Select V i v i d, S t a n d a r d, N a t u r a l, C i n e m a, S p o r t, or G a m e.
PICTURE CONTROL PICTURE IMPROVEMENT TECHNOLOGY You can calibrate the screen for each Picture Mode or set the video value according to the special video screen. You can set the video seeing differently for each input. To reset to the factory default after making adjustments to each input source, execute the P i c t u r e R e s e t function for each P i c t u r e M o d e.
EXPERT PICTURE CONTROL By segmenting categories, E x p e r t 1 and E x p e r t 2 provide more categories which users can set as they see fit, offering the optimal picture quality for users. This may also be used by a professional to help optimize the TV performance in the environment the TV is in.
PICTURE CONTROL Color Temperature (Advanced Control) Dynamic Contrast ■ Set to warm to enhance hotter colors such as red, or set to cool to make picture bluish. ■ Adjusts the contrast to keep it at the best level according to the brightness of the screen. The picture is improved by making bright parts brighter and dark parts darker. ■ Adjusts screen colors so that they look livelier, richer and clearer.
Color Gamut Edge Enhancer Color Standard Color Filter xvYCC ■ Show clearer and distinctive yet natural edges in of the video. P i c t u r e M o d e - C i n e m a, E x p e r t". This function is enabled in "P ■ Choose between SD color and HD color depending on Input Source. ■ ■ This is the function to filter the specific colors of the video. You can use the RGB filter to set color saturation and hue accurately. *This feature is not available for all models.
PICTURE CONTROL ENERGY SAVING It reduces the TV’s power consumption by lowering the backlight level. The default factory setting complies with the E n e r g y S t a r requirements and is adjusted to the comfortable level to be viewed at home. You can increase the brightness of your screen by adjusting the E n e r g y S a v i n g level or by setting the P i c t u r e M o d e.
PICTURE RESET Settings of the selected picture modes return to the default factory settings. PICTURE Move PICTURE Enter Move Enter E E • Contrast 50 • Contrast • Brightness 50 • Brightness 50 • Sharpness 50 settings will be resetted. ? All picture Continue? • Color 50 • Sharpness 50 • Color 50 • Tint • Tint 0 R G 0 R i Resetting video configuration... • Advanced Control G Yes • Advanced Control No • Picture Reset Screen (RGB-PC) MENU Select P I C T U R E.
PICTURE CONTROL DEMO MODE Displays a slide show to explain the various feature of this TV. OPTION Move Enter OPTION Move E E Audio Language : English Input Label Audio Language : English Input Label SIMPLINK : On SIMPLINK Key Lock : Off Key Lock : Off Caption : Off Caption : Off Set ID :1 Set ID :1 Demo Mode : Off Demo Mode : On Initial Setting : Store Demo Initial Setting On : Store Demo : On Off PICTURE CONTROL 1 MENU Select O P T I O N.
SOUND & LANGUAGE CONTROL AUTO VOLUME LEVELER (AUTO VOLUME) Auto Volume makes sure that the volume level remains consistent whether you are watching a commercial or a regular TV program. Because each broadcasting station has its own signal conditions, volume adjustment may be needed every time the channel is changed. This feature allows users to enjoy stable volume levels by making automatic adjustments for each program.
CLEAR VOICE II By differentiating the human sound range from others, it improves the sound quality of voices. AUDIO Move Auto Volume : Off Clear Voice II : Off • Level Balance Sound Mode Enter 3 - + 0 L R : Standard Clear Voice II : On Balance 3 - 0 L : Standard • Infinite Sound :Off 50 • Treble 50 • Bass 50 • Bass 50 MENU Select A U D I O. ENTER Select C l e a r V o i c e I I. SOUND & LANGUAGE CONTROL 3 Select O n or O f f.
PRESET SOUND SETTINGS (SOUND MODE) Sound Mode lets you enjoy the best sound without any special adjustment as the TV sets the appropriate sound options based on the program content. AUDIO Move Enter AUDIO Auto Volume : Off Auto Volume : Off Clear Voice II : Off Clear Voice II : Off • Level Balance Sound Mode 3 - + 0 L R : Standard • Level Balance Sound Mode 50 • Treble 50 50 • Bass 50 ■ ■ BACK Return to the previous menu.
SOUND & LANGUAGE CONTROL SOUND SETTING ADJUSTMENT - USER MODE Adjust the sound to suit your taste and room situations. Move Auto Volume : Off Clear Voice II : Off • Level Balance Sound Mode Enter 3 - + 0 L R : Standard • Level Balance 3 - 0 L • Infinite Sound :Off • Treble 50 • Bass 50 • Bass 50 Select S o u n d M o d e. Select S t a n d a r d, M u s i c, C i n e m a, S p o r t, or G a m e. 4 ENTER Select T r e b l e or B a s s. ENTER Make appropriate adjustments.
INFINITE SOUND Select this option to sound realistic. Move Auto Volume : Off Clear Voice II : Off • Level Balance 3 - + 0 L R : Standard AUDIO : Off Clear Voice II : Off • Level Balance Sound Mode MENU 3 - 0 L • Infinite Sound :Off • Treble 50 • Treble 50 • Bass 50 • Bass 50 E Enter + R • Infinite Sound : Standard • Infinite Sound :Off E 1 Move Auto Volume • Treble 50 • Bass 50 E Sound Mode Enter Off E AUDIO Close Select A U D I O.
SOUND & LANGUAGE CONTROL BALANCE Adjust the left/right sound of speaker to suit your taste and room situations. Move AUDIO Enter Move Auto Volume : Off Auto Volume : Off Clear Voice II : Off Clear Voice II : Off • Level Sound Mode 3 - + 0 L R • Level Balance : Standard Sound Mode - + L Balance R 0 : Standard • Infinite Sound :Off • Infinite Sound :Off • Treble 50 • Treble 50 • Bass 50 • Bass 50 E Close E 4 1 MENU Select A U D I O.
TV SPEAKERS ON/OFF SETUP Turn the TV speakers off if using external audio equipment. AUDIO Move Enter AUDIO E 0 L R Balance Sound Mode : Standard • Infinite Sound :Off 50 • Treble 50 • Bass 50 • Bass 50 : On MENU Select A U D I O. ENTER Select T V S p e a k e r. 3 Select O n or O f f. 4 BACK Return to the previous menu. EXIT Return to TV viewing.
SOUND & LANGUAGE CONTROL EXTERNAL SPEAKERS ON/OFF SETUP Turn the external speakers on if using external audio equipment. AUDIO Move Enter AUDIO E Sound Mode 0 L R Balance Sound Mode : Standard • Infinite Sound :Off 50 • Treble 50 • Bass 50 • Bass 50 : On SOUND & LANGUAGE CONTROL 80 1 MENU Select A U D I O. ENTER Select E x t e r n a l S p e a k e r. 3 ENTER L • Treble External Speaker : Off 2 0 Select O n or O f f. 4 BACK Return to the previous menu.
STEREO/SAP BROADCAST SETUP For Analog only: This TV can receive MTS stereo programs and any SAP (Secondary Audio Program) that accompanies the stereo program if the station transmits an additional sound signal. Mono sound is automatically used if the broadcast is only in Mono. F Multi Audio G English A 1 Q.MENU 2 Digital TV Select S A P. Select M o n o, S t e r e o, or S A P. 3 1 Q.MENU 2 Select M u l t i A u d i o. Select other languages. 3 EXIT Return to TV viewing.
SOUND & LANGUAGE CONTROL AUDIO LANGUAGE Other languages may be available if a digital signal is provided by the broadcasting station. This feature operates only in DTV/CADTV mode.
ON-SCREEN MENUS LANGUAGE SELECTION The menus can be shown on the screen in the selected language. OPTION Move Enter : English Audio Language : English Audio Language English : English Español Input Label SIMPLINK : On SIMPLINK : On Key Lock : Off Key Lock : Off Caption : Off Caption : Off Set ID :1 Set ID :1 Demo Mode : Off Demo Mode : Off MENU Select O P T I O N. ENTER Select M e n u L a n g u a g e. Select your desired language.
SOUND & LANGUAGE CONTROL CAPTION MODE Analog Broadcasting System Captions Captions are provided to help people with hearing loss watch TV. Select a caption mode for displaying captioning information if provided on a program. Analog caption displays information at any position on the screen and is usually the program's dialog. Caption/Text, if provided by the broadcaster, would be available for both digital and analog channels on the Antenna/Cable.
Digital Broadcasting System Captions Choose the language you want the DTV/CADTV Captions to appear in. Other Languages can be chosen for digital sources only if they are included on the program. This function in only available when Caption Mode is set On.
SOUND & LANGUAGE CONTROL Caption Option Customize the DTV/CADTV captions that appear on your screen. This function in only available when Caption Mode is set On.
TIME SETTING CLOCK SETTING Auto Clock Setup The time is set automatically from a digital channel signal. The digital channel signal includes information for the current time provided by the broadcasting station. Set the clock manually if the current time is set incorrectly by the auto clock function.
TIME SETTING Manual Clock Setup If the current time setting is wrong, reset the clock manually. TIME Move Enter Clock TIME Move Clock Off Time : Off Off Time Enter F : Off Manual Month On Time : Off On Time : Off Sleep Timer : Off Sleep Timer : Off Date 02 21 Year 2009 Hour 10 AM Minute 10 Eastern Time Zone Daylight Saving Auto Close 1 TIME SETTING MENU Select T I M E. ENTER Select C l o c k. ENTER Select M a n u a l.
AUTO ON/OFF TIME SETTING This function operates only if the current time has been set. The O f f T i m e function overrides the O n T i m e function if they are both set to the same time. The TV must be in standby mode for the O n T i m e to work. If you do not press any button within 2 hours after the TV turns on with the O n T i m e function, the TV will automatically revert to standby mode. TIME Move TIME Enter Clock Move Enter Feb.
TIME SETTING SLEEP TIMER SETTING The Sleep Time turns the TV off at the preset time. Note that this setting is cleared when the TV is turned off. TIME Move Enter Clock TIME Move Enter Clock Off Time : Off Off Time : Off Off On Time : Off On Time : Off 10 min. Sleep Timer : Off Sleep Timer : Off 20 min. 30 min. 60 min. 90 min. 120 min. 180 min. 240 min. 1 MENU Select T I M E. ENTER Select S l e e p T i m e r. ENTER Make appropriate adjustments.
PARENTAL CONTROL / RATINGS Parental Control can be used to block specific channels, ratings and other viewing sources. The Parental Control Function (V-Chip) is used to block program viewing based on the ratings sent by the broadcasting station. The default setting is to allow all programs to be viewed. Viewing can be blocked by choosing the type of the program and the categories. It is also possible to block all program viewing for a time period. To use this function, the following must be done : 1.
PARENTAL CONTROL / RATINGS Lock System Enables or disables the blocking scheme you set up previously. LOCK Move Lock System Enter : Off LOCK Move Lock System : On Set Password Set Password Block Channel Block Channel Movie Rating Movie Rating TV Rating-Children TV Rating-Children TV Rating-General TV Rating-General Downloadable Rating Downloadable Rating Input Block Input Block Enter Off On 1 MENU 2 1 2 3 4 5 6 7 8 9 ENTER Select L O C K. Input the password.
Set Password Change the password by inputting a new password twice. LOCK Move Lock System Enter : Off LOCK Lock System Move Enter : Off Set Password Set Password Block Channel Block Channel Movie Rating Movie Rating TV Rating-Children TV Rating-Children TV Rating-General TV Rating-General Downloadable Rating Downloadable Rating Input Block Input Block New * * * * Confirm * * * * Close 1 ENTER MENU 2 1 2 3 4 5 6 7 8 9 Select L O C K. Input the password.
PARENTAL CONTROL / RATINGS CHANNEL BLOCKING Blocks any channels that you do not want to watch or that you do not want your children to watch. LOCK Move Lock System Enter : Off Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General Downloadable Rating Input Block Ch. Change Navigation CH Page Change Previous Block/Unblock 1 MENU ENTER Select L O C K. ■ 2 1 2 3 4 5 6 7 8 9 Input the password. 0 3 PARENTAL CONTROL / RATING 94 Select B l o c k C h a n n e l.
MOVIE & TV RATING Movie Rating (MPAA) - For USA Blocks movies according to the movie ratings limits specified, so children cannot view certain movies. You can set the ratings limit by blocking out all the movies with the ratings above a specified level. Keep in mind that the movie ratings limit only applies to movies shown on TV, not TV programs, such as soap operas.
PARENTAL CONTROL / RATINGS TV Rating Children - For USA Prevents children from watching certain children's TV programs, according to the ratings limit set. The children rating does not apply to other TV programs. Unless you block certain TV programs intended for mature audiences in the TV Rating - sub menu, your children can view those programs.
TV Rating General - For USA Based on the ratings, blocks certain TV programs that you and your family do not want to view.
PARENTAL CONTROL / RATINGS TV Rating English - For CANADA Selecting Canadian English rating system.
TV Rating French - For CANADA Selecting Canadian French rating system.
PARENTAL CONTROL / RATINGS DOWNLOADABLE RATING This function is available only for digital channels. This function operates only when TV has received Region5 Rating data.
EXTERNAL INPUT BLOCKING Enables you to block an input. LOCK Move Lock System Enter : Off AV1 Set Password AV2 Block Channel Component Movie Rating RGB-PC TV Rating-Children TV Rating-General Downloadable Rating F On G HDMI1 HDMI2 Close Input Block 1 MENU 2 1 2 3 4 5 6 7 8 9 ENTER Select L O C K. Input the password. 0 Select I n p u t B l o c k. 4 ENTER 5 Select input source. Select O n or O f f. 6 BACK Return to the previous menu. EXIT Return to TV viewing.
APPENDIX TROUBLESHOOTING Abnormal Operation Check to see if there is any object between the product and the remote control causing obstruction. Ensure you are pointing the remote control directly at the TV. ■ Ensure that the batteries are installed with correct polarity (+ to +, - to -). ■ Ensure that the correct remote operating mode is set: TV, VCR etc. ■ Install new batteries. ■ The remote control doesn’t work *This feature is not available for all models.
Audio Problems Press the VOL or VOLUME button. ■ Sound muted? Press MUTE button. ■ Try another channel. The problem may be with the broadcast. ■ Are the audio cables installed properly? ■ Picture OK & No sound No output from one of the speakers ■ Adjust Balance in menu option. ■ A change in ambient humidity or temperature may result in an unusual noise when the product is turned on or off and does not indicate a fault with the product.
APPENDIX MAINTENANCE Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you can enjoy your new TV. Caution: Be sure to turn the power off and unplug the power cord before you begin any cleaning. Cleaning the Screen Here’s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and then use it to wipe the screen.
IR CODES Custom Code: 04 / Comlement of Custom Code: FB (Hexa) Code Function Note 08 POWER Remote Control Button (Power On/Off) B0 G Remote Control Button 45 Q.
APPENDIX EXTERNAL CONTROL THROUGH RS-232C The RS-232C port allows you connect the RS-232C input jack to an external control device (such as a computer or an A/V control system) to control the TV’s functions externally. ■ Note: RS-232C on this unit is intended to be used with third party RS-232C control hardware and software. The instructions below are provided to help with programming software or to test functionality using telenet software. RS-232C Setup i.
RS-232C Configurations Either cable below can be used. 7-Wire Configuration (Serial female-female NULL modem cable) RXD TXD GND DTR DSR RTS CTS PC TV 2 3 5 4 6 7 8 3 2 5 6 4 8 7 D-Sub 9 D-Sub 9 TXD RXD GND DSR DTR CTS RTS 3-Wire Configurations (Not standard) PC TV 2 3 5 4 6 7 8 3 2 5 6 4 7 8 D-Sub 9 D-Sub 9 RXD TXD GND DTR DSR RTS CTS TXD RXD GND DTR DSR RTS CTS Set ID Use this function to specify a TV ID number. Refer to ‘Real Data Mapping’.
APPENDIX Command Reference List COMMAND1 COMMAND2 01. Power 02. Input Select 03. Aspect Ratio 04. Screen Mute 05. Volume Mute 06. Volume Control 07. Contrast 08. Brightness 09. Color 10. Tint 11. Sharpness 12. OSD Select 13. Remote Control Lock Mode k x k k k k k k k k k k a b c d e f g h i j k l 00 ~ 01 (G p.109) (G p.109) (G p.109) 00 ~ 01 00 ~ 64 00 ~ 64 00 ~ 64 00 ~ 64 00 ~ 64 00 ~ 64 00 ~ 01 k m 00 ~ 01 COMMAND1 COMMAND2 20. Channel Tuning DATA (Hexadecimal) m a COMMAND1 COMMAND2 14.
01. Power (Command: k a) To control Power On/Off of the TV. You can also adjust mute using the MUTE button on remote control.
APPENDIX 11. Sharpness (Command: k k) *Refer to ‘Real data mapping’. Acknowledgement [t][ ][Set ID][ ][OK/NG][Data][x] To adjust screen sharpness. You can also adjust sharpness in the PICTURE menu. Transmission [k][k][ ][Set ID][ ][Data][Cr] 17. Color Temperature (Command: k u) Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code) To adjust color temperature. *Refer to ‘Real data mapping’. You can also adjust color temperature in the PICTURE menu.
Data5: 7 Main/Sub Picture 6 Two/One Part Channel 5 Using Physical Channel 4 3 2 1 0 Step NTSC Air NTSC Cable ATSC Air ATSC Cable_std ATSC Cable_hrc ATSC Cable_irc ATSC cable_auto Reserved ... Reserved Reserved 0 Main 0 Two 0 Use x 0 0 0 0 1 Sub 1 One 1 No Use x 0 0 0 1 x 0 0 1 0 x 0 0 1 1 x 0 1 0 0 x 0 1 0 1 x 0 1 1 0 x 0 1 1 1 x x x x x x 1 1 1 1 The table above lists the binary code which must be converted to Hexadecimal before sending.
APPENDIX OPEN SOURCE LICENSE - This feature is not available for all models. GNU GENERAL PUBLIC LICENSE Version 2, June 1991 Copyright (C) 1989, 1991 Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone's free use or not licensed at all.
b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part there of, to be licensed as a whole at no charge to all third parties under the terms of this license.
APPENDIX 7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this license, they do not excuse you from the conditions of this license.
END OF TERMS AND CONDITIONS How to apply these terms to your new programs If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to make it free software which everyone can redistribute and change under these terms. To do so, attach the following notices to the program.
APPENDIX GNU LESSER GENERAL PUBLIC LICENSE Version 2.1, February 1999 Copyright (C) 1991, 1999 Free Software Foundation, Inc. 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. [This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library Public License, version 2, hence the version number 2.1.
Although the Lesser General Public License is Less protective of the users' freedom, it does ensure that the user of a program that is linked with the Library has the freedom and the wherewithal to run that program using a modified version of the Library. each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this license and to the absence of any warranty; and distribute a copy of this license along with the Library.
APPENDIX 3. You may opt to apply the terms of the ordinary GNU General Public License instead of this License to a given copy of the Library. To do this, you must alter all the notices that refer to this License, so that they refer to the ordinary GNU General Public License, version 2, instead of to this License. (If a newer version than version 2 of the ordinary GNU General Public License has appeared, then you can specify that version instead if you wish.) Do not make any other change in these notices.
For an executable, the required form of the "work that uses the library" must include any data and utility programs needed for reproducing the executable from it. However, as a special exception, the materials to be distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable.
APPENDIX If the library does not specify a license version number, you may choose any version ever published by the Free Software Foundation. 14.If you wish to incorporate parts of the library into other free programs whose distribution conditions are incompatible with these, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this.
MOZILLA PUBLIC LICENSE Version 1.1 --------------code which is described in the source code notice required by exhibit as original code, and which, at the time of its release under this license is not already covered code governed by this license. 1.Definitions. 1.0.1. “Commercial use” means distribution or otherwise making the covered code available to a third party. 1.1. “Contributor” means each entity that creates or contributes to the creation of modifications. 1.2.
APPENDIX (c) the licenses granted in this section 2.1(a) and (b) are effective on the date Initial developer first distributes original code under the terms of this license. (d) Notwithstanding section 2.1(b) above, no patent license is granted: 1) for code that You delete from the original Code; 2) separate from the original code; or 3) for infringements caused by: i) the modification of the original code or ii) the combination of the original code with other software or devices. 2.2. APPENDIX 3.
3.5. 3.6. (c) Representations. contributor represents that, except as disclosed pursuant to section 3.4(a) above, contributor believes that contributor's modifications are contributor's original creation(s) and/or contributor has sufficient rights to grant the rights conveyed by this license. 3.7. Required notices. You must duplicate the notice in exhibit A in each file of the source code.
APPENDIX 7. DISCLAIMER OF WARRANTY. COVERED CODE IS PROVIDED UNDER THIS LICENSE ON AN “AS IS” BASIS, WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, WARRANTIES THAT THE COVERED CODE IS FREE OF DEFECTS, MERCHANTABLE, FIT FOR A PARTICULAR PURPOSE OR NON-INFRINGING. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE COVERED CODE IS WITH YOU.
11. MISCELLANEOUS. This license represents the complete agreement concerning subject matter hereof. If any provision of this license is held to be unenforceable, such provision shall be reformed only to the extent necessary to make it enforceable. This License shall be governed by California law provisions (except to the extent applicable law, if any, provides otherwise), excluding its conflict-of-law provisions.
OWNER’S MANUAL LCD TV Please read this manual carefully before operating your set and retain it for future reference. 26LD360L 32LD360L The model and serial number of the TV is located on the back and one side of the TV. Record it below should you ever need service. 26LD350C 32LD350C MODEL SERIAL P/NO : SAC34026005 (1004-REV00) www.lg.
