ENGLISH OWNER’S MANUAL LCD MONITOR Please read this manual carefully before operating your set and retain it for future reference. LCD MONITOR MODEL ME20CR www.lg.
Important Precautions This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing. On Safety Use only the power cord supplied with the unit.
Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord, and do not place the display where the power cord is subject to damage. Do not use this display near water such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. Displays are provided with ventilation openings in the cabinet to allow the release of heat generated during operation.
Important Precautions On Cleaning Unplug the display before cleaning the face of the display screen. Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display screen because over-spraying may cause electrical shock. When cleaning the product, unplug the power cord and scrub gently with a soft cloth to prevent scratching. Do not clean with a wet cloth or spray water or other liquids directly onto the product. An electric shock may occur.
Accessories !!! Thank you for selecting LGE products !!! Please make sure the following items are included with your monitor. If any items are missing, contact your reseller. Owner's Manual/Cards Power Cord DVI-D Signal Cable (This feature is not available in all countries.) Cable Holder NOTE This accessories may look different from those shown here. User must use shielded signal interface cables (DVI-D cable) with ferrite cores to maintain standard compliance for the product.
Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Connecting the stand base or Removing the stand base 1. Place the monitor with its front facing downward on a cushion or soft cloth. 2. Rotate the Stand Body as shown in figure 1 . 1 3. Align the hooks on the stand base with the matching slots in the base of the monitor. 4. Insert the hooks into slots.
Connecting the Display 5. Attach the monitor to the Stand Base by turning the screw to the right. Screw : Turn the screw by using the screw handle. 6. Lift and turn the monitor to face towards the front after the connection is made to the female part of the cable you're attaching. 7. Take the screw out by turning to the left to separate the monitor and Stand Base. IMPORTANT This illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture.
Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices are turned off. Positioning your display 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -5˚ to 20˚ Swivel : 350˚ Height Range : maximun 100.0 mm (3.94 inch) 100.0 mm * Please be sure to remove the Locking pin to adjust the height. WARNING You do not need to replace the Locking pin after it is removed, to adjust its height.
Connecting the Display Using the Pivot function -The pivot function allows you to rotate the screen 90 degrees clockwise. 1. Lift the monitor to its highest height to utilize the Pivot function. 2. Landscape & Portrait : You can rotate the panel 90 o clockwise. Please be cautious and avoid contact between the monitor head and the Stand Base when rotating the screen to access the Pivot function. If the monitor head touches the Stand Base, then the Stand Base could crack.
Connecting the Display Connecting with the PC equipment 1. Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. and power cord of the signal cable. 2. Connect signal input cable 1 2 in order, then tighten the screw A Connect D-SUB Cable B Connect DVI-D Cable NOTE This is a simplified representation of the rear view. This rear view represents a general model; your display may differ from the view as shown.
Control Panel Functions Front Panel Controls MENU Button Use this button to enter or exit the On Screen Display. OSD LOCKED/UNLOCKED This function allows you to lock the current control settings, so that they cannot be inadvertently changed. Press and hold the MENU button for several seconds. The message "OSD LOCKED" should appear. You can unlock the OSD controls at any time by pushing the MENU button for several seconds. The message "OSD UNLOCKED" should appear. Button Use this button to enter menu.
Control Panel Functions EXIT Button Exit the OSD(ON Screen Display). Power Button Use this button to turn the display on or off. Power Indicator From front view, the power indicator stays blue if the display is running properly (On Mode). If the display is in Sleep Mode (Energy Saving), this indicator color changes to amber.
On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make using the OSD.
On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus.
On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Press the MENU Button, then the main menu of the OSD appears. Menu Name Icons Submenus Exit Adjust (Decrease/Increase) Select another sub-menu Button Tip NOTE OSD (On Screen Display) menu languages on the monitor may differ from the manual.
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description BRIGHTNESS To adjust the brightness of the screen. CONTRAST To adjust the contrast of the screen. SHARPNESS To adjust the clearness of the screen. D-SUB/DVI-D input : Move to the upper menu : Decrease : Increase : Select another sub-menu NOTE If you want to exit, select and press "EXIT".
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description PRESET Mode COLOR TEMP Select either PRESET or USER to adjust the screen color. PRESET Select the screen color. • WARM : Slightly reddish white. • MEDIUM : Set the screen color to fit the sRGB standard color specification. • COOL : Slightly bluish white. USER RED Set your own red color levels. USER Mode GREEN Set your own green color levels. BLUE Set your own blue color levels. GAMMA Set your own gamma value.
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description D-SUB input HORIZONTAL To move image left and right. VERTICAL To move image up and down. CLOCK To minimize any vertical bars or stripes visible on the screen background. The horizontal screen size will also change. PHASE To adjust the focus of the display. This item allows you to remove any horizontal noise and clear or sharpen the image of characters.
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description D-SUB input DVI-D input LANGUAGE To choose the language in which the control names are displayed. POWER INDICATOR Use this function to set the power indicator on the front side of the monitor to ON or OFF. If you set OFF, it will be turned off. If you set ON at any time, the power indicator will automatically be turned on.
On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Press the Button, then the main menu of the OSD appears. Menu Name Submenus Exit Move / Select Button Tip NOTE OSD (On Screen Display) menu languages on the monitor may differ from the manual.
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description D-SUB/DVI-D input NORMAL Select this when you want to use the product in the most general using environment. MOVIE Select this when you are watching a video or movie. INTERNET Select this when you are working on the document (Word etc.
Troubleshooting Check the following before calling for service. No image appears Is the power cord of the display connected? Check and see if the power cord is connected properly to the power outlet. Is the power indicator light on? Press the Power button. Is the power on and the power indicator blue or green? Adjust the brightness and the contrast. Is the power indicator amber? If the display is in power saving mode, try moving the mouse or pressing any key on the keyboard to bring up the screen.
Troubleshooting Display image is incorrect ● Display Position is incorrect. • Select AUTO function to adjust your display image to the ideal setting. If the results are unsatisfactory, adjust the image position using the H position and V position icon in the on screen display. ● On the screen background, vertical bars or stripes are visible. • Select AUTO function to adjust your display image to the ideal setting.
Troubleshooting Display image is incorrect ● The screen color is mono or abnormal. • Check if the signal cable is properly connected and use a screwdriver to fasten if necessary. • Make sure the video card is properly inserted in the slot. • Set the color setting higher than 24 bits (true color) at Control Panel - Settings. ● The screen blinks. • Check if the screen is set to interlace mode and if yes, change it to the recommend resolution.
Specifications Display 51.054 cm (20.1 inch) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 51.054 cm 0.255 mm x 0.255 mm (Pixel Pitch) Sync Input Horizontal Freq. Vertical Freq. Input Form 28 kHz to 83 kHz (Automatic) 56 Hz to 60 Hz (Automatic) Separate Sync SOG (Sync On Green) , Digital Video Input Signal Input Input Form D-SUB Connector (Analogl) DVI-D Connector (Digital) RGB Analog (0.
Specifications Preset Modes (Resolution) Display Modes (Resolution) 1 2 3 4 5 6 7 *8 Horizontal Freq. (kHz) Vertical Freq. (Hz) 31.47 37.50 31.46 37.88 48.36 63.98 62.11 75.00 59.94 75.00 70.08 60.32 60.00 60.02 60.00 60.
Installing the Wall mount plate This monitor satisfies the specifications of the Wall mount plate or the interchange device. 1. After moving the product to face downward, make sure to place it on a soft cloth or a cushion to avoid surface damage. 2. Separate the head and the stand with the use of a screwdriver. 3. Install the Wall mount plate. Wall mount plate (Separate purchase) - Be sure to use screws and a wall mount that meet VESA standards.
Make sure to read the Safety Precautions before using the product. Keep the OWNER’S MANUALCD) in an accessible place for furture reference. The model and serial number of the SET is located on the back and one side of the SET. Record it below should you ever need service.
