User’s Guide L200ME Make sure to read the Safety Precautions before using the product. Keep the User's Guide(CD) in an accessible place for furture reference. See the label attached on the product and give the information to your dealer when you ask for service.
Safety Precautions Please read these safety precautions carefully before using the product. Warning Failure to follow those warnings may result in death, serious injury or damage to the product or other property. Electrical Power Related Precautions Warning Use only the power cord supplied with the unit or another manufacturer authorized cord. - Failure to do so may result in fire or electrical shock or damage to the product. Use only a properly grounded plug and receptacle.
Safety Precautions Keep the packing anti-moisture material or vinyl packing out of the reach of children. - Anti-moisture material is harmful if swallowed. If swallowed by mistake, force the patient to vomit and visit the nearest hospital. Additionally, vinyl packing can cause suffocation. Keep it out of the reach of children. Do not put heavy objects on the product on sit upon it. - If the product collapses or is dropped, you may be injured. Children must pay particular attention.
Safety Precautions Precautions in Using/Cleaning the Product Warning Do not attempt to disassemble, repair or modify the product yourself. - Fire or electric shock can occur. - Contact the service center for repair. When cleaning the product, unplug the power cord and scrub gently with a soft cloth to prevent scratching. Do not clean with a wet cloth. Or spray water or other liquids directly onto the product. An electric shock may occur.
Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Connecting the stand base or Removing the stand base 1. Place the monitor with its front facing downward on a cushion or soft cloth. 2. Rotate the Stand Body as shown in figure 1 . 1 3. Align the hooks on the stand base with the matching slots in the base of the monitor. 4. Insert the hooks into slots.
Connecting the Display 5. Attach the monitor to the Stand Base by turning the screw to the right. 6. Lift and turn the monitor to face towards the front after the connection is made to the female part of the cable you're attaching. 7. Take the screw out by turning to the left to separate the monitor and Stand Base. Screw : Turn the screw by using the screw handle. Important This illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture.
Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -5˚~20˚ Swivel Range : 350˚ Height Range : maximun 3.94 inch (100.0mm) 100.0 mm * Please be sure to remove the Locking pin to adjust the height. Notice You do not need to replace the Locking pin after it is removed, to adjust its height.
Connecting the Display Using the Pivot function 1. Lift the monitor to its highest height to utilize the Pivot function. 2. Landscape & Portrait : You can rotate the panel 90 o clockwise. Please be cautious and avoid contact between the monitor head and the Stand Base when rotating the screen to access the Pivot function. If the monitor head touches the Stand Base, then the Stand Base could crack. Head section Stand section 3. For detailed information, please refer to the Pivot Software CD provided.
Connecting the Display Using the Computer 1. Place the monitor in a convenient, well-ventilated location near your computer. To adjust height of your monitor, unlock the stand lock on top of the stand. 2. Connect the signal cable. When attached, tighten the thumbscrews to secure the connection. 1 3. Connect the power cord into a proper power outlet that is easily accessible and close to the display. 2 Signal Cable Power Cord Digital signal Analog signal DVI D-sub Varies according to model.
Connecting to External Devices To arrange the cables Connect the power cord and the signal cable as shown in the figure and then fix them to the cable holders 1 and 2. 1. Please insert the cable holder 1 2. Please put the power cord and the into the hole. signal cable in the cable holder 1. Cable Holder1 3. Please put the power cord and the signal cable in the cable holder 2. While pressing the bottom of cable holder 2 with one hand, pull the top of it with the other hand as shown in the picture.
Control Panel Functions Front Panel Controls Control Function MENU Button Use this button to enter or exit the On Screen Display. OSD LOCKED/UNLOCKED This function allows you to lock the current control settings, so that they cannot be inadvertently changed. Press and hold the MENU button for several seconds. The message "OSD LOCKED" should appear. You can unlock the OSD controls at any time by pushing the MENU button for several seconds. The message "OSD UNLOCKED" should appear.
Control Panel Functions Control AUTO/SET Button Function Use this button to enter a selection in the On Screen Display. AUTO IMAGE ADJUSTMENT When adjusting your display settings, always press the AUTO/SET button before entering the On Screen Display(OSD). This will automatically adjust your display image to the ideal settings for the current screen resolution size (display mode). The best display mode is 1600x1200 Power Button Use this button to turn the display on or off.
On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make using the OSD. NOTE Allow the display to stabilize for at least 30 minutes before making image adjustments.
On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus.
On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Press the MENU Button, then the main menu of the OSD appears.
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description PICTURE PICTURE BRIGHTNESS To adjust the brightness of the screen. CONTRAST To adjust the contrast of the screen. GAMMA Set your own gamma value. : -50/0/50 On the monitor, high gamma values display whitish images and low gamma values display high contrast images.
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description TRACKING TRACKING CLOCK To minimize any vertical bars or stripes visible on the screen background.The horizontal screen size will also change. PHASE To adjust the focus of the display. This item allows you to remove any horizontal noise and clear or sharpen the image of characters.
On Screen Display(OSD) Selection and Adjustment The OSD screen will appear when you touch the AAA (-) button on the right side of the monitor. Menu Name Icons Sub-menu Name FLATRON F-ENGINE Screen when applied Screen when not applied When you execute F-ENGINE, two tones will appear on the screen as shown. The applied screen will appear on the left side, whereas the non-applied screen will appear on the right side.Touch the SET button to use the adjusted screen.
Troubleshooting Check the following before calling for service. No image appears Is the power cord of the display connected? Check and see if the power cord is connected properly to the power outlet. Is the power on and the power indicator blue or green? Adjust the brightness and the contrast. Is the power indicator amber? If the display is in power saving mode, try moving the mouse or pressing any key on the keyboard to bring up the screen. Try to turn on the PC.
Troubleshooting Display image is incorrect Display Position is incorrect. Press the AUTO/SET button to automatically adjust your display image to the ideal setting. If the results are unsatisfactory, adjust the image position using the H position and V position icon in the on screen display. Check Control Panel --> Display --> Settings and see if the frequency or the resolution were changed. If yes, readjust the video card to the recommend resolution.
Troubleshooting Have you installed the display driver? Have you installed the display driver? Be sure to install the display driver from the display driver CD (or diskette) that comes with your display. Or, you can also download the driver from our web site: http://www.lge.com. Do you see an "Unrecognized monitor, Plug&Play (VESA DDC) monitor found" message? Make sure to check if the video card supports Plug&Play function.
Specifications Display TFT (Thin Film Transistor) LCD (Liquid Crystal Display) Panel Anti-Glare coating 20.1inches visible diagonal (51.0cm) 0.255mm pixel pitch Sync Input Horizontal Freq. Vertical Freq. Input Form 28 - 83kHz (Automatic) 56 - 85Hz (Automatic) Separate Sync, Composite Sync SOG (Sync On Green) Digital Video Input Signal Input Input Form 15 pin D-Sub Connector DVI - D connector (Digital) RGB Analog (0.
Specifications Preset Modes (Resolution) Display Modes (Resolution) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 *17 **18 Horizontal Freq. (kHz) 31.47 31.47 37.50 43.27 31.47 37.88 46.88 53.67 49.72 48.36 60.02 68.68 68.68 61.80 63.98 79.98 75.00 73.53 640 x 350 640 x 480 640 x 480 640 x 480 720 x 400 800 x 600 800 x 600 800 x 600 832 x 624 1024 x 768 1024 x 768 1024 x 768 1152 x 870 1152 x 900 1280 x 1024 1280 x 1024 1600 x 1200 1600 x 1200 Vertical Freq. (Hz) 70 60 75 85 70 60 75 85 75 60 75 85 75 65.
How to Install the VESA Standard wall mounting This monitor meets VESA-compliant mounting interface pad specifications. 1. After moving the product to face downward, make sure to place it on a soft cloth or a cushion to avoid surface damage. 2. Separate the head and the stand with the use of a screwdriver. 3. Set up the VESA standard Stand Base. VESA wall mounting Connected to another object (stand type and wall-mounted type. This monitor accepts a VESA-compliant mounting interface pad.
Digitally yours