User’s Guide 710E 710S 710B Make sure to read the Important Precautions before using the product. Keep the User's Guide(CD) in an accessible place for furture reference. See the label attached on the back cover and quote this information to your dealer when you require service.
Important Precautions This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential eletrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this monitor, observe the following basic rules for its installation, use, and servicing. Keep it in an accessible place for future reference. On Safety Use only the power cord supplied with the unit.
Important Precautions To Prevent Fire or Hazards: Always turn the monitor OFF if you leave the room for more than a short period of time. Never leave the monitor ON when leaving the house. Keep children from dropping or pushing objects into the monitor's cabinet openings. Some internal parts carry hazardous voltages. Do not add accessories that have not been designed for this monitor.
Connecting the Monitor Before setting up the monitor, ensure that the power is turned off to the monitor, computer system, and other attached devices. Carefully set the monitor face-down with the underside facing you. Connecting the Tilt/Swivel stand 1. Align the hooks on the tilt/swivel stand with the matching slots in the base of the monitor. 2. Insert the hooks into slots. 3. Slide the tilt/swivel stand toward the front of the monitor until the latches click into the locked position.
Connecting the Monitor Using the Computer 1. Connect the signal cable. When mated, tighten the thumbscrews to secure the connection. 2. Connect the power cord into a properly power outlet that is easily accessible and close to the monitor. NOTE This is a simplified representation of the rear view. This rear view represents a general model; your monitor may differ from the view as shown. Signal Cable Power Cord Attached Type* * Detached Type* * Varies according to model.
Control Panel Functions Front Panel Controls Control Function Power Button Use this button to turn the monitor on or off. Power (DPMS) Indicator This Indicator lights up green when the monitor operates normally. If the monitor is in DPM (Energy Saving) mode, this indicator will flicker. MENU Button Use this button to enter or exit the on screen display. Buttons SELECT Button CONTROLS LOCKED CONTROLS UNLOCKED Use these buttons to choose or adjust items in the on screen display.
On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the monitor is quick and easy with the On Screen Display Control system. A short example is quick and easy given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make using the OSD. NOTE Allow the monitor to stabilize for at least 30 minutes before making image adjustments.
On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus.
On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Icon Sub menu Description To adjust the contrast of the screen. CONTRAST To adjust the brightness of the screen. BRIGHTNESS To move image left and right. H POSITION To adjust image width. H SIZE To move image up and down.
On Screen Display(OSD) Selection and Adjustment Icon Sub menu TOP CORNER To correct an irregular distortion of the displayed image. * To correct an irregular distortion of the displayed image. * BOTTOM CORNER H CORNER To correct an irregular distortion of the displayed image. * This item allows you to reduce the degree of moire. (Moire is caused by interference Horizontal Scan Line with the periodical dot screen). It is normally OFF(H:0/V:0).
On Screen Display(OSD) Selection and Adjustment Icon Sub menu • OK • CANCEL RESET • 5 • 10 • 20 • 30 • 60 Set the OSD time, i.e. the length of time a menu will remain on-screen before it shuts off automatically. Adjust the time to 5, 10, 20, 30 or 60 seconds. • 0.7V • 1.0V This item is used to select the monitor's input signal level. The normal level used for most PCs is 0.7V. If the screen becomes suddenly washed-out or blurred, please select 1.0V and try again.
Troubleshooting Check the following before calling for service. No image appears ❐ Is the power cord of the monitor connected? • Check and see if the power cord is connected properly to the power outlet. ❐ Is the power indicator light on? • Press the Power button. ❐ Is the power on and the power indicator green? • Adjust the brightness and the contrast.
Troubleshooting The screen color is not normal. ❐ Do you see basic • Set the color depth to 256 colors or higher: use 'Control discoloration (16 colors)? Panel' -> 'Display' -> 'Settings' ->'Color Palette' ❐ Is the screen color • Check the connection of the signal cable. Or pull out the unstable or monochrome? video card of the PC and insert it again.
Specifications Picture Tube Sync Input Video Input Resolution Plug&Play Power Consumption Dimensions &Weight (with tilt/ swivel stand) Power Input Environmental Conditions Tilt/Swivel Stand Signal cable Power cord Regulations 17 inches (16.06 inches viewable) 90 degree deflection 0.23 mm / 0.27 mm (Ph/Pp) AGARAS(Anti-Glare Anti-Reflective Anti-Static) coating (710S) Horizontal Freq. 30 - 71kHz (Automatic) Vertical Freq.
Specifications Preset Modes (Resolution) Display Modes (Resolution) 1 2 3 4 VESA VESA VESA VESA Horizontal Freq. (kHz) 37.50 46.88 53.68 68.677 640 x 480 800 x 600 800 x 600 1024 x 768 A14 Vertical Freq.
Digitally yours