0 INSTALLATION INSTALLATION Installation Overview Please read the following installation instructions first after purchasing this product or transporting it to another location.
INSTALLATION 11 If you did not receive an anti-tip bracket with your purchase, call 1-800-243-0000 (1-888-542-2623 in CANADA) to receive one at no cost. Warning Warning Tip - Over Hazard •• The information in this manual should be followed exactly. Failure to do so may result in fire, electrical shock, property damage, personal injury, or death. A child or adult can tip the range and be killed. Verify the anti-tip bracket has been installed.
12 INSTALLATION Installing the Range Unpacking and Moving the Range CAUTION •• You should use two or more people to move and install the range. (Excessive Weight Hazard) Failure to do so can result in back or other injury. •• Do not use the door handles to push or pull the range during installation or when moving the range out for cleaning or service. Doing so can result in serious damage to the door of the range. Remove packing material, tape and any temporary labels from your range before using.
INSTALLATION 13 ENGLISH Dimensions and Clearances NOTE Save for the use of the local electrical inspector. 24" (60.9 cm) 3" (7.6 cm) Acceptable electrical outlet area Normal counter top depth Counter 36" (91.4 cm) top height A Cabinet opening Wall 24" (60.9 cm) 36" (91.4 cm) 3" (7.6 cm) 25" (63.5 cm) Center 15" (38 cm) Cabinet 11" (28 cm) 6" (15.2 cm) 29.8" (75.7 cm) 4" (10 cm) 9" (23 cm) 2.5" (6.3 cm) 5" (13 cm) 4" (10 cm) 6" (15.2 cm) 9" (23 cm) 2.5" (6.3 cm) A = 30" (76.2 cm) For U.
14 INSTALLATION Installing the Anti-tip Device Use a level to check your adjustments. Place the level diagonally on the oven rack, and check each direction for level. Warning Tip - Over Hazard First check direction . A child or adult can tip the range and be killed. Verify the anti-tip bracket has been installed. Ensure the anti-tip bracket is engaged when the range is moved. Do not operate the range without the anti-tip bracket in place.
INSTALLATION 15 •• Allow 2 to 3 ft (61.0 cm to 91.4 cm) of slack in the line so that the range can be moved if servicing is ever necessary. •• The power supply cord and plug should not be modified. If it will not fit the outlet, have a proper outlet Installed by a qualified electrician. Use the cord/conduit connection plate to install the power cord or conduit. Leave the connection plate as installed for power cord installations.
16 INSTALLATION 3-Wire Connection : Power Cord 4-Wire Connection : Power Cord Warning Warning •• The middle (neutral or ground) wire, which is white, of a 3-wire power cord or a 3-wire conduit has to be connected to the middle post of the main terminal block. The remaining two wires of the power cord or conduit have to be connected to the outside posts of the main terminal connection block. Failure to do so can result in electrical shock, severe personal injury or death.
INSTALLATION 17 4-Wire Connection: Conduit Install the conduit as follows: Remove the conduit connection plate from the rear of the oven and rotate it. The conduit hole (11/8") must be used. First, prepare the conduit wires as shown below. 3-Wire Conduit connection plate 4-Wire or Ground wire Second, install the conduit strain relief. For conduit installations, purchase a strain relief and insert it in the 11/8 in. (2.8 cm) conduit hole.
18 INSTALLATION Engaging the Anti-tip Device Installing the Rear Filler 1 •• Slide the range into position ensuring that the back leg slides under the anti-tip bracket. The range should sit flush against the back wall when properly installed. Using a screwdriver, remove the upper four screws that attach the rear bracket and loosen the lower two screws. 2 Place the rear filler on the rear bracket. •• Carefully attempt to tip the range forward to ensure that the anti-tip bracket is engaged properly.
OPERATION 19 ENGLISH OPERATION Control Panel Overview For Model : LSE4613 1 2 For Model : LSE4611 3 4 5 6 7 8 9 10 11 1 Smart DiagnosisTM Use during the Smart Diagnosis feature. 2 Smart Features The Tag On icon, for use with Smart Features. 3 Cook Time Press the button to set the desired amount of time for food to cook. The oven shuts off when the set cooking time runs out. 4 Start Time Press the button to set the delayed timed cook. The oven starts at the set time.
20 OPERATION Knob Positions After cleaning the oven knobs, make sure to replace each knob in the correct position. Failure to do so can result in improper operation of the burners.
OPERATION 21 Clock The clock must be set to the correct time of day in order for the automatic oven timing functions to work properly. 1 Set the oven mode knob to the Off position. 2 Press Clock. CLO shows in the display. 3 Press plus(+) or minus(-) to select the desired time. Plus(+) to increase the time and minus(-) to decrease the time. 4 Press Start to enter the time and start the clock.
22 OPERATION Timer On/Off Settings The Timer On/Off serves as an extra timer in the kitchen that beeps when the set time has run out. It does not start or stop cooking. Set the oven mode knob to the Off position. Press Setting key repeatedly to toggle through and change oven settings. The Timer On/Off feature can be used during any of the oven control functions.
OPERATION 23 Adjusting the Beeper Volume Your new oven may cook differently from the one it replaced. Use your new oven for a few weeks to become more familiar with it before changing the temperature settings. If after familiarizing yourself with the new oven, you still think that it is too hot or too cold, you can adjust the oven temperature yourself. 1 2 Set the oven mode knob to the Off position. 3 Press plus(+) or minus(-) to select the desired volume.
24 OPERATION Start Time (Delayed Timed Cook) Cook Time (Timed Cook) The automatic timer of the Delayed Timed Cook function turns the oven on and off at the time you select. This feature can be used with the Bake, Conv. Bake and Conv. Roast modes. Set the oven to cook for a specific length of time using the Timed Cook feature. This feature can only be used with the Bake, Conv. Bake and Conv. Roast modes.
OPERATION 25 Using the Cooktop Elements CAUTION Cooking Areas The cooking areas on your range are identified by permanent circles on the glass cooktop surface. For the most efficient cooking, fit the pan size to the element size. Pans should not extend more than 1/2 to 1-inch beyond the cooking area. When a control is turned on, a glow can be seen through the glass cooktop surface. The element cycles on and off to maintain the preset heat setting, even on Hi.
26 OPERATION Turning on the Dual element Turning on a Warming Zone element There is one dual element located in the left front position. Use the dual element as a dual or single element. 1 Push the Warming Zone element knob in. 2 Turn the knob in either direction to the desired setting. The control knob clicks when it is positioned at both Off and Hi. 1 Push in the appropriate knob. 2-A Turn the knob counterclockwise to use it as a Single element.
OPERATION 27 Choosing Cookware The size and type of cookware will influence the settings needed for the best cooking results. Be sure to follow the recommendations for using proper cookware. The cookware material determines how evenly and quickly heat is transferred from the surface element to the pan bottom. The most popular materials available are: Cookware should have flat bottoms that make good contact with the entire surface heating element.
28 OPERATION Using the Oven Using Oven Racks The racks have a turned-up back edge that prevents them from being pulled out of the oven cavity. Before Using the Oven NOTE •• Because the oven temperature cycles, an oven thermometer placed in the oven cavity may not show the same temperature that is set on the oven. •• It is normal for the convection fan to run while preheating during a regular bake cycle. •• The convection fan motor may run periodically during a regular bake cycle.
OPERATION 29 Tips for Convection Baking •• Baking time and temperature will vary depending on the characteristics, size, and shape of the baking pan used. •• Use Convection Bake for faster and more even multiple-rack cooking of pastries, cookies, muffins, biscuits, and breads of all kinds. •• Check for food doneness at the minimum recipe time. •• Bake cookies and biscuits on pans with no sides or very low sides to allow heated air to circulate around the food.
30 OPERATION Recommended Baking and Roasting Guide Baking results will be better if baking pans are centered in the oven as much as possible. If cooking on multiple racks, place the oven racks in the positions shown.
OPERATION 31 Smoking The Broil function uses intense heat from the upper heating element to cook food. Broiling works best for tender cuts of meat, fish, and thinly cut vegetables. Some models may feature a hybrid broiler consisting of an inner broiler that utilizes a carbon heating element which provides instantaneous heat, and a traditional outer broiling element. During normal broiler operation, it is normal for either element to cycle off intermittently.
32 OPERATION Recommended Broiling Guide The size, weight, thickness, starting temperature, and your preference of doneness will affect broiling times. This guide is based on meats at refrigerator temperature. For best results when broiling, use a pan designed for broiling. Food Quantity and/or Thickness Rack First Side Position (minutes) Second Side (minutes) Ground Beef Well done 1 lb. (4 patties) 1/2 to 3/4" thick 7 3-6 2-4 Beef Steaks Rare Medium Well done 1" thick 1 to 11/2 lbs.
OPERATION 33 Beef •• Steaks and chops should always be allowed to rest for five minutes before being cut into and eaten. This allows the heat to distribute evenly through the food and creates a more tender and juicy result. •• Pieces of meat that are thicker than two inches should be removed from the refrigerator 30 minutes prior to cooking. This will help them cook more quickly and evenly, and will produce less smoke when broiling.
34 OPERATION Pizza (For Model : LSE4611) Speed Roast The Pizza function is specially designed for cooking pizza. It heats from both the top and bottom to brown food more evenly. The Speed Roast feature is designed to quickly roast poultry. The combination of intense heat from the upper heating element and heated air from the back heating element result in crispier food and help to save cooking time. Speed roasting is especially good for medium sized poultry.
SMART FEATURES 35 3 Check Use Read and Write/P2P receive. Before Using Tag On The Tag On function allows you to conveniently use LG Smart Diagnosis™, set the cook mode and EasyClean® features, and communicate with your appliance using a smart phone. To use the Tag On function: 1 Download the LG Smart Oven application(Smart ThinQ) to a smart phone. 2 Turn on the NFC (Near Field Communication) function in the smart phone.
36 SMART FEATURES The NFC Antenna Position When using the Tag On function, position the smart phone so that the NFC antenna inside the back of the smart phone matches the position of the Tag On icon on the appliance. If the application is not able to show a target range, position the center back of the smart phone over the Tag On icon on the appliance. If the connection is not made immediately, move the smart phone very slightly in a widening circular motion until the application verifies the connection.