QUICK REFERENCE GUIDE LED LCD TV Please read this manual carefully before operating your set and retain it for future reference. 22LT560C 26LT560C 32LT560C 37LT560C 42LT560C 32LT560E 37LT560E 42LT560E 47LT560E P/NO : MFL67415402 (1204-REV03) www.lgsolutions.
LICENSES / OPEN SOURCE SOFTWARE NOTICE LICENSES Supported licenses may differ by model. For more information about licenses, visit www.lg.com. Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a subsidiary of Rovi Corporation.
IMPORTANT SAFETY INSTRUCTIONS 3 IMPORTANT SAFETY INSTRUCTIONS Always comply with the following precautions to avoid dangerous situations and ensure peak performance of your product. WARNING/CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. yy TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.
IMPORTANT SAFETY INSTRUCTIONS Protect the power cord from being walked on yy or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Only use attachments/accessories specified yy by the manufacturer. Use only with a cart, stand, tripod, bracket, yy or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
IMPORTANT SAFETY INSTRUCTIONS Warning - To reduce the risk of fire or yy electrical shock, do not expose this product to rain, moisture or other liquids. Do not touch the TV with wet hands. Do not install this product near flammable objects such as gasoline or candles, or expose the TV to direct air conditioning. Do not expose to dripping or splashing and yy do not place objects filled with liquids, such as vases, cups, etc. on or over the apparatus (e.g. on shelves above the unit).
IMPORTANT SAFETY INSTRUCTIONS If you smell smoke or other odors coming yy from the TV, unplug the power cord and contact an authorized service center. Do not press strongly upon the panel with a yy Supply hand or a sharp objectShort-circuit such as aPower nail, pencil Breaker or pen, or make a scratch on it. Keep the product away from direct sunlight. yy ENGLISH ENG Never touch this apparatus or antenna during yy a thunder or lightning storm.
TABLE OF CONTENTS 7 TABLE OF CONTENTS LICENSES 18 REMOTE CONTROL 2 OPEN SOURCE SOFTWARE NOTICE 20 GENERAL TROUBLESHOOTING 3 IMPORTANT SAFETY INSTRUCTIONS 20 CAUTION for using ezsign 2.
ASSEMBLING AND PREPARING INSTALLATION PROCEDURE 1 Open the package and make sure all the accessories are included. 2 Attach the stand to the TV set. 3 Connect an external device to the TV set. ASSEMBLING AND PREPARING Unpacking Check your product box for the following items. If there are any missing accessories, contact the local dealer where you purchased your product. The illustrations in this manual may differ from the actual product and item.
ASSEMBLING AND PREPARING 9 For LT560C series ENERGY AV MODE INPUT TV SAVING 1 2 3 4 5 6 7 8 9 LIST 0 FLASHBK MARK FAV VOL 3D CH P A G E MUTE MENU INFO Q.MENU ENTER BACK EXIT L/R SELECT FREEZE RATIO Quick Reference Guide Power Cord (For 32/37/42LT560C) (For 22LT560C) (For 26LT560C) Stand body/Stand base (See p.12) Stand body/Stand base (See p.13) Stand body/Stand base (See p.13) (For 32/37/42LT560C) (For 22LT560C) (For 26LT560C) Stand Screws 8 EA, M4 x 14 (See p.
ASSEMBLING AND PREPARING For LT560E series ENERGY AV MODE INPUT TV SAVING 1 2 4 5 7 8 9 0 FLASHBK LIST 3 6 MARK FAV VOL 3D CH P A G E MUTE MENU INFO Q.MENU ENTER BACK EXIT L/R SELECT FREEZE RATIO Quick Reference Guide EzSign 2.0 Editor CD Power Cord Stand body/Stand base (See p.12) Stand Screws 8 EA, M4 x 14 (See p.12) Desk-mount Screw 1 EA, M4 x 20 (See p.14) Protection cover Power Cord holder (See p.17) Cable holder (See p.
ASSEMBLING AND PREPARING 11 Parts and buttons Remote control Power indicator Side Connection panel HDMI input USB IN Buttons (For 22/26LT560C) IN 3 USB input Screen Buttons (For 32/37/42LT560C, 32/37/42/47LT560E) Speakers 1 2 R / DVI IN Rear Connection panel L RS-232C IN (CONTROL & SERVICE) EXTERNAL SPEAKER OUT ENG ENGLISH DC IN L/MONO -AUDIO- R (For 22/26LT560C) AV IN VIDEO RGB IN (PC) ANTENNA/ CABLE IN RJP INTERFACE AUDIO IN (RGB/DVI) Button Description ^ v Scrolls through th
ASSEMBLING AND PREPARING Setting up the TV Put your TV on a pedestal stand and mount the TV on a table or wall. Attaching the stand If you are not mounting the TV to a wall, use the following instructions to attach the stand. (For 32/37/42LT560C, 32/37/42/47LT560E) 1 4 EA 2 M4 x 14 Stand Body Front Stand Base Caution ENGLISH ENG When attaching the stand to the TV yy set, place the screen facing down on a cushioned table or flat surface to protect the screen from scratches.
ASSEMBLING AND PREPARING 13 (For 22/26LT560C) 1 2 4 EA M4 x 12 Stand Body M4X20 Front CAUTION Stand Base Top View When attaching the stand to the TV yy set, place the screen facing down on a cushioned table or flat surface to protect the screen from scratches. 3 M4 x 16 (For 22LT560C) 4 EA M4 x 12 (For 26LT560C) CAUTION Tighten the screws firmly to prevent the TV yy from tilting forward. Do not over tighten.
ASSEMBLING AND PREPARING Mounting on a table Adjusting the angle of the TV to suit view 1 Lift and tilt the TV into its upright position on a table. - Leave a 10 cm (4 inch) (minimum) space from the wall for proper ventilation. (Depending on model) Swivel 90±4 degrees to the left or right and adjust the angle of the TV to suit your view. 90 90 10 cm (4 inch ) 10 cm 10 cm 10 cm 2 Connect the power cord to a wall outlet.
ASSEMBLING AND PREPARING 15 Mounting on a wall Attaching the TV to a desk The TV should be attached to a desk so it cannot be pulled in a forward/backward direction, potentially causing injury or damaging the product. (For 32/37/42LT560C, 32/37/42/47LT560E) Attach an optional wall mount bracket at the rear of the TV carefully and install the wall mount bracket on a solid wall perpendicular to the floor. When you attach the TV to other building materials, please contact qualified personnel.
ASSEMBLING AND PREPARING Caution Disconnect the power first, and then move yy or install the TV. Otherwise electric shock may occur. If you install the TV on a ceiling or slanted yy wall, it may fall and result in severe injury. Use an authorized LG wall mount and contact the local dealer or qualified personnel. Do not over tighten the screws as this may yy cause damage to the TV and void your warranty. Only use screws and wall mounts that meet yy the VESA standard.
ASSEMBLING AND PREPARING Tidying cables 17 External speaker out For 32/37/42LT560C, 32/37/42/47LT560E Connect the external speaker. 1 Install the power cord holder and power cord. RGB IN (PC) / DVI IN 1 2 R EXTERNAL SPEAKER OUT L RS-232C IN (CONTROL & SERVICE) L/MONO -AUDIO- R DC IN AV IN VIDEO It will help prevent the power cable from being removed by accident.
REMOTE CONTROL REMOTE CONTROL The descriptions in this manual are based on the buttons on the remote control. Please read this manual carefully and use the TV correctly. To replace batteries, open the battery cover, replace batteries (1.5 V AAA) matching the and ends to the label inside the compartment, and close the battery cover. To remove the batteries, perform the installation actions in reverse. CAUTION Do not mix old and new batteries, as this may damage the remote control.
REMOTE CONTROL 19 VOL Adjusts the volume level. CC, CHAR/NUM CC: Selects a closed caption. CHAR/NUM: Switches between Letter and Number input modes. TIMER Turns the TV off in a set amount of time. Q.MENU BANK CH.PREVIEW TV 1 4 7 INPUT DVD .,;@ ghi pqrs 2 5 8 abc jkl tuv 0 MARK 3 6 9 ^ CH v, PAGE CH: Scrolls through the saved channels. PAGE: Moves to the previous or next screen. def mno PORTAL Displays and removes the interactive menu.
GENERAL TROUBLESHOOTING / CAUTION FOR USING EZSIGN 2.0 GENERAL TROUBLESHOOTING Display Panel Picture Symptom No picture. Possible Cause(s) Display panel is turned off. yy Antenna/cable not connected. yy Connections incorrect. yy MPI not connected yy Encrypted program. yy Wrong tuning band. yy Possible Solution(s) Turn TV ON. yy Power failure? yy Connect antenna/cable signal to TV. yy Check connections on TV. yy If applicable, connect MPI cable to MPI device. yy Try another channel.
SPECIFICATIONS 21 SPECIFICATIONS Product specifications may be changed without prior notice due to upgrade of product functions.
SPECIFICATIONS RGB(PC), HDMI (PC) supported mode Resolution Horizontal Vertical Frequency (KHz) Frequency (Hz) 720x400 31.469 70.08 640x480 31.469 59.94 800x600 37.879 60.31 1024x768 48.363 60.00 1360x768 47.712 60.015 1280x1024 63.981 60.020 1920x1080 67.5 60.00 HDMI (DTV) supported mode Resolution Horizontal Vertical Frequency (KHz) Frequency (Hz) ENGLISH ENG 720x480p 31.47 31.50 59.94 60.00 1280x720p 44.96 45.00 59.94 60.00 1920x1080i 33.72 33.75 59.94 60.
IR CODES 23 IR CODES (Depending on model) Code (Hexa) 08 Function POWER Note Code (Hexa) Function Note Remote control Button (Power On/Off) 0F TV Remote control Button DC 3D Remote control Button Q.
EXTERNAL CONTROL DEVICE SETUP EXTERNAL CONTROL DEVICE SETUP RS-232C Setup Connect the RS-232C (serial port) input jack to an external control device (such as a computer or an A/V control system) to control the product’s functions externally. Connect the serial port of the control device to the RS-232C jack on the product back panel. Type of connector; D-Sub 9-Pin Male 1 5 6 9 RS-232C IN (CONTROL & SERVICE) RS-232C IN (CONTROL & SERVICE) No.
EXTERNAL CONTROL DEVICE SETUP RS-232C configurations Set ID Set ID number. 7-Wire Configuration (Serial female-female NULL modem cable) OPTION 2 3 TXD TXD 3 2 RXD GND 5 5 GND DTR 4 6 DSR DSR 6 4 DTR RTS 7 8 CTS CTS 8 7 RTS • Set ID :1 • Mode Setting : Home Use ꔉ 1 Press Home or MENU to access the main menus. 2 Press the Navigation buttons to scroll to 3 Press the Navigation buttons to scroll to Set ID and press ENTER.
EXTERNAL CONTROL DEVICE SETUP Communication Parameters Stop bit: 1 bit yy Communication code: ASCII code yy Use a crossed (reverse) cable. yy Baud rate: 9600 bps (UART) yy Data length: 8 bits yy Parity : None yy Command reference list 01. Power COMMAND1 COMMAND2 DATA (Hexadecimal) k a 00 - 01 COMMAND1 COMMAND2 DATA (Hexadecimal) 14. Treble k r 00 - 64 ENGLISH ENG 02. Input Select x b (See p.28) 15. Bass k s 00 - 64 03. Aspect Ratio k c (See p.28) 16.
EXTERNAL CONTROL DEVICE SETUP 27 Transmission / Receiving protocol Transmission [Command1][Command2][ ][Set ID][ ][Data][Cr] [Command 1] : First command to control the set.(j, k, m or x) [Command 2] : Second command to control the set. [Set ID] : You can adjust the set ID to choose desired set ID number in Option menu. Adjustment range is 1~ 99. When selecting Set ID ‘0’, every connected the set is controlled.
EXTERNAL CONTROL DEVICE SETUP 01. Power (Command: k a) To control Power On/Off of the set. Transmission [k][a][ ][Set ID][ ][Data][Cr] Data 00: Power Off Data 01: Power On Acknowledgement [a][ ][Set ID][ ][OK/NG][Data][x] * In a like manner, if other functions transmit ‘FF’ data based on this format, Acknowledgement data feedback presents status about each function. * Note: In this model, set will send the Acknowledge after power on processing completion.
EXTERNAL CONTROL DEVICE SETUP 12. OSD Select (Command: k l) To select OSD (On Screen Display) on/off. Transmission [k][l][ ][Set ID][ ][Data][Cr] Data 00: OSD off Data 01: OSD on Acknowledgement [l][ ][Set ID][ ][OK/NG][Data][x] 13. Remote Control Lock Mode (Command: k m) To lock the remote control and the front panel controls on the set.
EXTERNAL CONTROL DEVICE SETUP 20. Energy Saving (Command: j q) To control the energy saving function. Transmission [ j ][q][ ][Set ID][ ][Data][Cr] Data 00: off 01: Minimum 02: Medium 03: Maximum 04: Auto/Intelligent sensor (depending on model) 05: Screen off Acknowledgement [q][ ][Set ID][ ][OK/NG][Data][x] 21. Auto Configuration (Command: j u) To adjust picture position and minimize image shaking automatically. Auto configuration only works in RGB-PC mode.
EXTERNAL CONTROL DEVICE SETUP 31 * Table List (Channel Tuning) 7 Main/Sub Picture 6 Two/One Part Channel 5 Using Physical Channel 4 Reserved 3 2 1 0 Step 0 Main 0 Two 0 Use x 0 0 0 0 NTSC Air 1 Sub 1 One 1 No Use x 0 0 0 1 NTSC Cable x 0 0 1 0 ATSC Air x 0 0 1 1 ATSC Cable_std x 0 1 0 0 ATSC Cable_hrc x 0 1 0 1 ATSC Cable_irc x 0 1 1 0 ATSC cable_auto x 0 1 1 1 Reserved x x x x x ...
CHILD SAFETY: It Makes A Difference How and Where You Use Your Flat Panel Display Congratulations on your purchase! As you enjoy your new product, please keep these safety tips in mind: THE ISSUE yy The home theater entertainment experience is a growing trend and larger flat panel displays are popular purchases. However, flat panel displays are not always supported on the proper stands or installed according to the manufacturer’s recommendations.
The model and serial numbers of the TV are located on the back and/or one side of the TV. Record them below should you ever need service. MODEL SERIAL LG Customer Information Center For inquires or comments, visit www.lg.com or call: 1-888-865-3026 1-888-542-2623 USA, Commercial User CANADA Register your product Online! www.lg.com Pro:Centric is a trademark of LG Electronics U.S.A., Inc. Pro:Idiom is a registered trademark of Zenith Electronics LLC.