ENGLISH ESPAÑOL INSTALLATION MANUAL GAS DOUBLE OVEN RANGE Please read this guide thoroughly before installation. LDG3017ST LDG3016ST LDG3015ST/SB/SW LDG3011ST LDG3037ST LDG3036ST LDG3035ST/SB/SW LDG3031ST LDG3036BD www.lg.com MFL62177703 (REV.
INSTALLATION INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE INSTALLATION INSTALLATION SAFETY INSTRUCTIONS BEFORE YOU BEGIN Read these instructions completely and carefully. Installation of this range must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA.54, latest edition. In Canada, installation must conform with the current Natural Gas Installation Code, CAN/CGAB149.1 or the current Propane Installation Code, CAN/CGA-B149.
INSTALLATION INSTRUCTIONS ENGLISH READ ALL INSTRUCTIONS BEFORE INSTALLATION INSTALLATION SAFETY INSTRUCTIONS (continued) BEFORE YOU BEGIN Remove all tape and packing materials before using the range. Dispose of all plastic bags after unpacking the range. Never allow children to play with packing materials. IMPORTANT SAFETY INSTRUCTIONS Read these instructions completely and carefully. Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage.
INSTALLATION INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE INSTALLATION INSTALLATION SAFETY INSTRUCTIONS (continued) WARNING! •A LL RANGES CAN TIP • I NJURY TO PERSONS COULD RESULT • I NSTALL ANTI-TIP DEVICES PACKED WITH RANGE •S EE INSTALLATION INSTRUCTIONS • DO NOT step or sit on the door. Install the AntiTip Bracket packed with range. - The range could be tipped and injury might result from spilled hot liquid, food, or the range itself. WARNING! • NEVER reuse old flexible connectors.
INSTALLATION INSTRUCTIONS ENGLISH READ ALL INSTRUCTIONS BEFORE INSTALLATION INSTALLATION SAFETY INSTRUCTIONS (continued) WARNING! • If a 30” clearance between cooking surface and overhead combustible material or metal cabinets cannot be maintained, protect the underside of the cabinets above the cooktop with not less than 1/4” insulating millboard covered with sheet metal not less than 0.0122” thick. Clearance between the cooking surface and protected cabinets MUST NEVER BE LESS THAN 24 INCHES.
INSTALLATION INSTRUCTIONS DIMENSIONS AND CLEARANCES Provide proper clearances between the range and adjacent combustible surfaces. These dimensions must be met for safe use of your range. The location of the electrical outlet and pipe opening (see “GAS PIPE AND ELECTRICAL OUTLET LOCATIONS”) may be adjusted to meet specific requirements. The range may be placed with 0” clearance (flush) at the back wall.
INSTALLATION INSTRUCTIONS Do not locate your range where it may be subject to strong drafts. Any openings in the floor or wall behind the range should be sealed. Make sure the openings around the base of the range that supply fresh air for combustion and ventilation are not blocked by carpeting or woodwork. When the floor covering ends at the front of the range, the area that the range will be installed on should be built up with plywood to the same level or higher than the floor covering.
INSTALLATION INSTRUCTIONS GAS PIPE AND ELECTRICAL OUTLET LOCATIONS 30” 9 1/16” 113 /32” 2” Recommended area for 120V outlet on rear wall and area for throughthe wall connection of pipe stub and shut-off valve. 819/32” 3” 14 5/16” 23/8” Recommended area for throughthe floor connection of pipe stub and shut-off valve. 1. PROVIDE ADEQUATE GAS SUPPLY Your range is designed to operate at a pressure of 5” of water column on natural gas or 10” of water column on LP.
INSTALLATION INSTRUCTIONS Shut off the range gas supply valve before removing the old range and leave it off until the new hook-up has been completed. Because hard piping restricts movement of the range, the use of a CSA International-certified flexible metal appliance connector should be used unless local codes require a hard-piped connection. C Connect a flexible metal appliance connector to the adapter on the range. Position range to permit connection at the shut-off valve.
INSTALLATION INSTRUCTIONS 3. ELECTRICAL CONNECTIONS ELECTRICAL REQUIREMENTS 120 Volt, 60 Hertz, properly grounded dedicated circuit protected by a 15 or 20 Amp circuit breaker, or slow blow fuse. GROUNDING IMPORTANT: FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED. The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates with a standard 3-prong grounding wall receptacle to minimize the possibility of electric shock hazard from this appliance.
INSTALLATION INSTRUCTIONS ENGLISH 5. ASSEMBLE THE SURFACE BURNERS CAUTION DO NOT operate the burners without all parts in place. Place the burner caps and heads on the cooktop. Make sure that the caps and heads are placed in the correct locations. There is one small, one medium, one large and one extra large burner head and cap. Medium burner head and cap Large burner Front of range head and cap Electrode Make sure the hole in the burner head is positioned over the electrode.
INSTALLATION INSTRUCTIONS 7. ADJUST THE SURFACE BURNER TO THE LOW FLAME(SIMMER) SETTING. 1) Light all surface burners. 2) Turn the knob on the burner being adjusted to “LO”. 3) Remove knob. 4) Insert a small, flat bladed screwdriver into the valve shaft as shown in Fig. 1. On right front valve for model LDG3019ST there is a secondary adjustment for the low flame for the outer burners.
INSTALLATION INSTRUCTIONS To check ignition of the Bake burner, follow the steps below: To check ignition of the Broil burner, follow the steps below: 1) Remove all packing from inside the oven cavity. 2) Press "Bake" (350 will be shown in the display). 3) Press Start. 1) Press "Broil" ("Hi" will be shown in the display). 2) Make sure the door is closed. 3) Press Start. It may take between 30 and 90 seconds for the burner to start heating.
INSTALLATION INSTRUCTIONS 10. INSTALLING THE ANTI-TIP DEVICE WARNING INSTALL THE BRACKET USING THE BRACKET INSTALLATION SHEET Anti-tip bracket •R ange must be secured with an approved AntiWall plate Screw must enter wood or concrete Tip device. • T he range could be tipped by standing, sitting or leaning on an open door if the range or Anti-Tip device is not properly installed. •A fter installing the Anti-Tip device, verify that it is in place by carefully attempting to tilt the range forward.
INSTALLATION INSTRUCTIONS Make sure all controls are left in the off position. Make sure the flow of combustion and ventilation air to the range is unblocked. CONVERTING TO LP GAS (OR CONVERTING BACK TO NATURAL GAS FROM LP) This range leaves the factory set for use with natural gas. The conversion to LP gas must be performed by a qualified LP gas installer when converting to LP gas. The conversion instructions and LP orifices can be found attached to the range on the back.
Memo