Specification

27 3/8”
(69.5 cm)
52 1/16”
(132.2 cm)
29 3/4”
(75.5 cm)
23 3/8”
(59.3 cm)
51 5/8”
(131.0 cm)
Junction Box
Location
47”
30”
23”
5”
28 1/2” Min.
28 5/8” Max.
51 13/16” Min.
51 15/16” Max.
Allow 1”
minimum for
overlap of oven
Allow 1”
minimum for
overlap of oven
23 1/2”
Minimum cutout location from floor 12”
27 3/8”
(69.5 cm)
52 1/16”
(132.2 cm)
29 3/4”
(75.5 cm)
23 3/8”
(59.3 cm)
51 5/8”
(131.0 cm)
Junction Box
Location
47”
30”
23”
5”
28 1/2” Min.
28 5/8” Max.
51 13/16” Min.
51 15/16” Max.
Allow 1”
minimum for
overlap of oven
Allow 1”
minimum for
overlap of oven
23 1/2”
Minimum cutout location from floor 12”
LWS 3063_
Built-In Wall Oven
DIMENSIONS / CLEARANCES / WEIGHT
Product Dimensions (in) (W x H x D) 29 3/4" x 52 1/16" x 24 3/8"
Cut-out (W x H x D) 28 1/2" x 51 15/16" x 23 1/2"
Overall Depth (in) - including handle 000"
Actual Depth with Door Open (in): 000"
Oven Interior Dimensions (in) (W x H x D) 000"" x 000"" x 000""
Carton Dimensions (in) (W x H x D) 33" x 57" x 30"
POWER RATINGS
Max. Amp load 32.5 A
Rating 7.8 kW
Requirements 120 / 240 VAC, 120 / 208 VAC
LG COOKING
HOME APPLIANCES
QUICK INSTALL & CLEARANCES
For full installation directions/clearances please refer to
the corresponding User Manual and Installation Guide.
IMPORTANT
© 2018 LG Electronics USA, Inc. All rights reserved. "LG Life’s Good" is a registered trademark of LG Corp. All other product and brand names are trademarks or registered trademarks of their respective owners. Design, features and specifications are subject to
change without notice. Non-metric weights and measurements are approximate. Some features may require Internet access. Content and services may vary by product and are subject to change without notice. 2/26/18
CUTOUT DIMENSIONS
The rst step of the installation is measure the current cutout dimensions and
compare them to the cutout dimensions shown below. Little or no cabinet work
may be necessary.
•
The cabinet base platform must be able to support 325lbs (147kg). If
the cabinet does not have a solid bottom, two braces or runners must be
installed level with the bottom of the cutout to support the weight of the
oven.
•
Make sure the base is level and the front of the cabinet is square. If the
cabinet base is not level, the oven glides will tend to slide out when
opening the door.
•
If marks, blemishes or the cutout opening are visible above the installed
oven, it may be necessary to add wood shims under the runners and front
trim until the marks or opening are covered.
•
If the cabinet does not have a front frame and the sides are less than 3/4”
(1.9 cm) thick, shim both sides equally to establish the cutout width.
•
The junction box must be ush with the rear wall of the cabinet as shown
below.
•
Allow at least a 23” clearance for the door depth when it is open.
•
Kitchen cabinets in contact with the oven must be heat resistant up to
194°F (90°C), and fronts of nearby units up to at least 158°F (70°C).
PRODUCT DIMENSIONS
•
Cabinet Width: 30” (762 mm)
•
Recommended
Minimum Cutout 12” (304.8 mm)
Location from Floor:
•
Cutout Depth: 23 1/2” Min. (596.9 mm)
•
Cutout Width: 28 1/2” Min. (723.9 mm)
28 5/8” Max. (727 mm)
•
Cutout Height: 51 13/16” Min. (1316 mm)
51 15/16” Max. (1319.2 mm)
IMPORTANT NOTES