OWNER’S MANUAL LED LCD TV Please read this manual carefully before operating your set and retain it for future reference. LT38** LT64** LT66** www.lg.
TABLE OF CONTENTS ENG ENGLISH TABLE OF CONTENTS 3 Licenses 3 OPEN SOURCE SOFTWARE NOTICE 4 Installation Procedure 4 ASSEMBLING AND PREPARING 4 7 8 9 9 11 12 14 14 Unpacking Parts and buttons Lifting and moving the TV Setting up the TV - Attaching the stand - Mounting on a table - Mounting on a wall - Tidying cables - How to use Dual Lock™ 15 MAKING CONNECTIONS 15 15 16 16 17 17 17 18 18 18 18 19 19 19 Connection of TV Antenna connection HDMI connection DVI to HDMI connection RGB-PC connectio
LICENSES / OPEN SOURCE SOFTWARE NOTICE 3 Supported licenses may differ by model. For more information about licenses, visit www.lg.com. Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a subsidiary of Rovi Corporation.
INSTALLATION PROCEDURE / ASSEMBLING AND PREPARING ENG ENGLISH NOTE Image shown may differ from your TV. yy Your TV’s OSD (On Screen Display) may differ slightly from that shown in this manual. yy The available menus and options may differ from the input source or product model that you are yy using. New features may be added to this TV in the future. yy The TV can be placed in standby mode in order to reduce the power consumption.
ASSEMBLING AND PREPARING 5 ENERGY AV MODE INPUT TV ENERGY AV MODE INPUT SAVING 2 3 4 5 6 7 8 9 0 FLASHBK LIST TV SAVING MARK FAV VOL 3D CH P A G E MUTE MENU INFO Q.MENU ENTER BACK EXIT L/R SELECT FREEZE RATIO Remote control, Batteries (AAA) (Only LT64**, LT66 **) (See p.20) Owner’s manual 2 3 4 5 6 7 8 9 0 FLASHBK LIST MARK FAV VOL 3D CH P A G E MUTE MENU INFO Q.
ASSEMBLING AND PREPARING ENG ENGLISH NOTE Antenna Isolator Installation Guide yy -- Use this to install TV in a place where there is a voltage difference between TV Set and GND of antenna signal. »» If there is a voltage difference between TV Set and GND of antenna signal, the antenna contact might be heated and excessive heat might cause an accident. -- You can improve the safety when watching TV by efficiently removing power voltage from TV antenna.
ASSEMBLING AND PREPARING ENGLISH ENG Parts and buttons 7 (Only 32/37/42/47LT64**, 32/37/42/47LT66**, 32/37/42/47LT38**) Screen (Only 22/26LT64**, 26LT66**, 22/26LT38** ) R IN 3 P Remote control sensor Speakers Power Indicator (Can be adjusted using the Power Indicator in the OPTION -menu.) Clock LED AV1 (RGB) Button ∨∧ Description Scrolls through the saved programmes. Adjusts the volume level. Turns the power on or off.
ASSEMBLING AND PREPARING ENG ENGLISH Lifting and moving the TV When moving or lifting the TV, read the following to prevent the TV from being scratched or damaged and for safe transportation regardless of its type and size. When transporting a large TV, there should yy be at least 2 people. When transporting the TV by hand, hold the yy TV as shown in the following illustration. CAUTION Avoid touching the screen at all times, as this yy may result in damage to the screen.
ASSEMBLING AND PREPARING 9 ENGLISH ENG Setting up the TV Put your TV on a pedestal stand and mount the TV on a table or wall.
ASSEMBLING AND PREPARING ENG ENGLISH (Only 32/37/42/47LT64**, 32/37/42/47LT66** 32/37/42/47LT38**) 1 3 M4 x 14 4 EA Stand Body M4X20 Front Stand Base Top View M4 x 14 2 4 EA CAUTION When attaching the stand to the TV yy set, place the screen facing down on a cushioned table or flat surface to protect the screen from scratches. Make sure that the screws are fastened yy completely. (If they are not fastened securely enough, the TV may tilt forward after being installed.
ASSEMBLING AND PREPARING Securing the TV to a table 1 Lift and tilt the TV into its upright position on a table. - Leave a 10 cm (minimum) space from the wall for proper ventilation. Fix the TV to a table to prevent from tilting forward, damage, and potential injury. Mount the TV on a table, and then insert and tighten the supplied screw on the rear of the stand. (Only 32/37/42/47LT64**, 32/37/42/47LT66**, 32/37/42/47LT38**) 10 cm 10 cm 10 cm 10 cm 2 Connect the power cord to a wall outlet.
ASSEMBLING AND PREPARING ENG ENGLISH Securing the TV to a wall (This feature is not available for all models.) Mounting on a wall Attach an optional wall mount bracket at the rear of the TV carefully and install the wall mount bracket on a solid wall perpendicular to the floor. When you attach the TV to other building materials, please contact qualified personnel. LG recommends that wall mounting be performed by a qualified professional installer.
ASSEMBLING AND PREPARING Separate purchase (Wall Mounting Bracket) Model 22/26LT64**, 22/26LT38**, 26LT66** 32LT64**, 32LT66**, 32LT38** VESA Standard screw Number of screws Wall mount bracket 100 x 100 M4 4 LSW100B(G) 200 x 100 M4 4 Model 37/42LT64**, 37/42LT66**, 37/42LT38** 37/42LT64**, 37/42LT66**, 37/42LT38** VESA Standard screw Number of screws Wall mount bracket 200 x 200 M6 4 LSW200BX(G) 200 x 200 M6 4 LSW220BX(G) Model 47LT64**, 47LT66**, 47LT38** 47LT64**, 47LT66**, 47LT38** VESA
ASSEMBLING AND PREPARING ENG ENGLISH How to use Dual Lock™ Tidying cables (Only 32/37/42/47LT64**, 32/37/42/47LT66**, 32/37/42/47LT38**) 1 Install the Power Cord Holder and Power Cord. It will help prevent the power cable from being removed by accident. (This feature is not available for all models.) Fix the set-top box to the TV and use it when you want to. 1 After removing the protection paper from the Dual Lock, stick it to the TV and the set-top box as shown.
MAKING CONNECTIONS This section on MAKING CONNECTIONS mainly uses diagrams for the 32LT66** models. Connect various external devices to the TV and switch input modes to select an external device. For more information on external device’s connection, refer to the manual provided with each device. Available external devices are: HD receivers, DVD players, VCRs, audio systems, USB storage devices, PC, gaming devices, and other external devices.
MAKING CONNECTIONS ENG ENGLISH HDMI connection DVI to HDMI connection Transmits the digital video and audio signals from your PC to the TV. Connect the PC and the TV with the HDMI cable as shown in the following illustrations. Choose any HDMI input port to connect. It does not matter which port you use. Transmits the digital video signal from an external device to the TV. Connect the external device and the TV with the DVI-HDMI cable as shown in the following illustrations.
MAKING CONNECTIONS 17 Component connection Transmits the video signal from PC to the TV. To transmit an audio signal, connect an audio cable. Transmits the analogue video and audio signals from an external device to the TV. Connect the external device and the ‑TV with the component cable as shown in the following illustrations.
MAKING CONNECTIONS Speaker output SETUP ENG ENGLISH Audio connection (Only 32/37/42/47LT64 SPEAKER **, 32/37/42/47LT66 **, 32/37/42/47LT38**OUT ) You may use an optional external audio system VOLUME instead of the built-in speaker. CONTROL Connect the external speaker to the Speaker output(STEREO) jack on the TV. UP DOWN Control port for Speaker out SPEAKER OUT NOTE If you use an optional external audio device yy instead of the built-in speaker, set the TV STEREO (8 ) speaker feature to off.
MAKING CONNECTIONS Euro Scart connection USB IN Connect a USB storage device such as a USB flash Transmits the video and audio signals from an memory, external hard drive, or a USB memory card external device to the TV set. Connect the external device and the TV set with the Euro Scart cable reader to the TV. as shown on the following illustration. To display images by using progressive scan, make sure to use the Euro Scart cable.
REMOTE CONTROL ENG ENGLISH REMOTE CONTROL The descriptions in this manual are based on the buttons on the remote control. Please read this manual carefully and use the TV correctly. To replace batteries, open the battery cover, replace batteries (1.5 V AAA) matching the and ends to the label inside the compartment, and close the battery cover. To remove the batteries, perform the installation actions in reverse. CAUTION Do not mix old and new batteries, as this may damage the remote control.
REMOTE CONTROL 21 ENGLISH ENG LT38** Number buttons Enters numbers. POWER Turns the TV on or off. ꕊ ENERGY SAVING Adjusts the brightness of the screen to reduce energy consumption. AV MODE Selects an AV mode. INPUT Changes the input source. TV/RAD Selects Radio, TV and DTV programme. GUIDE Shows programme guide. ENERGY AV MODE TV/ RAD 1 2 3 4 5 6 7 8 9 LIST 0 Q.VIEW RATIO GUIDE ALARM INFO OK FAV Accesses your favourite programme list. RATIO Resizes an image. MUTE Mutes all sounds.
MAINTENANCE / TROUBLESHOOTING ENG ENGLISH MAINTENANCE Cleaning your TV Clean your TV regularly to keep the best performance and to extend the product lifespan. CAUTION Make sure to turn the power off and disconnect the power cord and all other cables first. yy When the TV is left unattended and unused for a long time, disconnect the power cord from the wall yy outlet to prevent possible damage from lightning or power surges.
SPECIFICATIONS 23 Product specifications may be changed without prior notice due to upgrade of product functions. For the power supply and power consumption, refer to the label attached to the product. 22LT64** 22LT38** 22LT640H-ZA 22LT380C-ZA 517.0 x 386.0 x 192.0 517.0 x 386.0 x 192.0 517.0 x 332.0 x 41.6 517.0 x 332.0 x 41.6 With stand(kg) 3.7 3.7 Without stand(kg) 3.1 3.
SPECIFICATIONS ENG ENGLISH 42LT64** 42LT66** 42LT38** 42LT640H-ZA 42LT660H-ZA 42LT380C-ZA 992.0 x 667.0 x 273.0 992.0 x 667.0 x 273.0 992.0 x 667.0 x 273.0 992.0 x 604.0 x 55.0 992.0 x 604.0 x 55.0 992.0 x 604.0 x 55.0 With stand(kg) 15.5 15.5 15.5 Without stand(kg) 13.5 13.5 13.
SPECIFICATIONS Component port connecting information Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) 720x480 31.469 31.5 59.94 60 720x576 31.25 50 1280x720 37.5 44.96 45 50 59.94 60 1920x1080 33.72 33.75 28.125 26.97 27 33.716 33.75 56.25 67.43 67.5 59.94 60 50 23.97 24 29.976 30.00 50 59.94 60 RGB-PC, HDMI/DVI-PC supported mode Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) 720x400 31.468 70.08 640x480 31.469 59.94 800x600 37.879 60.
IR CODES ENG ENGLISH IR CODES This feature is not available for all models. yy Code (Hexa) 08 Function Note Remote control Button (Power On/Off) 95 (POWER) ENERGY SAVING 30 0B F0 10-19 53 1A AV MODE INPUT TV/RAD Number Key 0-9 LIST Q.
EXTERNAL CONTROL DEVICE SETUP 27 RS-232C Setup RS-232C Configurations Connect the RS-232C (serial port) input jack to an external control device (such as a computer or an A/V control system) to control the product’s functions externally. Connect the serial port of the control device to the RS-232C jack on the product back panel. Note: RS-232C connection cables are not supplied with the product. Set ID Set ID number. "Real Data Mapping". 1 Press Home to access the main menus.
EXTERNAL CONTROL DEVICE SETUP ENG ENGLISH Communication Parameters Stop bit: 1 bit yy Communication code: ASCII code yy Use a crossed (reverse) cable. yy Baud rate: 9600 bps (UART) yy Data length: 8 bits yy Parity : None yy Command reference list (Depending on model) 01. Power k 02. Aspect Ratio k 03. Screen Mute k a c d DATA (Hexadecimal) 00 to 01 (See p.30) (See p.30) 04. Volume Mute k e 00 to 01 05. Volume Control k f 00 to 64 06. Contrast k g 00 to 64 07.
EXTERNAL CONTROL DEVICE SETUP 29 Transmission [Command1][Command2][ ][Set ID][ ][Data][Cr] [Command 1] [Command 2] [Set ID] : First command to control the TV.(j, k, m or x) : Second command to control the TV. : You can adjust the set ID to choose desired monitor ID number in option menu. Adjustment range is 1 to 99. When selecting Set ID ‘0’, every connected set is controlled. Set ID is indicated as decimal (1 to 99) on menu and as Hexa decimal (0x0 to 0x63) on transmission/receiving protocol.
EXTERNAL CONTROL DEVICE SETUP ENG ENGLISH 01. Power (Command: k a) 04. Volume Mute (Command: k e) ►► To control Power On/Off of the set. ►► To control volume mute on/off. You can also adjust mute using the MUTE button on remote control. Transmission[k][a][ ][Set ID][ ][Data][Cr] Data 00 : Power Off 01 : Power On Ack [a][ ][Set ID][ ][OK/NG][Data][x] ►► To show Power On/Off.
EXTERNAL CONTROL DEVICE SETUP 13. Treble (Command: k r) ►► To adjust treble. You can also adjust treble in the AUDIO menu. Transmission [k][j][ ][Set ID][ ][Data][Cr] Data Red : 00 to Green : 64 * Refer to ‘Real data mapping’. See p.33. Transmission [k][r][ ][Set ID][ ][Data][Cr] Data Min : 00 to Max : 64 * Refer to ‘Real data mapping’. See p.33. Ack [j][ ][Set ID][ ][OK/NG][Data][x] Ack [r][ ][Set ID][ ][OK/NG][Data][x] 10. Sharpness (Command: k k) ►► To adjust the screen sharpness.
EXTERNAL CONTROL DEVICE SETUP ENG ENGLISH 17. Energy Saving (Command: j q) 19. Tune Command (Command: m a) ►► To reduce the power consumption of the TV. You can also adjust Energy Saving in PICTURE menu. ►► Select channel to following physical number.
EXTERNAL CONTROL DEVICE SETUP ENGLISH ENG 23. Input select (Command: x b) (Main Picture Input) ►► To select input source for main picture.
The model and serial numbers of the TV is located on the back of the TV Record it below should you ever need service.
