User’s Guide L1982U Make sure to read the Important Precautions before using this product. Keep the User's Guide (CD) in an accessible place for future reference. See the attached label on the unit and show this information to your dealer when asking for service.
Important Precautions This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing. On Safety Use only the power cord supplied with the unit.
Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord, and do not place the display where the power cord is subject to damage. Do not use this display near water such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. Displays are provided with ventilation openings in the cabinet to allow the release of heat generated during operation.
Connecting the Display Unfolding the stand base 1. Put your monitor on a table. Do not hold the stand base as shown in this picture. 2. Hold the monitor as shown, and then lift it up slightly. 3. Hold the head part of the monitor and pull it toward you. 4. Place the monitor upright and adjust the The Head part stand base to the desired angle. Adjust the stand base's angle by holding the edges of the monitor gently with both hands. This illustration depicts the typical connection procedure.
Connecting the Display Folding the stand base 1. Face the front of the monitor dislpay. Than gently push the monitor backwards, following the sequence shown in the picture below. Tilt range 1. Make sure that the angle of the panel is set for your comfort. NOTE When the panel is tilted at more than 30˚, you cannot adjust the height of the monitor.
Connecting the Display To adjust the height, ● Height Range : maximum 2.36 inches (60 mm) 60mm NOTE When the monitor is at maximum height, it may slide down slightly due to the elasticity of the spring.
Connecting the Display Connecting with the PC 1. Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. 2. Connect the signal cable ① . After it is attached, tighten the thumbscrews to secure the connection. 3. Connect the power cable ➂ to the AC-DC adapter (AC-DC power supply) ② , and then plug the cable into the outlet. NOTE This is a simplified representation of the rear view.
Using the Auto Pivot and Auto Mirror functions This model supports Auto Pivot (automatic rotation) and Auto Mirror (automatic up/down reverse) functions. To use these functions, first install the provided Forte Manager software, and then set to Automatic.(Manual is the default setting when you initially purchase the product.) - Refer to the installation guide, which is included on the CD for more details on the installation -To set to Automatic, select Forte Manager -> Option -> Pivot -> Enable Auto Pivot.
Using the Auto Pivot and Auto Mirror functions Tilt the screen while rotating it so that the monitor does not touch the floor. Do not hold the screen area as shown in the picture when rotating it, otherwise your fingers might get hurt or get stuck. Auto Mirror Screen switch : The monitor screen is automatically reversed when you switch it forward/backward as shown in the figure.
Control Panel Functions Front Panel Controls Bottom Control Function MENU Button Use this button to enter or exit from the On Screen Display. OSD LOCKED/UNLOCKED This function allows you to lock the current control settings, so that these settings are not inadvertently changed. To lock the OSD settings, press and hold the MENU button for several seconds. The message "OSD LOCKED" appears. You can unlock the OSD settings at any time by pushing the MENU button for several seconds.
Control Panel Functions Control AUTO/SET Button Function Use this button to selection an icon in the On Screen Display. AUTO IMAGE ADJUSTMENT When adjusting your display settings, always press the AUTO/SET button prior to entering the On Screen Display(OSD). This will automatically adjust your display image to the ideal settings for the current screen resolution size (display mode). The best display mode is 1280 x 1024 Power Button Use this button to turn the display on or off.
On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the display's image size, position and operating parameters is quick and easy with the On Screen Display Control system(OSD). A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make by using the OSD. NOTE Allow the display to stabilize for at least 30 minutes before making any image adjustments.
On Screen Display (OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus.
On Screen Display (OSD) Selection and Adjustment Earlier you were introduced to the procedure for selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of every items that displays on the Menu. Press the MENU Button, then the main menu of the OSD appears.
On Screen Display (OSD) Selection and Adjustment Main menu Sub menu Description PICTURE PICTURE BRIGHTNESS To adjust the brightness of the screen. CONTRAST To adjust the contrast of the screen. GAMMA Set your own gamma value. : -50/0/50 on the monitor, high gamma values display whitish images and low gamma values display high contrast images.
On Screen Display (OSD) Selection and Adjustment Main menu Sub menu Description TRACKING TRACKING CLOCK To minimize any vertical bars or stripes visible on the screen background. This also allows you horizontal screen size. PHASE To adjust the focus of the display. This item allows you to remove any horizontal noise and clear or sharpen the image of characters. MENU : Exit - : Decrease SHARPNESS To adjust the clarity of the screen.
On Screen Display (OSD) Selection and Adjustment The OSD screen will appear when you press the right side of the monitor. (-) button on the Menu Name Icons Sub-menu Name FLATRON F-ENGINE Screen when applied Screen when not applied When you execute F-ENGINE, two tone will appear on the screen as shown in the picture. The applied screen will appear on the left side, whereas the nonapplied screen will appear on the right side.Press the SET button to use the adjusted screen.
Troubleshooting Check the following before calling for service. No image appears ● Is the power cord of the • Check and see if the power cord is connected properly to the power outlet. display connected? ● Is the power on and the • Adjust the brightness and the contrast. power indicator blue or green? ● Is the power indicator amber? • If the display is in power saving mode, move the mouse or press any key on the keyboard to activate the screen. • Turn on the PC.
Troubleshooting Display image is incorrect ● Display Position is incorrect. • Press the AUTO/SET button to automatically adjust the display image to the ideal setting. If the results are unsatisfactory, adjust the image position using the H position and V position icon on the On Screen Display. • Check Control Panel --> Display --> Settings and see if the frequency or the resolution were changed. If yes, readjust the video card to the recommended resolution.
Troubleshooting Have you installed the display driver? ● Have you installed the display driver? • Be sure to install the display driver from the display driver CD (or diskette) that comes with your Monitor. Or, you can also download the driver from our web site: http://www.lge.com. ● Do you see an "Unrecognized monitor, Plug&Play (VESA DDC) monitor found" message? • Make sure to check if the video card supports the Plug&Play function.
Specifications Display 19 inches (48.19 cm) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 48.19 cm 0.294 mm pixel pitch Sync Input Horizontal Freq. Vertical Freq.
Specifications Tilt Stand Power cord Attached ( O ), Detached ( ) Wall-outlet type or PC-outlet type NOTE Information in this document is subject to change without notice.
Specifications Preset Modes (Resolution) Display Modes (Resolution) 1 2 3 4 5 6 7 8 9 10 11 *12 **13 VGA VGA VGA VESA VESA VESA MAC VESA VESA MAC VESA VESA VESA Horizontal Freq. (kHz) Vertical Freq. (Hz) 31.469 31.468 31.469 37.500 37.879 46.875 49.725 48.363 60.023 68.681 61.805 63.981 79.
Specifications Kensington Security Slot Connected to a locking cable that can be purchased separately at most computer stores.
Digitally yours
