website http://www.lgservice.com e-mail http://lgservice.com/techsup.html OWNER'S MANUAL FRANÇAIS LG Floor Standing Type Air Conditioner ENGLISH LG ESPAÑOL IMPORTANT • Please read this owner's manual carefully and thoroughly before installing and operating your air conditioner. • Please retain this owner's manual for future reference after reading it thoroughly.
Floor Standing- Type Air Conditioner Owner’s Manual TABLE OF CONTENTS FOR YOUR RECORDS Safety Precautions.................3 Write the model and serial numbers here: Model # Serial # Operating Instructions...........9 You can find them on a label on the side of each unit. Dealer's Name Date Purchased Maintenance and Service ....25 ■ Staple your receipt to this page in the event you need it to prove date of purchase or for warranty issues. Celsius(°C) ↔ Fahrenheit (°F) Convert Table ...................
Safety Precautions Safety Precautions WARNING This symbol indicates the possibility of death or serious injury. CAUTION This symbol indicates the possibility of injury or damage. ■ Meanings of symbols used in this manual are as shown below. Be sure not to do. Be sure to follow the instruction. WARNING ■ Installation Do not use a defective or underrated circuit breaker. Use this appliance on a dedicated circuit. • There is risk of fire or electric shock.
Safety Precautions Do not modify or extend the power cable. • There is risk of fire or electric shock. For installation, always contact the dealer or an Authorized Service Center. • There is risk of fire, electric shock, explosion, or injury. Do not install, remove, or reinstall the unit by yourself (customer). • There is risk of fire, electric shock, explosion, or injury. Do not install the product on a defective installation stand. • It may cause injury, accident, or damage to the product.
Safety Precautions Do not allow water to run into electric parts. • There is risk of fire or failure of product. Do not use the product in a tightly closed space for a long time. • Oxygen deficiency could occur. ENGLISH • It may cause There is risk of fire, failure of the product, or electric shock. Do not store or use flammable gas or combustibles near the product. Gasolin When flammable gas leaks, turn off the gas and open a window for ventilation before turn the product on.
Safety Precautions When the product is not be used for a long time, disconnect the power supply plug or turn off the breaker. • There is risk of product damage or failure, or unintended operation. Take care to ensure that nobody could step on or fall onto the outdoor unit. • This could result in personal injury and product damage. CAUTION ■ Installation Always check for gas (refrigerant) leakage after installation or repair of product. • Low refrigerant levels may cause failure of product.
Safety Precautions Use a soft cloth to clean. Do not use harsh detergents, solvents, etc. • It may cause product failure. • There is risk of fire, electric shock, or damage to the plastic parts of the product. Do not touch the metal parts of the product when removing the air filter. They are very sharp! • There is risk of personal injury. ENGLISH Do not block the inlet or outlet of air flow. x Wa Thinner Do not step on or put anyting on the product. (outdoor units) Always insert the filter securely.
Prior to Operation Prior to Operation Preparing for Operation 1. Contact an installation specialist for installation. 2. Plug in the power plug properly. 3. Use a dedicated circuit. 4. Do not use an extension cord. 5. Do not start/stop operation by plugging/unplugging the power cord. 6. If the cord/plug is damaged, replace it with only an authorized replacement part. Usage 1. Being exposed to direct airflow for a long time may be hazardous to your health.
Operating Instructions Operating Instructions Features and Specifications ENGLISH 1. 3D Stereo Cooling This first developed 3D Stereo Cooling Method makes clear a dead zone to cool the indoor evenly within a early time. 7. Whisper quiet operation 8. Wireless remote control 9. 3 cooling speeds 10. Removable air filter 11. Anti-Bacteria filter 12. 3 minutes delay circuit 13. Turbo-Z operation 14. Energy saving 15. Auto restart 16. Plasma Air Purifying system 2.
Operating Instructions Indoor Unit Controls and Indicators 1 2 8 12 3 4 5 13 6 14 9 10 11 15 7 16 1. Air Cleaner Operation Display 10. Outdoor Unit Operation Display 2. Energy Saving Operation Display 11. Off Timer Operation Display 3. Cooling Operation Display 12. Air Cleaner Operation Key 4. Auto Operation Display 13. Indoor Fan Speed Key 5. Soft Dry Operation Display Used to select fan speed in three steps-low, High, Super High. 6. Power on Display 14.
Operating Instructions Features of the Remote Control- Door Closed START/STOP BUTTON 2 ROOM TEMPERATURE SETTING BUTTONS Operation starts when this button is pressed and stops when the button is pressed again. Used to select the room temperature. 4 5 3 1 3 INDOOR FAN SPEED SELECTOR Used to select fan speed in three steps low, high, super high. 2 4 TURBO-Z 5 AUTO AIRFLOW DIRECTION CONTROL BUTTON Flip-up door (closed) Used to start or stop the speed cooling.
Operating Instructions Features of the Remote Control- Door Opened ON OFF 1 4 2 5 SET ON/OFF TIMER BUTTONS 2 TIME SETTING BUTTONS 3 TIMER SET/CANCEL BUTTONS 4 SIMPLE OFF TIMER SET BUTTON 6 9 8 Used to set the time of starting and stopping operation. Used to adjust the time. Used to set the timer when the desired time is obtained and to cancel the Timer operation. Each time the button is pressed, the mode is changed in the following process.
Operating Instructions Remote Control Preparation Use the screws to secure the holder to the wall or attach the holder side of indoor unit. • Please keep it on the right side of indoor unit. When opening When closing 2. To insert the remote control to the holder. Insert Pull How to insert batteries 1. Remove the cover from the back of the remote controller. • Slide the cover according to the arrow direction.
Operating Instructions Cooling Operation Mode 1 2 3 Press the on/off button.(or touch anyplace of touch panel and touch the on/off key) Select Cooling Operation. Press the mode Operation Button on the remote controller (or Touch the mode Operation key on the touch panel) ON OFF SET CANCEL Set the temperature lower than the room temperature. The temperature can be set within a range of 60°F~86°F by 1°F. To raise the temperature To lower the temperature 4 When you finish the temperature setting.
Operating Instructions Soft Dry Operation 2 3 Press the on/off button.(or touch the anyplace of touch panel and touch the on/off key) Select Soft Dry Operation Press the mode Operation Button on the remote controller (or Touch the mode Operation key on the touch panel) ON OFF SET CANCEL Set the temperature lower than the room temperature. The temperature can be set within a range of 60°F~86°F by 1°F. To raise the temperature To lower the temperature 4 When you finish the temperature setting.
Operating Instructions TURBO-Z Operation Press the on/off button.(or touch the anyplace of touch panel and touch the on/off key) 1 2 Press the TURBO-Z button to operate the speed cooling mode and the unit will operate in super high fan speed in cooling mode. 3 To cancel the TURBO-Z mode, press the TURBO-Z button again or the Auto Swing Direction Control Button (Up & Down, Left & Right) or Operation Mode Button and the unit will operate in High. Fan speed on cooling mode.
Operating Instructions Auto Operation Mode ENGLISH 1 Press the on/off button.(or touch the anyplace of touch panel and touch the on/off key) Select Auto operation mode the Mode Operation Button on the remote controller 2 Press (or Touch the Mode Operation key on the touch panel) 3 ON OFF SET CANCEL Set the temperature upper or lower than the standard temperature. The temperature can be set within a range of by 1 level.
Operating Instructions Energy Saving Mode 1 Press the on/off button.(or touch the anyplace of touch panel and touch the on/off key) Select Energy Saving Operation the Energy Operation Button on the remote controller 2 Press (or Touch the Energy Saving Operation key on the touch panel) ON OFF SET CANCEL To cancel the Energy Saving mode. Press(Touch) the Energy Saving Button(Key) Again 3 and the unit will operate on Cooling/Auto/Soft Dry mode.
Operating Instructions Airflow Direction Procedure Press the on/off button (or touch the anyplace of touch panel and touch the on/off key) (Operation will start when the button is pressed, and stop when the button is pressed again. 2 Press the Auto Swing Button and then louvers will swing Up and down. Press the Airflow Direction Control Button again to set the Horizontal louver at the desired airflow direction. The horizontal louver swing up and down.
Operating Instructions Plasma Air Purifying Operation Procedure 1 Air Purifying Operation only 1 Press(Touch) the Plasma Air Purifying Operation. ON OFF SET CANCEL (Operation will start when the button is pressed, and stop when the button is pressed again.) Fan speed. 2 Select The display shows low fan speed at the initial condition. Low High • You can operate the Plasma Air Purifying under the unit operation of cooling, soft dry or Auto operation mode.
Operating Instructions OFF Timer Setting Procedure(OFF TIMER Setting, or CANCEL) 2 Press the on/off button.(or touch the anyplace of touch panel and touch the on/off key) Press the Timer Button. ON OFF SET CANCEL • If you press the button, the selected off timer is displayed as follows; • If you select ‘ 3 ’, the Off Timer function will be cancelled. When you finish the Off Timer setting, the Timer indicator lights off.
Operating Instructions ˚C ↔ ˚F switching button 1 2 Press the on/off button.(or touch the anyplace of touch panel and touch the on/off key) Touch the fan speed and on/off keys simultaneously for 3 seconds. The unit will respond with beep. After 4 seconds 3 ˚C ↔ ˚F switching button ON OFF SET CANCEL Auto restart In case the power comes on again after a power failure, Auto Restarting Operation is the function to operate procedures automatically to the previous operating conditions.
Operating Instructions Child Lock Operation Procedure After 3 second, it will shift After 3 second, it will shift During Child Lock Operation 2 ➊ Whenever you Touch any key on Touch panel, it will immediately display “ ”, which means Touch panel is Locked. ❷ All the key on the indoor unit Touch panel will not work. ❸ But the key on the remote controller will work. For releasing child lock Operation 3 Touched the fan speed and high temperature setting keys simultaneously for 3 seconds again.
Operating Instructions Additional features Setting the Time 1 Time can be set only when you have pressed the Reset button. If you have just replaced the batteries, the Reset button should be pressed to reset the time. 2 Press the Time Setting buttons until the desired time is set. Press the Start/Stop button. 3 Press the Timer SET button. SET Note: Check the indicator for A.M. and P.M. Delay Start/Pre-Set Stop 1 Make sure the time is set correctly on the remote control display.
Maintenance and Service Maintenance and Service Indoor Unit NOTICE Supply power must be disconnected before cleaning the indoor unit. How to Clean Plasma Deodorant Air Cleaner At the smoking area, it is better to clean more than once in a month, otherwise in the other places, once in every 3 months will be good. Knob - For safety, unplug prior to cleaning. 1. Pull out the knob of air inlet. The antibiotic filter should be clean without disassembly as it is united with air inlet. Air Inlet 2.
Maintenance and Service Filter Cleaning Please clean it once in a week. 1. Pull the knob of air inlet out. The antibiotic filter should be clean without disassembly as it is united with air inlet. Lift the front panel. After lifting up the filter tab a bit, take the filter out slowly 2. Clean it with the vacuum cleaner or brush off dust. When the contamination is serious, wash out with a neutral detergent (Do not use hot water over 104°F).
Maintenance and Service Common Problems and Solutions If you have problems with your air conditioner, read the following information and try to solve the problem. If you cannot find a solution, turn off the air conditioner and contact your dealer. Air conditioner does not operate 1. Ensure that the air conditioner is plugged into a proper outlet. 2. Check the fuse or circuit breaker. 3. Check whether the voltage is unusually high or low. Air does not feel cold enough on the cooling setting 1.
Maintenance and Service Troubleshooting The air conditioner may be operating abnormally when: Problem Air conditioner does not start Air conditioner does not cool as it should Air conditioner freezing up Possible Causes What To Do ■ The air conditioner is unplugged. • Make sure the air conditioner plug is pushed completely into the outlet. ■ The fuse is blown/circuit breaker is tripped. • Check the house fuse/circuit breaker box and replace the fuse or reset the breaker. ■ Power failure.
Celsius(°C) ↔ Fahrenheit (°F) Convert Table Celsius(°C) ↔ Fahrenheit (°F) Convert Table °F 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 °C 26 26 27 27 28 28 29 29 30 31 31 32 32 33 33 34 34 35 36 36 37 37 38 38 39 39 40 41 41 42 42 43 43 44 44 45 46 46 47 47 48 48 49 49 50 °F 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 1
Memo 30 Floor Standing-Type Air Conditioner