ENGLISH OWNER’S MANUAL MONITOR TV Please read this manual carefully before operating your set and retain it for future reference. MONITOR TV MODELS M2262D M2362D M2762D M2262DP M2362DP M2762DP www.lg.
PREPARATION FRONT PANEL CONTROLS ■ This is a simplified representation of the front panel. The image shown may be somewhat different from your set. Headphone Jack Power Indicator illuminates blue when the set is switched on. Note:You can adjust Power indicator in the OPTION menu.
PREPARATION BACK PANEL INFORMATION ■ This is a simplified representation of the back panel. The image shown may be somewhat different from your set. 1 2 3 4 6 5 COMPONENT IN RS-232C IN (CONTROL & SERVICE) 2 RS-232C IN (CONTROL & SERVICE) PORT Serial port used for external control or service. R 10 AUDIO R DVI-D Input Digital PC input. L (MONO) L HDMI Input High definition inputs. These two inputs accept TV Video, not PC Video.
PREPARATION STAND INSTALLATION ■ The image shown may be somewhat different from your set. 1 Carefully place the product screen side down on a cushioned surface that will protect product and screen from damage. 2 Insert the S t a n d B a s e into the product. Stand Base OPEN OPEN OPEN Turn the S t a n d B a s e L o c k through 90° to fix the stand base to the stand body.
PREPARATION STAND INSTALLATION ■ The image shown may be somewhat different from your set. 1 Carefully place the product screen side down on a cushioned surface that will protect product and screen from damage. 2 Insert the S t a n d B a s e into the product. Stand Base 3 Use a C o i n on the bottom of the stand base and turn the screw clockwise to tighten.
PREPARATION DETACHING STAND ■ The image shown may be somewhat different from your set. 1 Place the set screen side down on a cushion or soft cloth. 2 Detach the monitor to the S t a n d B a s e by turning the screw to the left. Stand Base 4 Pushing L a t c h inside, Take the stand base from stand body. OPEN OPEN OPEN OPEN OPEN Turn the S t a n d B a s e L o c k through 90° to separate the stand base from the stand body.
PREPARATION DETACHING STAND ■ The image shown may be somewhat different from your set. 1 Place the set screen side down on a cushion or soft cloth. 2 Detach the stand base from the set by turning the screw to the left with a coin. Coin 3 Pull the stand base.
PREPARATION DETACHING STAND BODY ■ The image shown may be somewhat different from your set. ■ Remove the Stand Body in the same way as the following when using it as a Wall Hook. 1. Remove the screw 2 point. 2. Pull the stand body. 1. Remove the screw 4 point. 2. Pull the stand body.
PREPARATION WALL MOUNT: HORIZONTAL INSTALLATION For proper ventilation, allow a clearance of 10 cm on each side and from the wall. Follow the instructions included with the wall mount. 10 cm 10 cm 10 cm 10 cm 10 cm DESKTOP PEDESTAL INSTALLATION For proper ventilation, allow a clearance of 10 cm on each side and from the wall.
PREPARATION SWIVEL STAND(Only M2762D/M2762DP) ■ The image shown may be somewhat different from your set. After installing the set, you can adjust the set manually to the left or right direction by 179 degrees to suit your viewing position. 179° 179° POSITIONING YOUR DISPLAY ■ The image shown may be somewhat different from your set. Adjust the position of the panel in various ways for maximum comfort.
PREPARATION LOCATION Position your set so that no bright light or sunlight falls directly onto the screen. Care should be taken not to expose the set to any unnecessary vibration, moisture, dust or heat. Also, ensure that the set is placed in a position to allow a free flow of air. Do not cover the ventilation openings on the back cover. If you intend to mount the set to a wall, attach the wall mounting interface (optional parts) to the back of the set.
PREPARATION SECURING THE SET TO THE WALL TO PREVENT FALLING WHEN THE SET IS USED ON A STAND(Only M2762D/M2762DP) ■ Image shown may differ from your set. We recommend that you set up the set close to a wall so it cannot fall over if pushed backwards. Additionally, we recommend that the set be attached to a wall so it cannot be pulled in a forward direction, potentially causing injury or damaging the product. Caution: Please make sure that children don’t climb on or hang from the set.
PREPARATION ATTACHING THE TV TO A DESK (Only M2762D/M2762DP) ■ The image shown may be somewhat different from your set. The TV must be attached to desk so it cannot be pulled in a forward/backward direction,potentially causing injury or damaging the product.Use only an attached screw. 1-Screw (provided as parts of the product) Stand Desk ! WARNING G 12 To prevent TV from falling over,the TV should be securely attached to the floor/wall per installation instructions.
PREPARATION KENSINGTON SECURITY SYSTEM - The product is equipped with a Kensington Security System connector on the back panel. Connect the Kensington Security System cable as shown below. - For detailed installation and use of the Kensington Security System, refer to the user’s guide provided with the Kensington Security System. For further information, contact h t t p : / / w w w . k e n s i n g t o n . c o m, the internet homepage of the Kensington company.
EXTERNAL EQUIPMENT SETUP ■ To prevent equipment damage, never plug in any power cords until you have finished connecting all equipment. ANTENNA CONNECTION For optimum picture quality, adjust antenna direction. ■ An antenna cable and converter are not supplied.
EXTERNAL EQUIPMENT SETUP ■ To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment. ■ The image shown may be somewhat different from your set. HD RECEIVER SETUP When connecting with a component cable 1 Connect the SET-TOP outputs to the C O M P O N E N T I N V I D E O sockets (Y PB PR) on the set. 2 Connect the audio cable from the SET-TOP to C O M P O N E N T I N A U D I O sockets of the set.
EXTERNAL EQUIPMENT SETUP When connecting with a HDMI 1 Connect the HDMI output of the digital set-top box to the H D M I I N jack on the set. 1 HDMI IN 2 1 When connecting with a HDMI to DVI cable 1 Connect the digital set-top box to H D M I I N jack on the set. 1 AUDIO IN (RGB/DVI) HDMI IN 2 2 Connect the audio output of the digital set-top box to the A U D I O I N ( R G B / D V I ) jack on the set. 3 Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.
EXTERNAL EQUIPMENT SETUP DVD SETUP When connecting with a component cable 1 Connect the video output sockets (Y PB PR) of the DVD to the C O M P O N E N T I N V I D E O sockets (Y PB PR) of the set. 2 Connect the audio cable from the DVD to C O M P O N E N T I N A U D I O sockets of the set. 3 Press the I N P U T button to select C o m p o n e n t. 4 Press the P L A Y button on the DVD. The DVD playback picture appears on the screen.
EXTERNAL EQUIPMENT SETUP When connecting S-Video 1 Connect the S-Video output of the DVD to the S-Video in put on the set. 2 Connect the audio output of the DVD to the AUDIO in put on the set. AV-IN 1 VIDEO S-VIDEO VIDEO S-VIDEO L (MONO) L 2 R AUDIO R When connecting HDMI cable 1 HDMI IN 1 Connect the HDMI output of the DVD to the H D M I I N jack on the set. 2 1 ! NOTE G HDMI supports video and audio. You do not need to connect a sperate audio cable.
EXTERNAL EQUIPMENT SETUP VCR SETUP To avoid picture noise (interference), leave an adequate distance between the VCR and the set. ■ If a user uses 4:3 picture format for a long time, an afterimage may remain on the sides of the screen for a short time. ■ When connecting with an antenna ANTENNA/ CABLE IN ANT OUT S-VIDEO ANT IN OUTPUT SWITCH VIDEO L R 1 Wall Jack 2 Antenna 1 Connect the RF out socket of the VCR to the antenna socket of the set.
EXTERNAL EQUIPMENT SETUP When connecting with a RCA cable 1 AV-IN Press the INPUT button to select AV. 1 L (MONO) L Press the PLAY button on the VCR. The VCR playback picture appears on the screen. R AUDIO R 3 S-VIDEO VIDEO S-VIDEO VIDEO 2 Connect the audio/video out sockets of the VCR to AUDIO/VIDEO in sockets of the set. ! NOTE G If you have a mono VCR, connect the audio cable from the VCR to the AUDIO L/MONO jack of the set.
EXTERNAL EQUIPMENT SETUP PC SETUP This product provides Plug and Play capability, meaning that the PC adjusts automatically to the set's settings. When connecting with a D-sub 15 pin cable 1 Connect the signal cable from the monitor output socket of the PERSONAL COMPUTER to the PC input socket of the set. 2 Connect the audio cable from the PC to the A U D I O I N ( R G B / D V I ) sockets of the set. 3 Press the INPUT button to select R G B. 4 Switch on the PC, and the PC screen appears on the set.
EXTERNAL EQUIPMENT SETUP When connecting with a DVI cable 1 Connect the DVI output of the PC to the D V I - D I N jack on the set. DVI-D IN (PC) 2 AUDIO IN (RGB/DVI) Connect the audio cable from the PC to the A U D I O I N ( R G B / D V I ) sockets of the set. 1 DVI OUTPUT 2 AUDIO ! NOTE G 22 Connect the signal input cabel and tighten the screws by turning them clockwise.
EXTERNAL EQUIPMENT SETUP BACK COVER FOR WIRE ARRANGEMENT Tie cables together with a cable tie as shown in the illustration.
EXTERNAL EQUIPMENT SETUP SUPPORTED DISPLAY RESOLUTION RGB/DVI[PC] Resolution Horizontal Frequency(kHz) Vertical Frequency(Hz) 720x400 31.468 31.469 37.500 37.879 46.875 48.363 60.123 67.500 63.981 79.976 64.674 65.290 75.000 66.
EXTERNAL EQUIPMENT SETUP INITIAL SETTING This Function guides the user to easily set the essential items for viewing the TV for the first time when purchasing the TV. If will be displayed on the screen when turning the TV on for the first time. It can also be activated from the user menus. ■ ■ H o m e”. We recommend setting the TV to “H H o m e” mode for the best picture in your Default selection is “H home environment.
WATCHING TV / CHANNEL CONTROL REMOTE CONTROL KEY FUNCTIONS When using the remote control, aim it at the remote control sensor on the set. POWER Turns your set on or off. POWER TV/PC PICTURE INPUT SOUND SAP RATIO 1 2 3 4 5 6 7 8 9 - 0 FLASHBK TV/PC Selects TV or PC mode. Switches the set on. INPUT External input modes rotate in regular sequence PICTURE Toggles through the factory preset picture settings depending on the viewing environment. SOUND Toggles through preset sound settings.
WATCHING TV / CHANNEL CONTROL TURNING ON THE TV 1 First, connect the power cord correctly. POWER 2 Turn on the power by pressing the power button on the product. TV/PC PICTURE 3 Press the TV/PC button on the remote control. 4 Set the channel by using the CH + / - buttons or number buttons on the remote control.
WATCHING TV / CHANNEL CONTROL CHANNEL SELECTION 1 Press the C H + or - or NUMBER buttons to select a programme number. POWER TV/PC PICTURE VOLUME ADJUSTMENT 1 Press the VOL + or - button to adjust the volume. INPUT SOUND SAP RATIO 1 2 3 4 5 6 7 8 9 - 0 FLASHBK If you want to switch the sound off, press the MUTE button. FAV LIGHTING You can cancel this function by pressing the MUTE, VOL + or - . VOL CH MUTE Q.
WATCHING TV / CHANNEL CONTROL QUICK MENU / FAVORITE CHANNEL SETUP Your set’s OSD (On Screen Display) may differ slightly from what is shown in this manual. Q.Menu (Quick Menu) is a menu of features which users might use frequently. ■ ■ ■ ■ ■ ■ ■ ■ A s p e c t R a t i o: Selects your desired picture format. B a c k l i g h t: Adjust the brightness of the LCD panel to control the brightness of the screen and lower power consumption. P i c t u r e M o d e: Toggles through picture settings.
WATCHING TV / CHANNEL CONTROL ON SCREEN MENUS SELECTION AND ADJUSTMENT Your set's OSD (On Screen Display) may differ slightly from what is shown in this manual.
WATCHING TV / CHANNEL CONTROL AUTO CHANNEL TUNING Use this to automatically find and store all available channels. When you start auto programming in digital mode, all previously stored service information will be deleted. CHANNEL Move Enter Auto tuning tuning Auto Manual tuning Channel Edit CHANNEL Move Enter Auto tuning tuning Auto Manual tuning Channel Edit Press ‘Yes’ button to begin auto tuning. Yes No 1 MENU Select CHANNEL.
WATCHING TV / CHANNEL CONTROL MANUAL TUNING When selecting DTV or TV or CADTV or CATV input signal, you can view the on-screen signal strength monitor to see the quality of the signal being received. CHANNEL Move CHANNEL Enter Auto tuning Manual Manual tuning tuning Channel Edit Auto tuning Manual Manual tuning tuning Channel Edit Move Enter DTV F G Select channel type and RF-channel number. Channel 2 DTV 2-1 Bad Normal Good Add Close 1 MENU Select CHANNEL. ENTER Select Manual Tuning.
WATCHING TV / CHANNEL CONTROL CHANNEL EDIT A custom list can be created by toggling each channel on or off with the ENTER button. The channels in the Custom List are displayed in black and the channels deleted from the Custom List are displayed in gray. Once a channel is highlighted you can add or delete the channel by pressing the enter button. CHANNEL Move Enter Auto tuning Manual tuning Channel Channel Edit Edit Move CH Move Page RETURN Previous Q.MENU Add/Delete 1 MENU Select CHANNEL.
PICTURE CONTROL PICTURE SIZE (ASPECT RATIO) CONTROL This feature lets you choose the way an analog picture with a 4:3 aspect ratio is displayed on your set. ■ RGB-PC input source use 4:3 or 16:9 aspect ratio. ! NOTE G If a fixed image is displayed on the screen for a long time, the image could become imprinted on the screen and remain visible. This phenomenon is common to all manufacturers and is not covered by warranty.
PICTURE CONTROL Set by program Zoom 1 Selects the proper picture proportion to match the source’s image. Choose Zoom 1 when you want to view the picture without any alteration. However, the top and bottom portions of the picture will be cropped. 4:3 Choose 4:3 when you want to view a picture with an original 4:3 aspect ratio. Zoom 2 Choose Zoom 2 when you want the picture to be altered, both vertically extended and cropped. The picture taking a halfway trade off between alteration and screen coverage.
PICTURE CONTROL PRESET PICTURE SETTINGS Picture Mode-Preset There are factory presets for picture settings available in the user menus. You can use a preset, change each setting manually. Q.Menu Aspect Ratio 16:9 3 Backlight F Picture Mode G Vivid Standard Cinema Standard Sound Mode Off Caption CH Vivid Multi Audio English Sleep Timer Off Del/Add/Fav Add Game Sport Close 1PICTURE Select V i v i d, S t a n d a r d, C i n e m a, S p o r t, or G a m e.
PICTURE CONTROL AUTO BRIGHT When ON is selected, this function adjusts the screen brightness automatically, depending on the surrounding environment, to provide optimal viewing conditions. When OFF is selected, this function is turned off.
PICTURE CONTROL PRESET PICTURE SETTINGS Picture Mode-Preset PICTURE Move Aspect Ratio Auto Bright Picture PictureMode Mode PICTURE Aspect Ratio Auto Bright Picture Picture Mode Mode Move : 16:9 : Off :: Vivid Vivid • Backlight • Contrast • Brightness • Sharpness • Color Enter : 16:9 : Off : :Vivid Standrad • Backlight • Contrast • Brightness • Sharpness • Color 80 100 50 70 50 Enter Vivid Standard Standrad Cinema Sport Game E 100 100 50 70 70 PICTURE Move Aspect Ratio Auto Bri
PICTURE CONTROL Auto Color Tone Control (Warm/Medium/Cool) Choose one of three automatic color adjustments. Set to warm to enhance warm colors such as red, or set to cool to see less intense colors with more blue.
PICTURE CONTROL Auto Color Tone Control (6500K/9300K/sRGB)(RGB,DVI mode only) Choose one of two automatic color adjustments.
PICTURE CONTROL MANUAL PICTURE ADJUSTMENT Picture Mode-User option PICTURE Aspect Ratio Auto Bright Picture Picture Mode Mode Move : 16:9 : Off :: Vivid Vivid(User) • Backlight • Contrast • Brightness • Sharpness • Color PICTURE Enter Move Aspect Ratio : 16:9 Auto Bright : Off Picture : Vivid (User) Picture Mode Mode : Standard • Backlight • Contrast • Brightness • Sharpness • Color Enter Vivid Standard Standard(User) 80 Cinema 100 Sport 50 Game 70 G 50 R E 100 100 50 70 70 PICTUR
PICTURE CONTROL PICTURE IMPROVEMENT TECHNOLOGY Fresh Contrast Optimizes the contrast automatically according to the brightness of the reflection. Fresh Color Adjusts the color of the reflection automatically to reproduce natural colors as close as possible. Noise Reduction Removes interference up to the point where it does not damage the original picture. Gamma High gamma values display whitish images and low gamma values display high contrast images.
PICTURE CONTROL ADVANCED - BLACK (DARKNESS) LEVEL When you view a film, this function adjusts the set to the best picture quality.
PICTURE CONTROL ADVANCED - FILM MODE To set the product up for the best picture quality for viewing films. This feature operates only in TV, AV and Component 480i/1080i , HDMI 1080i mode.
PICTURE CONTROL PICTURE RESET Settings of the selected picture modes return to the default factory settings. PICTURE Move PICTURE Enter D • Backlight 100 • Contrast 100 • Brightness 50 • Sharpness 70 • Color 70 • Tint 0 • Advanced Control • Reset Move Enter D R G • Backlight 100 • Contrast 100 • Brightness 50 • Sharpnessi Resetting 70 video configuration... • Color 70 R G • Tint 0 • Advanced Control • Reset 1 MENU Select PICTURE. ENTER Select Picture Reset.
PICTURE CONTROL SCREEN SETUP FOR PC MODE Selecting Resolution To view a normal picture, set the resolution to match what the PC is using. This function works in the following resolution in RGB[PC] mode. SCREEN Resolution Move G Auto Config. Position MENU Prev.
PICTURE CONTROL Auto Configure (RGB [PC] mode only) Automatically adjusts picture position and minimizes image instability. After adjustment, if the image is still not correct, your set is functioning properly but needs further adjustment. Auto configure This function is for automatic adjustment of the screen position, clock, and phase The displayed image will be unstable for a few seconds while the auto configuration is in progress. 1. Using OSD PICTURE Move SCREEN Enter Move MENU Prev.
PICTURE CONTROL Adjustment for screen Position, Size, Phase If the picture is not clear after auto adjustment and especially if characters are still shaky, adjust the picture phase manually. This function works in the following mode: RGB[PC]. PICTURE Move SCREEN Enter MENU Prev. Move D • Contrast : 100 • Brightness : 50 • Sharpness : 70 • Colour : 50 • Tint :0 • Advanced Control • Reset Screen(RGB-PC) Resolution Auto Config. D Position G F G E R G Size Phase Reset 1 MENU Select PICTURE.
PICTURE CONTROL Screen Reset Returns Position, Size and Phase to the default factory settings. This function works in the following mode: RGB[PC]. PICTURE Move SCREEN Enter Move MENU Prev. D • Contrast : 100 • Brightness : 50 • Sharpness : 70 • Colour : 50 • Tint :0 • Advanced Control • Reset Screen(RGB-PC) Resolution Auto Config. Initialize Settings. Position R G Size Phase Reset G 1 MENU Select PICTURE. ENTER Select SCREEN(RGB-PC). ENTER Select Reset. ENTER Select Yes.
SOUND CONTROL AUTO VOLUME LEVELER AVL automatically remains on the same volume level if you change programmes. AUDIO Move Auto Auto Volume Volume :: Off Off Balance Sound Mode : Standard • Treble • Bass • Reset TV Speaker 0 L 50 50 : On AUDIO Enter R Move Auto Auto Volume Volume :: Off Off Balance Sound Mode : Standard • Treble • Bass • Reset TV Speaker 0 Off Off L On 50 50 : On 1 MENU Select AUDIO. ENTER Select Auto Volume. ENTER Select On or Off.
SOUND CONTROL BALANCE You can adjust the sound balance of the speakers to preferred levels. AUDIO Auto Volume Balance Balance Sound Mode TV Speaker Move AUDIO Enter : Off 00 : Standard • Treble • Bass • Reset L R Auto Volume Balance Balance Sound Mode 50 50 : On TV Speaker Move Enter : Off 00 L0 • Balance : Standard • Treble • Bass • Reset 50 50 F L R R G Close : On 1 MENU Select AUDIO. ENTER Select Balance. ENTER Make desired adjustment.
SOUND CONTROL PRESET SOUND SETTINGS - SOUND MODE Sound Mode lets you enjoy the best sound without any special adjustment as the TV sets the appropriate sound options based on the program content. S t a n d a r d, M u s i c, C i n e m a, S p o r t, and G a m e are preset for optimum sound quality at the factory and are not adjustable. Q.
SOUND CONTROL PRESET SOUND SETTINGS - SOUND MODE You can select your preferred sound setting; Standard, Music, Cinema, Sport and Game and you can also adjust the frequencies of the equalizer. Standard, Music, Cinema, Sport and Game are preset for optimum sound quality at the factory.
SOUND CONTROL SOUND SETTING ADJUSTMENT - USER MODE Adjusting the audio equalizer. AUDIO Auto Volume Balance Sound Mode TV Speaker Move AUDIO Enter : Off 0 : Standard • Treble • Bass • Reset L R Auto Volume Balance Sound Mode 50 50 50 : On TV Speaker Move Enter : Off 0 : Standard • Treble • Bass • Reset 50 50 50 L R Treble 50 Bass 50 : On Close 1 MENU Select AUDIO. ENTER Select Sound Mode. ENTER Select Standard, Music, Cinema, Sport or Game. ENTER Select Treble or Bass.
SOUND CONTROL AUDIO RESET Settings of the selected Sound Mode return to the default factory settings. AUDIO Auto Volume Balance Sound Mode TV Speaker Move AUDIO Enter : Off 0 : Standard • Treble • Bass Reset •• Reset L R Auto Volume Balance Sound Mode 50 50 : On TV Speaker Move Enter : Off 0 : Standard • Treble • Bass •• Reset Reset : On L R 50 50 i Resetting audio configuration... 1 MENU Select AUDIO. ENTER Select Reset. 2 3 ENTER Initialize the adjusted value.
SOUND CONTROL TV SPEAKERS ON/ OFF SETUP You can tun of the speakers when using external audio system. AUDIO Auto Volume Balance Sound Mode TV TV Speaker Speaker 1 MENU Move AUDIO Enter : Off 0 : Standard • Treble • Bass • Reset L R Auto Volume Balance Sound Mode 50 50 :: On On TV TV Speaker Speaker Move Enter : Off 0 : Standard • Treble • Bass • Reset L R 50 50 :: On On Off On On Select AUDIO. 2 ENTER Select TV Speaker. ENTER Select On or Off.
SOUND CONTROL STEREO/SAP BROADCAST SETUP For Analog only: This TV can receive MTS stereo programs and any SAP (Secondary Audio Program) that accompanies the stereo program if the station transmits an additional sound signal. Mono sound is automatically used if the broadcast is only in Mono. Q.Menu Aspect Ratio 16:9 3 Backlight Picture Mode Vivid Sound Mode Standard Off Caption F Multi Audio CH English G Sleep Timer Off Del/Add/Fav Add Close Analog Mode Digital Mode 1 1 Q.
TIME SETTING CLOCK SETTING Auto Clock Setup The time is set automatically from a digital channel signal. The digital channel signal includes information for the current time provided by the broadcasting station. Set the clock manually if the current time is set incorrectly by the auto clock function.
TIME SETTING Manual Clock Setup If the current time setting is wrong, reset the clock manually. TIME Clock Clock Off Time On Time Sleep Timer Auto Sleep Move TIME Enter Clock Clock Off Time On Time Sleep Timer Auto Sleep : Off : Off : Off : On Move Enter F Manual Year : Off : Off : Off : On G 2008 Month 2 Date 21 Hour 2 AM Minute 10 Eastern Time Zone Daylight Saving Auto Close 1 MENU Select TIME. ENTER Select Clock. ENTER Select A u t o.
TIME SETTING AUTO ON/OFF TIMER SETTING The Off time function automatically switches the set to standby at a preset time. Two hours after the set is switched on by the on time function it will automatically switch back to standby mode unless a button has been pressed. The Off time function overrides the On timer function if both are set to the same time. The set must be in standby mode for the On timer to work.
TIME SETTING SLEEP TIMER SETTING The sleep timer automatically switches the set off after the preset time has elapsed. TIME Move TIME Enter Clock Off Time : Off On Time : Off Sleep Sleep Timer Timer :: Off Off Auto Sleep : On Clock Off Time : Off On Time : Off Sleep Sleep Timer Timer :: Off Off Auto Sleep : On Move Enter F Off G Close 1 MENU Select TIME. ENTER Select S l e e p T i m e r. ENTER Select O f f, 1 0, 2 0, 3 0, 6 0, 9 0, 1 2 0, 1 8 0 or 2 4 0 M i n . 2 3 4 ENTER Confirm it.
TIME SETTING AUTO SHUT-OFF SETTING If the set is switched on and there is no input signal, it will switch off automatically after 10 minutes. TIME Clock Off Time On Time Sleep Timer Auto Auto Sleep Sleep Move Enter : Off : Off : Off :: Off On TIME Clock Off Time On Time Sleep Timer Auto Auto Sleep Sleep Move : Off : Off : Off :: Off On Enter On Off Off TV will be automatically turned off, in case of No Signal for 10 minutes. 1 MENU Select TIME. ENTER Select Auto Sleep. ENTER Select Off or On.
OPTION SETTING ON-SCREEN MENUS LANGUAGE SELECTION The menus can be shown on the screen in the selected language. OPTION Move Language Language Input Label Key Lock Caption Set ID Power Indicator DDC-CI Enter English :: English : Off : Off :1 : On : On E OPTION Move Language Language Input Label Key Lock Caption Set ID Power Indicator DDC-CI English :: English Enter Menu Audio : Off : Off :1 : On : On F English G English Close E 1 MENU Select OPTION. ENTER Select Language.
OPTION SETTING INPUT LABEL Selects a label for each input source. OPTION Move Language Input Label Input Label Key Lock Caption Set ID Power Indicator DDC-CI OPTION Enter : English Move Language Input Label Input Label Key Lock Caption Set ID Power Indicator DDC-CI : Off : Off :1 : On : On E Enter : English AV : Off : Off :1 : On : On Component RGB-PC HDMI 1 HDMI 2 DVI E Close 1 MENU Select OPTION. 2 Select Input Label. ENTER 3 ENTER Select the source. 4 Select the label.
OPTION SETTING KEY LOCK The set can be configured so that the remote control is required to control it. This feature can be used to prevent unauthorized viewing. OPTION Move Language Input Label Key Lock Key Lock Caption Set ID Power Indicator DDC-CI Enter : English :: Off : Off :1 : On : On E 1 Select OPTION. MENU 2 ENTER Select Key Lock. ENTER Select On or Off.
OPTION SETTING Analog Broadcasting System Captions Caption must be provided to help people with hearing loss watch TV. Select a caption mode for displaying captioning information if provided on a program. Analog caption displays information at any position on the screen and is usually the program's dialog. Caption/Text, if provided by the broadcaster, would be available for both digital and analog channels on the Antenna/Cable.
OPTION SETTING Digital Broadcasting System Captions Choose the language you want the DTV/CADTV Captions to appear in. Other Languages can be chosen for digital sources only if they are included on the program. This function in only available when Caption Mode is set On.
OPTION SETTING Caption Option Customize the DTV/CADTV captions that appear on your screen. This function in only available when Caption Mode is set On. OPTION Move Language Input Label Key Lock Caption Caption Set ID Power Indicator DDC-CI Enter : English : Off :: Off CC1 :1 : On : On F OPTION Move Language Input Label Key Lock Caption Caption Set ID Power Indicator DDC-CI Enter : English : Off :: Off CC1 F :1 Mode : On : On On G CC1 Digital Option Close E E 1 MENU Select O P T I O N.
OPTION SETTING POWER INDICTOR It helps you control LED when power is turned on. OPTION Move Language Input Label Key Lock Caption Set ID Power Indicator Power Indicator DDC-CI Enter : English : Off : Off :1 :: On : On E OPTION Move Language Input Label Key Lock Caption Set ID Power Indicator Power Indicator DDC-CI Enter : English : Off : Off :1 :: On : On Off On On E 1 MENU Select OPTION. ENTER Select Power Indicator. ENTER Select On or Off.
OPTION SETTING DDC CI(Only RGB, DVI mode) DDC/CI (Display Data Channel Command Interface) is a communication protocol for communications between a PC and Monitor. DDC/CI makes it possible to adjust and setup detailed functions on the PC instead of the Monitor. On allows adjustments on the PC. Off ignores the communications of DDC/CI data.
PARENTAL CONTROL / RATINGS LOCK SYSTEM Enter the password, press ‘0’, ‘0’, ‘0’, ‘0’ on the remote control handset. LOCK Move Enter Lock System : Off Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General Downloadable Rating Input Block LOCK Move Enter Off : Off Off On Lock System Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General Downloadable Rating Input Block 1 MENU Select LOCK. ENTER Select Lock System. ENTER Select On or Off.
PARENTAL CONTROL / RATINGS SET PASSWORD LOCK Move LOCK Enter Lock System : Off Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General Downloadable Rating Input Block Lock System : Off Set Set Password Password Block Channel Movie Rating TV Rating-Children TV Rating-General Downloadable Rating Input Block 1 2 ENTER 1 2 3 4 5 6 7 8 9 Enter New * * * * Confirm * * * * Close • If you forget your password, press ‘7’, ‘7’, ‘7’, ‘7’ Select LOCK.
PARENTAL CONTROL / RATINGS BLOCK CHANNEL Blocks any programs that you do not want to watch or that you do not want your children to watch. This function is available in Lock System “On”. LOCK Move Enter Lock System : Off Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General Downloadable Rating Input Block Move CH Move Page RETURN Previous Q.MENU Block/Unblock 1 MENU Select LOCK. 2 ENTER Select Block Channel. 3 Q.MENU Select a channel to block or unblock it. 4 Q.
PARENTAL CONTROL / RATINGS MOVIE RATING Blocks movies according to the movie ratings limits specified, so children cannot view certain movies. You can set the ratings limit by blocking out all the movies with the ratings above a specified level. Keep in mind that the movie ratings limit only applies to movies shown on TV, not TV programs, such as soap operas.
PARENTAL CONTROL / RATINGS TV RATING-CHILDREN Prevents children from watching certain children's TV programs, according to the ratings limit set. The children rating does not apply to other TV programs. Unless you block certain TV programs intended for mature audiences in the TV Rating - sub menu, your children can view those programs.
PARENTAL CONTROL / RATINGS TV RATING-GENERAL Based on the ratings, blocks certain TV programs that you and your family do not want to view. LOCK Move LOCK Enter Lock System : Off Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General Downloadable Rating Input Block Move Lock System : Off Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General Downloadable Rating Input Block Enter Age Dialogue Language Sex Violence Close 1 MENU Select LOCK.
PARENTAL CONTROL / RATINGS DOWNLOADABLE RATING This function may become available in the future and will be available only for digital channel signal. This function operates only when TV has received Region5 Rating data.
PARENTAL CONTROL / RATINGS INPUT BLOCK Enables you to block an input. LOCK Move LOCK Enter Lock System : Off Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General Downloadable Rating Input Input Block Block Move Lock System : Off Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General Downloadable Rating Input Input Block Block Enter AV F Off Component Off RGB-PC Off HDMI1 Off HDMI2 Off DVI Off G Close 1 MENU Select LOCK.
APPENDIX TROUBLESHOOTING The operation does not work normally. Check to see if there is any object between the product and the remote control causing obstruction. Ensure you are pointing the remote control directly at the set. A Ensure that the batteries are installed with correct polarity (+ to +, - to -). A Ensure that the correct remote operating mode is set: TV, VCR, etc. A Install new batteries. A The remote control doesn’t work Is the sleep timer set? A Check the power control settings.
APPENDIX No Audio. A Picture OK but no sound A A A No output from one of the speakers Unusual sound from inside the product Press the VOL + or - button. Sound muted? Press MUTE button. Try another channel. The problem may be with the broadcast. Are the audio cables installed properly? A Adjust B a l a n c e in menu option. A A change in ambient humidity or temperature may result in an unusual noise when the product is turned on or off and does not indicate a problem with the product.
APPENDIX ‘Unknown Product’ message appears when the product is connected. A Install the product driver, which is provided with the product, or download it from the web site. (http://www.lg.com) A The Video card in the PC is not properly communicating with the monitor. Try installing the latest drivers for the video card. Did you install the driver? After-image appears on the screen. After-image appears when the product is turned off.
APPENDIX MAINTENANCE Careful and regular cleaning can extend the amount of time you can enjoy your new set. Caution: Be sure to turn the power off and unplug the power cord before you begin any cleaning. Cleaning the Screen 1 To keep the dust off your screen for a while, wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dishwashing detergent. Wring the cloth until it’s almost dry, and then use it to wipe the screen.
APPENDIX PRODUCT SPECIFICATIONS LCD Panel Video Signal Screen Type 546.86 mm Wide (21.53 inch) TFT (Thin Film Transistor) LCD (Liquid Crystal Display) Panel Visible diagonal size : 546.86 mm Pixel Pitch 0.248 mm (H) x 0.248 mm (V) Max.
APPENDIX PRODUCT SPECIFICATIONS LCD Panel Video Signal Screen Type 584.2 mm Wide (23 inch) TFT (Thin Film Transistor) LCD (Liquid Crystal Display) Panel Visible diagonal size : 584.2 mm Pixel Pitch 0.265 mm (H) x 0.265 mm (V) Max.
APPENDIX PRODUCT SPECIFICATIONS LCD Panel Video Signal Screen Type 686 mm Wide (27 inch) TFT (Thin Film Transistor) LCD (Liquid Crystal Display) Panel Visible diagonal size : 686 mm Pixel Pitch 0.3114 mm (H) x 0.3114 mm (V) Max.
APPENDIX IR CODES 1. How to Connect A Connect your wired remote control to the Remote Control port on the set. 2. Remote Control IR Codes A Output waveform Single pulse, modulated with 37.
APPENDIX EXTERNAL CONTROL DEVICE SETUP RS-232C Setup Connect the RS-232C (serial port) input jack to an external control device (such as a computer or an A/V control system) to control the product’s functions externally. Connect the serial port of the control device to the RS232C jack on the product back panel. Note: RS-232C on this unit is intended to be used with third party RS-232C control hardware and software.
APPENDIX Set ID Use this function to specify a set ID number. p . 91 Refer to ‘Real Data Mapping’. OPTION Move Language Input Label Key Lock Caption Set ID Set ID Power Indicator DDC-CI Enter : English : Off : Off :: 1 1 : On : On OPTION Move Language Input Label Key Lock Caption Set ID Set ID Power Indicator DDC-CI E Enter : English : Off : Off F :: 1 1 : On : On 1 G Close E 1 MENU Select OPTION. 2 ENTER Select Set ID. ENTER adjust Set ID to choose the desired set ID number.
APPENDIX Command Reference List COMMAND1 COMMAND2 01. Power 02. Input Select 03. Aspect Ratio 04. Screen Mute 05. Volume Mute 06. Volume Control 07. Contrast 08. Brightness 09. Color 10. Tint 11. Sharpness 12. OSD Select 13. Remote Control Lock Mode k x k k k k k k k k k k a b c d e f g h i j k l 00 to 01 (G p.90) (G p.90) 00 to 01 00 to 01 00 to 64 00 to 64 00 to 64 00 to 64 00 to 64 00 to 64 00 to 01 k m 00 to 01 COMMAND1 COMMAND2 19.
APPENDIX 01. Power (Command: k a) 06. Volume Control (Command: k f) To control Power On/Off of the set. To adjust volume. Transmission [k][a][ ][Set ID][ ][Data][Cr] You can also adjust volume with the volume buttons on remote control.
APPENDIX 12. OSD Select (Command: k l) 18. Auto Configuration (Command: j u) To select OSD (On Screen Display) on/off. To adjust picture position and minimize image shaking automatically. Auto configuration only works in RGB-PC mode. Transmission [k][l][ ][Set ID][ ][Data][Cr] Data 00: OSD off Data 01: OSD on Transmission [ j ][u][ ][Set ID][ ][Data][Cr] Acknowledgement [l][ ][Set ID][ ][OK/NG][Data][x] Data 01: To set Acknowledgement [u][ ][Set ID][ ][OK/NG][Data][x] 13.
APPENDIX Data5: 7 Main/Sub Picture 6 Two/One Part Channel 5 Using Physical Channel 4 3 2 1 0 Step NTSC Air NTSC Cable ATSC Air ATSC Cable_std ATSC Cable_hrc ATSC Cable_irc ATSC cable_auto Reserved ... Reserved Reserved 0 Main 0 Two 0 Use x 0 0 0 0 1 Sub 1 One 1 No Use x 0 0 0 1 x 0 0 1 0 x 0 0 1 1 x 0 1 0 0 x 0 1 0 1 x 0 1 1 0 x 0 1 1 1 The table above lists the binary code which must be converted to Hexadecimal before sending.
P/NO : 3840TRL098E (0801-REV00)
Make sure to read the Safety Precautions before using the product. Keep the Owner’s Manual(CD) in an accessible place for future reference. The model and serial number of the SET is located on the back and one side of the SET. Record it below should you ever need service.