OWNER’S MANUAL LED TV * LG LED TV applies LCD screen with LED backlights. Please read this manual carefully before operating your set and retain it for future reference. LN54** LP36** LP63** www.lg.
TABLE OF CONTENTS ENG ENGLISH TABLE OF CONTENTS 23 REMOTE CONTROL 26 MAINTENANCE 2 TABLE OF CONTENTS 26 26 3 LICENSES 26 3 OPEN SOURCE SOFTWARE NOTICE 4 INSTALLATION PROCEDURE 4 ASSEMBLING AND PREPARING 4 7 8 9 10 10 11 13 14 15 Unpacking Separate purchase Parts and buttons Lifting and moving the TV Setting up the TV - Attaching the stand - Mounting on a table - Mounting on a wall - Tidying cables - How to use Dual Lock™ 16 MAKING CONNECTIONS 16 16 17 17 18 18 19 20 20 20 21 21 21 22 22
LICENSES / OPEN SOURCE SOFTWARE NOTICE 3 Supported licenses may differ by model. For more information about licenses, visit www.lg.com. Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories. The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
INSTALLATION PROCEDURE / ASSEMBLING AND PREPARING ENG ENGLISH NOTE Image shown may differ from your TV. yy Your TV’s OSD (On Screen Display) may differ slightly from that shown in this manual. yy The available menus and options may differ from the input source or product model that you are yy using. New features may be added to this TV in the future. yy The TV can be placed in standby mode in order to reduce the power consumption.
ASSEMBLING AND PREPARING 5 ENGLISH ENG Owner’s manual Remote control, batteries (AAA) (See p.23, 24, 25) Stand body (See p.10) Stand base (See p.10) Stand screws 7 EA, M4 x 14 (See p.10) Desk-mount screw (See p.11) Cable holder (Depending on model) (See p.14) Power cord (Depending on model) Protective bracket/bolt (See p.14) Dual Lock™ (Only 32/37/42LP63**) (See p.15) EzSign 2.0 Editor CD (Only 32/37/42/47LN549E) or Isolator (Depending on model) (See p.
ASSEMBLING AND PREPARING ENG ENGLISH NOTE Antenna Isolator Installation Guide yy -- Use this to install TV in a place where there is a voltage difference between TV Set and GND of antenna signal. »» If there is a voltage difference between TV Set and GND of antenna signal, the antenna contact might be heated and excessive heat might cause an accident. -- You can improve the safety when watching TV by efficiently removing power voltage from TV antenna.
ASSEMBLING AND PREPARING Separate purchase items can be changed or modified for quality improvement without any notification. Contact your dealer to buy these items. These devices only work with certain models.
ASSEMBLING AND PREPARING ENG ENGLISH Parts and buttons Screen OK SETTINGS INPUT Power indicator and Remote control sensor Buttons Speakers Button Description Scrolls through the saved programmes. H HAdjusts OK ꔉ the volume level. Selects the highlighted menu option or confirms an input. SETTINGS Accesses the main menu, or saves your input and exits the menus. INPUT Changes the input source. /I Turns the power on or off.
ASSEMBLING AND PREPARING 9 When moving or lifting the TV, read the following to prevent the TV from being scratched or damaged and for safe transportation regardless of its type and size. yy When transporting a large TV, there should be at least 2 people. yy When transporting the TV by hand, hold the TV as shown in the following illustration. CAUTION Avoid touching the screen at all times, as this yy may result in damage to the screen.
ASSEMBLING AND PREPARING ENG ENGLISH Setting up the TV 3 Image shown may differ from your TV. Attaching the stand 4 EA M4 x 14 3 EA M4 x 14 1 Stand Body Front Stand Base 2 CAUTION yy Make sure that the screws are inserted correctly and fastened securely. If they are not fastened securely enough, the TV may tilt forward after being installed. yy Do not use too much force and over tighten the screws; otherwise screw may be damaged and not tighten correctly.
ASSEMBLING AND PREPARING Securing the TV to a table 1 Lift and tilt the TV into its upright position on a table. - Leave a 10 cm (minimum) space from the wall for proper ventilation. Fix the TV to a table to prevent from tilting forward, damage, and potential injury. Mount the TV on a table, and then insert and tighten the supplied screw on the rear of the stand. 10 cm m 10 c 10 cm 10 cm 2 Connect the power cord to a wall outlet.
ASSEMBLING AND PREPARING ENG ENGLISH Adjusting the angle of the TV to suit view (This feature is not available for all models.) 32LN54**, 32LP36**, 32LP63** Swivel 15 degrees to the left or right and adjust the angle of the TV to suit your view. 15˚ Using the Kensington security system 15˚ The Kensington security system connector is located at the rear of the TV. For more information of installation and using, refer to the manual provided with the Kensington security system or visit http://www.
ASSEMBLING AND PREPARING (This feature is not available for all models.) Mounting on a wall Attach an optional wall mount bracket at the rear of the TV carefully and install the wall mount bracket on a solid wall perpendicular to the floor. When you attach the TV to other building materials, please contact qualified personnel. LG recommends that wall mounting be performed by a qualified professional installer.
ASSEMBLING AND PREPARING ENG ENGLISH CAUTION Disconnect the power first, and then move yy or install the TV. Otherwise electric shock may occur. If you install the TV on a ceiling or slanted yy wall, it may fall and result in severe injury. Use an authorized LG wall mount bracket and contact the local dealer or qualified personnel. Do not over tighten the screws as this may yy cause damage to the TV and void your warranty. Use the screws and wall mount bracket that yy meet the VESA standard.
ASSEMBLING AND PREPARING (Only 32/37/42LP63**) Fix the set-top box to the TV and use it when you want to. 1 After removing the protection paper from the Dual Lock, stick it to the TV and the set-top box as shown. Dual Lock™ 2 Attach the set-top box to the TV by pressing the Velcro strips together. NOTE Please make sure no foreign substances yy exist on the surface of the product, and then firmly attach the Dual Lock.
MAKING CONNECTIONS Connect the TV to a wall antenna socket with an RF cable (75 Ω). This section on MAKING CONNECTIONS mainly AV 1 2 uses diagrams for the 32/37/42LP36 (RGB) ** models. AUDIO IN COMPONENT OPTICAL (COMPONENT/RGB/DVI) AUDIO OUT IN Connect various external devices to the TV and switch input modes to select an external CLOCK SPEAKER OUT device’s device. For more information on external connection, refer to the manual provided with each device.
DVI to HDMI connection Transmits the digital video and audio signals from your PC to the TV. Connect the PC and the TV 2 with theAV HDMI cable as shown. Choose any HDMI (RGB) AUDIO IN OPTICAL input port to connect. It does not matter which port ONENT/RGB/DVI) AUDIO OUT you use. Transmits the digital video signal from an external device to the TV. Connect the external device and the TV with the DVI-HDMI cable as shown. To transmit an audio signal, connect an audio cable.
MAKING CONNECTIONS Component connection (Only 32/37/42/47LN54**, 32/37/42LP36**) Transmits the analogue video and audio signals from an external device to the TV. Connect the external device and the TV with the component cable as shown. PCMCIA CARD SLOT Transmits the video signal from PC to the TV. To transmit an audio signal, connect an audio cable.
MAKING CONNECTIONS Speaker output setup PCMCIA CARD SLOT Connect the external speaker to the SPEAKER OUT jack on the TV.
ENG ENGLISH USB connection Euro Scart connection Transmits the video and audio signals from an external device to the TV set. Connect the external device and the TV set with the euro scart cable as shown. Connect a USB storage device such as s USB flash memory, external hard drive or a USB memory card reader to the TV and access the My media menu to use various multimedia files.
PCMCIA CARD SLOT MAKING CONNECTIONS /DVI IN 2 AV SPEAKER Transmits the headphone signal from the TV to an external device. Connect the external device and the TV with the headphone as shown. IN 3 You may use an optional external audio system instead of the built-in speaker.
PCMCIA CARD SLOT MAKING CONNECTIONS Wireless network connection /DVI IN AV TV can be connected to wireless network This (RGB) via the Wireless Dongle port. After making the physical connection, the TV needs to be set up for network communication. Connect the wireless dongle to the Wireless Dongle port on the TV.
REMOTE CONTROL 23 The descriptions in this manual are based on the buttons on the remote control. Please read this manual carefully and use the TV correctly. To replace batteries, open the battery cover, replace batteries (1.5 V AAA) matching the and ends to the label inside the compartment, and close the battery cover. To remove the batteries, perform the installation actions in reverse. or CAUTION Do not mix old and new batteries, as this may damage the remote control.
REMOTE CONTROL ENG ENGLISH 32/37/42/47LN549E (POWER) Turns the TV on or off. ꕊ ENERGY SAVING Adjusts the brightness of the screen to reduce ENERGY AV MODE energy consumption. AV MODE Selects an AV mode. INPUT Changes the input source. TV/RAD Selects Radio, TV and DTV programme. INPUT TV/ RAD SAVING 1 2 3 4 5 6 7 8 9 LIST 0 Q.VIEW Number buttons Enters numbers. LIST Accesses the saved programme list. Q.VIEW Returns to the previously viewed programme.
REMOTE CONTROL 25 (POWER) Turns the TV on or off. ꕊ ENERGY SAVING Adjusts the brightness of the screen to reduce ENERGY AV MODE energy consumption. AV MODE Selects an AV mode. INPUT Changes the input source. TV/RAD Selects Radio, TV and DTV programme. INPUT TV/ RAD SAVING 1 2 3 4 5 6 7 8 9 LIST 0 Q.VIEW Number buttons Enters numbers. LIST Accesses the saved programme list. Q.VIEW Returns to the previously viewed programme.
MAINTENANCE / TROUBLESHOOTING ENG ENGLISH MAINTENANCE Cleaning your TV Clean your TV regularly to keep the best performance and to extend the product lifespan. CAUTION Make sure to turn the power off and disconnect the power cord and all other cables first. yy When the TV is left unattended and unused for a long time, disconnect the power cord from the wall yy outlet to prevent possible damage from lightning or power surges.
CAUTION FOR USING EZSIGN 2.0 27 Only 32/37/42/47LN549E Do not remove a USB drive while data is being copied. It can corrupt the data and EzSign may not work yy properly. While loading a USB device or dongle, your TV may function slower than normal. yy While EzSign contents is running, the movie with internal subtitles is not supported in USB mode. EzSign yy TV supports only external subtitles. (External Subtitle format: *.smi/*.srt/*.sub(MicroDVD, Subviewer 1.0/2.0)/*.ass/*.ssa/*.txt(TMPlayer)/*.
SPECIFICATIONS ENG ENGLISH SPECIFICATIONS Product specifications may be changed without prior notice due to upgrade of product functions. MODEL 32LN54** 37LN54** 32LN548C-ZA / 32LN549C-ZA 37LN548C-ZA / 37LN549C-ZA 32LN549E-ZA 37LN549E-ZA With stand (mm) 738 x 497 x 207 849 x 561 x 236 Without stand (mm) 738 x 449 x 79.0 849 x 512 x 79.0 With stand (kg) 7.0 9.1 Without stand (kg) 6.4 8.
SPECIFICATIONS Dimensions (W x H x D) 32LP63** 37LP63** 32LP630H-ZA / 32LP631H-ZA 37LP630H-ZA / 37LP631H-ZA 32LP632H-ZA 37LP632H-ZA With stand (mm) 738 x 497 x 207 849 x 561 x 236 Without stand (mm) 738 x 449 x 79.0 849 x 512 x 79.0 7.0 9.1 With stand (kg) Weight 6.4 8.
SPECIFICATIONS ENG ENGLISH RGB-PC, HDMI/DVI-PC supported mode (Only 32/37/42/47LN54**, 32/37/42LP36**) HDMI/DVI-DTV supported mode Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) 720x480 31.469 31.5 59.94 60 720x400 31.468 70.08 720x576 31.25 50 640x480 31.469 59.94 800x600 37.879 60.31 1280x720 37.5 44.96 45 50 59.94 60 1024x768 48.363 60.00 1280x720 45 60 1280x768 47.78 59.87 1360x768 47.
IR CODES 31 IR CODES Code (Hexa) Function 08 (POWER) Note Remote control Button (Power On/Off) 95 ENERGY SAVING Remote control Button 30 AV MODE Remote control Button 0B INPUT Remote control Button F0 TV/RAD Remote control Button 10-19 Number Key 0-9 Remote control Button 53 LIST Remote control Button 1A Q.
EXTERNAL CONTROL DEVICE SETUP RS-232C configurations Connect the RS-232C (serial port) input jack to an external control device (such as a computer or an A/V control system) to control the product’s functions externally. Connect the serial port of the control device to the RS-232C jack on the product back panel. Note: RS-232C connection cables are not supplied with the /DVI IN product.
EXTERNAL CONTROL DEVICE SETUP 33 yy Baud rate: 9600 bps (UART) yy Data length: 8 bits yy Parity : None ENGLISH ENG Communication parameters yy Stop bit: 1 bit yy Communication code: ASCII code yy Use a crossed (reverse) cable. Command reference list (Depending on model) 01. Power 02. Aspect Ratio 03. Screen Mute 04. Volume Mute 05. Volume Control k a DATA (Hexadecimal) 00 to 01 k c (See p.35) 14. Bass k s 00 to 64 k d (See p.35) 15.
EXTERNAL CONTROL DEVICE SETUP ENG ENGLISH Transmission / Receiving Protocol Transmission [Command1][Command2][ ][Set ID][ ][Data][Cr] [Command 1] [Command 2] [Set ID] : First command to control the TV.(j, k, m or x) : Second command to control the TV. : You can adjust the set ID to choose desired monitor ID number in option menu. Adjustment range is 1 to 99. When selecting Set ID ‘0’, every connected set is controlled.
EXTERNAL CONTROL DEVICE SETUP 35 04. Volume Mute (Command: k e) ►► To control Power On/Off of the set. ►► To control volume mute on/off. You can also adjust mute using the MUTE button on remote control. Transmission[k][a][ ][Set ID][ ][Data][Cr] Data 00 : Power Off 01 : Power On Ack [a][ ][Set ID][ ][OK/NG][Data][x] ►► To show Power On/Off.
EXTERNAL CONTROL DEVICE SETUP ENG ENGLISH 09. Tint (Command: k j) 13. Treble (Command: k r) ►► To adjust the screen tint. You can also adjust tint in the PICTURE menu. ►► To adjust treble. You can also adjust treble in the AUDIO menu. Transmission [k][j][ ][Set ID][ ][Data][Cr] Data Red : 00 to Green : 64 * Refer to ‘Real data mapping’. See p.38. Transmission [k][r][ ][Set ID][ ][Data][Cr] Data Min : 00 to Max : 64 * Refer to ‘Real data mapping’. See p.38.
EXTERNAL CONTROL DEVICE SETUP 19. Tune Command (Command: m a) ►► To reduce the power consumption of the TV. You can also adjust Energy Saving in PICTURE menu. ►► Select channel to following physical number.
EXTERNAL CONTROL DEVICE SETUP 23. Input select (Command: x b) ENG ENGLISH (Main Picture Input) ►► To select input source for main picture.
The model and serial numbers of the TV is located on the back of the TV Record it below should you ever need service.
