PLASMA MONITOR MODELS: 71PY1M 71PY1MG 71PY1MC 71PY1MV OWNER’S MANUAL Please read this manual carefully before operating your set. Retain it for future reference. Record model number and serial number of the set. See the label attached on the back cover and quote this information to your dealer when you require service.
Safety Instructions Safety Instructions WARNING Do not place the set in direct sunlight or near heat sources such as heat registers, stove and so on. - This may cause a fire. Do not use the set in damp place such as a bathroom or any place where it is likely to get wet. - This may cause a fire or could give an electric shock. Bend antenna cable between inside and outside building to prevent rain from flowing in. - This may cause water damaged inside the set and could give an electric shock.
Safety Instructions ENGLISH * Safety instructions have two kinds of information, and each meaning of it is as below. WARNING The violation of this instruction may cause serious injuries and even death. NOTES The violation of this instruction may cause light injuries or damage of the product. Take care of danger that may happen under specific condition. NOTES Never touch the power plug with a wet hand. - This may cause an electric shock.
Safety Instructions Safety Instructions continued CAUTION concerning the Power Cord : - Most appliances recommend they be connected to a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. - This may cause a fire or an electric shock. - Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous.
Contents ENGLISH Contents Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2~4 Introduction Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Controls and Connection Options . . . . . . . . . .8~9 Remote Control Key Functions . . . . . . . . . .10~11 Installation Installation Instructions . . . . . . . . . . . . . . . . . . . . .12 External Equipment Connections . . . . . . . . . .13~17 VCR Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Introduction Introduction What is a Plasma Display Panel? If voltage is applied to gas within glass panels, ultraviolet rays are produced and fused with a fluorescent substance. At that instant, light is emitted. A Plasma Display is a next generation flat Display using this phenomenon. 160° - Wide angle range of vision Your flat panel plasma screen offers an exceptionally broad viewing angle -- over 160 degrees. This means that the display is clear and visible to viewers anywhere in the room.
Introduction ENGLISH Accessories Ensure that the following accessories are included with your plasma display. If an accessory is missing, please contact the dealer where you purchased the product. MODE LIGHT POWER PIP INPUT DW DASP APC MUTE SLEEP VOL CH WIN. POSITION SWAP WIN.
Introduction Controls - Here shown may be somewhat different from your set. Front Panel Controls INDEX Switches LED Display on or off. INPUT VOL MENU Sub power Button E, D Buttons Remote Control Sensor VOLUME (F,G) Buttons Power Indicator Illuminates red in standby mode, Illuminates green when the monitor is turned on. MENU Button INPUT Button INDEX Video Mode Flat G p.22 Component Mode Music G p.22 RGB(DTV/PC) Mode Movie G p.22 HDMI1/DVI or HDMI2 Mode Sports G p.22 Off G p.
Introduction ENGLISH Connection Options - Here shown may be somewhat different from your set.
Introduction Remote Control Key Functions - When using the remote control, aim it at the remote control sensor on the monitor. - Under certain conditions such as if the remote IR signal is interrupted, the remote control may not function. Press the key again as necessary. LIGHT Illuminates the remote control buttons. LIGHT MODE POWER INPUT PIP DW DASP APC MUTE SLEEP VOL MODE Selects the remote operating mode: MNT, VCR, DVD, CABLE, HDSTB or AUDIO.
Introduction ENGLISH APC Adjusts the factory preset picture according to the room. Daylight, Optimum, Night time or Off (Refer to p.19) LIGHT MODE POWER INPUT PIP DW DASP To select the sound appropriate to your viewing program character: SRS TSXT, Flat, Music, Movie, Sports, or Off (Refer to p.22) MUTE Switches the sound on or off. DASP APC MUTE SLEEP VOL CHANNEL UP/DOWN Selects available channels. Dosen’t work for monitor mode. WIN.
Installation Installation Installation Instructions • Install this monitor only in a location where adequate ventilation is available. GROUNDING Power Supply Ensure that you connect the grounding / earth wire to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes.
Installation ENGLISH External Equipment Connections NOTE: Not all cables shown are included with the plasma display. VCR Setup - To avoid picture noise (interference), leave an adequate distance between the VCR and Monitor. - Use the ISM Method feature to avoid having a fixed image remain on the screen for a long period of time. Typically a frozen still picture from a VCR. If the 4:3 picture format is used; the fixed image may remain visible on the screen. How to connect 1.
Installation External Equipment Connections Cable TV Setup - After subscribing to a cable monitor service from a local provider and installing a converter, you can watch cable TV programming. The monitor cannot display monitor programming unless a TV tuner device or cable TV converter box is connected to the Monitor. - For further information regarding cable monitor service, contact your local cable TV service provider(s). How to connect 1.
Installation ENGLISH DVD Setup HDMI IN 2 HDMI IN RS-232C IN (CONTROL & SERVICE) ( VIDEO RS-232C IN (CONTROL & SERVICE) 2 VIDEO ( 1(DVI) VIDEO AUDIO VIDEO IN ) VIDEO S-VIDEO AUDIO VIDEO AUDIO AU VIDEO S-VIDEO AUDIO AUDIO VIDEO S-VIDEO VIDEO S-VIDEO COMPONENT IN AUDIO COMPONENT IN VIDEO IN COMPONENT IN ) AUDIO VIDEO IN (MONO) (MONO) 1(DVI) AUDIO COMPONENT IN VIDEO IN or or HDMI OUTPUT (R) AUDIO (L) B S-VIDEO R (R) AUDIO (L) DVD How to connect 1.
Installation External Equipment Connections PC Setup - This monitor provides Plug and Play capability, meaning that the PC adjusts automatically to its settings. The monitor sends configuration information (EDID) to the PC using the Video Electronics Standard Association (VESA) Display Data Channel (DDC) protocol. - The monitor perceives 640x480, 60Hz as DTV 480p based on the PC graphic card. In this case, change the screen scanning rate for the graphic card. How to connect 1.
Installation Resolution 720x400 640x480 800x600 832x624 1024x768 1280x1024 1600x1200 1920x1080 ENGLISH Monitor Display Specifications (RGB-PC / HDMI/DVI-PC Mode) Horizontal Vertical Frequency(kHz) Frequency(Hz) 31.469 70.08 31.469 59.94 35.000 66.66 37.861 72.80 37.500 75.00 43.269 85.00 37.879 60.31 46.875 75.00 53.674 85.06 49.725 74.55 48.363 60.00 56.476 70.06 60.023 75.02 63.981 60.02 80.000 75.00 75.00 60.00 66.587 59.
Operation Operation Turning on the Monitor Turning on the Monitor just after installation 1. Connect power cord correctly. At this moment, the Monitor is switched to standby mode. 2. Press the INPUT or button on the Monitor or press the POWER, INPUT button on the remote control and then the Monitor will switch on. Menu Language Selection - The menus can be shown on the screen in the selected language. First select your language. 1. Press the MENU button and then use 2.
Operation ENGLISH Picture Menu Options - Readjust Picture menu settings for each following input source as preferred. Auto Picture Control (APC) - APC adjusts the Monitor for the best picture appearance. - When adjusting Picture menu options (contrast, brightness, color, sharpness, and tint) manually, APC automatically changes to Off. 1. Press the APC button repeatedly to select the picture appearance setup option as shown below.
Operation Picture Menu Options continued Fleshtone (Video1-2-3-4, (Video1-2-3-4, Component 1-2, RGB-DTV, RGB-DTV, HDMI1/DVI-DTV, HDMI1/DVI-DTV, HDMI2-DTV Mode only) - Use Fleshtone to select the desired skin color option. PICTURE PICTURE APC SOUND ACC TIMER SPECIAL SCREEN PIP/DW TIMER Contrast ACC Fleshtone Fleshtone SPECIAL 100 Brightness 55 Color 55 Sharpness 60 Tint Move APC SOUND Contrast SCREEN Brightness 55 PIP/DW Color 55 Sharpness 60 Tint 0 Select Move 1.
Operation ENGLISH Manual Picture Control (Off (Off option) - You can adjust picture contrast, brightness, color, sharpness, and tint to the levels you prefer. PICTURE PICTURE APC SOUND TIMER SPECIAL ACC PIP/DW Brightness SPECIAL 100 SCREEN 55 Color 55 Sharpness 60 Tint Move TIMER Fleshtone Contrast SCREEN APC SOUND PIP/DW ACC Fleshtone Contrast 60 Color 50 Sharpness 50 Tint 0 Select Move 1. Press the MENU button and then use menu.
Operation Sound Menu Options DASP (Digital Auto Sound Processing) - DASP lets you enjoy the best sound without any special adjustment because the Monitor has the appropriate sound options based on the program content. - When adjusting sound options (treble, bass) manually, DASP automatically changes to Off. 1. Press the DASP button repeatedly to select the appropriate sound setup as shown below. SRS TSXT Flat Music Movie Off Sports • You can also adjust DASP in the SOUND menu.
Operation ENGLISH BBE - BBE High Definition Sound restores clarity and presence for better speech intelligibility and musical realism. PICTURE DASP PICTURE DASP SOUND BBE SOUND BBE TIMER AVL TIMER SPECIAL Balance SCREEN 0 Treble 50 Bass 50 SPECIAL SCREEN PIP/DW Move Balance On Off 0 Treble 50 Bass 50 PIP/DW Select Move 1. Press the MENU button and then use D /E D /E button to select BBE. 3. Press the D /E button to select On or Off.
Operation T imer Menu Options Clock Setup - If current time setting is wrong, correct the clock setting. PICTURE Clock PICTURE Clock SOUND Off timer SOUND Off timer TIMER On timer SPECIAL TIMER Auto off SPECIAL SCREEN SCREEN PIP/DW PIP/DW Move Select Move 1. Press the MENU button and then use G -- : -- AM On timer Auto off Select button to select the TIMER menu. D /E / E button to select Clock. 2. Press the G button and then use D 3.
Operation ENGLISH Auto Off Off - If there is no input signal, the Monitor turns off automatically after 10 minutes. PICTURE Clock PICTURE Clock SOUND Off timer SOUND Off timer TIMER On timer TIMER On timer SPECIAL Auto off SPECIAL SCREEN SCREEN PIP/DW PIP/DW Move Select Move 1. Press the MENU button and then use D /E 2. Press the G On Off Select button to select the TIMER menu. button and then use D /E button to select Auto off. 3.
Operation Special Menu Options Key Lock - The monitor can be set up so that it can only be used with the remote control. - This feature can be used to prevent unauthorized viewing by disabling the front panel controls. - This Monitor is programmed to remember which option it was last set to even if you turn the monitor off.
Operation ENGLISH Low Power - Low power reduces the plasma display's power consumption. PICTURE Language PICTURE Language SOUND Key lock SOUND Key lock TIMER ISM Method TIMER ISM Method SPECIAL Low power SCREEN SPECIAL SCREEN Index PIP/DW Move Low power G Set ID Set ID On Off Index PIP/DW Select Move 1. Press the MENU button and then use D /E 2. Press the G button and then use D /E button to select Low power. 3.
Operation Screen Menu Options Auto Adjustment - RGB (PC) mode only; This function doesn’t work for RGB(DTV). Automatically adjusts picture position and minimizes image shaking. After adjustment, if the image is still not correct, your Monitor is functioning properly but needs further adjustment. The Auto config., Position and Manual config. are not active in HDMI/DVI mode. PICTURE PICTURE Auto config. Auto config.
Operation ENGLISH Cinema Mode Setup (Video1-2 (Video1-2 and Component 480i mode only) - Sets up the monitor for the best picture appearance for viewing movies. PICTURE PICTURE Auto config. SOUND ARC SOUND ARC TIMER Cinema TIMER Cinema SPECIAL Auto config. Position SPECIAL PIP/DW SCREEN NR PIP/DW Reset Off NR Reset Black level adj. Black level adj. Move On Manual config. Manual config. SCREEN G Position Select Move 1.
Operation Screen Menu Options continued Manual Configure (RGB-PC mode only) - If the image still isn’t clear after auto adjustment is completed and especially if characters are still jittery, adjust the picture Phase manually. - To correct the screen size, adjust Clock. PICTURE Auto config. PICTURE Auto config. SOUND ARC SOUND ARC TIMER Cinema TIMER Cinema Position SPECIAL SPECIAL SCREEN Move SCREEN NR PIP/DW PIP/DW Reset Black level adj.
Operation ENGLISH Black level adj. - Adjusting the contrast and the brightness of the screen using the black level of the screen. - This feature operates only in Video1-2-3-4 or Component 576i mode. PICTURE Auto config. PICTURE Auto config. SOUND ARC SOUND ARC TIMER Cinema TIMER Cinema Position SPECIAL SPECIAL SCREEN SCREEN NR PIP/DW PIP/DW Reset NR Reset G Black level adj. Black level adj. Move Position Manual config. Manual config. Move Select 1.
Operation Screen Menu Options continued Screen Adjustments (Video1-2 (Video1-2 and Component 480i mode only) - Use this function to correct jittering or picture instability while viewing a video tape. PICTURE PICTURE Screen adj. SOUND ARC SOUND ARC TIMER Cinema TIMER Cinema SPECIAL NR Screen adj. VCR Reset SCREEN Black level adj. Black level adj. PIP/DW PIP/DW Move TV NR SPECIAL Reset SCREEN G Move Select 1.
Operation - PIP lets you view 2 different inputs (sources) on your monitor screen at the same time. One source will be large, and the other source will show a smaller inset image. - If input signals(50Hz/60Hz) of the main and sub pictures are different in PIP/DW mode, the screens are unnatural. PIP Size Watching PIP Press the WIN.SIZE button and then use change the sub picture size. Press the PIP button repeatedly to turn PIP on or off. PIP Transparency (PIP Mode only) 1.
Operation DW Setup Options - As the name suggests, this mode splits the screen into 2, allowing 2 picture sources to be shown on the monitor screen at the same time. Each source is given half the screen. Watching DW Press the DW button repeatedly to select one of the DW options. DW1 DW2 Off Sub Picture Size Adjustment Press the WIN.SIZE button. • Use the F / G button to change the sub picture size. • Using the WIN.SIZE function in DW mode, main and sub picture sizes are changed simultaneously.
External Control Device Setup ( VIDEO ) AUDIO VIDEO IN S-VIDEO ENGLISH External Control Device Setup AUDIO VIDEO COMPONENT IN - Connect the RS-232C input jack to an external control device (such as a computer or an A/V control system) and control the Monitor’s functions externally. - Connect the serial port of the control device to the RS-232C jack on the Monitor back panel. - RS-232C connection cables are not supplied with the Monitor.
External Control Device Setup Set ID - Use this function to specify a monitor ID number. - Refer to ‘Real Data Mapping 1’. See page 38. PICTURE Language PICTURE Language SOUND Key lock SOUND Key lock TIMER ISM Method TIMER ISM Method SPECIAL Low power SCREEN SPECIAL SCREEN Index PIP/DW Move Low power Set ID Set ID G 1 Index PIP/DW Select Move 1. Press the MENU button and then use the 2. Press the G button and then use D /E 3.
External Control Device Setup 04. Screen Mute (Command 2:d) G To control Power On/Off of the Monitor. G To select screen mute on/off. Transmission Transmission [k][a][ ][Set ID][ ][Data][Cr] Data 0 : Power Off ENGLISH 01. Power (Command 2:a) [k][d][ ][Set ID][ ][Data][Cr] 1 : Power On Acknowledgement Data 0 : Screen mute off (Picture on) 1 : Screen mute on (Picture off) [a][ ][Set ID][ ][OK][Data][x] Acknowledgement [d][ ][Set ID][ ][OK][Data][x] G To show Power On/Off.
External Control Device Setup 07. Contrast (Command 2:g) 10. Tint (Command2:j) G To adjust screen contrast. You can also adjust contrast in the picture menu. G To adjust the screen tint. You can also adjust tint in the Picture menu. Transmission Transmission [k][g][ ][Set ID][ ][Data][Cr] [k][j][ ][Set ID][ ][Data][Cr] Data Min : 0 ~ Max : 64 • Refer to ‘Real data mapping1’ as shown below. Data Red : 0 ~ Green : 64 • Refer to ‘Real data mapping 1’.
External Control Device Setup 18. Balance (Command2:t) G To control the PIP (Picture-in-Picture) or DW. You can also control the PIP/DW using the PIP or DW button on the remote control or in the PIP/DW menu. G To adjust balance. You can also adjust balance in the Sound menu. Transmission [k][t][ ][Set ID][ ][Data][Cr] [k][n][ ][Set ID][ ][Data][Cr] Data 0: PIP/DW off 1: PIP 2: DW1 3: DW2 Acknowledgement Data Min: 0 ~ Max: 64 • Refer to ‘Real data mapping 1’. See page 38.
External Control Device Setup * Real data mapping 2 26. Low Power (Command2:q) 0 : -10 1 :-9 2 :-8 G To control the low power function on/off. A : 0 Data 0: Low power off 1: Low power on Acknowledgement Transmission [j][q][ ][Set ID][ ][Data][Cr] 12 : + 8 13 : + 9 14 : + 10 [q][ ][Set ID][ ][OK][Data][x] Data 0: Low power off 1: Low power on 23. PIP Input Select (Command2:y) G To select input source for sub picture in PIP mode. Transmission 27.
IR Code ENGLISH IR Code How to Connect G Connect your wired remote control to the Remote Control port on the Monitor. Remote Control IR Code G Output waveform Single pulse, modulated with 37.
IR Code Code (Hexa) 10 11 12 13 14 15 16 17 18 19 0E 09 08 02 03 00 01 4D 52 44 0B 43 79 62 64 07 06 40 41 5B 60 92 61 6B CD CE 3E 75 99 5A D0 BF D4 D5 C6 42 Plasma Monitor Function Number Key 0 Number Key 1 Number Key 2 Number Key 3 Number Key 4 Number Key 5 Number Key 6 Number Key 7 Number Key 8 Number Key 9 SLEEP MUTE POWER VOL+ VOLCH+ CHAPC DASP ENTER (Á) AII INPUT SELECT MENU ARC Window Position Window Size F G D E EXIT PIP XD PIP Input DW Video HDMI2 Key lock Index Auto config.
Programming the Remote G The remote control is a multi-brand or universal remote control. It can be programmed to operate most remote-controllable devices of other manufacturers. Note that the remote control may not control all models of other brands. Programming a code into a remote mode 1. Test your remote control.
Programming the Remote Programming Codes VCRs Brand Codes Brand Codes Brand Codes Brand Codes AIWA AKAI 034 016 125 072 031 012 035 028 108 003 031 005 065 112 108 012 034 059 006 029 036 129 003 034 031 107 132 012 004 043 031 031 012 040 043 012 048 130 KENWOOD 014 047 001 101 034 003 017 040 031 067 012 069 101 027 031 003 033 101 045 013 013 049 151 034 024 012 048 043 053 066 133 013 063 031 031 067 101 013 PORTLAND PULSAR QUARTZ QUASAR RCA 108 072 011 033 013 040 107 145 003 031 053 058
Programming the Remote ENGLISH HDSTB Brand Codes Brand ALPHASTAR DSR AMPLICA BIRDVIEW BSR CAPETRONICS CHANNEL MASTER 123 050 051 053 053 013 036 008 054 050 005 011 141 024 038 093 097 122 089 EUROPLUS FUJITSU CHAPARRAL CITOH CURTIS MATHES DRAKE DX ANTENNA ECHOSTAR ELECTRO HOME 126 129 014 015 018 055 009 012 077 145 006 007 010 052 112 116 046 040 094 098 056 057 095 099 076 058 096 100 Codes 114 017 133 GENERAL INSTRUMENT 003 031 HITACHI 139 HOUSTON TRACKER 033 057 HUGHES 068 HYTEK 053 JAN
Troubleshooting Checklist Troubleshooting Checklist • Check whether the Monitor is turned on. No picture & No sound • Power cord inserted into wall outlet? • Test the wall power outlet, plug other product’s power cord into the wall outlet where the Monitor’s power cord was plugged in. Picture OK & No sound • Press the VOLUME (+) button. • Sound muted? Press MUTE button. • Check to see if there is any object between the Plasma Display and the remote control causing obstruction.
Product Specifications ENGLISH Product Specifications 71PY1M 71PY1MG 71PY1MC 71PY1MV (71PY1M-WA) (71PY1MG-WA) (71PY1MC-WA) (71PY1MV-WA) Width (inches / mm) 68.9 / 1750 68.9 / 1750 68.9 / 1750 68.9 / 1750 Height (inches / mm) 38.7 / 982 38.7 / 982 38.7 / 982 38.7 / 982 Depth (inches / mm) 3.9 / 98 3.9 / 98 3.9 / 98 3.9 / 98 Weight (pounds / kg) 194.9 / 88.4 194.9 / 88.4 194.9 / 88.4 194.9 / 88.