INSTALLATION 11 INSTALLATION ENGLISH Installation Parts and Tools Parts not Provided Electrical cable Water supply tube Fittings for tube Coupler Teflon™ tape Air gap Wire nuts for 16-gauge wiring Hose clamp ⅞" UL approved strain relief Electrical tape Flat-blade screwdriver Phillips screwdriver Hole saw min.
12 INSTALLATION Installation Overview Preparing Cabinet Opening Leveling the Dishwasher Preparing Electrical Wiring Securing the Dishwasher to Countertop Preparing Water Supply Connection Connecting the Drain Hose Preparing the Dishwasher Connecting Water Supply Removing Lower Cover Connecting Power Sliding the Dishwasher into Cabinet Final Check Product Dimensions Back view Side view 26 5/8 - 26 13 /16" (676 - 681 mm) 23 3/4" (603 mm) 24 5/8" (625 mm) 33 5 /16" (846 mm) 4 1/2" (115 mm) 33
INSTALLATION 13 Preparing Cabinet Opening NOTE ••Do not push. 24" (610 mm) min. WARNING ••Do not remove safety cover. Removal can result in fire, electric shock or death. 33 5/8" (854 mm) min. 24" (610 mm) min. 1 Select a location as close to the sink as possible for easy connections to water and drain lines. 2 To ensure proper drainage, install the dishwasher no more than 12 ft. (3.65 m) from the sink.
14 INSTALLATION Preparing Electrical Wiring this appliance with the correct voltage 1 Operate as shown in this manual and on the rating plate. Connect it to a dedicated, properly grounded branch circuit which is protected by a time delay fuse. Connect the appliance using 3-wires, including a ground wire. 2 3 4 If an outlet and other power connector are used, it should be in an accessible location adjacent to and not behind the dishwasher and within 4 ft (1.2 m) of the dishwasher's side.
INSTALLATION 15 Preparing Dishwasher NOTE ••Do not push. The rear shipping brace can be removed if additional clearance is needed when installing the dishwasher under a low countertop. WARNING ••Do not remove safety cover. Removal can result in fire, electric shock or death. NOTE ••Do not pull or lift the dishwasher using the handle; doing so can damage the door and hinges. Open the door and grab the body frame and the top front opening of the tub to move or lift the dishwasher.
16 INSTALLATION Attaching Mounting Hardware For countertops made of wood or other material that will not be damaged by drilling, use the metal installation brackets. 1 Insert the installation brackets into the slots in the upper frame. 2 1 Sliding Dishwasher into Cabinet the dishwasher carefully into the cabinet 1 Slide opening. 2 Make sure the drain hose inside the cabinet is not kinked or pinched.
INSTALLATION 17 Leveling the Appliance Adjusting the Legs Adjusting the Front Legs ••Attach level on top front opening of tub from side to side. ••Use a flat-blade screwdriver or a pliers to turn the front legs and adjust the front of the tub. ••Attach level on front side of tub. ••Turn the front legs clockwise to raise the front of the tub and counter-clockwise to lower it. ••The adjustments work identically for both front legs.
18 INSTALLATION Securing Dishwasher to Countertop Connecting Drain Hose For countertops made of wood or other material that will not be damaged by drilling, use Method 1. For countertops made of granite, marble, or other materials that could be damaged by drilling, use Method 2. NOTE ••Cover the filter hole with towels to prevent screws from falling down into the pump. ••Use a magnetic screwdriver.
INSTALLATION 19 NOTE ••If the knockout plug has not been removed, the dishwasher will not be able to drain properly. 1 1 Remove the knockout plug with a hammer and screwdriver. 2 Connect end of the drain hose to the air gap with hose clamp provided. This avoids water being siphoned from the tub. Remove the knockout plug with a hammer and screwdriver. Air gap Knockout plug Rubber hose connector 2 Attach the drain hose to disposal with the hose clamp provided.
20 INSTALLATION Connecting Water Supply 1 Before connecting, turn off the water supply. 2 Slide the flexible stainless-steel water line or copper tube into the elbow. 3 Tighten the compression nut and make sure that the line is not kinked or pinched. Connecting Power NOTE ••The best location for the electrical conduit is on the right side of the back wall. Re-route the power cable before installation if the electrical conduit pipe is longer than 3" (76 mm) and is centered on the back wall.
INSTALLATION 21 Final Check 1 Turn on electrical power. 3 Make sure the door opens and closes smoothly. If necessary, level the dishwasher again. If the door will not close, make sure the rack is level and all packaging materials have been removed. Possible Cause and Solution Drain hose kinked or pinched. OE Error Feed the drainage and supply hoses through the hole under the sink. Then gradually slide the dishwasher into the cabinet while pulling on the hoses under the sink to take up any slack.
