PLASMA MONITOR MODELS: 71PY1M OWNER’S MANUAL Please read this manual carefully before operating your set. Retain it for future reference. Record model number and serial number of the set. See the label attached on the back cover and quote this information to your dealer when you require service.
Warning Warning WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
Safety Instructions Safety Instructions IMPORTANT SAFETY INSTRUCTIONS Important safety instructions shall be provided with each apparatus. This information shall be given in a separate booklet or sheet, or be located before any operating instructions in an instruction for installation for use and supplied with the apparatus. This information shall be given in a language acceptable to the country where the apparatus is intended to be used.
Safety Instructions 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 15. CAUTION concerning the Power Cord : Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits.
Contents Contents Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2~4 Introduction Features Of This TV . . . . . . . . . . . . . . . . . . . . . .6 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Controls and Connection Options . . . . . . . . . .8~9 Remote Control Key Functions . . . . . . . . . .10~11 Installation Desktop Pedestal Installation . . . . . . . . . . . . . . . .12 External Equipment Connections . . . . . . . . . .13~17 VCR Setup . . . . . .
Introduction Introduction Features Of This Monitor What is a Plasma Monitor ? If voltage is applied to gas within glass panels, ultraviolet rays are produced and fused with a fluorescent substance. At that instant, light is emitted. A Plasma Display is a next generation flat Display using this phenomenon. 160° - Wide angle range of vision Your flat panel plasma screen offers an exceptionally broad viewing angle -- over 160 degrees.
Introduction Accessories Ensure that the following accessories are included with your plasma display. If an accessory is missing, please contact the dealer where you purchased the product. R WE PO UT SP DA Owner’s Manual D-sub 15 pin cable IT E RE CO RD IP ST OP SK RG B IND EX FF CO M2 KEY W HD MI1 VID EO HDM I2 RE LOC K UT INP PIP NU PLA Y ME PA US E CO M1 SIZ EX N. AR C WI 1.5V 1.5V EN TE R WIN .
Introduction Controls - This is a simplified representation of front panel. - This picture shown below may be somewhat different from your monitor. INDEX Switches LED Display on or off. INPUT VOL MENU Sub power Button E, D Buttons VOLUME (F , G) Buttons Power Indicator Illuminates red in standby mode, Illuminates green when the monitor is turned on. MENU Button INPUT Button INDEX Video Mode Flat G p.22 Component Mode Music G p.22 RGB-PC/DTV Mode Movie G p.
Introduction Connection Options - This picture shown below may be somewhat different from your monitor.
Introduction Remote Control Key Functions - When using the remote control, aim it at the remote control sensor on the monitor. - Under certain conditions such as if the remote IR signal is interrupted, the remote control may not function. Press the key again as necessary. LIGHT Illuminates the remote control buttons. LIGHT MODE POWER INPUT PIP DW DASP APC MUTE SLEEP VOL CH MODE Selects the remote operating mode: MNT, VCR, DVD, CABLE, HDSTB or AUDIO.
Introduction APC Adjusts the factory preset picture according to the room. DASP To select the sound appropriate to your viewing program character: SRS TSXT, Flat, Music, Movie, Sports, or Off G p.22 LIGHT MODE POWER INPUT PIP DW MUTE Switches the sound on or off. SLEEP Sets the Sleep Timer. DASP APC MUTE SLEEP VOL CH VOLUME UP/DOWN Increases/decreases the sound level. CHANNEL UP/DOWN Selects available channels. Dosen’t work for monitor mode. WIN. POSITION SWAP WIN.
Installation Installation • Ensure adequate ventilation by following the clearance recommendations. 4 inches 4 inches 4 inches 4 inches For proper ventilation, allow a clearance of 4inches on each side from the wall. Desktop Pedestal Installation • This picture shown below may be somewhat different from your monitor. Power Supply Short-circuit Breaker GROUNDING Ensure that you connect the grounding / earth wire to prevent possible electric shock.
Installation External Equipment Connections NOTE: Not all cables shown are included with the plasma display. VCR Setup - To avoid picture noise (interference), leave an adequate distance between the VCR and Monitor. - Use the ISM Method feature to avoid having a fixed image remain on the screen for a long period of time. Typically a frozen still picture from a VCR. If the 4:3 picture format is used; the fixed image may remain visible on the screen after the image is changed or when the unit is off.
Installation Cable TV Setup - After subscribing to a cable monitor service from a local provider and installing a converter, you can watch cable TV programming. The monitor cannot display monitor programming unless a TV tuner device or cable TV converter box is connected to the Monitor. - For further information regarding cable monitor service, contact your local cable TV service provider(s). How to connect 1.
Installation DVD Setup HDMI IN RS-232C IN (CONTROL & SERVICE) 2 HDMI IN 2 RS-232C IN (CONTROL & SERVICE) ( VIDEO ) VIDEO S-VIDEO AUDIO VIDEO ) (MONO) VIDEO AUDIO COMPONENT IN AUDIO VIDEO S-VIDEO COMPONENT IN VIDEO IN AUDIO VIDEO S-VIDEO AUDIO AUDIO COMPONENT IN VIDEO IN ( 1(DVI) VIDEO AUDIO VIDEO S-VIDEO AUDIO VIDEO IN (MONO) 1(DVI) COMPONENT IN VIDEO IN or HDMI OUTPUT (R) AUDIO (L) S-VIDEO B R (R) AUDIO (L) DVD How to connect 1.
Installation PC Setup - This monitor provides Plug and Play capability, meaning that the PC adjusts automatically to its settings. The monitor sends configuration information (EDID) to the PC using the Video Electronics Standard Association (VESA) Display Data Channel (DDC) protocol. - The monitor perceives 640x480, 60Hz as DTV 480p based on the PC graphic card. In this case, change the screen scanning rate for the graphic card. How to connect 1.
Installation Monitor Display Specifications (RGB-PC / HDMI/DVI-PC Mode) Resolution 720x400 640x480 800x600 832x624 1024x768 1280x1024 1600x1200 1920x1080 Horizontal Vertical Frequency(KHz) Frequency(Hz) 31.469 70.08 31.469 59.94 35.000 66.66 37.861 72.80 37.500 75.00 43.269 85.00 37.879 60.31 46.875 75.00 53.674 85.06 49.725 74.55 48.363 60.00 56.476 70.06 60.023 75.02 63.981 60.02 80.000 75.00 75.00 60.00 66.587 59.
Operation Operation Turning on the Monitor Turning on the Monitor just after installation 1. Connect power cord correctly. At this moment, the Monitor is switched to standby mode. 2. Press the INPUT or button on the Monitor or press the POWER, INPUT button on the remote control and then the Monitor will switch on. Menu Language Selection - The menus can be shown on the screen in the selected language. First select your language. 1. Press the MENU button and then use 2.
Operation Picture Menu Options - Readjust Picture menu settings for each following input source as preferred. Auto Picture Control (APC) - APC adjusts the Monitor for the best picture appearance. - When adjusting Picture menu options (contrast, brightness, color, sharpness, and tint) manually, APC automatically changes to Off. 1. Press the APC button repeatedly to select the picture appearance setup option as shown below.
Operation Picture Menu Options continued Fleshtone (Video1-2-3-4, (Video1-2-3-4, Component 1-2, RGB-DTV, RGB-DTV, HDMI1/DVI-DTV, HDMI1/DVI-DTV, HDMI2-DTV Mode only) - Use Fleshtone to select the desired skin color option. APC APC ACC ACC Fleshtone Fleshtone Contrast Contrast 100 Brightness 55 Brightness 55 Color 55 Color 55 Sharpness 60 Sharpness 60 Tint Tint 0 1. Press the MENU button and then use D /E 2. Press the G button and then use D /E button to select Fleshtone. 3.
Operation Manual Picture Control ( Off option) - You can adjust picture contrast, brightness, color, sharpness, and tint to the levels you prefer. APC APC ACC ACC Fleshtone Fleshtone Contrast Contrast 100 100 Brightness 55 Brightness 60 Color 55 Color 50 Sharpness 60 Sharpness 50 Tint Tint 0 1. Press the MENU button and then use menu. D / E G 0 button to select the PICTURE 2.
Operation Sound Menu Options DASP (Digital Auto Sound Processing) - DASP lets you enjoy the best sound without any special adjustment because the Monitor has the appropriate sound options based on the program content. - When adjusting sound options (treble, bass) manually, DASP automatically changes to Off. 1. Press the DASP button repeatedly to select the appropriate sound setup as shown below. SRS TSXT Flat Music Movie Off Sports • You can also adjust DASP in the SOUND menu.
Operation BBE - BBE High Definition Sound restores clarity and presence for better speech intelligibility and musical realism. DASP DASP BBE BBE AVL AVL Balance Balance 0 50 Treble 50 Bass 50 Bass 50 /E button to select the SOUND menu. 2. Press the G button and then use D /E button to select BBE. 3. Press the D /E button to select On or Off. button and then use On Off 0 Treble 1. Press the MENU button and then use D G G 4. Press the ENTER button to save the new settings.
Operation T imer Menu Options Clock Setup - If current time setting is wrong, correct the clock setting. Clock Clock Off timer Off timer On timer On timer Auto off Auto off 1. Press the MENU button and then use G -- : -- AM button to select the TIMER menu. D /E 2. Press the G button and then use D /E button to select Clock. 3. Press the G button and then use D /E button to set the hour. 4. Press the G button and then use D /E button to set the minutes. 5.
Operation Auto Off Off - If there is no input signal, the Monitor turns off automatically after 10 minutes. Clock Clock Off timer Off timer On timer On timer Auto off Auto off G On Off button to select the TIMER menu. 1. Press the MENU button and then use D /E 2. Press the G button and then use D /E button to select Auto off. 3. Press the G button and then use D /E button to select On or Off. 4. Press the ENTER button to save the new settings.
Operation Special Menu Options Key Lock - The monitor can be set up so that it can only be used with the remote control. - This feature can be used to prevent unauthorized viewing by disabling the front panel controls. - This Monitor is programmed to remember which option it was last set to even if you turn the monitor off. Language Language Key lock Key lock ISM Method ISM Method Low power Low power Set ID Set ID Index Index 1. Press the MENU button and then use 2.
Operation Low Power - Low power reduces the plasma display's power consumption. Language Language Key lock Key lock ISM Method ISM Method Low power Low power Set ID Set ID Index Index G On Off button to select the SPECIAL menu. 1. Press the MENU button and then use D /E 2. Press the G button and then use D /E button to select Low power. 3. Press the G button and then use D /E button to select On or Off. • When you select On, the screen darkens. 4.
Operation Screen Menu Options Auto Adjustment - RGB (PC) mode only; This function doesn’t work for RGB-DTV. Automatically adjusts picture position and minimizes image shaking. After adjustment, if the image is still not correct, your Monitor is functioning properly but needs further adjustment. The Auto config., Position and Manual config. are not active in HDMI/DVI mode. Auto config. Auto config. ARC ARC Cinema Cinema Position Position Manual config. Manual config.
Operation Cinema Mode Setup (Video1-2 (Video1-2 and Component 480i mode only) - Sets up the monitor for the best picture appearance for viewing movies. Auto config. Auto config. ARC ARC Cinema Cinema Position Position Manual config. Manual config. NR NR Reset Reset Black level adj. Black level adj. 1. Press the MENU button and then use D /E G On Off button to select the SCREEN menu. 2. Press the G button and then use D /E button to select Cinema. 3.
Operation Screen Menu Options continued Manual Configure (RGB-PC mode only) - If the image still isn’t clear after auto adjustment is completed and especially if characters are still jittery, adjust the picture Phase manually. - To correct the screen size, adjust Clock. Auto config. Auto config. ARC ARC Cinema Cinema Position Position Manual config. Manual config. NR NR Reset Reset Black level adj. Black level adj. PC/DTV Mode PC/DTV Mode 1. Press the MENU button and then use D /E 2.
Operation Black level adj. - Adjusting the contrast and the brightness of the screen using the black level of the screen. This feature operates only in Video1-2-3-4 or Component 480i mode. Auto config. Auto config. ARC ARC Cinema Cinema Position Position Manual config. Manual config. NR NR Reset Reset Black level adj. Black level adj. 1. Press the MENU button and then use D /E 2. Press the G button and then use button to select Black level adj.
Operation Screen Menu Options continued Screen Adjustments (Video1-2 (Video1-2 and Component 480i mode only) - Use this function to correct jittering or picture instability while viewing a video tape. Screen adj. Screen adj. ARC ARC Cinema Cinema NR NR Reset Reset Black level adj. Black level adj. 1. Press the MENU button and then use D /E G TV VCR button to select the SCREEN menu. 2. Press the G button and then use D /E button to select Screen adj.. 3.
Operation PIP (Picture-In-Picture) Feature - PIP lets you view 2 different inputs (sources) on your monitor screen at the same time. One source will be large, and the other source will show a smaller inset image. - If input signals(50Hz/60Hz) of the main and sub pictures are different in PIP/DW mode, the image will not display properly. PIP Size Watching PIP Press the PIP button repeatedly to turn PIP on or off. Press the WIN.SIZE button and then use change the sub picture size.
Operation DW Setup Option - As the name suggests, this mode splits the screen into 2, allowing 2 picture sources to be shown on the monitor screen at the same time. Each source is given half the screen. Watching DW Press the DW button repeatedly to select one of the DW options. Off DW2 DW1 Sub Picture Size Adjustment Press the WIN.SIZE button. • Use the F / G button to change the sub picture size. • Using the WIN.SIZE function in DW mode, main and sub picture sizes are changed simultaneously.
External Control Device Setup External Control Device Setup ( VIDEO ) AUDIO VIDEO IN S-VIDEO AUDIO VIDEO COMPONENT IN - Connect the RS-232C input jack to an external control device (such as a computer or an A/V control system) and control the Monitor’s functions externally. - Connect the serial port of the control device to the RS-232C jack on the Monitor back panel. - RS-232C connection cables are not supplied with the Monitor.
External Control Device Setup Set ID - Use this function to specify a monitor ID number. - Refer to ‘Real Data Mapping 1’. See page 38. Language Language Key lock Key lock ISM Method ISM Method Low power Low power Set ID Set ID Index Index 1. Press the MENU button and then use the 2. Press the G button and then use D /E 3. Press the G button and then use F /G D /E G 1 button to select the SPECIAL menu. button to select Set ID.
External Control Device Setup 01. Power (Command 2:a) 04. Screen Mute (Command 2:d) G To control Power On/Off of the Monitor. G To select screen mute on/off. Transmission Transmission [k][a][ ][Set ID][ ][Data][Cr] Data 0 : Power Off [k][d][ ][Set ID][ ][Data][Cr] 1 : Power On Acknowledgement Data 0 : Screen mute off (Picture on) 1 : Screen mute on (Picture off) [a][ ][Set ID][ ][OK][Data][x] Acknowledgement [d][ ][Set ID][ ][OK][Data][x] G To show Power On/Off.
External Control Device Setup 07. Contrast (Command 2:g) 10. Tint (Command2:j) G To adjust screen contrast. You can also adjust contrast in the picture menu. G To adjust the screen tint. You can also adjust tint in the Picture menu. Transmission Transmission [k][g][ ][Set ID][ ][Data][Cr] [k][j][ ][Set ID][ ][Data][Cr] Data Min : 0 ~ Max : 64 • Refer to ‘Real data mapping1’ as shown below. Data Red : 0 ~ Green : 64 • Refer to ‘Real data mapping 1’.
External Control Device Setup 14. PIP / DW (Command2:n) 17. Bass (Command2:s) G To control the PIP (Picture-in-Picture) or DW. You can also control the PIP/DW using the PIP or DW button on the remote control or in the PIP/DW menu. G To adjust bass. You can also adjust bass in the Sound menu. Transmission [k][s][ ][Set ID][ ][Data][Cr] [k][n][ ][Set ID][ ][Data][Cr] Data 0: PIP/DW off 1: PIP 2: DW1 3: DW2 Acknowledgement Data Min: 0 ~ Max: 64 • Refer to ‘Real data mapping 1’. See page 38.
External Control Device Setup 20. PIP Input Select (Command2:y) 23. Low Power (Command2:q) G To select input source for sub picture in PIP mode.
IR Code IR Code How to Connect G Connect your wired remote control to the Remote Control port on the Monitor. Remote Control IR Code G Output waveform Single pulse, modulated with 37.
IR Code Code (Hexa) 10 11 12 13 14 15 16 17 18 19 0E 09 08 02 03 00 01 4D 52 44 0B 43 79 62 64 07 06 40 41 5B 60 92 61 6B CD CE 3E 75 99 5A D0 BF D4 D5 C6 42 Plasma Monitor Function Number Key 0 Number Key 1 Number Key 2 Number Key 3 Number Key 4 Number Key 5 Number Key 6 Number Key 7 Number Key 8 Number Key 9 SLEEP MUTE POWER VOL+ VOLCH+ CHAPC DASP ENTER (Á) AII INPUT SELECT MENU ARC Window Position Window Size F G D E EXIT PIP XD PIP Input DW Video HDMI2 Key lock Index Auto config.
Programming the Remote Programming the Remote G The remote control is a multi-brand or universal remote control. It can be programmed to operate most remote-controllable devices of other manufacturers. Note that the remote control may not control all models of other brands. Programming a code into a remote mode 1. Test your remote control.
Programming the Remote Programming Codes VCRs Brand Codes Brand Codes Brand Codes Brand Codes AIWA AKAI 034 016 125 072 031 012 035 028 108 003 031 005 065 112 108 012 034 059 006 029 036 129 003 034 031 107 132 012 004 043 031 031 012 040 043 012 048 130 KENWOOD 014 047 001 101 034 003 017 040 031 067 012 069 101 027 031 003 033 101 045 013 013 049 151 034 024 012 048 043 053 066 133 013 063 031 031 067 101 013 PORTLAND PULSAR QUARTZ QUASAR RCA 108 072 011 033 013 040 107 145 003 031 053 058
Programming the Remote HDSTB Brand Codes Brand ALPHASTAR DSR AMPLICA BIRDVIEW BSR CAPETRONICS CHANNEL MASTER 123 050 051 053 053 013 036 008 054 050 005 011 141 024 038 093 097 122 089 EUROPLUS FUJITSU CHAPARRAL CITOH CURTIS MATHES DRAKE DX ANTENNA ECHOSTAR ELECTRO HOME 126 129 014 015 018 055 009 012 077 145 006 007 010 052 112 116 046 040 094 098 056 057 095 099 076 058 096 100 Codes 114 017 133 GENERAL INSTRUMENT 003 031 HITACHI 139 HOUSTON TRACKER 033 057 HUGHES 068 HYTEK 053 JANIEL 060 J
Troubleshooting Checklist Troubleshooting Checklist • Check whether the Monitor is turned on. No picture & No sound • Power cord inserted into wall outlet? • Test the wall power outlet, plug other product’s power cord into the wall outlet where the Monitor’s power cord was plugged in. Picture OK & No sound • Press the VOLUME (+) button. • Sound muted? Press MUTE button. • Check to see if there is any object between the Plasma Display and the remote control causing obstruction.
Specifications Product Specifications MODELS Width (inches / mm) Height (inches / mm) Depth (inches / mm) Weight (pounds / kg) Power requirement Resolution Viewing Size (mm) Operating Temperature Environmental condition Operating Humidity Storage Temperature Storage Humidity 71PY1M (71PY1M-WA) 68.9 / 1750.0 38.7 / 982.0 3.9 / 98.0 194.9 / 88.4 AC100-240V ~ 50/60Hz 1920 x 1080 (Dot) 1512.
