ENGLISH ITALIANO ESPAÑOL FRANÇAIS DEUTSCH OWNER’S MANUAL AIR CONDITIONER Please read this manual carefully before operating your set and retain it for future reference. TYPE : FLOOR STANDING The equipment complies with requirements of the Technical Regulation, in terms of restrictions for the use of certain dangerous substances in electrical and electronic equipment. www.lg.
Floor Standing- Type Air Conditioner Ownerʼs Manual TABLE OF CONTENTS FOR YOUR RECORDS Safety Precautions.................3 Write the model and serial numbers here: Model # Serial # Prior to Operation ..................6 You can find them on a label on the side of each unit. Dealer's Name Date Purchased Indtroduction ..........................6 Operating Instructions...........5 Maintenance and Service ....
Safety Precautions To prevent injury to the user or other people and property damage, the following instructions must be followed. n Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness is classified by the following indications. WARNING This symbol indicates the possibility of death or serious injury. CAUTION This symbol indicates the possibility of injury or damage. n Meanings of symbols used in this manual are as shown below. Be sure not to do.
Safety Precautions For installation, always contact the dealer or an Authorized Service Center. • There is risk of fire, electric shock, explosion, or injury. Do not install the product on a defective installation stand. • It may cause injury, accident, or damage to the product. Be sure the installation area does not deteriorate with age. • If the base collapses, the air conditioner could fall with it, causing property damage, product failure, and personal injury.
Safety Precautions n Installation Always check for gas (refrigerant) leakage after installation or repair of product. • Low refrigerant levels may cause failure of product. Do not install the product where the noise or hot air from the outdoor unit could damage the neighborhoods. • It may cause a problem for your neighbors. Install the drain hose to ensure that water is drained away properly. • A bad connection may cause water leakage. Use two or more people to lift and transport the product.
Prior to Operation Prior to Operation Preparing for Operation 1. Contact an installation specialist for installation. 2. Plug in the power plug properly. 3. Use a dedicated circuit. 4. Do not use an extension cord. 5. Do not start/stop operation by plugging/unplugging the power cord. 6. If the cord/plug is damaged, replace it with only an authorized replacement part. Usage 1. Being exposed to direct airflow for a long time may be hazardous to your health.
Safety Precautions Operating Instructions ENGLISH Operating Instructions Features and Specifications 1. 3D Stereo Cooling This first developed 3D Stereo Cooling Method makes clear a dead zone to cool the indoor evenly within a early time. 7. Whisper quiet operation 8. Wireless remote control 9. 3 cooling speeds 2 heating speeds 10. Removable air filter 11. Anti-Bacteria filter 12. 3 minutes delay circuit 13. Turbo-Z operation 14. Energy saving 15. Auto restart 16. Plasma Air Purifying system 2.
Operating Instructions Indoor Unit Controls and Indicators SET ROOM TEMP. ON/OFF PLASMA TURBO-Z 1 2 3 4 5 6 7 8 9 10 11 12 13 (Cooling Model) SET ROOM TEMP. ON/OFF PLASMA TURBO-Z 1 14 4 3 15 5 6 7 8 9 10 11 12 13 (Heat Pump Model) SET ROOM TEMP. ON/OFF PLASMA TURBO-Z 1 14 4 3 16 15 5 6 7 8 9 10 11 12 13 (Heater & Heat Pump Model) 1. Energy Saving Operation Key 2. Auto Operation Key 3. Soft Dry Operation Key 4. Cooling Operation Key 5.
Operating Instructions ENGLISH Name and Function-Remote Control 1 15 2 9 4 A/CL 3 10 5 11 6 TURBO-Z 7 12 8 13 1. Signal Transmitter • Transmits the signals to the Floor Standing Type air conditioner 2. Operation Display of the Remote Control 3. Timer Set Button • Each time the button is pressed, the mode is changed in the following process. Timer set (1, 2, 3, 4, 5, 6, 7 hours) If you select “0:00” the off Timer function will be canceled. 4. Plasma Airfurifying Button 14 5.
Operating Instructions Remote Control Preparation 1. How to mount onto a wall Use the screws to secure the holder to the wall or attach the holder side of indoor unit. • Please keep it on the right side of indoor unit. When opening When closing 2. To insert the remote control to the holder. Insert Pull How to insert batteries 1. Remove the cover from the back of the remote controller. • Slide the cover according to the arrow direction.
Operating Instructions ENGLISH Cooling Operation Mode 1 Press the on/off button.(or touch the anyplace of touch panel and touch the on/off key) TURBO-Z SET ROOM TEMP. ON/OFF PLASMA TURBO-Z 2 Select Cooling Operation. Press the Cooling Operation Button on the remote controller (or Touch the Cooling Operation key on the touch panel) SET TEMP. A/CL ON/OFF PLASMA TURBO-Z 3 Set the temperature lower than the room temperature. The temperature can be set within a range of 16°C~30°C by 1°C.
Operating Instructions Soft Dry Operation 1 Press the on/off button.(or touch the anyplace of touch panel and touch the on/off key) TURBO-Z SET ROOM TEMP. ON/OFF PLASMA TURBO-Z 2 Select Soft Dry Operation Press the Soft Dry Operation Button on the remote controller (or Touch the Soft Dry Operation key on the touch panel) SET TEMP. A/CL ON/OFF PLASMA TURBO-Z 3 Set the temperature lower than the room temperature. The temperature can be set within a range of 16°C~30°C by 1°C.
Operating Instructions ENGLISH Turbo-Z cooling Operation 1 Press the on/off button.(or touch the anyplace of touch panel and touch the on/off key) TURBO-Z SET ROOM TEMP. ON/OFF PLASMA TURBO-Z 2 Press the Turbo-Z Cooling button to operate the speed cooling mode and the unit will operate in super high fan speed on cooling mode.
Operating Instructions Heating Operation Mode(Heat Pump & Heater, Heat Pump Model) 1 Press the on/off button.(or touch the anyplace of touch panel and touch the on/off key) TURBO-Z SET ROOM TEMP. ON/OFF PLASMA TURBO-Z 2 Select Heating Operation Press the Heating Operation Button on the remote controller (or Touch the Heating Operation key on the touch panel.) SET TEMP. A/CL ON/OFF PLASMA TURBO-Z 3 Set the temperature upper than the room temperature.
Operating Instructions ENGLISH Electric Heater Operation Mode(Heater, Heat Pump Model) 1 Press the on/off button.(or touch the anyplace of touch panel and touch the on/off key) TURBO-Z SET ROOM TEMP. ON/OFF PLASMA TURBO-Z Select Heating + E/Heater Operation. the Heating & E/Heater Operation Button on the remote controller 2 Press (or Touch the heating & E/Heater Operation key on the touch panel) SET TEMP. A/CL A/CL ON/OFF PLASMA TURBO-Z 3 Set the temperature lower than the room temperature.
Operating Instructions Auto Operation Mode(Cooling Model Only) 1 Press the on/off button.(or touch the anyplace of touch panel and touch the on/off key) TURBO-Z SET ROOM TEMP. ON/OFF PLASMA TURBO-Z 2 Select Auto Operation Press the Auto Operation Button on the remote controller (or Touch the Auto Operation key on the touch panel) SET TEMP. A/CL ON/OFF PLASMA TURBO-Z 3 Set the temperature upper or lower than the standard temperature. The temperature can be set within a range of by 1 level.
Operating Instructions ENGLISH Energy Saving Mode(Cooling & Soft Dry Operation Only) 1 Press the on/off button.(or touch the anyplace of touch panel and touch the on/off key) TURBO-Z SET ROOM TEMP. ON/OFF PLASMA TURBO-Z the Energy Operation Button on the remote controller 2 Press (or Touch the Energy Saving Operation key on the touch panel) Select Energy Saving Operation TURBO-Z SET TEMP. ON/OFF PLASMA TURBO-Z 3 To cancel the Energy Saving mode.
Operating Instructions Airflow Direction Procedure 1 Press the on/off button (or touch the anyplace of touch panel and touch the on/off key) 2 TURBO-Z (Operation will start when the button is pressed, and stop when the button is pressed again. Press the Auto Swing Button and then louvers will swing Up and down. Press the Airflow Direction Control Button again to set the Horizontal louver at the desired airflow direction. A/CL The horizontal louver swing up and down.
Operating Instructions ENGLISH Plasma Air Purifying Operation Procedure 1 Air Purifying Operation only 1 Press(Touch) the Plasma Air Purifying Operation On/Off Button(Key). SET ROOM A/CL TEMP. ON/OFF PLASMA TURBO-Z (Operation will start when the button is pressed, and stop when the button is pressed again.) 2 The display shows low fan speed at the initial condition. Select Fan speed. TURBO-Z High TEMP.
Operating Instructions OFF Timer Setting Procedure(OFF TIMER Setting, or CANCEL) 1 Press the on/off button.(or touch the anyplace of touch panel and touch the on/off key) TURBO-Z SET ROOM ON/OFF TEMP. PLASMA TURBO-Z 2 Press the Timer Button. SET ROOM A/CL TEMP. ON/OFF PLASMA TURBO-Z • If you press the button, the selected off timer is displayed as follows; • If you select ʻ 3 ʼ, the Off Timer function will be cancelled.
Operating Instructions ENGLISH Child Lock Operation Procedure 1 Touched the fan speed and high temperature setting keys simultaneously for 3 seconds. The unit will respond with beep. ROOM TEMP. ON/OFF ROOM TEMP. TEMP. ROOM ON/OFF ON/OFF PLASMA PLASMA TURBO-Z TURBO-Z After 3 second, it will shift PLASMA TURBO-Z ROOM TEMP.
Maintenance and Service Maintenance and Service Indoor Unit WARNING: Turn the system off before cleaning. To clean, wipe with a soft, dry cloth. Do not use bleach or abrasives. NOTICE Supply power must be disconnected before cleaning the indoor unit. How to Clean Plasma Deodorant Air Cleaner At the smoking area, it is better to clean more than once in a month, otherwise in the other places, once in every 3 months will be good. Knob - For safety, unplug prior to cleaning. 1.
Maintenance and Service ENGLISH Filter Cleaning Please clean it once in a week. 1. Pull the knob of air inlet out. The antibiotic filter should be clean without disassembly as it is united with air inlet. Lift the front panel. After lifting up the filter tab a bit, take the filter out slowly 2. Clean it with the vacuum cleaner or brush off dust. When the contamination is serious, wash out with a neutral detergent (Do not use hot water over 40°C).
Maintenance and Service Common Problems and Solutions Before calling for service If you have problems with your air conditioner, read the following information and try to solve the problem. If you cannot find a solution, turn off the air conditioner and contact your dealer. Air conditioner does not operate 1. Ensure that the air conditioner is plugged into a proper outlet. 2. Check the fuse or circuit breaker. 3. Check whether the voltage is unusually high or low.
Maintenance and Service ENGLISH Troubleshooting The air conditioner may be operating abnormally when: Problem Air conditioner does not start Air conditioner does not cool as it should Air conditioner freezing up Possible Causes What To Do n The air conditioner is unplugged. • Make sure the air conditioner plug is pushed completely into the outlet. n The fuse is blown/circuit breaker is tripped. • Check the house fuse/circuit breaker box and replace the fuse or reset the breaker. n Power failure.
Memo 26 Floor Standing-Type Air Conditioner