ENGLISH ITALIANO ESPAÑOL FRANCAIS DEUTSCH OWNER’S MANUAL AIR CONDITIONER Please read this manual carefully before operating your set and retain it for future reference. TYPE : Wireless Remote Controller Models : PQWRCDF0 PQWRHDF0 P/NO : 3828A20580F www.lge.
Wireless Remote Controller Ownerʼs & Installation Manual TABLE OF CONTENTS ■ Safety Precaution................................................................3~4 ■ Part Description ..................................................................5~6 ■ Operating Instruction..............................................................7 ■ Installation Instruction............................................................8 - Setting Address of Central Control...........................................
Safety Precautions • The installation requires expert skills, and it should be installed by the service center or other shops specialized in the installation and recognized by our company. • For all the problems arising after installation by someone who has no relevant qualifications, our company will not provide free service. • The following safety cautions are provided to prevent unexpected dangers or losses.
Safety Precautions Push the button at one time. There will be no operation if you Several buttons at one time. Do not drop or throw the remote Controller. Do not give any strong impact and Put your foot it. Do not use this at the moisture and Humidity places. Do not place the remote controller in a location exposed to direct sunlight Aim at the signal receptor on the wiress remote controller so as to operate Only' One Do not use this at heating and Firing conditions.
Part Description ENGLISH Part Description LCD Screen Slide door(Closed) Wireless Remote Controller Accessory Holder(1EA) Fixing Screw (2EA) Owner's / Installation Manual AAA(1.
Part Description Wireless Remote Controller PLASMA Button (OPTIONAL) Used to start or stop the plasma-purification function. JET COOL Button Speed cooling operates super high fan speed. OPERATION MODE SELECTION Button Used to select the operation mode.
Operating Instruction ENGLISH Operating Instruction How to insert the Batteries 1. Remove the battery cover by pulling it according to the arrow direction. 2. Insert new batteries making sure that the (+) and (-) of battery are installed correctly. 3. Reattach the cover by sliding it back into position. NOTE 1. Always use/replace both batteries of same type. 2. If the system is not to be used for a long time, remove the batteries to save their working life. 3.
Installation Instruction Installation Instructions Installer Setting - Setting Address of Central Control 1 With the MODE button pressed, press the RESET button. 2 By using the TEMPERATURE SETTING button, set the indoor unit address. - Setting range : 00 ~ FF Group No. Indoor Unit No. 3 After setting the address, press the ON/OFF button toward the indoor unit 1 time. 4 5 The indoor unit will display the set address to complete the address setting.
Installation Instruction CAUTION Installer setting mode is to set the detail function of the remote controller. If the installer setting mode is not set correctly, it can cause problems to the product, user injury or property damage. This must be set by an certificated installer, and any installation or change that is carried out by a non-certificated person should be responsible for the results. In this case, free service cannot be provided. 1 With the FAN SPEED button pressed, press the RESET button.
Installation Instruction Installer Setting - Installer Setting Code Table Installer Setting Code Table No.
Owner's Instruction ENGLISH Owner's Instruction Cooling Mode - Standard Operation 1 Press the ON/OFF button. The unit will respond with beep sound. 2 Press MODE button to select Cooling Mode. 3 Set the desired temperature by pressing TEMP button. Press ROOM TEMPERATURE CHECKING button to check the room temperature. When setting the desired temperature is higher than room temperature, cooling wind isnʼt blow out. To raise the temperature To lower the temperature ❈ Setting Temp.
Owner's Instruction Auto Operation Mode 1 Press the ON/OFF button. The unit will respond with beep sound. 2 Press MODE button to select Auto Operation Mode. 3 Set the desired temperature. The temperature and fan speed are automatically set by the electronic controls based on the actual room temperature. If you feel hot or cold, press TEMPERATURE SETTING buttons for more cooling or heating effect. You cannot switch the indoor fan speed.
Owner's Instruction This Function is only available on some products. 1 Press the ON/OFF button. The unit will respond with beep sound. 2 Press MODE button to select Auto Changeover Mode. 3 Set the desired room temperature. ❈ Setting Temp. Range in Auto Changeover Mode : 18~30°C (64~86°F) To raise the temperature To lower the temperature 4 You can select the fan speed in four stepss-low, medium, high and chaos. Each time the button is pressed, the fan speed mode is shifted.
Owner's Instruction Auto Changeover Mode - Setting the Mode Change Temperature This Function is to set the operating mode of the Auto Changeover Mode. 1 In Auto Changeover Mode, Press the ROOM TEMPERATURE CHECKING button for 3 seconds. The mode change temperature set before will be displayed. Press for 3 seconds. 2 Press the TEMPERATURE SETTING button to set desired Mode Change Temperature. (Default value is 2°C(4°F).) To raise the temperature To lower the temperature ❈ Mode Change Temp.
Owner's Instruction ENGLISH Dehumidification Mode 1 Press the ON/OFF button. The unit will respond with beep sound. 2 Press MODE button to select Dehumidification Mode. 3 Set the fan speed. You can select the fan speed in four steps - low, medium, high, or chaos. Each time the button is pressed, the fan speed mode is shifted.
Owner's Instruction Heating Mode This Function is only for H/P model. 1 Press the ON/OFF button. The unit will respond with beep sound. 2 Press MODE button to select Heating Mode. 3 Set the desired temperature by pressing TEMP button. Press ROOM TEMPERATURE CHECKING button to check the room temperature. When setting the desired temperature is lower than room temperature, heating wind isnʼt blow out. To raise the temperature To lower the temperature 4 ❈ Setting Temp.
Owner's Instruction ENGLISH Fan Mode 1 Press the ON/OFF button. The unit will respond with beep sound. 2 Press MODE button to select Fan Mode. 3 Set the fan speed again. You can select the fan speed in four steps–low, medium, high, or chaos. Each time the button is pressed, the fan speed mode is shifted. Natural Wind by the chaos Logic • For more fresh feeling than other fan speed, press the Indoor Fan Speed Selector and set to chaos mode.
Temperature Setting/Room Temperature checking Temperature Setting/Room Temperature checking We can simply adjust the desired temperature • Press the buttons to adjust the desired temperature : Increase 1˚C or 2˚F per one time pressing : Decrease 1˚C or 2˚F per one time pressing Room temp: Indicate the current room temperature Set temp: Indicate the temperature that user want to set The cooling mode doesn't work if desired temperature is higher than room temperature Please lower the desired t
Airflow Setting Up/Down Airflow Direction Control (Optional) The up/down airflow (Vertical Airflow) can be adjusted by using the remote controller. 1. Press the ON/OFF button to start the unit. 2. Press UP/DOWN AIRFLOW button and the louvers will swing up and down. Press the UP/DOWN AIRFLOW button again to set the vertical louver at the desired airflow direction.
Sub function Sub function Plasma Purification(Optional) 1 Press the ON/OFF button. The unit will respond with beep sound. 2 Press the PLASMA button. Plasma Purification will start when the button is pressed and stop when the button is pressed again. PLASMA Purification only If you press the PLASMA button, Plasma Purification operates. • Plasma filter is a technology developed by LG to get rid of microscopic contaminants in the intake air generating a plasma of high charge electrons.
Sub function The Smart Clean function can be used by setting to manual or automatic. Auto Smart Clean operation If the accumulated operation time of the product exceeds 30 hours, the Smart Clean automatically starts when the unit is turned off. 1. Press the FUNCTION SETTING button 2 times. Smart Clean symbol will blink. 2. Press the SET/CLEAR button to reserve or cancel the Smart Clean function. You can set/clear with out on or off. Manual Smart Clean operation 1.
Sub function LCD Luminosity Control (Optional) Press the LCD LUMINOSITY button. It is comfortable when you feel that the display of the unit too bright . Celsius/Fahrenheit Switching Press the °C/°F SWITCH button to change from Celsius to Fahrenheit or from Fahrenheit to Celsius. Whenever press TEMPERATURE SETTING button in Fahrenheit mode, the temperature will increase/drop 2°F. Electric heater (Optional) It can only be set during heating operation. 1 Press the FUNCTION SETTING button 3 times.
Sub function It is the function that can control 4 vane angles individually in the ceiling type 4Way cassette product group. 1 Press the FUNCTION SETTING button 3 times. (4 times during heating operation) Individual vane angle control symbol will blink. • If you press the SET/CLEAR button in that time, all vanes are set to standard angle. 2 Set each vane angle by pressing up/down/left/right direction keys. • Every time the button is pressed, corresponding vane angle and set values are displayed.
Timer Timer Setting the Current Time 3. Press the SET / CLEAR button. 1. Press the TIMER button for 3 seconds. 2. Press TIME SETTING buttons until the desired time is set. NOTE Check the indicator for A.M. and P.M. Timer Setting 1. Press the TIMER button to turn timer on or off. 3. Press the SET / CLEAR button. 2. Press TIME SETTING buttons until the desired time is set. NOTE Select one of the following 3 types of operation.