ENGLISH ESPAÑOL INSTALLATION MANUAL ELECTRIC RANGE Please read these instructions thoroughly before installing and operating the range. LRE3025ST LRE3025SB LRE3025SW LRE3023ST LRE3023SB LRE3023SW Printed on 100% Recycled Paper www.lg.
TABLE OF CONTENTS TABLE OF CONTENTS 3 SAFETY 3 Before You Begin 3 Important Safety Instructions 5 Prepare to Install the Range 6 6 7 PREPARE TO INSTALL RANGE Installation Drawings ELECTRICAL CONNECTIONS 7 Electrical Connection Requirements 7 Connect Range Cord 8 3-Wire Connection With a Power Supply Cord 9 4-Wire Connection With a Power Supply Cord 9 3-Wire Connection: Conduit 10 4-Wire Connection: Conduit 11 INSTALL THE RANGE 11 Anti-Tip Device Installation 11 Final Install
SAFETY 3 Remove all tape and packing materials before using the range. Dispose of all plastic bags after unpacking the range. Never allow children to play with packing materials. You can download the installation and owner’s manual at: http://www.lg.com. IMPORTANT SAFETY INSTRUCTIONS Read and follow all instructions before using your oven to prevent the risk of fire, electric shock, personal injury, or damage when using the range. This guide does not cover all possible conditions that may occur.
SAFETY WARNING • Power supply cord and plug should not be modified. If it will not fit the outlet, have a proper outlet • Using an extension cord to connect the power is prohibited. The way to connect the power cord and plug directly is strongly recommended. • Electrical ground is required on this appliance. • You should make sure that the power cord is not pinched by the range or heavy objects. - Failure to do so can result in serious burns or electrical shock.
SAFETY PREPARE TO INSTALL THE RANGE TOOLS NEEDED Phillips Screwdriver Level Flat-blade Screwdriver Adjustable Wrench WARNING • Any person should not step or sit on the oven door. You should install the Anti-Tip Brackets supplied with the range. - The range could be tipped and injury might result from spilled hot liquid, food, or the range itself.
PREPARE TO INSTALL THE RANGE INSTALLATION DRAWINGS NOTE SAVE FOR THE USE OF THE LOCAL ELECTRICAL INSPECTOR CLEARANCES AND DIMENSIONS (Figure 1) To install range refer to the following Figure 1. For installation in CANADA, a Free-standing range is not to be installed closer than 15/32 (12mm) from any adjacent surface. CAUTION CAUTION • Make sure that the wall covering, countertop and cabinets around the range can withstand the heat (up to 194°F) generated by the range.
ELECTRICAL CONNECTIONS This appliance must be installed and grounded on a branch circuit by a qualified technician in accordance with the National Electrical code ANSI/NFPA NO. 70 latest edition. All wiring should conform to Local and NEC. This range requires a single-phase, 3 wire, A.C 120/208V or 120/240V 60Hz electrical system. Use only a 3-conductor or a 4-conductor UL-listed range cord with closed-loop terminals, open-end spade lugs with upturned ends or similar termination.
ELECTRICAL CONNECTIONS 3-WIRE CONNECTION WITH A POWER SUPPLY CORD WARNING • The middle (neutral or ground) wire of a 3 wire power cord or a 3 wire conduit has to be connected to the middle post of the main terminal block. The remaining two wires of the power cord or conduit have to be connected to the outside posts of the main terminal connection block. - Failure to do so can result in electrical shock, severe personal injury or death.
ELECTRICAL CONNECTIONS WARNING • Only a 4-conductor power-supply cord kit rated 120/240 volts, 50 amperes and marked for use with ranges with closed-loop connectors or open-end spade lugs with upturned ends shall be used. The middle (neutral) wire of the power cord or 4-wire conduit has to be connected to the middle post of the main terminal block. The other two wires of the power cord or conduit have to be connected to the outside posts of the main terminal connection block.
ELECTRICAL CONNECTIONS 4-WIRE CONNECTION: CONDUIT 1. Follow the instructions under “Install the conduit as follows” on page 8 to correctly install the strain relief. DO NOT install the conduit without a strain relief. 2. Loosen the 2 lower left and right screws from the terminal block. (Refer to Figure 12.) Remove the lower 2 center screws. 3. Remove ground strap and discard as shown in Figure 12. Do not discard any screws. 4.
INSTALL THE RANGE 11 ENGLISH Replace the access cover on the back of the range. To replace the wire cover, insert the two tabs into the openings located below the opening and tighten the three screws. Lower range Access cover Leg leveler Raise range Use a level to check your adjustments. Place the level diagonally on the oven rack, and check each direction for level. ANTI-TIP DEVICE INSTALLATION WARNING • Any person should not step or sit on the oven door.
MEMO
LG Customer Information Center For inquires or comments, visit www.lg.com or call 1-800-243-0000 USA, Consumer User 1-888-542-2623 CANADA Register your product Online! www.lg.