OWNER’S MANUAL PLASMA TV Please read this manual carefully before operating your set and retain it for future reference. 42PN4500 50PN4500 50PN5300 60PN5300 P/NO : MFL67701702 (1211-REV00) 50PN6500 60PN6500 www.lg.
IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS Always comply with the following precautions to avoid dangerous situations and ensure peak performance of your product. WARNING/CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. yyDo not use this apparatus near water. TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.
IMPORTANT SAFETY INSTRUCTIONS yyProtect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. yyOnly use attachments/accessories specified by the manufacturer. yyUse only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
IMPORTANT SAFETY INSTRUCTIONS yyGrounding (Except for devices which are not grounded.) Ensure that you connect the earth ground wire to prevent possible electric shock (i.e. a TV with a three-prong grounded AC plug must be connected to a three-prong grounded AC outlet). If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes.
IMPORTANT SAFETY INSTRUCTIONS yyDot Defect The Plasma or LCD panel is a high technology product with resolution of two million to six million pixels. In a very few cases, you could see fine dots on the screen while you’re viewing the TV. Those dots are deactivated pixels and do not affect the performance and reliability of the TV. yyGenerated Sound “Cracking” noise: A cracking noise that occurs when watching or turning off the TV is generated by plastic thermal contraction due to temperature and humidity.
LICENSES LICENSES Supported licenses may differ by model. For more information about licenses, visit 'www.lg.com'. Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
TABLE OF CONTENTS 7 TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS 6 LICENSES 7 TABLE OF CONTENTS 8 INSTALLATION PROCEdURE 8 ASSEMBLING AND PREPARING 8 10 11 11 12 12 14 15 16 Unpacking Parts and buttons Additional information of the manual Lifting and moving the TV Setting up the TV - Attaching the stand - Mounting on a table - Mounting on a wall - Tidying cables 17 MAKING CONNECTIONS 17 18 18 18 19 20 21 21 23 23 24 Connecting to an antenna or cable Connecting to a HD receiver, DVD Player
INSTALLATION PROCEDURE / ASSEMBLING AND PREPARING INSTALLATION PROCEdURE 1 Open the package and make sure all the accessories are included. 2 Attach the stand to the TV set. 3 Connect an external device to the TV set. ASSEMBLING AND PREPARING Unpacking Check your product box for the following items. If there are any missing accessories, contact the local dealer where you purchased your product. The illustrations in this manual may differ from the actual product and item.
ASSEMBLING AND PREPARING 9 Ferrite core (Depending on model) CAUTION yyDo not use any unapproved items to ensure the safety and product life span. yyAny damages or injuries by using unapproved items are not covered by the warranty. yySome models appear to have a thin film on the screen. It is actually part of the screen, do not remove it. 1U se the ferrite core to reduce the electromagnetic interference in the power cable. Wind the power cable on the ferrite core once.
ASSEMBLING AND PREPARING Parts and buttons Remote control sensor Power indicator Screen ENGLISH Buttons Speakers Button Description / Scrolls through the saved channels. / Adjusts the volume level. Selects the highlighted menu option or confirms an input. Accesses the main menus, or saves your input and exits the menus. Changes the input source. Turns the power on or off.
ASSEMBLING AND PREPARING Additional information of the manual Viewing the owner's manual The owner’s manual in PDF file format is supplied on the enclosed CD. Install the Adobe Acrobat Reader to view the owner’s manual on your PC. 1 Insert the supplied CD. The web page appears automatically. 2 Click Owner’s Manual on the web page. 3 View the owner’s manual.
ASSEMBLING AND PREPARING Setting up the TV Put your TV on a pedestal stand and mount the TV on a table or wall. Attaching the stand If you are not mounting the TV to a wall, use the following instructions to attach the stand. Caution When attaching the stand to the TV set, place the screen facing down on a cushioned table or flat surface to yy protect the screen from scratches. Make sure that the screws are fastened completely.
ASSEMBLING AND PREPARING 13 To detach the stand, For 50PN4500, 50PN5300, 50PN6500 1 4 EA M5 x 16 Protection cover 1 EA 1 M5 x 16 Note Remove the stand before installing the TV on a yy wall mount by performing the stand attachment in reverse. When installing the wall mounting bracket, yy use the Protection cover. This will protect the opening from accumulating dust and dirt.
ASSEMBLING AND PREPARING Mounting on a table 1 Securing the TV to a table Lift and tilt the TV into its upright position on a table. - Leave a 10 cm (4 inches) (minimum) space from the wall for proper ventilation. (For 42PN4500) Fix the TV to a table to prevent from tilting forward, damage, and potential injury. Mount the TV on a table, and then insert and tighten the supplied screw on the rear of the stand. 10 cm (4 inches) 10 cm 10 cm 10 cm 2 Connect the power cord to a wall outlet.
ASSEMBLING AND PREPARING Securing the TV to a wall (optional) (Depending on model) 15 Mounting on a wall Attach an optional wall mount bracket at the rear of the TV carefully and install the wall mount bracket on a solid wall perpendicular to the floor. When you attach the TV to other building materials, please contact qualified personnel. We recommend that you use an LG brand wall mount when mounting the TV to a wall.
ASSEMBLING AND PREPARING Caution yyDisconnect the power before moving or installing the TV. Otherwise electric shock may occur. yyIf you install the TV on a ceiling or slanted wall, it may fall and result in severe injury. Use an authorized LG wall mount and contact the local dealer or qualified personnel. yyDo not over tighten the screws as this may cause damage to the TV and void your warranty. yyUse only screws and wall mounts that meet the VESA standard.
MAKING CONNECTIONS 17 MAKING CONNECTIONS You can connect various external devices to the TV. Supported external devices are: HD receivers, DVD players, VCRs, audio systems, USB storage devices, PC, gaming devices, and other external devices. For more information on external device’s connection, refer to the manual provided with each device. NOTE yyIf you record a TV program on a DVD recorder or VCR, make sure to connect the TV signal input cable to the TV through a DVD recorder or VCR.
MAKING CONNECTIONS Connecting to a HD receiver, DVD Player or VCR Connect a HD receiver, DVD Player or VCR to the TV and select an appropriate input mode. HDMI Connection HDMI is the best way to connect a device. Transmits digital video and audio signals from an external device to the TV. Connect the external device and the TV with the HDMI cable as shown in the following illustration. NOTE yyUse the latest High Speed HDMI™ Cable that supports CEC (Customer Electronics Control) function.
MAKING CONNECTIONS 19 Component Connection Transmits the analog video and audio signals from an external device to the TV. Connect the external device and the TV with the component cable as shown in the following illustration. NOTE yyIf cables are installed incorrectly, it could cause the image to display in black and white or with distorted color. yyCheck to ensure each cable is matched with the corresponding color connection.
MAKING CONNECTIONS Composite Connection Transmits the analog video and audio signals from an external device to the TV. Connect the external device and the TV with the composite cable as shown in the following illustration. NOTE yyIf you have a mono VCR, connect the audio cable from the VCR to the AUDIO L/MONO jack of the TV.
MAKING CONNECTIONS 21 Connecting to a PC NOTE yyIt is recommended to use an HDMI connection for the best image quality. yyDepending on the graphics card, DOS mode may not work if a HDMI to DVI Cable is in use. yyIn PC mode, there may be noise associated with the resolution, vertical pattern, contrast or brightness. If noise is present, change the PC output to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the PICTURE menu until the picture is clear.
MAKING CONNECTIONS IN 1 (PC) Method B: DVI to HDMI Connection (*Not Provided) COMPONENT IN AUDIO IN (PC) Y VIDEO PB AV IN PR L/MONO AUDIO R L R RED WHITE ENGLISH (*Not Provided) $8',2 287 '9, 287 PC
MAKING CONNECTIONS 23 Connecting to an Audio System You can use an optional external audio system instead of the built-in speaker. NOTE yyIf you use an optional external audio device instead of the built-in speaker, set the TV speaker feature to off. Digital Optical Audio Connection Transmits the digital audio signal from the TV to an external device. Connect the external device and the TV with the optical audio cable as shown in the following illustration.
MAKING CONNECTIONS Connecting a USB Device USB IN Connect a USB storage device such as a USB flash memory, external hard drive, or a USB memory card reader to the TV and access the USB menu to use various multimedia files.
REMOTE CONTROL 25 REMOTE CONTROL The descriptions in this manual are based on the buttons on the remote control. Please read this manual carefully and use the TV correctly. To install batteries, open the battery cover, replace batteries (1.5 V AAA) matching the ends to the label inside the compartment, and close the battery cover. To remove the and batteries, perform the installation actions in reverse. Caution yyDo not mix old and new batteries, as this may damage the remote control.
REMOTE CONTROL VOL Adjusts the volume level. FAV Accesses your favorite channel list. Selects a menu or option. AUDIO Digital signal: Changes the audio language. Analog signal: Changes the MTS sound. MUTE Mutes all sounds. ^ CH v, PAGE CH: Scrolls through the saved channels. PAGE: Moves to the previous or next screen. PICTURE Changes the image mode. INFO Views the information of the current program and screen. SOUND Changes the sound mode. ENGLISH SETTINGS Accesses the main menu. Q.
WATCHING TV WATCHING TV 4 If you do not complete the Initial setting, it will yy appear whenever the TV turns on. Disconnect the power cord from the power yy outlet when you do not use the TV for a long period of time. When you turn the TV on for the first time, the Initial setting screen appears. Select a language and customize the basic settings. Connect the power cord to a power outlet. 2 In Standby mode, press the power button on the remote control to turn the TV on.
TROUBLESHOOTING TROUBLESHOOTING General Problem Solution Cannot control the TV with the remote control. yyCheck the remote control sensor on the product and try again. yyCheck if there is any obstacle between the product and the remote control. to ). yyCheck if the batteries are still working and properly installed ( to , No image display and no sound is produced. yyCheck if the product is turned on. yyCheck if the power cord is connected to a wall outlet.
TROUBLESHOOTING / EXTERNAL CONTROL DEVICE SETUP 29 Video Problem Solution An image displays in black and white or the color quality is poor. yyAdjust the color setting in the menu option. yyKeep a sufficient distance between this product and other electronic products. yyScroll to other channels. There may a problem with the broadcast. Horizontal or vertical bars appears or images blur yyCheck if there are local interferences such as an electrical appliance or power tool.
SPECIFICATIONS SPECIFICATIONS Product specifications may be changed without prior notice due to upgrade of product functions.
CHILD SAFETY: It Makes A Difference How and Where You Use Your Flat Panel Display Congratulations on your purchase! As you enjoy your new product, please keep these safety tips in mind: THE ISSUE yy The home theater entertainment experience is a growing trend and larger flat panel displays are popular purchases. However, flat panel displays are not always supported on the proper stands or installed according to the manufacturer’s recommendations.
The extended owner’s manuals that contain information on the advanced features of this LG TV are located on the CD-ROM provided in an electronic version. To read these files, you will need to use the personal computer (PC) equipped with a CD-ROM drive. The model and serial number of the TV is located on the back and/or one side of the TV. Record it below should you ever need service. MODEL SERIAL LG Customer Information Center For inquires or comments, visit www.lg.
OWNER’S MANUAL EXTERNAL CONTROL DEVICE SETUP Please read this manual carefully before operating the set and retain it for future reference. www.lg.
2 KEY CODES ENGLISH ENG KEY CODES • This feature is not available for all models. Code (Hexa) Function Note Code (Hexa) Function Note 00 CH +, PR + R/C Button 45 Q.
EXTERNAL CONTROL DEVICE SETUP 3 • Image shown may differ from your TV. Connect the USB to Serial converter/RS-232C input jack to an external control device (such as a computer or an A/V control system) to control the product’s functions externally. Note: The type of control port on the TV can be different between model series. * Please be advised that not all models support this type of connectivity. * Cable is not provided.
USB USB IN IN 4 EXTERNAL CONTROL DEVICE SETUP (PC) (PC) RS-232C IN (CONTROL & SERVICE) Phone jack Type RS-232C • You need to purchase the phone-jack to RS-232 cable required for theIN connection between the PC and (CONTROL & SERVICE) the TV, which is specified in the manual. (TV) (TV) (PC) (PC) * For other models, connect to the USB port.
EXTERNAL CONTROL DEVICE SETUP 5 • Baud rate : 9600 bps (UART) • Data length : 8 bits • Parity : None ENGLISH ENG Communication Parameters • Stop bit : 1 bit • Communication code : ASCII code • Use a crossed (reverse) cable. Command reference list (Depending on model) COMMAND1 COMMAND2 DATA (Hexadecimal) 01. Power off k a 00 02. Aspect Ratio k c (p.7) 03. Screen Mute k d (p.7) k e 00 to 01 k f 00 to 64 06. Contrast k g 00 to 64 07. Brightness k h 00 to 64 04. Volume Mute 05.
6 EXTERNAL CONTROL DEVICE SETUP ENGLISH ENG Transmission / Receiving Protocol Transmission [Command1][Command2][ ][Set ID][ ][Data][Cr] [Command 1] : First command to control the TV. (j, k, m or x) [Command 2] : Second command to control the TV. [Set ID] : You can adjust the [Set ID] to choose desired monitor ID number in option menu. Adjustment range in TV is 1 to 99. If [Set ID] value is selected to ‘0’, every connected set can be controlled.
EXTERNAL CONTROL DEVICE SETUP 7 01. Power (Command: k a) ►► To control Power Off of the set. Transmission[k][a][ ][Set ID][ ][Data][Cr] Data 00 : Power Off Ack [a][ ][Set ID][ ][OK/NG][Data][x] ►► To Show Power On. (Works TV is On Only) Transmission [k][a][ ][Set ID][ ][FF][Cr] Ack [a][ ][Set ID][ ][OK][01][x] * Similarly, if other functions transmit ‘FF’ data based on this format, Acknowledgement feedback presents status about each function. 02.
8 EXTERNAL CONTROL DEVICE SETUP ENGLISH ENG 09. Tint (Command: k j) 14. Color(Colour) Temperature (Command: x u) ►► To adjust the screen tint. You can also adjust tint in the PICTURE menu. ►► To adjust colour temperature. You can also adjust Color(Colour) Temperature in the PICTURE menu.
EXTERNAL CONTROL DEVICE SETUP [Data 00][Data 01]: Channel Data Data 00 : High Channel data Data 01 : Low Channel data - 00 00 ~ 27 0F (Decimal: 0 ~ 9999) Data 05: Input Source (Analogue) - 00 : Terrestrial TV (ATV) - 01 : Cable TV (CATV) * Digital Terrestrial/Cable Data 00 : xx (Don't care) Data 02 : Input Source (Digital) - 10 : Terrestrial TV (DTV) - 20 : Terrestrial Radio (Radio) - 40 : Satellite TV (SDTV) - 50 : Satellite Radio (S-Radio) - 90 : Cable TV (CADTV) - a0 : Cable Radio (CA-Radio) [Data 01
10 EXTERNAL CONTROL DEVICE SETUP ENGLISH ENG [Data 01][Data 02]: Major Channel Number Data 01: High byte Channel Data Data 02: Low byte Channel Data - 00 01 ~ 27 0F (Decimal: 1 ~ 9999) [Data 03][Data 04]: Minor/Branch Channel Number (Don’t care in Satellite) Data 03: High byte Channel Data Data 04: Low byte Channel Data Data 05 : Input Source (Digital/Satellite for Japan) - 02 : Terrestrial TV (DTV) - 07 : BS (Broadcasting Satellite) - 08 : CS1 (Communication Satellite 1) - 09 : CS2 (Communication Satell
EXTERNAL CONTROL DEVICE SETUP 23. Extended 3D(Command: x v) (only 3D models) (Depending on model) (Depending on model) ►► To change 3D option for TV. ►► To change 3D mode for TV.