OWNER’S MANUAL LCD TV Please read this manual carefully before operating your set and retain it for future reference. 26LD320H 32LD320H 37LD320H 42LD320H 32LD325H 37LD325H 26LD340H 32LD340H 37LD340H 42LD340H 26LD345H 32LD345H 37LD345H 42LD345H 32LD310H 37LD310H 32LD330H 37LD330H The model and serial number of the TV is located on the back and one side of the TV. Record it below should you ever need service. MODEL SERIAL P/NO : SAC34026009 (1106-REV05) www.lg.
WARNING WARNING To prevent fire or shock hazards, do not expose this product to rain or moisture. TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS Read these instructions. Keep these instructions. 10 Heed all warnings. Follow all instructions. 1 Do not use this apparatus near water. 2 Clean only with dry cloth. 3 Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 4 Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
SAFETY INSTRUCTIONS 15 WARNING - To reduce the risk of fire or electrical shock, do not expose this product to rain, moisture or other liquids. Do not touch the TV with wet hands. Do not install this product near flammable objects such as gasoline or candles or expose the TV to direct air conditioning. 16 Do not expose to dripping or splashing and do not place objects filled with liquids, such as vases, cups, etc. on or over the apparatus (e.g. on shelves above the unit).
28 Dot Defect The Plasma or LCD panel is a high technology product with resolution of two million to six million pixels. In a very few cases, you could see fine dots on the screen while you’re viewing the TV. Those dots are deactivated pixels and do not affect the performance and reliability of the TV. 29 Generated Sound “Cracking” noise: A cracking noise that occurs when watching or turning off the TV is generated by plastic thermal contraction due to temperature and humidity.
CONTENTS WARNING...........................................................2 SAFETY INSTRUCTIONS......................... 3 FEATURE OF THIS TV...............................8 PREPARATION Accessories..............................................................9 Front Panel Information.....................................10 Back Panel Information....................................... 11 Stand Instructions................................................ 14 VESA wall mounting..................................
TIME SETTING Clock Setting - Auto Clock Setup............................................85 - Manual Clock Setup.......................................86 Auto On/Off Time Setting............................... 87 Sleep Timer Setting...........................................88 Auto Shut-Off Setting.......................................88 PARENTAL CONTROL / RATINGS Set Password & Lock System - Setting up Your Password.............................89 - Set Password............................................
FEATURE OF THIS TV ꔛ Some of these features are not available on all models. High-definition television. Highresolution digital television broadcast and playback system composed of roughly a million or more pixels, 16:9 aspect-ratio screens, and AC3 digital audio. A subset of digital television, HDTV formats include 1080i and 720p resolutions. A unique invisible speaker system tuned by renowned audio expert, Mr. Mark Levinson.
PREPARATION ACCESSORIES Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the dealer where you purchased the TV. The accessories included may differ from the images below. Owner’s Manual 1,5Vcc 1,5Vcc 1.5V 1.5V CD Manual PREPARATION 1.5V 1.5V 1,5Vcc 1,5Vcc Remote Control, Batteries (AAA) Protection Cover (Refer to P.15) Screw for stand fixing (Refer to P.19) Protective Bracket and 1.5V 1.5V Screw for Power Cord (Refer to P.
PREPARATION FRONT PANEL INFORMATION ꔛ Image shown may differ from your TV.
BACK PANEL INFORMATION AC IN Image shown may differ from your TV.
PREPARATION 32/37LD310H PREPARATION 1 6 2 4 5 11 RS-232C IN (SERVICE ONLY) RESET UPDATE REMOTE CONTROL OUT 2 AUDIO IN (RGB/DVI) /DVIIN 1 AV IN 1 VIDEO ANTENNA IN M.P.I. 14 15 L/MONO AUDIO R RGB IN (PC) SPEAKER OUT (8 ) Y PB L PR VIDEO AUDIO R COMPONENT IN 7 3 32/37LD330H 1 6 2 4 5 11 RS-232C IN (SERVICE ONLY) RESET UPDATE REMOTE CONTROL OUT 2 AUDIO IN (RGB/DVI) /DVIIN 1 ANTENNA IN AV IN 1 VIDEO L/MONO AUDIO R M.P.I.
AC IN 2 12 5 11 14 4 RS-232C IN (SERVICE ONLY) RESET UPDATE RJP REMOTE CONTROL OUT 2 /DVIIN 1 AUDIO IN (RGB/DVI) ANTENNA IN AV IN 1 VIDEO L/MONO AUDIO R GAME CONTROL/ TV - LINK M.P.I. CFG RGB IN (PC) SPEAKER OUT (8 ) Y PB VIDEO PR L AUDIO VIDEO L/MONO AUDIO R 6 PREPARATION 1 USB IN 26LD320H, 26LD340H, 26LD345H AV IN 2 R COMPONENT IN 3 1 2 3 4 5 6 7 HDMI/DVI IN, HDMI IN Digital Connection. Supports HD video and Digital audio. Doesn’t support 480i.
PREPARATION STAND INSTRUCTIONS ꔛ Image shown may differ from your TV. PREPARATION INSTALLATION 1 Carefully place the TV screen side down on a cushioned surface to protect the screen from damage. AC IN CABLE MANAGEMENT AC IN CABLE MANAGEMENT 2 Assemble the parts of the STAND BODY with the STAND BASE of the TV. (Except 32/37LD310H, 32/37LD330H) STAND BODY M4X20 M4 x 24 STAND BASE 3 Assemble the TV as shown.
ꔛ Image shown may differ from your TV. PREPARATION DETACHMENT Carefully place the TV screen side down on a cushioned surface to protect the screen from damage. 1 AC IN CABLE MANAGEMENT AC IN 2 Remove the screws from the TV. AC IN AC IN CABLE MANAGEMENT AC IN CABLE MANAGEMENT CABLE MANAGEMENT 3 Detach the stand from TV.
PREPARATION VESA WALL MOUNTING PREPARATION Install your wall mount on a solid wall perpendicular to the floor. When attaching to other building materials, please contact your nearest installer. If installed on a ceiling or slanted wall, it may fall and result in severe personal injury. We recommend that you use an LG brand wall mount when mounting the TV to a wall. LG recommends that wall mounting be performed by a qualified professional installer.
CABLE MANAGEMENT ꔛ Image shown may differ from your TV. Connect the cables as necessary. To connect additional equipment, see the EXTERNAL EQUIPMENT SETUP section. Secure the power cord with the PROTECTIVE BRACKET/SCREW or the POWER CORD HOLDER. It will help prevent the power cable from being removed by accident. PREPARATION 1 or PROTECTIVE BRACKET/SCREW 2 POWER CORD HOLDER Install the CABLE MANAGEMENT CLIP as shown. If your TV has the CABLE HORDER, install it as shown and bundle the cables.
PREPARATION DESKTOP PEDESTAL INSTALLATION ꔛ Image shown may differ from your TV. For proper ventilation, allow a clearance of 10.1 cm (4 inch) on all four sides from the wall. PREPARATION 10.1 cm (4 inch) ! ! ? ? 10.1 cm (4 inch) 10.1 cm (4 inch) 10.1 cm (4 inch) CAUTION ► Ensure adequate ventilation by following the clearance recommendations. ► Do not mount near or above any type of heat source.
ATTACHING THE TV TO A DESK ꔛ Image shown may differ from your TV. Stand PREPARATION The TV must be attached to a desk so it cannot be pulled in a forward/backward direction, potentially causing injury or damaging the product.
PREPARATION PREPARATION 32/37LD310H, 32/37LD330H Stand 4-Screws (not provided as parts of the product) ! ! ? ? Desk ► Screw: M5 x L (*L: Table depth + 8~10 mm) ex) Table depth: 15mm, Screw: M5 x 25 WARNING ► To prevent TV from falling over, the TV should be securely attached to the floor/wall per installation instructions. Tipping, shaking, or rocking the machine may cause injury.
SECURING THE TV TO THE WALL TO PREVENT FALLING WHEN THE TV IS USED ON A STAND ꔛ We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards. Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction, potentially causing injury or damaging the product. Caution: Please make sure that children don’t climb on or hang from the TV.
IN 4 ꔛ ANTENNA OR CABLE CONNECTION Multi-family Dwellings/Apartments ꔡ (Connect to wall antenna socket) WIRELESS 1 RS-232C IN IN 4 IN (PC) Wall Antenna Socket or Outdoor Antenna without a Cable RGB Box Connections. 3 LAN RGB/DVI OPTICAL DIGITAL For optimum picture quality, adjust antenna direction if2 needed.
EXTERNAL EQUIPMENT SETUP ꔛ To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment. ꔛ This part of EXTERNAL EQUIPMENT SETUP mainly use picture of for 32/37/42LD320H. HD RECEIVER SETUP This TV can receive digital over-the-air/digital cable signals without an external digital set-top box. However, if you do receive digital signals from a digital set-top box or other digital external device. Component Connection EXTERNAL EQUIPMENT SETUP 1.
RESET UPDATE EXTERNAL EQUIPMENT SETUP RJP RS-232C IN (SERVICE ONLY) REMOTE CONTROL OUT 2 /DVI IN 1 AV IN VIDEO L(MONO) AUDIO R AUDIO IN (RGB/DVI) RGB IN (PC) SPEAKER OUT (8 ) Y PB PR VIDEO L AUDIO R COMPONENT IN HDMI Connection 1. How to connect 1 EXTERNAL EQUIPMENT SETUP RJP RS-232C IN (SERVICE ONLY) RESET UPDATE No separate audio connection is necessary. HDMI supports both audio and video. 2 /DVIIN 2 REMOTE CONTROL OUT 1 AUDIO IN (RGB/DVI) RGB IN (PC) SPEAKER OUT (8 ) Y 2.
OUT (8 ) Y RS-232C IN REMOTE CONTROL OUT AUDIO IN (RGB/DVI) Y L AUDIO R AV IN 1 VIDEO L/MONO AUDIO R GAME CONTROL RGB IN (PC) SPEAKER OUT(8 ) PR COMPONENT IN (SERVICE ONLY) RJP PB VIDEO PB VIDEO PR L AUDIO TV - LINK CFG HDMI OUTPUT R COMPONENT IN DVI to HDMI Connection 1. How to connect RJP RS-232C IN (SERVICE ONLY) RESET UPDATE 2 Connect the DVI output of the digital set-top box to the HDMI/DVI IN 1 jack on the TV.
EXTERNAL EQUIPMENT SETUP DVD SETUP Component Connection 1. How to connect EXTERNAL EQUIPMENT SETUP 1 Connect the video outputs (Y, PB, PR) of the DVD to the COMPONENT IN VIDEO jacks on the TV. Match the jack colors (Y = green, PB = blue, and PR = red). 2 Connect the audio outputs of the DVD to the COMPONENT IN AUDIO jacks on the TV. RESET UPDATE 2. How to use ꔛ ꔛ ꔛ Turn on the DVD player, insert a DVD. /DVI IN Select the Component input source on the TV using the INPUT button on the remote control.
OPTICAL AUDIO IN DIGITAL RGB/DVI AUDIO OUT RGB IN (PC) Y PB PR VIDEO L AUDIO R ANTENNA/ CABLE IN COMPONENT IN Composite (RCA) Connection RS-232C IN (SERVICE ONLY) TE ROL IN VI) DEO HDMI OUTPUT 1. How to connect AV IN 1 VIDEO L/MONO AUDIO R 1 L PR COMPONENT IN AUDIO GAME Connect the AUDIO/VIDEO jacks between TV CONTROL TV - LINK CFG and DVD. Match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red) R 2.
EXTERNAL EQUIPMENT SETUP VCR SETUP 1 (DVI) DC-IN 2 /DVI IN DC-IN /DVI IN Antenna Connection 1 (DVI) 1. How to connect EXTERNAL EQUIPMENT SETUP 1 2 RS-232C IN RS-232C IN (CONTROL&SERVICE) (CONTROL&SERVICE) OPTICAL OPTICAL AV IN AUDIO IN DIGITAL AUDIO IN DIGITAL AV IN RGB/DVI AUDIO OUTRGB/DVI L(MONO) VIDEOAUDIO OUT AUDIO VIDEOR L(MONO) AUDIO R Connect the RF antenna out socket RGB IN (PC) RGB IN (PC) of the VCR to the ANTENNA/ CABLE Y P VIDEO IN socket on the TV. B M. P.
OTHER A/V SOURCE SETUP 1. How to connect 1 2. How to use ꔛ ꔛ RJP RS-232C IN (SERVICE ONLY) RESET UPDATE REMOTE CONTROL OUT 2 /DVI IN 1 RGB IN (PC) SPEAKER OUT (8 ) AV IN 1 L/MONO AUDIO R VIDEO AUDIO IN (RGB/DVI) Y GAME CONTROL PB VIDEO PR L AUDIO TV - LINK CFG R COMPONENT IN Select the AV1 or AV2 input source on the TV using the INPUT button on the remote control. Operate the corresponding external equipment.
EXTERNAL EQUIPMENT SETUP USB CONNECTION 1. How to connect EXTERNAL EQUIPMENT SETUP 30 Connect the USB device to the USB IN jack on the side of TV. 2. How to use ꔛ After connecting the USB IN jack, you use the USB function.
PC SETUP VGA (D-Sub 15 Pin) Connection RS-232C IN RJP 1. How to connect RESET (SERVICE ONLY) UPDATE REMOTE CONTROL OUT 2 Connect the VGA output of the PC to the RGB IN (PC) jack on the TV. /DVI IN AV IN VIDEO L(MONO) AUDIO R AUDIO IN (RGB/DVI) RGB IN (PC) SPEAKER OUT (8 ) Y GAME CONTROL PB PR VIDEO L AUDIO R COMPONENT IN 2 Connect PC audio output to the AUDIO IN (RGB/DVI) jack on the TV. 2. How to use ꔛ ꔛ 1 2 RGB OUTPUT AUDIO Turn on the PC and the TV.
UPDATE SPEAKER OUT (8 ) Y RS-232C IN PR L AUDIO R COMPONENT IN (SERVICE ONLY) RJP PB VIDEO EXTERNAL EQUIPMENT SETUP REMOTE CONTROL OUT AUDIO IN (RGB/DVI) AV IN 1 VIDEO L/MONO AUDIO R GAME CONTROL RGB IN (PC) SPEAKER OUT(8 ) Y PB VIDEO PR L AUDIO TV - LINK CFG HDMI OUTPUT R COMPONENT IN DVI to HDMI Connection 1. How to connect EXTERNAL EQUIPMENT SETUP 32 1 2 Connect the DVI output of the PC to the HDMI/DVI IN 1 jack on the TV.
! ? ! NOTE ►To get the the best picture quality, adjust the PC graphics card to 1920 x 1080 (Other models), 1360 x 768 (26/32LD320H, 32LD325H, 26/32LD340H, 26/32LD345H, 32LD310H, 32LD330H). ►In PC mode, there may be noise associated with the resolution, vertical pattern, contrast or brightness. If noise is present, change the PC output to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the PICTURE menu until the picture is clear.
EXTERNAL EQUIPMENT SETUP Screen Setup for PC mode Selecting Resolution EXTERNAL EQUIPMENT SETUP You can choose the resolution in RGB-PC mode. The Position, Phase, and Size can also be adjusted. You can choose this option only when the PC resolution is set to 1024X768, 1280X768 or 1360X768. PICTURE ꔂ Move ꔉ Enter SCREEN Resolution • Brightness 50 • Sharpness 70 • Color 60 • Tint 0 R G • Color Temp. 0 W C • Advanced Control • Picture Reset Auto Config.
Auto Configure Automatically adjusts picture position and minimizes image instability. After adjustment, if the image is still not correct, try using the manual settings or a different resolution or refresh rate on the PC. ꔂ Move ꔉ Enter • Brightness 50 Resolution • Sharpness 70 Auto Config. • Color 60 • Tint 0 R G • Color Temp. 0 W C • Advanced Control • Picture Reset • Screen (RGB-PC) Position Size ꔂ Move � Prev. Auto Config.
EXTERNAL EQUIPMENT SETUP Adjustment for screen Position, Size, and Phase If the picture is not clear after auto adjustment or if text is shaking, adjust the picture phase manually. This feature operates only in RGB-PC mode. EXTERNAL EQUIPMENT SETUP PICTURE ꔂ Move ꔉ Enter SCREEN ꔂ Move � Prev. Resolution • Brightness 50 • Sharpness 70 • Color 60 • Tint 0 R G • Color Temp. 0 W C • Advanced Control • Picture Reset Auto Config.
Screen Reset (Reset to original initial values) Returns Position, Size, and Phase to the default initial settings. This feature operates only in RGB-PC mode. ꔂ Move ꔉ Enter ꔂ Move � Prev. Resolution • Brightness 50 • Sharpness 70 • Color 60 • Tint 0 R G • Color Temp. 0 W C • Advanced Control • Picture Reset Auto Config.
WATCHING TV / CHANNEL CONTROL REMOTE CONTROL FUNCTIONS When using the remote control, aim it at the remote control sensor on the TV. The remote control may differ from the images below. POWER ALARM WATCHING TV / CHANNEL CONTROL TIMER INPUT TV Set the time that the TV will automatically turn itself on.. Select the amount of time before your TV turns off automatically. Rotates through inputs. Also switches the TV on from standby. Returns to the last TV channel.
INFO PORTAL MUTE Adjusts the volume. Displays channel information at the bottom of the screen. Displays and removes the hotel interactive menu. Switches the sound on or off. CHANNEL UP/DOWN Changes the channel. PAGE UP/DOWN Moves from one full set of screen information to the next one. COLOR BUTTON VCR/DVD control buttons Access special functions in some menus. WATCHING TV / CHANNEL CONTROL VOLUME UP/DOWN Control video cassette recorders or DVD players. EJECT Eject the USB device.
WATCHING TV / CHANNEL CONTROL TURNING ON THE TV 1 WATCHING TV / CHANNEL CONTROL ! First, connect power cord correctly. At this moment, the TV switches to standby mode. ꔛ In standby mode to turn TV on, press the / I button on the TV or press the button on the remote control. 2 Select the viewing source by using the INPUT button on the remote control. 3 When finished using the TV, press the reverts to standby mode. (POWER) button on the remote control.
ON-SCREEN MENUS SELECTION Your TV's OSD (On Screen Display) may differ slightly from that shown in this manual. 1 2 3 MENU Display each menu. ENTER Select a menu item.
WATCHING TV / CHANNEL CONTROL i.
CUSTOMER SUPPORT Picture Test / Sound Test This function is a customer support function that can execute picture and sound tests. ꔑ Picture Test □ Sound Test ? Do you have a problem in this test screen? □ Product/Service Info. No □ Picture Test ꔑ Sound Test ? Do you have a sound problem in this screen? □ Product/Service Info. Close 1 MENU 2 3 4 RETURN EXIT RED Select Customer Support. ENTER Select Picture Test or Sound Test. ENTER Select Yes.
WATCHING TV / CHANNEL CONTROL Product/Service Info. This function shows support and product information. Customer Service Center can differ by country. □ Picture Test □ Sound Test WATCHING TV / CHANNEL CONTROL ꔑ Product/Service Info. Close 1 MENU 2 3 RETURN EXIT 44 RED Select Customer Support. ENTER Select Product/Service Info.. You can check the various product/Service infomation based on your model. Return to the previous menu. Return to TV viewing.
CHANNEL SETUP Auto Scan (Auto Tuning) Automatically finds all channels available through antenna or cable inputs, and stores them in memory on the channel list. Run this function if you change your residence or move the TV. Auto Tuning memorizes only the channels available at the time. ꔂ Move ꔉ Enter • Auto Tuning • Manual Tuning ꔉ ꔡ CHANNEL ꔂ Move ꔉ Enter • Auto Tuning • Manual Tuning • Channel Edit • Channel Edit • Channel Label • Channel Label Antenna Cable Check your antenna connection.
WATCHING TV / CHANNEL CONTROL Add/Delete Channel (Manual Tuning) When selecting DTV or Cable DTV input signal in Manual Tuning, you can view the on-screen signal strength monitor to see the quality of the signal being received. CHANNEL ꔉ Enter WATCHING TV / CHANNEL CONTROL • Auto Tuning • Manual Tuning • Channel Edit CHANNEL ꔂ Move • Auto Tuning ꔉ ꔀ • Channel Label • Manual Tuning • Channel Edit • Channel Label ꔉ Enter ◀ ▶ DIGITAL Select channel type and RF-channel number.
Channel Editing The channels in the Channel Edit List are displayed in black and the channels deleted from the Channel Edit List are displayed in blue. When a channel number is deleted, it means that you will be unable to select it using CH∧∨button during TV viewing. If you wish to select the deleted channel, directly enter the channel number with the NUMBER buttons or select it in the Channel Edit menu.
WATCHING TV / CHANNEL CONTROL INPUT LIST Only these input signals which are connected to a TV can be activated and selected. ie) Input List WATCHING TV / CHANNEL CONTROL TV AV 1 HDMI2 USB AV 2 Component RGB-PC ꔉ Enter HDMI1 ꕉ Exit 1 ꔛ ꔛ ꔛ ꔛ ꔛ 48 ꔂ Move INPUT ENTER Select the desired input source. TV: Select it to watch over-the-air, cable and digital cable broadcasts. AV: Select them to watch a VCR or other external equipment. Component: Select them to watch DVD or a Digital set-top box.
EXAMPLE ELECTRONIC PROGRAM GUIDE This is an example of a typical TV electronic program guide showing available programming. CHANNEL INDICATOR Currently tuned channel and program. PROGRAMMING GRID Program listings arranged in time slots. DATE/TIME OSD Shows current Date/Time. TV PROGRAM Current program on selected channel. K&M Kids Movies Channel 01:30 AM Mon.
WATCHING TV / CHANNEL CONTROL CHANNEL LABEL Choose preset labels for your channels. If a channel label is provided on the signal from the broadcasting station, the TV displays a short name for a channel even if you didn’t preset a label for the channel.
DEMO MODE Displays a slide show to explain the various feature of this TV. OPTION • Demo Mode ꔂ Move : ꔉ Enter OPTION ꔉ ꔡ • Language • Caption 3 • Eject MENU Select OPTION. ENTER Select Demo Mode. ENTER Select On to show the various feature of the TV. 4 EXIT • Caption : Off ꔉ Enter □ Off ꔑ On WATCHING TV / CHANNEL CONTROL 2 ꔂ Move : Off • Language : Off • Eject 1 • Demo Mode Return to TV viewing. After a while, Demo Mode. starts.
MY MY MEDIA MEDIA CONNECTION METHOD USB Connection USB IN 1 Connect the USB device to the USB IN jack on the side of TV.
Precautions when using the USB device MY MEDIA ►Only a USB storage device is recognizable. ►Connecting a USB storage device through a USB hub is not supported. ►A USB storage device which uses its own driver may not be recognized. ►The recognition speed of a USB storage device may depend on each device. ► Please do not turn off the TV or unplug the USB device when the connected USB storage device is working.
MY MEDIA ENTRY MODE The My Media menu will open automatically when you insert a USB drive. My Media can also be accessed by choosing My Media in the user menu. On USB device, you can not add a new folder or delete the existing folder. For LD340H, LD345H, LD330H series For LD320H, LD325H, LD310H series MY MEDIA MY MEDIA Fl Photo List MY MEDIA 1 2 3 54 Music List Extra Contents MENU Select MY MEDIA. ENTER Select Photo List, Music List, or Extra Contents.
PHOTO LIST The On-Screen Display on your model may be slightly different. Supported photo file: *.JPG ꔛ Baseline: 64 pixel (width) x 64 pixel (height) to 15360 pixel (width) x 8640 pixel (height) ꔛ Progressive: 64 pixel (width) x 64 pixel (height) to 1920 pixel (width) x 1440 pixel (height) ꔛ You can play JPEG files only. ꔛ Non-supported files are displayed in the form of predefined icon. Screen Components 1 2 3 4 5 2 Select MY MEDIA. MENU Moves to upper level folder. Current page/total pages.
MY MEDIA Photo Selection 1 Page 1/1 Photo List USB 1 XTICK Drive1 Page 1/1 � Move MY MEDIA 1 To Music List 1 2 3 Change Numbers1 2 3 4 5 6 4 5 6 7 8 9 7 8 9 0 Mark Mode 1 2 7 8 2 ENTER 3 ENTER 3 �4 View 5 6 � Page Change 0 Select the target folder or drive. ꔛ 9 Exit Select the desired photos. Photo file is displayed. Use the CH (ꕌꕍ) button to navigate in the photo page.
Full Screen Menu More operations are available in full screen mode. Page 1/1 Photo List USB 1 XTICK Drive1 Page 1/1 � Move 1 Numbers 1 2 Change 3 2 3 Mark Mode 4 5 6 4 5 6 7 8 9 7 8 9 0 2 7 8 0 3 6� Page Change 9 MY MEDIA 1 To Music List 1 � View 4 5 Exit 0 01_a.jpg 2008/12/10 1920 x 1080 479 KB ◀ ▶ ◀ Slideshow � 1 BGM � � � 2/13 ▶ Option Hide 1 2 3 4 5 6 7 8 Select the target folder or drive.
4 01_a.jpg 2008/12/10 1920 x 1080 479 KB ENTER Select the Slideshow, ◀ BGM, � (Rotate), ▶ � (Zoom In), Option, or Hide. ꔛ ◀ MY MEDIA ▶ MY MEDIA Slideshow � BGM � � � 2/13 Option 1 ▶ Hide 2 4 5 7 8 0 3 6 Use < > button to select the previous or next photo. 9 Exit ► Slideshow: Selected photos are displayed during the slide show. If no photo is selected, all photos in the current folder are displayed during slide show.
Using the Photo List Function 01_a.jpg 2008/12/10 1920 x 1080 479 KB Choose options. Set Photo View. ◀ ▶ Set Video. Set Audio. Close Slideshow � 1 BGM � � 2/13 � 1 ▶ Option Hide 2 3 4 5 6 7 8 9 ENTER Show the Option menu. 2 ENTER Select Set Photo View, Set Video, or Set Audio. 0 MY MEDIA ◀ Exit ! ? ! NOTE ► Option values changed in Photo List do not affect Music List. ? Set Photo View Menu Options Set Photo View.
MY MEDIA ꔛ Image shown may differ from your TV. Set Video Menu Options Set Video. ◀ Picture Mode 1 MY MEDIA 2 ▶ • Backlight 70 ◀ ▶ • Contrast 100 ◀ ▶ • Brightness 50 ◀ ▶ • Color 60 ◀ ▶ • Dynamic Contrast ◀ Medium ▶ • Edge Enhancer ◀ High ▶ • Noise Reduction ◀ Medium ▶ 2 4 5 7 8 0 1 Standard 3 6 9 Picture Reset � Previous Select Picture Mode. Make appropriate adjustments. Set Audio Menu Options Set Audio.
MUSIC LIST This TV cannot play back copy-protected files. The On-Screen Display on your model may be slightly different. MUSIC (*.MP3) supporting file Bit rate 32 Kbps - 320 Kbps • Sampling rate MPEG1 Layer3: 32 kHz, 44.1 kHz, 48 kHz • Sampling rate MPEG2 Layer3: 16 kHz, 22.05 kHz, 24 kHz • Sampling rate MPEG2.5 Layer3: 8 kHz, 11.025 kHz, 12 kHz 1 Select MY MEDIA. MENU 2 ENTER Select Music List.
MY MEDIA Music Selection Page 1/1 Music List Drive1 USB 1 XTICK 001. - B01.mp3 00:00 Page 1/1 002. - B02.mp3 00:00 003. - B03.mp3 00:00 004. - B04.mp3 00:00 005. - B05.mp3 00:00 � Move 1 To Photo List Numbers1 2 Change 3 4 5 6 2 3 4 5 6 7 8 7 8 9 1 9 1 2 7 8 1 2 ENTER 3 ENTER Select the desired music file. Music files are played. 3 � Play � Page Change 4 5 6 Mark Mode 0 9 Exit ꔛ 0 MY MEDIA 0 Select the target folder or drive.
Using the Music List Function Page 1/1 Music List 3 file(s) Marked Drive1 Choose options. Page 1/1 Set Audio Play. � 001. - B01.mp3 00:00 002. - B02.mp3 00:00 002. - B02.mp3 � � � 004. - B04 .mp3 00:00 �� � � 003. - B03.mp3 00:00 � Play with Photo � 005. - B05 .mp3 00:00 02:30 / 03:25 Option Hide ENTER Show the Option menu. 2 ENTER Select Set Audio Play or Set Audio. Close 1 2 3 4 5 6 7 8 0 9 Exit ! ? ! NOTE MY MEDIA 1 � Set Audio.
MY MEDIA Set Audio Play Menu Options Set Audio Play. Repeat ◀ On ▶ Random ◀ Off ▶ � Previous MY MEDIA 1 2 Select Repeat or Random. Make appropriate adjustments. Set Audio Menu Options Set Audio. Sound Mode ◀ Standard ▶ Auto Volume ◀ Off ▶ Clear Voice II ◀ Off ▶ Balance 0 ◀ L R ▶ � Previous 1 2 64 Select Sound Mode, Auto Volume, Clear Voice II, or Balance. Make appropriate adjustments.
If you don't press any buttons for a while, the play information box will float across the screen. This prevents screen pixel damage due to a fixed image remaining on the screen for a extended period of time. ꔛ 002. B02.mp3 � 00:31 / 04:04 ? ! NOTE MY MEDIA ! ► Music files with copy-protection will not play. ► Press ENTER or � button to stop the screen saver. ? EXTRA CONTENTS Extra Contents will be activated when Data Channel service is available. You can play application files from USB device.
PICTURE PICTURECONTROL CONTROL PICTURE SIZE (ASPECT RATIO) CONTROL This feature lets you choose the way an analog picture with a 4:3 aspect ratio is displayed on your TV. You can select a different aspect ratio depending on input source (analog broadcasting, digital broadcasting, aux).
4:3 Adjust the picture horizontally, in a linear proportion to fill the entire screen. Choose 4:3 when you want to view a picture with an original 4:3 aspect ratio. Just Scan Zoom Normally the edges of video signals are cropped 1-2%. Just Scan turns off this cropping and shows the complete video. Notes: If there is noise on the edges of the original signal, it will be visible when Just Scan is activated.
PICTURE CONTROL PRESET PICTURE SETTINGS (PICTURE MODE) There are factory presets for picture settings available in the user menus. You can use a preset, change each setting manually.
MANUAL PICTURE ADJUSTMENT - USER MODE Adjust the picture appearance to suit your preference and viewing situations. PICTURE 2 3 4 5 • Aspect Ratio : 16:9 • Picture Mode : Standard • Backlight 70 • Contrast 100 • Brightness 50 • Sharpness 70 • Color 50 • Tint 0 ꔉ Enter ꔉ ꔀ R ENTER Select Picture Mode. ENTER Select Vivid, Standard, Cinema, Sport, or Game. ENTER Select Backlight, Contrast, Brightness, Sharpness, Color, Tint, Color Temp.
PICTURE CONTROL PICTURE IMPROVEMENT TECHNOLOGY (ADVANCED CONTROL) Advanced Control allows you to adjust some of the advanced features of your LG display. To reset to the factory default after making adjustments to each input source, execute the Picture Reset function for each Picture Mode. PICTURE ꔂ Move ꔉ Enter ꔂ Move • Brightness • Sharpness • Brightness 70 • Sharpness 70 • Color 60 • Color • Tint 0 R G • Tint • Color Temp.
*This feature is not available for all models. ꔛ Adjusts the contrast to keep it at the best level according to the brightness of the screen. The picture is improved by making bright parts brighter and dark parts darker. ꔛ Adjusts screen colors so that they look livelier, richer and clearer. This feature enhances hue, saturation and luminance so that red, blue and green white look more vivid. Skin Color ꔛ It detects the skin area of video and adjusts it to express a natural skin color.
PICTURE CONTROL ꔛ xvYCC PICTURE CONTROL 72 ꔛ ꔛ This is produces richer colors. This feature represents rich color as much as conventional video signal. This function is enabled in "Picture Mode - Cinema, Expert" when a xvYCC signal is inputted through HDMI.
PICTURE RESET Settings of the selected picture modes return to the default factory settings. PICTURE ꔂ Move • Brightness 70 • Sharpness 70 picture settings ? • All Color 60 will be reset. Continue? • Tint 0 R G • Color Temp. 0 W Yes • Advanced Control • Picture Reset • Screen (RGB-PC) 2 3 4 MENU Select PICTURE. ENTER Select Picture Reset. ENTER Select Yes.
SOUND & LANGUAGE CONTROL AUTO VOLUME Auto Volume makes sure that the volume level remains consistent whether you are watching a commercial or a regular TV program. Because each broadcasting station has its own signal conditions, volume adjustment may be needed every time the channel is changed. This feature allows users to enjoy stable volume levels by making automatic adjustments for each program.
CLEAR VOICE II By differentiating the human sound range from others, it improves the sound quality of voices. AUDIO ꔂ Move • Auto Volume : Off • Clear Voice II : Off � 3 • Balance 1 3 : Standard ꔉ ꔀ 0 L R • Auto Volume : Off • Clear Voice II : Off � 3 • Balance • Infinite Sound: Off • Infinite Sound: Off • Treble 50 • Treble 50 • Bass 50 • Bass 50 • Reset • Reset ENTER Select Clear Voice II. ENTER Select On or Off.
SOUND & LANGUAGE CONTROL BALANCE Adjust the left/right sound of speaker to suit your taste and room situations. AUDIO ꔂ Move SOUND & LANGUAGE CONTROL 76 2 3 : Off • Auto Volume : Off : Off � 3 • Clear Voice II : Off � 3 0 L ꔀ R ꔉ : Standard • Sound Mode : Standard • Infinite Sound: Off • Infinite Sound: Off • Treble 50 • Treble 50 • Bass 50 • Bass 50 • Reset • Reset Select Balance. ENTER Make appropriate adjustments. Return to the previous menu.
PRESET SOUND SETTINGS (SOUND MODE) Sound Mode lets you enjoy the best sound without any special adjustment using factory presets. AUDIO ꔂ Move 3 ꔂ Move : Off • Auto Volume : Off • Clear Voice II : Off � 3 • Clear Voice II : Off � 3 0 L R ꔉ ꔀ • Balance • Sound Mode : Standard • Infinite Sound: Off • Sound Mode : Standard • Treble 50 • Bass 50 • Bass • Reset • Reset • Treble Select AUDIO. ꔛ ENTER Select Sound Mode.
SOUND & LANGUAGE CONTROL SOUND SETTING ADJUSTMENT - USER MODE Adjust the sound to suit your taste and room situations.
AUDIO RESET Settings of the selected Sound Mode return to the default factory settings. AUDIO • Clear Voice II ꔂ Move : Off � 3 • Balance L • Balance R 0 : Standard • Infinite Sound:Off • Treble • Bassi • Reset • TV Speaker : On • Bass Yes 50 • Reset No ꔉ ꔀ : On MENU Select AUDIO. ENTER Select Reset. ENTER Select Yes. 4 ENTER EXIT L R 50 50 audio configuration... Resetting Initialize the adjusted value. Return to TV viewing.
SOUND & LANGUAGE CONTROL AUDIO LANGUAGE This feature operates only in DTV/Cable DTV mode. OPTION • Demo Mode ꔂ Move ꔉ Enter : Off • Language • Caption : Off • Eject SOUND & LANGUAGE CONTROL 1 2 3 MENU Select OPTION. ENTER Select Language. ENTER Select Audio Language. 4 Select your desired language. 5 RETURN EXIT 80 Return to the previous menu. Return to TV viewing.
ON-SCREEN MENUS LANGUAGE SELECTION The menus can be shown on the screen in the selected language. OPTION • Demo Mode ꔂ Move : Off : Off • Eject 2 3 MENU Select OPTION. ENTER Select Language. ENTER Select Menu Language. Select your desired language. From this point on, the on-screen menus will be shown in the selected language.
SOUND & LANGUAGE CONTROL CAPTION MODE Analog Broadcasting System Captions Captions are provided to help the hearing impaired watch TV. Select a caption mode for displaying captioning information if provided on a program. Analog caption displays information at any position on the screen and is usually the program's dialog. Caption/Text, if provided by the broadcaster, would be available for both digital and analog channels on the Antenna/Cable.
Digital Broadcasting System Captions Choose the language you want the DTV/Cable DTV Captions to appear in. Other Languages can be chosen for digital sources only if they are included on the program. This function in only available when Caption Mode is set On. OPTION • Demo Mode ꔂ Move ꔉ Enter : Off • Demo Mode • Language • Caption OPTION ꔂ Move : Off • Language : Off ꔉ ꔀ • Eject • Caption • Eject : Off ◀ ꔉ Enter On Mode ▶ CC1 Digital Option Close 2 3 MENU Select OPTION.
SOUND & LANGUAGE CONTROL Caption Option Customize the DTV/Cable DTV captions that appear on your screen. This function in only available when Caption Mode is set On.
TIME SETTING CLOCK SETTING Auto Clock Setup The time is set automatically from a digital channel signal. The digital channel signal includes information for the current time provided by the broadcasting station. Set the clock manually if the current time is set incorrectly by the auto clock function.
TIME SETTING Manual Clock Setup If the current time setting is wrong, reset the clock manually. TIME ꔂ Move • Clock ꔉ Enter ꔉ • Off Time : Off • On TIme • Sleep Timer • Auto Off ꔡ TIME ꔂ Move • Clock ꔉ Enter ◀ Manual : Off : Off • On TIme : Off : Off • Sleep Timer : Off Date 21 : On • Auto Off : On Year 2010 Hour 10 AM Month 02 Minute 10 Time Zone Eastern Daylight Saving Auto Close TIME SETTING 1 2 3 MENU Select TIME. ENTER Select Clock. ENTER Select Manual.
AUTO ON/OFF TIME SETTING This function operates only if the current time has been set. The Off Time function overrides the On Time function if they are both set to the same time. The TV must be in standby mode for the On Time to work. TIME ꔂ Move ꔉ Enter • Clock TIME ꔂ Move ꔉ Enter • Clock • Off Time : Off • On TIme : Off • Sleep Timer : Off • Sleep Timer • Auto Off : On • Auto Off ꔉ ꔀ ꔎ Feb.
TIME SETTING SLEEP TIMER SETTING The Sleep Timer turns the TV off at the preset time. Note that this setting is cleared when the TV is turned off. TIME ꔂ Move TIME ꔉ Enter • Clock ꔂ Move ꔉ Enter • Clock • Off Time : Off • Off Time : Off • On TIme : Off • On TIme : Off • Sleep Timer : Off • Sleep Timer : Off • Auto Off : On • Auto Off : On ꔉ ꔀ ꔑ Off ꔉ ꔡ □ 10 min. □ 20 min. □ 30 min. □ 60 min. □ 90 min. □ 120 min. □ 180 min. □ 240 min. 1 2 3 4 MENU Select TIME.
PARENTAL CONTROL / RATINGS Parental Control can be used to block specific channels, ratings and other viewing sources. The Parental Control Function (V-Chip) is used to block program viewing based on the ratings sent by the broadcasting station. The default setting is to allow all programs to be viewed. Viewing can be blocked by choosing the type of the program and the categories. It is also possible to block all program viewing for a time period. To use this function, the following must be done : 1.
PARENTAL CONTROL / RATINGS Set Password Change the password by inputting a new password twice. LOCK ꔂ Move ꔉ Enter • Set Password 1 2 1 2 3 4 5 6 7 8 9 : On ꔡ PARENTAL CONTROL / RATING 90 4 • Block Channel Confirm • Movie Rating • Movie Rating • TV Rating-Children • TV Rating-Children • TV Rating-General • TV Rating-General • Downloadable Rating • Downloadable Rating • Input Block • Input Block Select LOCK. Input the password.
Lock System Enables or disables the blocking scheme you set up previously.
PARENTAL CONTROL / RATINGS CHANNEL BLOCKING Blocks any channels that you do not want to watch or that you do not want your children to watch. Block Channel LOCK ꔂ Move DIGITAL ꔉ Enter • Set Password • Lock System : On • Block Channel • Movie Rating • TV Rating-Children • TV Rating-General • Downloadable Rating • Input Block page 1/1 ꔉ ꔀ ꔉ CH.
MOVIE & TV RATING Movie Rating (MPAA) Blocks movies according to the movie ratings limits specified, so children cannot view certain movies. You can set the ratings limit by blocking out all the movies with the ratings above a specified level. Keep in mind that the movie ratings limit only applies to movies shown on TV, not TV programs, such as soap operas.
PARENTAL CONTROL / RATINGS TV Rating Children revents children from watching certain children's TV programs, according to the ratings limit set. The P children rating does not apply to other TV programs. Unless you block certain TV programs intended for mature audiences in the TV Rating - sub menu, your children can view those programs.
TV Rating General Based on the ratings, blocks certain TV programs that you and your family do not want to view.
PARENTAL CONTROL / RATINGS DOWNLOADABLE RATING This function is available only for digital channels. This function operates only when TV has received Region5 Rating data.
EXTERNAL INPUT BLOCKING Enables you to block an input.
APPENDIX APPENDIX TROUBLESHOOTING Abnormal Operation ꔛ The remote control doesn’t work ꔛ ꔛ ꔛ TV turns off suddenly ꔛ ꔛ Check to see if there is any object between the product and the remote control causing obstruction. Ensure you are pointing the remote control directly at the TV. Ensure that the batteries are installed with correct polarity (+ to +, - to -). Ensure that the correct remote operating mode is set: TV, VCR etc. *This feature is not available for all models. Install new batteries.
Audio Problems No output from one of the speakers Unusual sound from inside the product No sound when connecting HDMI/USB ꔛ Adjust Balance in menu option. ꔛ A change in ambient humidity or temperature may result in an unusual noise when the product is turned on or off and does not indicate a fault with the product. ꔛ Check High Speed HDMI cable. Check USB cable over version 2.0. Use normal MP3 file. *This feature is not available for all models.
APPENDIX MAINTENANCE Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you can enjoy your new TV. Caution: Be sure to turn the power off and unplug the power cord before you begin any cleaning. Cleaning the Screen 1 ere’s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of H lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and then use it to wipe the screen.
PRODUCT SPECIFICATIONS 32LD320H (32LD320H-UA), 32LD325H (32LD325H-UA), 32LD340H (32LD340H-UA), 32LD345H (32LD345H-UA) With stand 667.0 mm x 502.7 mm x 206.8 mm (26.2 inch x 19.7 inch x 8.1 inch) 805.0 mm x 585.0 mm x 206.8 mm (31.6 inch x 23.0 inch x 8.1 inch) Without stand 667.0 mm x 446.2 mm x 80.0 mm (26.2 inch x 17.5 inch x 3.1 inch) 805.0 mm x 528.2 mm x 108.9 mm (31.6 inch x 20.7 inch x 4.2 inch) With stand 9.4 kg (20.7 lbs) 13.1 kg (28.8 lbs) Without stand 7.7 kg (16.9 lbs) 11.
APPENDIX IR CODE Code (Hexa) Function Note 00 CH ꕌ Remote Control Button B0 01 CH ꕍ Remote Control Button B1 02 VOL + Remote Control Button BA ꕖ ꕗ ꕘ 03 VOL - Remote Control Button D6 TV 06 > Remote Control Button 07 < Remote Control Button C4 POWER ON (Power On/Off) 09 MUTE Remote Control Button 0B INPUT Remote Control Button 0F TV Remote Control Button 10-19 Number 0-9 Remote Control Button 1A FLASHBK Remote Control Button AA INFO Remote Control Button 28 RET
OPEN SOURCE LICENSE GNU GENERAL PUBLIC LICENSE Version 2, June 1991 Copyright (C) 1989, 1991 Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. Preamble The licenses for most software are designed to take away your freedom to share and change it.
APPENDIX b) Y ou must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part there of, to be licensed as a whole at no charge to all third parties under the terms of this license.
7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this license, they do not excuse you from the conditions of this license.
APPENDIX END OF TERMS AND CONDITIONS How to apply these terms to your new programs If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to make it free software which everyone can redistribute and change under these terms. To do so, attach the following notices to the program.
GNU LESSER GENERAL PUBLIC LICENSE Version 2.1, February 1999 Copyright (C) 1991, 1999 Free Software Foundation, Inc. 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. [This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library Public License, version 2, hence the version number 2.1.
APPENDIX Although the Lesser General Public License is Less protective of the users' freedom, it does ensure that the user of a program that is linked with the Library has the freedom and the wherewithal to run that program using a modified version of the Library. The precise terms and conditions for copying, distribution and modification follow. Pay close attention to the difference between a "work based on the library" and a "work that uses the library".
3. You may opt to apply the terms of the ordinary GNU General Public License instead of this License to a given copy of the Library. To do this, you must alter all the notices that refer to this License, so that they refer to the ordinary GNU General Public License, version 2, instead of to this License. (If a newer version than version 2 of the ordinary GNU General Public License has appeared, then you can specify that version instead if you wish.) Do not make any other change in these notices.
APPENDIX For an executable, the required form of the "work that uses the library" must include any data and utility programs needed for reproducing the executable from it. However, as a special exception, the materials to be distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable.
If the library does not specify a license version number, you may choose any version ever published by the Free Software Foundation. 14. If you wish to incorporate parts of the library into other free programs whose distribution conditions are incompatible with these, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this.
APPENDIX MOZILLA PUBLIC LICENSE Version 1.1 --------------which, at the time of its release under this license is not already covered code governed by this license. 1.Definitions. 1.0.1. “Commercial use” means distribution or otherwise making the covered code available to a third party. 1.1. “Contributor” means each entity that creates or contributes to the creation of modifications. 1.2.
(c) t he licenses granted in this section 2.1(a) and (b) are effective on the date Initial developer first distributes original code under the terms of this license. (d) Notwithstanding section 2.1(b) above, no patent license is granted: 1) for code that You delete from the original Code; 2) separate from the original code; or 3) for infringements caused by: i) the modification of the original code or ii) the combination of the original code with other software or devices. 2.2. Contributor Grant.
APPENDIX (c) Representations. contributor represents that, except as disclosed pursuant to section 3.4(a) above, contributor believes that contributor's modifications are contributor's original creation(s) and/or contributor has sufficient rights to grant the rights conveyed by this license. 3.5. Required notices. You must duplicate the notice in exhibit A in each file of the source code.
7. DISCLAIMER OF WARRANTY. COVERED CODE IS PROVIDED UNDER THIS LICENSE ON AN “AS IS” BASIS, WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, WARRANTIES THAT THE COVERED CODE IS FREE OF DEFECTS, MERCHANTABLE, FIT FOR A PARTICULAR PURPOSE OR NON-INFRINGING. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE COVERED CODE IS WITH YOU.
APPENDIX 11. MISCELLANEOUS. This license represents the complete agreement concerning subject matter hereof. If any provision of this license is held to be unenforceable, such provision shall be reformed only to the extent necessary to make it enforceable. This License shall be governed by California law provisions (except to the extent applicable law, if any, provides otherwise), excluding its conflict-of-law provisions.
OWNER’S MANUAL LCD TV Please read this manual carefully before operating your set and retain it for future reference. 26LD320H 32LD320H 37LD320H 42LD320H 32LD325H 37LD325H 26LD340H 32LD340H 37LD340H 42LD340H 26LD345H 32LD345H 37LD345H 42LD345H 32LD310H 37LD310H 32LD330H 37LD330H The model and serial number of the TV is located on the back and one side of the TV. Record it below should you ever need service. MODEL SERIAL P/NO : SAC34026009 (1104-REV03) www.lg.
26LD320H 32LD320H 37LD320H 42LD320H 32LD325H 37LD325H Lodging Guest Interactive Pro:Centric™ TVs Commercial Mode Setup Guide Note: Selected features shown in this guide may not be available on all models. EXPERIENCED INSTALLER Commercial Mode Setup pages 12 – 13 Cloning Information pages 27 – 32 b-LAN™ Setup & Overview page 39 © Copyright 2011, LG Electronics U.S.A., Inc.
For Customer Support/Service, please call: 1-888-865-3026 The latest product information and documentation is available online at: www.LGsolutions.com/products MODEL and SERIAL NUMBER The model and serial numbers of this TV are located on the back of the cabinet. For future reference, LG suggests that you record those numbers here: Model No._________________Serial No.
IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources, such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
IMPORTANT SAFETY INSTRUCTIONS (Continued from previous page) 22. Outdoor Antenna Grounding If an outside antenna or cable system is connected to the product, follow the precautions below. An outdoor antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits or where it can come into contact with such power lines or circuits as death or serious injury can occur.
Table of Contents Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Important Safety Instructions . . . . . . . . . . . . . . . . . . . 3 – 4 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Setup Checklist / Overview . . . . . . . . . . . . . . . . . . . . . . 6 Pro:Centric TV Interactive Menu Features. . . . . . . . . . . 7 Learning / Teaching a Master TV Setup using a TLL-1100A Clone Programmer . . . . . . . . . . . .
Setup Checklist / Overview Setup Checklist Installation and Setup Checklist __ Unpack TV and all accessories. __ Install batteries in remote control. __ Install TV on VESA mount or stand. Note: It may be advisable to make all cable connections before installing on VESA mount or stand, as appropriate. Hardware Connections __ Install any additional hardware as appropriate to your institution, LAN, etc.
Pro:Centric TV Interactive Menu Features Channel Guide Information Remote Help Watch TV Important: Pro:Centric operation requires that Installer Menu items 098 PRO:CENTRIC and 119 DATA CHANNEL be set appropriately and that the TV be in PPV or FTG Mode. The interactive Pro:Centric TV enables guests—from the comfort of their hotel rooms—to view and select from a complete listing of hotel services and amenities.
LD320H/LD325H Rear Jack Panel AUDIO IN (RGB/DVI) Audio connection for RGB or DVI device. RJP Connection for Remote Jack Pack (RJP) Control cable. REMOTE CONTROL OUT IR output for controlling an auxiliary device. UPDATE Restricted to software updates. RESET Press RESET to re-initialize the TV. AUDIO/VIDEO IN 1 Connection for composite audio/ video output from external device. RS-232C IN (SERVICE ONLY) RESET HDMI HDMI /DVI IN 2 1 UPDATE ..... .... RJP REMOTE CONTROL OUT .......... .......... ..
Side Connections Panel / RF Antenna & MPI Connections A/V 2 Input L/MONO-AUDIO-R IN Connect to audio output jacks on external device. For only mono audio output, connect to Left audio input. VIDEO L/MONO -AUDIO- R USB IN Insert USB memory device for software updates, cloning purposes, or picture/music entertainment, as applicable. USB IN Side Connections Panel VIDEO IN Connect to video output port on external device (see Reference section, “TV Camport Auto Sense Operation,” for further information).
Installer Overview This is the Commercial Mode Setup Guide only. Installer Menu / Commercial Mode Setup XXLD320H PTC INSTALLER MENU To set up a Master TV, you will need to know how to enter the TV Installer Menu and make changes to the default values as required. Similarly, to configure a single TV’s Installer Menu settings in FTG Mode, you will need to know how to access and use the FTG Configuration Application utilities.
Installer Remote Control Typical Key Functions The LG Installer Remote illustrated below and throughout this document shows typical remote control functions and is provided for reference only. This Installer Remote may vary from the Installer Remote supplied with the TV. POWER Turns TV On or Off. ALARM Sets the time when the TV will automatically turn itself ON. TIMER Sets the amount of time before the TV automatically turns itself OFF.
Commercial Mode Setup for Master TV This section describes how to set up a Master TV when the EBL is in Pass-through Mode. Note: Disconnect all Aux inputs. Under certain conditions, Auto Tuning (Channel Search) is disabled if there is an Aux input active. Note: Refer to “FTG Mode of Operation” on pages 23 to 26 for information on con guring/editing Channel Map and Installer Menu settings for an individual TV in FTG Mode. 1. Set Installer Menu items.
Commercial Mode Setup for Master TV (Cont.) (Continued from previous page) 3. Run Auto Tuning (Channel Search). a) Search for all available analog and digital channels: Go to the Channel Menu, select the Auto Tuning option, and follow the on-screen instructions. b) Use the Channel Edit option in the Channel Menu to edit the channel lineup, as necessary, to include free to guest channels only. • Add/delete channels per your system requirements.
Installer Menu Use the Installer Menu to set up or change operational settings. Refer to the table starting on the next page for brief descriptions of Installer Menu items. More detailed descriptions follow the table listing. Accessing the Installer Menu Make sure the TV is ON. Using an Installer Remote, press MENU repeatedly until the on-screen setup menus lock up, and then press 9-8-7-6 + ENTER to access the Installer Menu. The Installer Menu opens with item 000 INSTALLER SEQ 000.
Installer Menu (Cont.) Installer Menu Items 000 through 071 Menu Item Function Value Range Default Value Brief Description of Function and Comments 000 INSTALLER SEQ 0~3 0 Leave default set to 0. 001 POWER MANAGE 0~7 0 Sets number of hours of no activity before automatic shutoff. 002 AC ON 0/1 0 Set to 1 to enable Auto Turn ON when AC power is applied. 003 BAND/AFC 0~3 1 Selects Tuning Band: 0=Broadcast, 1=CATV, 2=HRC, 3=IRC 0 ~ 127, 255 255 Channel tuned when TV is turned ON.
Installer Menu (Cont.) Installer Menu Items 073 through 119 Menu Item 16 Function Value Range Default Value Brief Description of Function and Comments 073 CH NOT AVBLE 0/1 0 If set to 1 and Channel Override is 0, “NOT AVAILABLE” message is displayed when directly accessing a channel not in the favorite Channel List. 075 REVERT CH 0/1 0 If set to 1 and loss of MPI communication occurs, TV tunes to Start Channel. 078 UPN MSB 0 ~ 255 0 User programmable number, most significant byte.
Installer Menu (Cont.) Detailed Descriptions of Installer Menu Items 000 - INSTALLER SEQUENCE Speci es entry sequence to the Installer Menu. 0 = 9876 2 = 1478 To translate a TV volume level to the Installer Menu value, use the following formula: 1 = 4321 3 = 3698 001 - POWER MANAGE (Power Management) Determines hours of no activity before automatic shutoff. The Power Management function is for saving energy. If set to 0, Power Manage is Off.
Installer Menu (Cont.) 015 - SLEEP TIMER If set to 1, the Sleep Timer feature may be used. If set to 0, the Sleep Timer is not available. 016 - EN TIMER (Enable On/Off Timers) * If set to 1, the Timer function is available to the end user and enabled continuously. Set to 0 to disable On/Off timers. Note: Clock must be set in order to use timers. 017 - ALARM * Gives the installer the option of making the Alarm function available to the end user. If set to 1, the Alarm function is available to the end user.
Installer Menu (Cont.) 047 - AUX STATUS Set to 1 for MPI Aux source to be reported as a channel number instead of channel 0. Set to 0 to disable Aux identi cation change. Controls MPI status channel response for Aux inputs. 082 - CHKSM ERROR (Checksum Error) Enforces rigid MPI checksum validation. Set to 1 for validation. Set to 0 to disable (does not check checksum on MPI async port). SPI is always checked. 053 - DIS.
Installer Menu (Cont.) • 6 = Scaler Model RJPs: DVI Mode Enables RJP feature for use with reduced cable bundle models. In this mode, when an HDMI/DVI source is connected to the RJP, only digital video is expected via the HDMI cable. Analog audio is provided via separate cable, from the source, connected to an RJP AUDIO IN. If no analog audio cable is connected, tuner audio will be heard. Notes: See Reference section, “RJP Model List and Input Auto-sensing Hierarchy.
TV Setup Menus Overview On-screen setup menus control the features of the TV. Press MENU on the Installer Remote to access the TV setup menus, and set the TV features to the desired configuration for the end user. CHANNEL PICTURE AUDIO TIME LOCK OPTION INPUT MY MEDIA Refer to the Owner’s Manual for further information on the TV setup menus.
Adding Channel Label Icons / Custom Channel Labels (2-5-4 + MENU Mode) Editing/Adding Channel Icons and/or Labels If there is no pre-assigned icon, you can make a custom channel label of up to seven (7) characters to help identify a channel or network. If desired, channel labels can also be added in addition to a pre-assigned icon. You may also add labels for the Aux input sources to clearly identify the devices that are connected to the Aux inputs.
FTG Mode of Operation FTG Configuration Overview The following steps outline local FTG configuration of individual TVs. Since these models are equipped with the EBL module, they can also be broadcast configured in FTG Mode by a Free-To-Guest Management Appliance (FMA) head end device. Refer to the Free-To-Guest (FTG) Configuration Application manual and/or the Installation & Setup manual for the FMA device for further information. Note: FTG Configuration Application software is available online at: www.
FTG Mode of Operation (Cont.) Determining the TV Operating Mode / FTG Channel Map Configuration Utility Overview To determine the operating mode of the TV, press MENU on the Installer Remote. If the end user Function Menu (showing aspect ratio options—see below) appears, the TV/EBL is in FTG Mode. If the TV setup menus appear, the EBL is in Passthrough Mode.
FTG Mode of Operation (Cont.) FTG Channel Map Configuration Utility / FTG Channel Map Editor Overview The FTG Channel Map Editor shows a single Logical Channel’s Data and the FTG Channel Map. LOGICAL CHANNEL MAPPING Select a Logical Channel number, then assign it the RF, Major, and Minor channel numbers to complete the mapping. CUSTOM CHANNEL LABELS/ICONS Enter custom labels and select icons by name on menu or by number. DELETE Click to remove highlighted channel from FTG Channel Map.
FTG Mode of Operation (Cont.) FTG Installer Menu Configuration Utility Overview CONFIGURATION SETTINGS Select tabs for categories of Installer Menu items to set up TV. INSTALLER DEFAULTS Click to reset FTG Installer Menu items shown in the FTG Configuration Application to defaults. IR REMOTE ACCESS Toggle IR Remote Access to ON to obtain access to TV setup menus and Installer Menu. WRITE Click to transfer the FTG Installer Menu settings to the EBL.
Cloning Overview / Clonable Menu Features IMPORTANT CLONING INFORMATION There are three options for cloning a Master TV Setup: • Using a USB memory device • Using a TLL-1100A clone programmer • Using a LT2002 clone programmer Each option is described in further detail on the pages that follow. As you perform cloning procedures, be sure to complete each task as indicated. If a procedure or step is omitted or not performed completely, cloning may not work.
Cloning Procedures Learning / Teaching a Master TV Setup using a USB Memory Device USB Cloning Notes • Read the IMPORTANT CLONING INFORMATION on page 27 before beginning any cloning procedures. • You may edit a lename as part of the Learning procedure; however, a le with edited contents will not be recognized. • It is not possible to clone a Master TV’s clock using a USB memory device. Either set a Target TV’s clock manually, or use the Auto Clock setting in the TV setup menus.
Cloning Procedures (Cont.) Learning / Teaching a Master TV Setup using a TLL-1100A Clone Programmer Warning: Do not connect a clone programmer to a PPV card installed in the Master or Target TVs. Also, if the TV is in LodgeNet PPV Mode (check with the site administrator if you are not certain), do not connect a clone programmer to the GAME CONTROL/MPI port. Either of these actions will damage the clone programmer and, if applicable, the PPV card.
Cloning Procedures (Cont.) Learning / Teaching a Master TV Setup using a TLL-1100A Clone Programmer (Cont.) (Optional) Set the Clock Set the time on a Master TV’s clock. (If the time has already been copied from a TV into the TLL-1100A clone programmer, you can set the Master TV’s clock by copying the time from the clone programmer.) The TLL1100A can copy the current time to both a Master TV and to the clone’s internal clock—accurate to within one minute.
Cloning Procedures (Cont.) Learning / Teaching a Master TV Setup using an LT2002 Clone Programmer Warning: Do not connect a clone programmer to a PPV card installed in the Master or Target TVs. Also, if the TV is in LodgeNet PPV Mode (check with the site administrator if you are not certain), do not connect a clone programmer to the GAME CONTROL/MPI port. Either of these actions will damage the clone programmer and, if applicable, the PPV card.
Cloning Procedures (Cont.) Learning / Teaching a Master TV Setup using an LT2002 Clone Programmer (Cont.) (Continued from previous page) 6. Once you select the clone Memory Bank, press ENTER on the Installer Remote. The Memory Bank you selected will be shown. 7. Press POWER to transfer the Master TV Setup into the selected Memory Bank on the LT2002. Learning usually takes about 90 seconds. “LEARNING IN PROGRESS” will be displayed on the screen while the LT2002 copies the Master Setup.
Remote Jack Pack / TV Connections & Setup Remote Jack Pack Setup RJP Available? If you will use a Remote Jack Pack (RJP) in your system, set Installer Menu item 093 RJP AVAILABLE appropriately (for example, on a legacy model RJP: HDMI Mode, set RJP AVAILABLE to 001). See Installer Menu detailed descriptions for further information. 093 RJP AVAILABLE 001 TV Connections Make these connections ONLY after Commercial Mode Setup and Cloning Master TV procedures are complete.
Reference: Upgrading TV/PTC Software using a USB Memory Device Checking the Software Versions XXLD320H PTC INSTALLER MENU Note: This function is not accessible while the TV is in FTG or PPV Mode. You can check the software versions of the TV by accessing the Installer Menu with the Installer Remote: Press MENU repeatedly until the on-screen setup menus lock up, and then press 9-8-7-6 + ENTER. When you are finished, press ENTER again to exit the Installer Menu.
Reference: Downloading a Splash Screen using a USB Memory Device Splash Screen Image File Guidelines USB Download Menu • The splash screen image must be a baseline (not progressive) JPEG. Upgrade TV Software • The image should be no larger than 1 MB. • The ideal size for the image is 1366 x 768 pixels or under. • The image le must be stored in a folder named “LG_DTV” in the root directory of USB memory device. • Ensure the USB device has been formatted with FAT format.
Reference: Power Consumption Settings The following tables assume that Installer Menu item 118 POWER SAVINGS is set to 003 (default) and Installer Menu item 099 BACK LIGHTING is set as shown below (default value is 100). 26LD320H Item 099 Back Lighting (Static) 32LD320H / 32LD325H Power Consumption (Watts) Percent Savings Power Consumption (Watts) 100 56.82 0.00% 72.97 0.00% 90 80 70 60 50 40 30 20 10 1 51.98 47.09 42.06 39.71 37.36 36.31 35.12 32.59 30.23 27.95 8.52% 17.13% 25.97% 30.12% 34.
Reference: TV Camport Auto Sense Operation The Camport Auto Sense function is enabled when: 1. Installer Menu item 034 CAMPORT EN is set to 1 AND 2. Installer Menu item 040 AUTO CAMPORT is enabled (1). Selectable: Can be accessed with INPUT key, direct access, etc. Auto Sense: TV switches to this input when connector is inserted. The Camport (Side [AV IN 2] Video) has the highest priority and will override any commands including tuning to the Start Channel.
Reference: TV Aux Input Configuration ENABLE DIRECT ACCESS Tuning TV Installer Menu MPI DATA MPI DATA STATUS TYPE 0x41 SOURCES ENABLED (R/W) DATA STATUS TYPE 0xD2 CURRENT AV SOURCE (R) DATA STATUS TYPE 0x0D AUX SOURCE (R) START AUX SOURCE ASSIGNMENT OLD_ OCV = 0 OLD_ OCV = 1 Source Input Source Mode Number Labeling Value Labeling Value Labeling 130 90 Video2 (Side) CV 34 CAMPORT_EN 0x01 Video Front (Camport) 0 Video Front (Camport) 0 (VIDEO) 2 131 91 Video1 (Rear) CV 39 RE
Reference: b-LAN Setup & Overview The b-LAN module is internal to the TV. It allows the hotel/institution head end equipment to communicate, via the institution’s RF distribution system, with the TV for configuration and control. Note: MPI cards with b-LAN technology—LMT7Z5, LMT7Z7, LMT7Z9—are NOT supported on TVs in which the b-LAN module is embedded. Power to the b-LAN module is controlled by Installer Menu item 118 POWER SAVINGS.
Reference: RJP Model List and Input Auto-sensing Hierarchy RJP Model List Legacy Models Scaler Models RJP-101M N/A RJP-101ML N/A RJP-110F RJP-210F RJP-110FW RJP-210FW RJP-110W RJP-210W RJP-110WBR RJP-210WBR RJP-110S RJP-210S RJP-120G RJP-220G RJP-120T RJP-220T RJP-201B RJP-301B RJP-202B RJP-302B RJP Input Auto-sensing Hierarchy 40 Priority Video Audio 1st (Highest) Digital Video In Audio In (3.
Troubleshooting General Troubleshooting Some Quick and Easy Tips for Resolving Problems Symptom Possible Cause(s) Possible Solution(s) Channel not included in channel lineup in TV controller. After 2-5-5 + MENU, only channels included in TV controller will appear. If channel is available, it can be added to channel lineup. If it is not available, the “No Signal” message appears on the TV screen. Software Problems Cannot direct enter channel number or “No Signal” appears. Power No power.
Troubleshooting (Cont.) Troubleshooting Flow Chart Controller Quick Check STATUS LED on PTC Board blinking? No TV connected to AC Power? No Plug into AC Power outlet. Yes Yes Bad TV Cycle the power by removing and reconnecting the AC Power cord. Then, observe POWER LED on front of TV. POWER LED lit? No Bad Analog or Digital Board Yes No Bad TV No Bad PPV Card Yes Press POWER on Installer Remote. TV turned ON? TV responded? Press VOLUME UP/ DOWN or MUTE key on User-supplied Remote.
Troubleshooting (Cont.) Commercial Mode Check / FTG Operation Troubleshooting Commercial Mode Check Press POWER on Installer Remote. TV responded? No Bad TV Yes Leave the TV set ON. Go to Installer Menu by pressing MENU until the on-screen setup menus lock up (i.e., stop responding). TV stopped responding or continued to respond? Stopped responding TV is in Commercial Mode. Continued to respond TV is not in Commercial Mode. Call Technical Support for assistance.
Troubleshooting (Cont.) Clone Programmer Troubleshooting Warning: Do not connect a clone programmer to a PPV card installed in the Master or Target TVs. Also, if the TV is in LodgeNet PPV Mode (check with the site administrator if you are not certain), do not connect a clone programmer to the GAME CONTROL/ MPI port. Either of these actions will damage the clone programmer and, if applicable, the PPV card.
Glossary of Terms A list of de nitions for some of the words found in this guide. 75 OHM RF CABLE The wire that comes from an off-air antenna or cable service provider. The end looks like a hex-shaped nut with a wire through the middle. It screws onto the Antenna/Cable threaded jack on the back of the TV. 300 TO 75 OHM ADAPTER A small device that connects a 2-wire 300 ohm antenna to a 75 ohm RF jack.
Document Revision History / Notes Document Revision History Date Description December 2010 Revision A: New Document January 2011 Revision B: Includes LD325H TVs Product documentation is available online at: www.LGsolutions.com/products. From the Products page, select TVs, Systems & Solutions, then LCD TVs, then the applicable TV. Click the Literature & Downloads tab at the bottom of the TV page, and select the required document(s) from the Downloads list.
For Customer Support/Service, please call: 1-888-865-3026 www.LGsolutions.com Pro:Idiom is a registered trademark of Zenith Electronics LLC. Pro:Centric is a trademark of LG Electronics U.S.A., Inc. b-LAN is a trademark of LodgeNet Interactive Corporation. All other trademarks or registered trademarks are the property of their respective owners. © Copyright 2011, LG Electronics U.S.A., Inc.
32LD310H 37LD310H Lodging Guest Interactive Pro:Centric™ TVs Commercial Mode Setup Guide Note: Selected features shown in this guide may not be available on all models. EXPERIENCED INSTALLER Commercial Mode Setup pages 12 – 13 Cloning Information pages 23 – 28 FTG Mode of Operation pages 29 – 36 © Copyright 2011, LG Electronics U.S.A., Inc.
For Customer Support/Service, please call: 1-888-865-3026 The latest product information and documentation is available online at: www.LGsolutions.com/products MODEL and SERIAL NUMBER The model and serial numbers of this TV are located on the back of the cabinet. For future reference, LG suggests that you record those numbers here: Model No._________________Serial No. _______________ WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK).
IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources, such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
IMPORTANT SAFETY INSTRUCTIONS (Continued from previous page) 22. Outdoor Antenna Grounding If an outside antenna or cable system is connected to the product, follow the precautions below. An outdoor antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits or where it can come into contact with such power lines or circuits as death or serious injury can occur.
Table of Contents Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Teaching FMA Configuration to a TV . . . . . . . . . . . . 31 Important Safety Instructions . . . . . . . . . . . . . . . . . . . 3 – 4 Learning an FMA Configuration File from a TV . . . . 31 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Optional Manual Configuration / Setup for a TV. . . . 32 Setup Checklist / Commercial Mode Setup Overview . .
Setup Checklist / Commercial Mode Setup Overview Setup Checklist Installation and Setup Checklist __ Unpack TV and all accessories. __ Install batteries in remote control. __ Install TV on VESA mount or stand. Note: It may be advisable to make all cable connections before installing on VESA mount or stand, as appropriate. Hardware Connections __ Install any additional hardware as appropriate to your institution, LAN, etc.
Pro:Centric TV Interactive Menu Features Channel Guide Information Remote Help Watch TV Important: Pro:Centric operation requires that Installer Menu items 098 PRO:CENTRIC and 119 DATA CHANNEL be set appropriately and that the TV be in PPV or FTG Mode. The interactive Pro:Centric TV enables guests—from the comfort of their hotel rooms—to view and select from a complete listing of hotel services and amenities.
LD310H Rear Jack Panel AUDIO IN (RGB/DVI) Audio connection for RGB or DVI device. UPDATE Restricted to software updates. REMOTE CONTROL OUT IR output for controlling an auxiliary device. RESET Press RESET to re-initialize the TV. RS-232C IN (SERVICE ONLY) RESET UPDATE HDMI 2 .......... HDMI /DVI IN 1 .......... ..... .... REMOTE CONTROL OUT ..... ..... .....
Side Connections Panel / RF Antenna & MPI Connections A/V 2 Input L/MONO-AUDIO-R IN Connect to audio output jacks on external device. For only mono audio output, connect to Left audio input. VIDEO L/MONO -AUDIO- R USB IN Insert USB memory device for software updates, cloning purposes, or picture/music entertainment, as applicable. USB IN Side Connections Panel VIDEO IN Connect to video output port on external device (see Reference section, “TV Camport Auto Sense Operation,” for further information).
Installer Overview This is the Commercial Mode Setup Guide only. Installer Menu / Commercial Mode Setup xxLD310H PTC INSTALLER MENU To set up a Master TV for cloning purposes, you will need to know how to enter the TV Installer Menu and make changes to the default values as required. Similarly, to configure a TV’s Installer Menu settings in FTG Mode, you will need to know how to access and use the FTG Configuration Application utilities.
Installer Remote Control Typical Key Functions The LG Installer Remote illustrated below and throughout this document shows typical remote control functions and is provided for reference only. This Installer Remote may vary from the Installer Remote supplied with the TV. POWER Turns TV ON or OFF. ALARM Sets the time when the TV will automatically turn itself ON. TIMER Sets the amount of time before the TV automatically turns itself OFF.
Commercial Mode Setup for Master TV This section describes how to set up a Master TV for cloning purposes when the TV is in Pass-through Mode. Note: Disconnect all Aux inputs. Under certain conditions, Auto Tuning (Channel Search) is disabled if there is an Aux input active. Note: Refer to “FTG Mode of Operation” on pages 29 to 36 for information on entering FTG Mode and configuring/editing FTG Channel Map and Installer Menu settings using the FTG Configuration Application. 1. Set Installer Menu items.
Commercial Mode Setup for Master TV (Cont.) (Continued from previous page) 3. Run Auto Tuning (Channel Search). a) Search for all available analog and digital channels: Go to the Channel Menu, select the Auto Tuning option, and follow the on-screen instructions. b) Use the Channel Edit option in the Channel Menu to edit the channel lineup, as necessary, to include free to guest channels only. • Add/delete channels per your system requirements.
Installer Menu Use the Installer Menu to set up or change operational settings. Refer to the table starting on the next page for brief descriptions of Installer Menu items. More detailed descriptions follow the table listing. Accessing the Installer Menu 1. Make sure the TV is ON. 2. Using an Installer Remote, press MENU repeatedly until the on-screen setup menus lock up, and then press 9-8-7-6 + ENTER to access the Installer Menu. The Installer Menu opens with item 000 INSTALLER SEQ 000.
Installer Menu (Cont.) Installer Menu Items 000 through 071 Menu Item Function Value Range Default Value Brief Description of Function and Comments 000 INSTALLER SEQ 0~3 0 Leave default set to 0. 001 POWER MANAGE 0~7 0 Sets number of hours of no activity before automatic shutoff. 002 AC ON 0/1 0 Set to 1 to enable Auto Turn ON when AC power is applied. 003 BAND/AFC 0~3 1 Selects Tuning Band: 0=Broadcast, 1=CATV, 2=HRC, 3=IRC 0 ~ 127, 255 255 Channel tuned when TV is turned ON.
Installer Menu (Cont.) Installer Menu Items 073 through 119 Menu Item 16 Function Value Range Default Value Brief Description of Function and Comments 073 CH NOT AVBLE 0/1 0 If set to 1 and Channel Override is 0, “NOT AVAILABLE” message is displayed when directly accessing a channel not in the favorite Channel List. 075 REVERT CH 0/1 0 If set to 1 and loss of MPI communication occurs, TV tunes to Start Channel. 078 UPN MSB 0 ~ 255 0 User programmable number, most significant byte.
Installer Menu (Cont.) Detailed Descriptions of Installer Menu Items 000 - INSTALLER SEQUENCE Speci es entry sequence to the Installer Menu. 0 = 9876 2 = 1478 To translate a TV volume level to the Installer Menu value, use the following formula: 1 = 4321 3 = 3698 001 - POWER MANAGE (Power Management) Determines hours of no activity before automatic shutoff. The Power Management function is for saving energy. If set to 0, Power Manage is Off.
Installer Menu (Cont.) 015 - SLEEP TIMER If set to 1, the Sleep Timer feature may be used. If set to 0, the Sleep Timer is not available. 016 - EN TIMER (Enable On/Off Timers) * If set to 1, the Timer function is available to the end user and enabled continuously. Set to 0 to disable On/Off timers. Note: Clock must be set in order to use timers. 017 - ALARM * Gives the installer the option of making the Alarm function available to the end user. If set to 1, the Alarm function is available to the end user.
Installer Menu (Cont.) 069 - EN. CH-T COL. (Enable Channel-Time Custom Color) Set to 1 to enable custom color for the Channel-Time display. Set to 0 to disable custom color for the Channel-Time display. 070 - FOR. CH-TIME (Channel-Time Display Foreground Color) Set according to Color Chart: 0 = Black 3 = Cyan 6 = Yellow 1 = Blue 4 = Red 7 = White 2 = Green 5 = Violet Note: Applies only to “Channel Not Available” message if item 073 is set to 1 (enabled).
Installer Menu (Cont.) 099 - BACK LIGHTING Sets the TV screen brightness at power up. Default setting is 100. • 1 - 100 Static Back Lighting (1 = Dimmest picture, 100 = Brightest picture) • 101 - 200 Dynamic Back Lighting (101 = Dimmest picture, 200 = Brightest picture) If set between 101 and 200, the TV automatically controls back lighting depending upon the picture level of the current program. If set to 255, back lighting is controlled via the Picture settings in the TV’s setup menus.
TV Setup Menus Overview On-screen setup menus control the features of the TV. Press MENU on the Installer Remote to access the TV setup menus, and set the TV features to the desired configuration for the end user. CHANNEL PICTURE AUDIO TIME LOCK OPTION INPUT MY MEDIA Refer to the Owner’s Manual for further information on the TV setup menus.
Adding Channel Label Icons / Custom Channel Labels (2-5-4 + MENU Mode) Editing/Adding Channel Icons and/or Labels If there is no pre-assigned icon, you can make a custom channel label of up to seven (7) characters to help identify a channel or network. If desired, channel labels can also be added in addition to a pre-assigned icon. You may also add labels for the Aux input sources to clearly identify the devices that are connected to the Aux inputs.
Cloning Overview / Clonable Menu Features IMPORTANT CLONING INFORMATION There are three options for cloning a Master TV Setup: • Using a USB memory device • Using a TLL-1100A clone programmer • Using a LT2002 clone programmer Each option is described in further detail on the pages that follow. As you perform cloning procedures, be sure to complete each task as indicated. If a procedure or step is omitted or not performed completely, cloning may not work.
Cloning Procedures Learning / Teaching a Master TV Setup using a USB Memory Device USB Cloning Notes • Read the IMPORTANT CLONING INFORMATION on page 23 before beginning any cloning procedures. • You may edit a lename as part of the Learning procedure; however, a le with edited contents will not be recognized. • It is not possible to clone a Master TV’s clock using a USB memory device. Either set a Target TV’s clock manually, or use the Auto Clock setting in the TV setup menus.
Cloning Procedures (Cont.) Learning / Teaching a Master TV Setup using a TLL-1100A Clone Programmer Warning: Do not connect a clone programmer to a PPV card installed in the Master or Target TVs, as this will damage the clone programmer and the PPV card. TLL-1100A Cloning Notes • Read the IMPORTANT CLONING INFORMATION on page 23 before beginning any cloning procedures. • Ensure the TLL-1100A is either fully charged or connected to AC power.
Cloning Procedures (Cont.) Learning / Teaching a Master TV Setup using a TLL-1100A Clone Programmer (Cont.) (Optional) Set the Clock Set the time on a Master TV’s clock. (If the time has already been copied from a TV into the TLL-1100A clone programmer, you can set the Master TV’s clock by copying the time from the clone programmer.) The TLL-1100A can copy the current time to both a Master TV and to the clone’s internal clock— accurate to within one minute.
Cloning Procedures (Cont.) Learning / Teaching a Master TV Setup using an LT2002 Clone Programmer Warning: Do not connect a clone programmer to a PPV card installed in the Master or Target TVs, as this will damage the clone programmer and the PPV card. Cloning is accomplished using the TV/clone programmer MPI ports for communication (see figure). LT2002 Cloning Notes • Read the IMPORTANT CLONING INFORMATION on page 23 before beginning any cloning procedures.
Cloning Procedures (Cont.) Learning / Teaching a Master TV Setup using an LT2002 Clone Programmer (Cont.) (Continued from previous page) 6. Once you select the clone Memory Bank, press ENTER on the Installer Remote. The Memory Bank you selected will be shown. 7. Press POWER to transfer the Master TV Setup into the selected Memory Bank on the LT2002. Learning usually takes about 90 seconds. “LEARNING IN PROGRESS” will be displayed on the screen while the LT2002 copies the Master Setup.
FTG Mode of Operation FTG Mode Overview / Determining the TV Operating Mode FTG Mode Overview FTG Mode enables Pro:Idiom decryption and also allows logical channel mapping of physical channels. “Teaching” an FMA Configuration file to a LD310H TV puts the TV into FTG Mode. Once the LD310H TV is in FTG Mode: • Users can still access the Installer Menu; however, all Installer Menu items, with the exception of item 117 FACT DEFAULT will be read-only.
FTG Mode of Operation (Cont.) Creating an FMA Configuration File using the FTG Configuration Application In order to enable Pro:Idiom decryption, it is recommended that you create an FMA Con guration le using the FTG Con guration Application. However, if you do not know the RF channels at the site, you can Learn an FMA Con guration le from a TV (see next page). The procedure below provides an overview of the steps required to create an FMA Configuration (.fma) file.
FTG Mode of Operation (Cont.) Teaching FMA Configuration to a TV / Learning an FMA Configuration File from a TV Teaching FMA Configuration to a TV 1. Plug the USB memory device that contains the FMA Con guration le into the Target LD310H TV USB IN port. 2.
FTG Mode of Operation (Cont.) Optional Manual Configuration / Setup for a TV The manual configuration procedures below should only be performed if you do not know the RF channels at the site and need to Learn the FMA Configuration file from an LD310H TV. Set Installer Menu Items These steps provide speci c instruction only on the Installer Menu items that should be set on an LD310H TV. Refer to pages 14 to 20 for detailed information on all Installer Menu items. 1. Make sure the TV is ON.
FTG Mode of Operation (Cont.) FTG Channel Map Configuration Utility Overview The FTG Channel Map Configuration Utility enables you to build a Channel Map with logical channel numbers. Note: Write, Read, and Learn functions in the FTG Channel Map Configuration Utility are used for local FTG configuration of TVs that support a direct connection to a PC. These functions are not applicable to the process of creating an FMA Configuration file to be used with LD310H TVs.
FTG Mode of Operation (Cont.) FTG Channel Map Editor Overview The FTG Channel Map Editor shows a single Logical Channel’s Data and the FTG Channel Map. LOGICAL CHANNEL MAPPING Select a Logical Channel number, then assign it the RF, Major, and Minor channel numbers to complete the mapping. CUSTOM CHANNEL LABELS/ICONS Enter custom labels and select icons by name on menu or by number. DELETE Click to remove highlighted channel from FTG Channel Map.
FTG Mode of Operation (Cont.) FTG Installer Menu Configuration Utility Overview Note: Write, Read, Learn, and IR Remote Access functions in the FTG Installer Menu Configuration Utility are used for local FTG configuration of TVs that support a direct connection to a PC. These functions are not applicable to the process of creating an FMA Configuration file to be used with LD310H TVs. CONFIGURATION SETTINGS Select tabs for categories of Installer Menu items to set up TV.
FTG Mode of Operation (Cont.) FMA Configuration Utility Overview Note: FMA Write, Read, Clock, Broadcast, Firmware, and IP Communication functions in the FMA Configuration Utility are used to configure control equipment (Example: FMA-LG101) at the hotel/institution head end. These functions are not applicable to the process of creating an FMA Configuration file to be used with LD310H TVs.
Reference: Upgrading TV/PTC Software using a USB Memory Device Checking the Software Versions Note: This function is not accessible while the TV is in FTG or PPV Mode. You can check the software versions of the TV by accessing the Installer Menu with the Installer Remote: Press MENU repeatedly until the on-screen setup menus lock up, and then press 9-8-7-6 + ENTER. When you are finished, press ENTER again to exit the Installer Menu.
Reference: Downloading a Splash Screen using a USB Memory Device Splash Screen Image File Guidelines USB Download Menu • The splash screen image must be a baseline (not progressive) JPEG. Upgrade TV Software • The image should be no larger than 1 MB. Upgrade PTC Software • The ideal size for the image is 1366 x 768 pixels or under. • The image le must be stored in a folder named “LG_DTV” in the root directory of USB memory device. • Ensure the USB device has been formatted with FAT format.
Reference: Power Consumption Settings The following tables assume Installer Menu item 099 BACK LIGHTING is set as shown below (default value is 100). 32LD310H Item 099 Back Lighting (Static) Power Consumption (Watts) 37LD310H Percent Savings Power Consumption (Watts) Percent Savings 100 72.97 0.00% 88.92 0.00% 90 80 70 60 50 40 30 20 10 1 63.82 58.53 53.58 44.24 41.27 38.71 36.20 33.51 31.01 28.55 12.54% 19.78% 26.57% 39.38% 43.45% 46.95% 50.39% 54.07% 57.51% 60.87% 84.19 77.84 72.19 66.
Reference: TV Camport Auto Sense Operation The Camport Auto Sense function is enabled when: 1. Installer Menu item 034 CAMPORT EN is set to 1 AND 2. Installer Menu item 040 AUTO CAMPORT is enabled (1). Selectable: Can be accessed with INPUT key, direct access, etc. Auto Sense: TV switches to this input when connector is inserted. The Camport (Side [AV IN 2] Video) has the highest priority and will override any commands including tuning to the Start Channel.
Reference: TV Aux Input Configuration ENABLE DIRECT ACCESS Tuning TV Installer Menu MPI DATA MPI DATA STATUS TYPE 0x41 SOURCES ENABLED (R/W) DATA STATUS TYPE 0xD2 CURRENT AV SOURCE (R) DATA STATUS TYPE 0x0D AUX SOURCE (R) START AUX SOURCE ASSIGNMENT OLD_ OCV = 0 OLD_ OCV = 1 Source Input Source Mode Number Labeling Value Labeling Value Labeling 130 90 Video2 (Side) CV 34 CAMPORT_EN 0x01 Video Front (Camport) 0 Video Front (Camport) 0 (VIDEO) 2 131 91 Video1 (Rear) CV 39 RE
Troubleshooting General Troubleshooting Some Quick and Easy Tips for Resolving Problems Symptom Possible Cause(s) Possible Solution(s) Channel not included in channel lineup in TV controller. After 2-5-5 + MENU, only channels included in TV controller will appear. If channel is available, it can be added to channel lineup. If it is not available, the “No Signal” message appears on the TV screen. Software Problems Cannot direct enter channel number or “No Signal” appears. Power No power.
Troubleshooting (Cont.) Troubleshooting Flow Chart Controller Quick Check STATUS LED on PTC Board blinking? No TV connected to AC Power? No Plug into AC Power outlet. Yes Yes Bad TV Cycle the power by removing and reconnecting the AC Power cord. Then, observe POWER LED on front of TV. POWER LED lit? No Bad Analog or Digital Board Yes No Bad TV No Bad PPV Card Yes Press POWER on Installer Remote. TV turned ON? TV responded? Press VOLUME UP/ DOWN or MUTE key on User-supplied Remote.
Troubleshooting (Cont.) Commercial Mode Check / FTG Operation Troubleshooting Commercial Mode Check Press POWER on Installer Remote. TV responded? No Bad TV Yes Leave the TV set ON. Go to Installer Menu by pressing MENU until the on-screen setup menus lock up (i.e., stop responding). TV stopped responding or continued to respond? Stopped responding TV is in Commercial Mode. Continued to respond TV is not in Commercial Mode. Call Technical Support for assistance.
Troubleshooting (Cont.) Clone Programmer Troubleshooting Warning: Do not connect a clone programmer to a PPV card installed in the Master or Target TVs, as this will damage the clone programmer and the PPV card. Reset Clone Programmer After Static Shock After replacing exhausted batteries (LT2002 only), or if the clone programmer behaves strangely after a static shock: • TLL-1100A: Turn the TLL-1100A OFF and then ON.
Glossary of Terms A list of de nitions for some of the words found in this guide. 75 OHM RF CABLE The wire that comes from an off-air antenna or cable service provider. The end looks like a hex-shaped nut with a wire through the middle. It screws onto the Antenna/Cable threaded jack on the back of the TV. 300 TO 75 OHM ADAPTER A small device that connects a 2-wire 300 ohm antenna to a 75 ohm RF jack.
Document Revision History / Notes Document Revision History Date Description January 2011 Revision A: New Document Product documentation is available online at: www.LGsolutions.com/products. From the Products page, select TVs, Systems & Solutions, then LCD TVs, then the applicable TV. Click the Literature & Downloads tab at the bottom of the TV page, and select the required document(s) from the Downloads list.
For Customer Support/Service, please call: 1-888-865-3026 www.LGsolutions.com Pro:Idiom is a registered trademark of Zenith Electronics LLC. Pro:Centric is a trademark of LG Electronics U.S.A., Inc. All other trademarks or registered trademarks are the property of their respective owners. © Copyright 2011, LG Electronics U.S.A., Inc.
26LD340H 32LD340H 37LD340H 42LD340H 26LD345H 32LD345H 37LD345H 42LD345H Lodging Guest Interactive Pro:Centric™ TVs Commercial Mode Setup Guide Note: Selected features shown in this guide may not be available on all models. EXPERIENCED INSTALLER Commercial Mode Setup pages 12 – 13 Cloning Information pages 23 – 28 FTG Mode of Operation pages 29 – 39 © Copyright 2011, LG Electronics U.S.A., Inc.
For Customer Support/Service, please call: 1-888-865-3026 The latest product information and documentation is available online at: www.LGsolutions.com/products MODEL and SERIAL NUMBER The model and serial numbers of this TV are located on the back of the cabinet. For future reference, LG suggests that you record those numbers here: Model No._________________ Serial No.
IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources, such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
IMPORTANT SAFETY INSTRUCTIONS (Continued from previous page) 22. Outdoor Antenna Grounding If an outside antenna or cable system is connected to the product, follow the precautions below. An outdoor antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits or where it can come into contact with such power lines or circuits as death or serious injury can occur.
Table of Contents Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 FTG Mode via EBL . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Important Safety Instructions . . . . . . . . . . . . . . . . . . . .3 – 4 FTG Configuration Application Utilities Overview . . 36 – 39 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 FTG Channel Map Configuration Utility . . . . . . . . . . . .
Setup Checklist / Overview Setup Checklist Installation and Setup Checklist __ Unpack TV and all accessories. __ Install batteries in remote control. __ Install TV on VESA mount or stand. Note: It may be advisable to make all cable connections before installing on VESA mount or stand, as appropriate. Hardware Connections __ Install any additional hardware as appropriate to your institution, LAN, etc.
Pro:Centric TV Interactive Menu Features Important: Pro:Centric operation requires that Installer Menu items 098 PRO:CENTRIC and 119 DATA CHANNEL be set appropriately and that the TV be in PPV or FTG Mode. The interactive Pro:Centric TV enables guests—from the comfort of their hotel rooms—to view and select from a complete listing of hotel services and amenities. The Pro:Centric TV is connected to the hotel's billing computer, and service/amenities charges are billed at the time of order.
LD340H/LD345H Rear Jack Panel AUDIO IN (RGB/DVI) Audio connection for RGB or DVI device. RJP Connection for Remote Jack Pack (RJP) Control cable. REMOTE CONTROL OUT IR output for controlling an auxiliary device. UPDATE Restricted to software updates. RESET Press RESET to re-initialize the TV. AUDIO/VIDEO IN 1 Connection for composite audio/ video output from external device. RS-232C IN (SERVICE ONLY) RESET HDMI HDMI /DVI IN 2 1 UPDATE .......... .......... ..... .... RJP REMOTE CONTROL OUT ..
Side Connections Panel / RF Antenna Connection USB IN Side Connections Panel USB IN Insert USB memory device for software updates, cloning purposes, or picture/music entertainment, as applicable. A/V 2 Input VIDEO L/MONO -AUDIO- R L/MONO-AUDIO-R IN Connect to audio output jacks on external device. For only mono audio output, connect to Left audio input. VIDEO IN Connect to video output port on external device (see Reference section, “TV Camport Auto Sense Operation,” for further information).
Installer Overview This is the Commercial Mode Setup Guide only. Installer Menu / Commercial Mode Setup xxLD340H PTC INSTALLER MENU To set up a Master TV for cloning purposes, you will need to know how to enter the TV Installer Menu and make changes to the default values as required. Similarly, to configure a TV’s Installer Menu settings in FTG Mode, you will need to know how to access and use the FTG Configuration Application utilities.
Installer Remote Control Typical Key Functions The LG Installer Remote illustrated below and throughout this document shows typical remote control functions and is provided for reference only. This Installer Remote may vary from the Installer Remote supplied with the TV. POWER Turns TV ON or OFF. ALARM Sets the time when the TV will automatically turn itself ON. TIMER Sets the amount of time before the TV automatically turns itself OFF.
Commercial Mode Setup for Master TV This section describes how to set up a Master TV for cloning purposes when the TV is in Pass-through Mode. Note: Disconnect all Aux inputs. Under certain conditions, Auto Tuning (Channel Search) is disabled if there is an Aux input active. Note: Refer to FTG Mode information on pages 29 to 39 for details on entering FTG Mode and configuring/editing FTG Channel Map and FTG Installer Menu settings using the FTG Configuration Application. 1. Set Installer Menu items.
Commercial Mode Setup for Master TV (Cont.) (Continued from previous page) 3. Run Auto Tuning (Channel Search). (continued) b) Use the Channel Edit option in the Channel Menu to edit the channel lineup, as necessary, to include free to guest channels only. • Add/delete channels per your system requirements.
Installer Menu Use the Installer Menu to set up or change operational settings. Refer to the table starting on the next page for brief descriptions of Installer Menu items. More detailed descriptions follow the table listing. Accessing the Installer Menu 1. Make sure the TV is ON. 2. Using an Installer Remote, press MENU repeatedly until the on-screen setup menus lock up, and then press 9-8-7-6 + ENTER to access the Installer Menu. The Installer Menu opens with item 000 INSTALLER SEQ 000.
Installer Menu (Cont.) Installer Menu Items 000 through 071 Menu Item Function Value Range Default Value Brief Description of Function and Comments 000 INSTALLER SEQ 0~3 0 Leave default set to 0. 001 POWER MANAGE 0~7 0 Sets number of hours of no activity before automatic shutoff. 002 AC ON 0/1 0 Set to 1 to enable Auto Turn ON when AC power is applied. 003 BAND/AFC 0~3 1 Selects Tuning Band: 0=Broadcast, 1=CATV, 2=HRC, 3=IRC 0 ~ 127, 255 255 Channel tuned when TV is turned ON.
Installer Menu (Cont.) Installer Menu Items 073 through 119 Menu Item 16 Function Value Range Default Value Brief Description of Function and Comments 073 CH NOT AVBLE 0/1 0 If set to 1 and Channel Override is 0, “NOT AVAILABLE” message is displayed when directly accessing a channel not in the favorite Channel List. 075 REVERT CH 0/1 0 If set to 1 and loss of MPI communication occurs, TV tunes to Start Channel. 078 UPN MSB 0 ~ 255 0 User programmable number, most significant byte.
Installer Menu (Cont.) Detailed Descriptions of Installer Menu Items 000 - INSTALLER SEQUENCE Specifies entry sequence to the Installer Menu. 0 = 9876 2 = 1478 To translate a TV volume level to the Installer Menu value, use the following formula: 1 = 4321 3 = 3698 001 - POWER MANAGE (Power Management) Determines hours of no activity before automatic shutoff. The Power Management function is for saving energy. If set to 0, Power Manage is Off.
Installer Menu (Cont.) 015 - SLEEP TIMER If set to 1, the Sleep Timer feature may be used. If set to 0, the Sleep Timer is not available. 016 - EN TIMER (Enable On/Off Timers) * If set to 1, the Timer function is available to the end user and enabled continuously. Set to 0 to disable On/Off timers. Note: Clock must be set in order to use timers. 017 - ALARM * Gives the installer the option of making the Alarm function available to the end user. If set to 1, the Alarm function is available to the end user.
Installer Menu (Cont.) 047 - AUX STATUS Set to 1 for MPI Aux source to be reported as a channel number instead of channel 0. Set to 0 to disable Aux identification change. Controls MPI status channel response for Aux inputs. 082 - CHKSM ERROR (Checksum Error) Enforces rigid MPI checksum validation. Set to 1 for validation. Set to 0 to disable (does not check checksum on MPI async port). SPI is always checked. 053 - DIS.
Installer Menu (Cont.) • 6 = Scaler Model RJPs: DVI Mode Enables RJP feature for use with reduced cable bundle models. In this mode, when an HDMI/DVI source is connected to the RJP, only digital video is expected via the HDMI cable. Analog audio is provided via separate cable, from the source, connected to an RJP AUDIO IN. If no analog audio cable is connected, tuner audio will be heard. Notes: See Reference section, “RJP Model List and Input Auto-sensing Hierarchy.
TV Setup Menus Overview On-screen setup menus control the features of the TV. Press MENU on the Installer Remote to access the TV setup menus, and set the TV features to the desired configuration for the end user. CHANNEL PICTURE AUDIO TIME LOCK OPTION INPUT MY MEDIA Refer to the Owner’s Manual for further information on the TV setup menus.
Adding Channel Icons / Custom Channel Labels (2-5-4 + MENU Mode) Editing/Adding Channel Icons and/or Labels If there is no pre-assigned icon, you can make a custom channel label of up to seven (7) characters to help identify a channel or network. If desired, channel labels can also be added in addition to a pre-assigned icon. You may also add labels for the Aux input sources to clearly identify the devices that are connected to the Aux inputs.
Cloning Overview / Clonable Menu Features IMPORTANT CLONING INFORMATION There are three options for cloning a Master TV Setup: • Using a USB memory device • Using a TLL-1100A clone programmer • Using a LT2002 clone programmer Each option is described in further detail on the pages that follow. As you perform cloning procedures, be sure to complete each task as indicated. If a procedure or step is omitted or not performed completely, cloning may not work.
Cloning Procedures Learning / Teaching a Master TV Setup using a USB Memory Device USB Cloning Notes • Read the IMPORTANT CLONING INFORMATION on page 23 before beginning any cloning procedures. • You may edit a filename as part of the Learning procedure; however, a file with edited contents will not be recognized. • It is not possible to clone a Master TV’s clock using a USB memory device. Either set a Target TV’s clock manually, or use the Auto Clock setting in the TV setup menus.
Cloning Procedures (Cont.) Learning / Teaching a Master TV Setup using a TLL-1100A Clone Programmer Warning: Do not connect a clone programmer to a PPV card installed in the Master or Target TVs. Also, if the TV is in LodgeNet PPV Mode (check with the site administrator if you are not certain), do not connect a clone programmer to the GAME CONTROL/MPI port. Either of these actions will damage the clone programmer and, if applicable, the PPV card.
Cloning Procedures (Cont.) Learning / Teaching a Master TV Setup using a TLL-1100A Clone Programmer (Cont.) (Optional) Set the Clock Set the time on a Master TV’s clock. (If the time has already been copied from a TV into the TLL-1100A clone programmer, you can set the Master TV’s clock by copying the time from the clone programmer.) The TLL1100A can copy the current time to both a Master TV and to the clone’s internal clock—accurate to within one minute.
Cloning Procedures (Cont.) Learning / Teaching a Master TV Setup using an LT2002 Clone Programmer Warning: Do not connect a clone programmer to a PPV card installed in the Master or Target TVs. Also, if the TV is in LodgeNet PPV Mode (check with the site administrator if you are not certain), do not connect a clone programmer to the GAME CONTROL/MPI port. Either of these actions will damage the clone programmer and, if applicable, the PPV card.
Cloning Procedures (Cont.) Learning / Teaching a Master TV Setup using an LT2002 Clone Programmer (Cont.) (Continued from previous page) 6. Verify the Learning setup information on the next screen, and then press POWER to transfer the Master TV Setup into the selected Memory Bank on the LT2002. Learning usually takes about 90 seconds. “LEARNING IN PROGRESS” will be displayed on the screen while the LT2002 copies the Master Setup.
FTG Mode of Operation Overview FTG Mode via CPU or EBL FTG Mode enables Pro:Idiom decryption and also allows logical channel mapping of physical channels. There are two separate and distinct methods for configuring LD340H/LD345H TVs for FTG Mode of operation: one (new) method is to configure the TV CPU for FTG Mode operation, while the other is to configure the TV EBL for FTG Mode operation. EACH OF THESE METHODS IS MUTUALLY EXCLUSIVE. IF THE CPU IS IN FTG MODE, THE EBL CANNOT BE SWITCHED TO FTG MODE.
FTG Mode of Operation Overview (Cont.) Determining the TV Operating Mode To determine the operating mode of the TV, press MENU on the Installer Remote. The menu display alternates based on the operating mode. See examples below. If the end user Function Menu appears, the TV is in FTG Mode. If the TV setup menus appear, the TV is in Pass-through Mode. ASPECT RATIO Move Function Menu Indicates the TV (CPU or EBL) is in FTG Mode.
FTG Mode via CPU Creating an FMA Configuration File using the FTG Configuration Application This section describes how to create an FMA Configuration file that can be saved to a USB memory device. In order to enable Pro:Idiom decryption, it is recommended that you create an FMA Configuration file using the FTG Configuration Application.
FTG Mode via CPU (Cont.) Teaching FMA Configuration to a TV This procedure describes how to “Teach” an FMA Configuration file from a USB memory device to a TV. Ensure you have completed the procedure on the previous page to create the FMA Configuration file before proceeding with the steps below. Caution: If the TV EBL is already in FTG Mode, you cannot use this procedure to make changes to the FTG Channel Map and FTG Installer Menu settings.
FTG Mode via CPU (Cont.) Learning an FMA Configuration File from a TV To ensure that Pro:Idiom decryption is enabled, it is recommended that you create an FMA Configuration file using the FTG Configuration Application as described on page 31. However, if necessary, this option enables you to save (Learn) an FMA Configuration file from an LD340H/LD345H TV to a USB memory device.
FTG Mode via CPU (Cont.) Optional Manual Configuration / Setup for a TV The manual configuration procedures below should only be performed if you do not know the RF channels at the site and need to “Learn” an FMA Configuration file from an LD340H/LD345H TV as described on the previous page. Ensure the TV is in Pass-through Mode before you begin. Set Installer Menu Items These steps provide specific instruction only on the Installer Menu items that should be set on an LD340H/LD345H TV.
FTG Mode via EBL The following steps outline local FTG configuration of individual TV EBLs using a direct PC-to-TV connection. Refer to the Free-To-Guest (FTG) Configuration Application manual for further information. See also FTG Configuration Application sample screens on pages 36 to 38. Note: FTG Configuration Application software is available online at: www.LGcommercial.com/FTGsoftware.
FTG Configuration Application Utilities Overview FTG Channel Map Configuration Utility The FTG Channel Map Configuration Utility enables you to build a Channel Map with logical channel numbers. Note: Write, Read, and Learn functions in the FTG Channel Map Configuration Utility are used for direct PC-to-TV FTG configuration of LD340H/LD345H TVs (FTG Mode via EBL). These functions are not applicable to the process of creating an FMA Configuration file to be saved to a USB memory device (FTG Mode via CPU).
FTG Configuration Application Utilities Overview (Cont.) FTG Channel Map Editor The FTG Channel Map Editor shows a single Logical Channel’s Data and the FTG Channel Map. LOGICAL CHANNEL MAPPING Select a Logical Channel number, then assign it the RF, Major, and Minor channel numbers to complete the mapping. CUSTOM CHANNEL LABELS/ICONS Enter custom labels and select icons by name on menu or by number. DELETE Click to remove highlighted channel from FTG Channel Map.
FTG Configuration Application Utilities Overview (Cont.) FTG Installer Menu Configuration Utility Note: Write, Read, Learn, and IR Remote Access functions in the FTG Installer Menu Configuration Utility are used for direct PC-to-TV FTG configuration of LD340H/LD345H TVs (FTG Mode via EBL). These functions are not applicable to the process of creating an FMA Configuration file to be saved to a USB memory device (FTG Mode via CPU).
FTG Configuration Application Utilities Overview (Cont.) FMA Configuration Utility Note: FMA Write, Read, Clock, Broadcast, Firmware, and IP Communication functions in the FMA Configuration Utility are used to configure b-LAN enabled equipment (Example: FMA-LG101) at the hotel/ institution head end. These functions are not applicable to the process of creating an FMA Configuration file to be used with LD340H/LD345H TVs (FTG Mode via CPU).
Remote Jack Pack / TV Connections & Setup Remote Jack Pack Setup RJP Available? If you will use a Remote Jack Pack (RJP) in your system, set Installer Menu item 093 RJP AVAILABLE appropriately (for example, on a legacy model RJP: HDMI Mode, set RJP AVAILABLE to 001). See Installer Menu detailed descriptions for further information. 093 RJP AVAILABLE 001 TV Connections Make these connections ONLY after Commercial Mode Setup and TV Cloning procedures are complete.
Reference: Upgrading TV/PTC Software using a USB Memory Device Checking the Software Versions xxLD340H PTC INSTALLER MENU You can check the software versions of the TV by accessing the Installer Menu with the Installer Remote: Press MENU repeatedly until the on-screen setup menus lock up, and then press 9-8-7-6 + ENTER. When you are finished, press ENTER again to exit the Installer Menu. 000 INSTALLER SEQ UPN 000-000-000-000 PTC V1.00.001 PTC Version Typical Installer Menu 000 ASIC 20E7 CPU V3.25.
Reference: Downloading a Splash Screen using a USB Memory Device TV S TV Software Update (Expert) The followin Select the fi or press EX Splash Screen Image File Guidelines USB Download Menu • The splash screen image must be a baseline (not progressive) JPEG. Upgrade TV Software • The image should be no larger than 1 MB. Upgrade PTC TVSoftware Software Update • The ideal size for the image is 1366 x 768 pixels or under.
Reference: Power Consumption Settings The following tables assume that Installer Menu item 118 POWER SAVINGS is set to 003 (default) and Installer Menu item 099 BACK LIGHTING is set as shown below (default value is 100). 26LD340H / 26LD345H Item 099 Back Lighting (Static) 32LD340H / 32LD345H Power Consumption (Watts) Percent Savings Power Consumption (Watts) 100 56.82 0.00% 90 80 70 60 50 40 30 20 10 1 51.98 47.09 42.06 39.71 37.36 36.31 35.12 32.59 30.23 27.95 8.52% 17.13% 25.97% 30.12% 34.
Reference: TV Camport Auto Sense Operation The Camport Auto Sense function is enabled when: 1. Installer Menu item 034 CAMPORT EN is set to 1 AND 2. Installer Menu item 040 AUTO CAMPORT is enabled (1). Selectable: Can be accessed with INPUT key, direct access, etc. Auto Sense: TV switches to this input when connector is inserted. The Camport (Side [AV IN 2] Video) has the highest priority and will override any commands including tuning to the Start Channel.
Reference: TV Aux Input Configuration ENABLE DIRECT ACCESS Tuning TV Installer Menu MPI DATA MPI DATA STATUS TYPE 0x41 SOURCES ENABLED (R/W) DATA STATUS TYPE 0xD2 CURRENT AV SOURCE (R) DATA STATUS TYPE 0x0D AUX SOURCE (R) START AUX SOURCE ASSIGNMENT OLD_ OCV = 0 OLD_ OCV = 1 Source Input Source Mode Number Labeling Value Labeling Value Labeling 130 90 Video2 (Side) CV 34 CAMPORT_EN 0x01 Video Front (Camport) 0 Video Front (Camport) 0 (VIDEO) 2 131 91 Video1 (Rear) CV 39 RE
Reference: b-LAN Setup & Overview The b-LAN module is internal to the TV. It allows hotel/institution head end equipment with b-LAN technology to communicate, via the institution’s RF distribution system, with the TV for configuration and control. Note: MPI cards with b-LAN technology—LMT7Z5, LMT7Z7, LMT7Z9—are NOT supported in TVs in which b-LAN technology is already integrated. Power to the b-LAN module is controlled by Installer Menu item 118 POWER SAVINGS.
Reference: RJP Model List and Input Auto-sensing Hierarchy RJP Model List Legacy Models Scaler Models RJP-101M N/A RJP-101ML N/A RJP-110F RJP-210F RJP-110FW RJP-210FW RJP-110W RJP-210W RJP-110WBR RJP-210WBR RJP-110S RJP-210S RJP-120G RJP-220G RJP-120T RJP-220T RJP-201B RJP-301B RJP-202B RJP-302B RJP Input Auto-sensing Hierarchy 206-4186 Priority Video Audio 1st (Highest) Digital Video In Audio In (3.
Resetting a TV to Pass-through Mode This section describes how you can reset a TV that is currently in FTG Mode to Pass-through Mode. Note that the reset to Pass-through Mode will also restore all factory default settings on the TV. FTG Mode via CPU There are three options for resetting Pass-through Mode on TVs that are in FTG Mode via the CPU.
Troubleshooting General Troubleshooting Some Quick and Easy Tips for Resolving Problems Symptom Possible Cause(s) Possible Solution(s) Channel not included in channel lineup in internal TV controller (PTC). After 2-5-5 + MENU, only channels included in the TV PTC will appear. If a channel is available, it can be added to channel lineup. If it is not available, the “No Signal” message appears on the TV screen. Software Problems When direct enter channel number, “No Signal” appears. Power No power.
Troubleshooting (Cont.) Troubleshooting Flow Chart Controller Quick Check STATUS LED on PTC Board blinking? No TV connected to AC Power? No Plug into AC Power outlet. Yes Yes Bad TV Cycle the power by removing and reconnecting the AC Power cord. Then, observe POWER LED on front of TV. POWER LED lit? No Bad Analog or Digital Board Yes No Bad TV No Bad PPV Card Yes Press POWER on Installer Remote. TV turned ON? TV responded? Press VOLUME UP/ DOWN or MUTE key on User-supplied Remote.
Troubleshooting (Cont.) Commercial Mode Check / FTG Operation Troubleshooting Commercial Mode Check Press POWER on Installer Remote. TV responded? No Bad TV Yes Leave the TV set ON. Go to Installer Menu by pressing MENU until the on-screen setup menus lock up (i.e., stop responding). TV stopped responding or continued to respond? Stopped responding TV is in Commercial Mode. Continued to respond TV is not in Commercial Mode. Call Technical Support for assistance.
Troubleshooting (Cont.) Clone Programmer Troubleshooting Warning: Do not connect a clone programmer to a PPV card installed in the Master or Target TVs. Also, if the TV is in LodgeNet PPV Mode (check with the site administrator if you are not certain), do not connect a clone programmer to the GAME CONTROL/MPI port. Either of these actions will damage the clone programmer and, if applicable, the PPV card.
Glossary of Terms A list of definitions for some of the words found in this guide. 75 OHM RF CABLE The wire that comes from an off-air antenna or cable service provider. The end looks like a hex-shaped nut with a wire through the middle. It screws onto the Antenna/Cable threaded jack on the back of the TV. 300 TO 75 OHM ADAPTER A small device that connects a 2-wire 300 ohm antenna to a 75 ohm RF jack.
Document Revision History / Notes Document Revision History Date Description May 2011 Revision A: New document Product documentation is available online at: www.LGsolutions.com/products. From the Products page, select TVs, Systems & Solutions, then LCD TVs, then the applicable TV. Click the Literature & Downloads tab at the bottom of the TV page, and select the required document(s) from the Downloads list.
For Customer Support/Service, please call: 1-888-865-3026 www.LGsolutions.com Pro:Idiom is a registered trademark of Zenith Electronics LLC. Pro:Centric is a trademark of LG Electronics U.S.A., Inc. b-LAN is a trademark of LodgeNet Interactive Corporation. All other trademarks or registered trademarks are the property of their respective owners. © Copyright 2011, LG Electronics U.S.A., Inc.