User’s Guide M4212C M4712C Make sure to read the Safety Precautions before using the product. Keep the User's Guide(CD) in an accessible place for future reference. See the label attached on the product and give the information to your dealer when you ask for service.
Connecting the stand - Only on some models. 1. Take the parts for the stand out of the box and assemble them as shown in the picture. Parts Screws (6) First, check if the following parts are all present. Stand (1) cable management (1) 2. Place a soft cloth on the table and put the product with the screen facing downward. Connect the stand as shown in the following picture. 3. Use the screws to secure the stand on the rear side of the product as shown in the diagram.
Connecting the Speakers - Only on some models. Mount the product onto the speaker by using a screw as shown in the following connect the speaker cable. Type 1 When the speaker is installed. *Connect the input terminal with a proper color match.
Connecting the Speakers - Only on some models. Mount the product onto the speaker by using a screw as shown in the following connect the speaker cable. Type 2 After installing your speakers, use holders and cable ties to organize the speaker cables. Cable holder Remove the paper. * This feature is not available in all model. When the speaker is installed. Cable tie *Connect the input terminal with a proper color match. * This feature is not available in all model.
To install Portrait - Only M4212C "When installing Portrait, rotate it clockwise based on its front.
Using the Remote Control Name of the Remote Control Buttons • Power On/Off Button • Input Select Button (See next page) • AV Button • Sleep Button When watching AV, RGB PC,HDMI/DVI ,Component1, Component2 The product will be automatically turned off after a certain period of time. Press this button repetitively to select an appropriate time duration • PSM Button - Toggles through preset video settings.
Name and Function of the Parts * The product image in the user’s guide could be different from the actual image. Rear View AV IN/OUT Power Connector : Connect the power cord RS-232C Serial Ports RGB PC, HDMI/DVI Ports -HDMI Supports High Definition input and HDCP (High-bandwidth Digital Content Protection). Some devices require HDCP in order to display HD signals. PC Sound Jack : Connect the audio cable to the *LINE OUT jack of the PC sound card.
Connecting to External Devices When Connecting to your PC First of all, see if the computer, product and the peripherals are turned off. Then, connect the signal input cable. A When connecting with the D-Sub signal input cable. B When connecting with the HDMI to DVI signal input cable (not included). A PC Rear side of the product. PC/MAC MAC Macintosh Adapter (not included) Use the standard Macintosh adapter since an incompatible adapter is available in the market.
Connecting to External Devices 1 Turn on power by pressing the power button on the product. SOURCE AUTO/SET ON/OFF Power button 2 Turn on the PC. Select an input signal. Press the INPUT button on the remote control to select the input signal. INPUT SET Or, press the SOURCE button on the back of the product. SOURCE AUTO/SET A When connecting with a D-Sub signal input cable. • Select RGB PC : 15-pin D-Sub analog signal. B When connecting with a HDMI to DVI signal input cable.
Connecting to External Devices Daisy Chain Monitors Use this function when displaying ANALOG RGB inputs of a PC to the other product. • To use different products connected to each other Connect one end of the signal input cable(15-pin D-Sub Signal Cable) to the RGB OUT connector of product 1 and connect the other end to the RGB IN connector of other products.
Connecting to External Devices VESA FDMI wall Mounting This product supports a VESA FDMI compliant mounting interface. These mounts are purchaed separately and not available from LG. Refer to the instructions included with hte mount for more info. The Set is equipped with a kensington Securify System connector on the back panel. The cable and lock are available separate and are not sold by LG. For more info, visit http://www.kensington.com, the internet home page of the Kensington company.
Connecting to External Devices • AV Button • Input Select Button Toggles through video If you press the button once, the following Input Signal Window will appear. Select the signal type you want using the button. AV Component1 Component2 RGB PC HDMI/DVI 1 2 Input 3 4 5 6 7 8 9 AV Component1 Component2 RGB PC HDMI/DVI 0 * Inserting batteries into remote control. 1. Slide off the battery cover. 2. Insert the batteries with correct polarity (+/-). 3. Close the battery cover.
Connecting to External Devices Video Input Connect the video cable as shown in the below figure and then connect the power cord (See page 7) A When connecting with a BNC cable. B When connecting with a S-Video cable. • Connect to the S-Video input terminal to • Connect the input terminal with a watch high image quality movies. proper color match.
Connecting to External Devices Component Input (480i/480p/576i/576p/720p/1080i) Connect the video/audio cable as shown in the below figure and then, connect the power cord (See page 7). • Connect the input terminal with a proper color match. Product A Product M BNC Cable (not included) B Audio Cable (not included) M BNC Cable (not included) HDTV Receiver Audio Cable (not included) HDTV Receiver Note - Some devices may require HDCP in order to display HD signals.
Connecting to External Devices HDMI Input (480p/576p/720p/1080i/1080p) -HDMI Supports High Definition input and HDCP (High-bandwidth Digital Content Protection). Some devices require HDCP in order to display HD signals. Connect the video/audio cable as shown in the below figure and then connect the power cord (See page 7).
Connecting to External Devices Watching AV Outputs - When using AV input, you can connect the AV Out to other monitors. Video/TV BNC Cable (not included) Audio Cable (not included) IN Product OUT BNC Cable (not included) Audio Cable (not included) Video/TV Note • When multi-connecting in/out cascade format, no loss cables are recommended. We recommend that you should use cable distributor.
Cable management - Only on some models. 1. Arrange the cables in the center as shown in the following picture. 2. Fit the cable guide to the back to help manage the cables. cable management Removing the cable guide. Hold the Cable management with both hands and pull it downward. Warning • Do not use the cable management as a handle for the Monitor.
User Menus Screen Adjustment options SOURCE SOURCE Power Button AUTO/SET ON/OFF AUTO/SET ON/OFF • Press this button to turn on the power. Press this button again to turn it off. Power Indicator • This Indicator lights up blue when the display operates normally(on mode). If the display is in sleep (Energy Saving) mode, this indicator color changes to amber. MENU Button • Use this button to show/hide the OSD (On Screen Display) menu screen.
User Menus Screen Adjustment options AUTO/SET Button [For PC Analog signal] [When XGA Mode is active and 1360 X768 is selected] SOURCE Button IR Receiver SOURCE AUTO/SET - Toggles between inputs Input AV Component 1 Component 2 RGB PC HDMI/DVI AV Component1 Component2 RGB PC HDMI/DVI Composite Video, Separate Video HDTV, DVD HDTV, DVD 15-pin D-Sub analog signal Digital signal • This is where the unit receives signals from the remote control.
User Menus OSD Menu Icon Function Description Adjusts screen brightness, contrast and color that you prefer. Picture Adjusts the audio options. Audio Adjusts the timer options. Time Adjusts the screen status according to the circumstances. Option Adjust Set ID and check Serial No. and SW version. Information Note OSD(On Screen Display) The OSD function enables you to adjust the screen status conveniently since it provides graphical presentation.
User Menus How to adjust the OSD (On Screen Display) screen Pops up the menu screen Move where you want to adjust Select a menu icon Move where you want to adjust Select a menu icon Adjust the status Save adjustment Exit from the menu screen. • Use the remote control to adjust the OSD screen. 1 Press the MENU Button, then the main menu of the OSD appears. 2 To access a control, use the 3 When the icon you want becomes highlighted, press the SET Button.
User Menus Adjusting Screen Color Picture Mode Picture Picture Mode Color Temperature Advanced Aspect Ratio Picture Reset Screen Vivid Standard Cinema Sport Game User1 User2 MENU Toggles between screen presets. • Vivid : Select this option to display with a sharp image. • Standard : The most general and natural screen display status. • Cinema : Select this option to lower brightness by one level. • Sport : Select this option to display with a soft image.
User Menus Adjusting Screen Color Color Temperature Picture Picture Mode Color Temperature Advanced Aspect Ratio Picture Reset Screen Cool Medium Warm User MENU Color Settings • Cool : Slightly purplish white. • Medium : Slightly bluish white. • Warm : Slightly reddish white. • User : Select this option to use the user-defined settings. User Red Green Blue 0 0 0 MENU Red / Green / Blue Set your own color levels.
User Menus Adjusting Screen Color Advanced Picture Picture Mode Color Temperature Advanced Aspect Ratio Picture Reset Screen To set MENU • Gamma : Set your own gamma value. : -50/0/50 On the monitor, high gamma values display whitish images and low gamma values display high contrast images. • Film Mode : (Function works in the following mode - AV, Component 480i/576i) When you watch a movie, this function adjusts the set to the best picture appearance.
User Menus Adjusting Screen Color Aspect Ratio To select the image size of the screen. Picture Picture Mode Color Temperature Advanced Aspect Ratio Picture Reset Screen 16:9 Original 4:3 14:9 Zoom1 Zoom2 MENU 16:9 Widescreen mode. Just Scan Allows you to enjoy the transmitted data fully without any images cut off. (* This menu is activated only in 720p, 1080p and 1080i in Component mode.) Original The aspect ratio is not adjusted from the original. It is set by the program being watched.
User Menus Adjusting Screen Color Picture Reset Return Picture Mode, Color Temperature, Advanced to the default factory settings. Picture Picture Mode Color Temperature Advanced Aspect Ratio Picture Reset Screen To set MENU Screen Adjust the screen video. Picture Picture Mode Color Temperature Advanced Aspect Ratio Picture Reset Screen Screen To set Auto Config. Manual Config. XGA Mode Reset To set MENU MENU Auto Config.
User Menus Adjusting the audio function Sound Mode The best sound tone quality will be selected automatically depending on the video type that you're currently watching. Audio Sound Mode Auto Volume Balance Speaker Clear Voice Standard Music Cinema Sport Game User MENU • Clear Voice : By differentiating the human sound range from others,it helps users listen to human voices better. • Standard : The most commanding and natural audio.
User Menus Adjusting the timer function Time _ _ : _ _ AM Clock On/Off Timer Sleep Time Auto Sleep Power On Delay MENU Clock If the current time is incorrect, reset the clock manually. button to select the Time menu. 1) Press the MENU button and then use 2) Press the button and then use button to select the Clock menu. 3) Press the button and then use button to set the hour(00~23). 4) Press the button and then use button to set the minutes(00~59).
User Menus Selecting the options Option Language Key Lock ISM Method Power Indicator Logo Light DPM Select Tile Mode Factory Reset To set MENU Language To choose the language in which the control names are displayed. Key Lock Use the buttons to select On or Off. The monitor can be set up so that it can only be used with the remote control. This feature can prevent unauthorized viewing. In order to lock the OSD screen adjustment, set the Key Lock tab to the 'On' position.
User Menus Selecting the options • To use this function - Must be displayed with various other products. - Must be in a function that can be connected to RS-232C or RGB Out Option Tile mode Language Key Lock ISM Method Power Indicator Logo Light DPM Select Tile Mode Factory Reset Tile Mode H-Size V-Size H-Position V-Position Reset Tile ID Natural Off 0 0 <> <> It is used to enlarge the screen and also used with several products to view screen.
User Menus Selecting the options - Tile mode (product 1 ~ 9) : r(3) x c(3) row ID 1 ID 2 ID 3 ID 4 ID 5 ID 6 ID 7 ID 8 ID 9 column - Tile mode (product 1 ~ 2) : r(2) x c(1) row ID 2 ID 1 column - Tile mode (product 1 ~16) : r(4) x c(4) row ID 1 ID 2 ID 3 ID 4 ID 5 ID 6 ID 7 ID 8 column ID 9 ID10 ID 11 ID 12 ID 13 ID 14 ID 15 ID 16 30
User Menus Selecting the options Option Tile mode Language Key Lock ISM Method Power Indicator Logo Light DPM Select Tile Mode Factory Reset Tile Mode H-Size V-Size H-Position V-Position Reset Tile ID Natural Off 0 0 <> <> 1 Off MENU Factory Reset • H-Size Adjust the horizontal size of the screen taking into account the size of the bezel. • V-Size Adjust the vertical size of the screen taking into account the size of the bezel. • H-Position Moving the screen position horizontally.
User Menus Adjust Set ID and check Serial No. and SW version. Information Set ID Serial No. SW Version MENU Set ID You can assign a unique Set ID NO (name assignment) to each product when several products are connected for display. Specify the number (1~99) using the button and exit. Use the assigned Set ID to individually control each product using the Product Control Program. Serial No. This menu shows the serial number of the product. SW Version This menu shows the software version.
Troubleshooting No image is displayed ● Is the product power cord connected? • See if the power cord is properly connected to the outlet. ● Is the power indicator light on? • See if the power switch is turned on. • May need service. ● Power is on, power indicator is blue but • Adjust brightness and contrast again. the screen appears extremely dark. • Backlight may need repair. ● the power indicator amber? • If the product is in power saving mode, move the mouse or press any key.
Troubleshooting The screen image looks abnormal. ● Is the screen position wrong? • D-Sub analog signal – Press the “AUTO” button in the remote control to automatically select the optimal screen status that fits into the current mode. If adjustment is not satisfactory, use the Position OSD menu. • See if the video card resolution and frequency are supported by the product. If the frequency is out of range, set to the recommended resolution in the Control Panel – Display – Setting menu.
Troubleshooting The audio function does not work. ● No sound? • See if the audio cable is connected properly. • Adjust the volume. • See if the sound is set properly. • Select the appropriate equalize sound. ● Sound is too dull. • Adjust the volume. ● Sound is too low. Screen color is abnormal. ● Screen has poor color resolution (16 colors). • Set the number of colors to more than 24 bits (true color) Select Control Panel – Display – Settings – Color Table menu in Windows.
Specifications The product specifications can change without prior notice for product improvement. M4212C LCD Panel Power Dimensions &Weight 42 inches (106.72 cm) TFT (Thin Film Transistor) LCD (Liquid Crystal Display) Panel Visible diagonal size: 106.72 cm 0.681 mm X 0.681 mm (Pixel Pitch) Rated Voltage Power Consumption AC 100-240V~ 50/60Hz 2.2A On Mode : 220W Typ.
Specifications The product specifications can change without prior notice for product improvement. M4712C LCD Panel Power Dimensions &Weight 47 inches (119.295 cm) TFT (Thin Film Transistor) LCD (Liquid Crystal Display) Panel Visible diagonal size: 119.295 cm 0.76125 mm X 0.76125 mm (Pixel Pitch) Rated Voltage Power Consumption AC 100-240V~ 50/60Hz 3.0A On Mode : 300W Typ.
Specifications The product specifications can change without prior notice for product improvement. Video Signal Max. Resolution RGB : 1600 X 1200 @60Hz HDMI/DVI : 1920 X 1080 @60Hz – It may not be supported depending on the OS or video card type. Recommended Resolution RGB : WSXGA 1360 X 768 @60Hz HDMI/DVI : WSXGA 1360 X 768 @60Hz – It may not be supported depending on the OS or video card type.
Specifications PC Mode – Preset Mode Preset mode Horizontal Frequency (kHz) Vertical Frequency (Hz) 640 x 350 720 x 400 640 x 480 640 x 480 800 x 600 800 x 600 832 x 624 1024 x 768 1024 x 768 1280 x 720 31.469 31.468 31.469 37.5 37.879 46.875 49.725 48.363 60.123 44.772 70.8 70.8 59.94 75 60.317 75 74.55 60 75.029 59.
RS-232C Controlling the Multiple Product Use this method to connect several products to a single PC. You can control several products at a time by connecting them to a single PC. Connecting the cable Connect the RS-232C cable as shown in the picture. * The RS-232C protocol is used for communication between the PC and product. You can turn the product on/off, select an input source or adjust the OSD menu from your PC.
RS-232C Controlling the Multiple Product Command Reference List 01. Power 02. Input Select 03. Aspect Ratio 04. Screen Mute 05. Volume Mute 06. Volume Control 07. Contrast 08. Brightness 09. Color 10. Tint 11. Sharpness 12. OSD Select 13. Remote Lock/ key Lock 14. Balance 15. Color Temperature 16. Abnomal state 17. ISM mode 18. Auto configuration 19. Key 20. Tile Mode 21. Tile H Size 22. Tile V Size 23. Tile ID Set 24. Natural Mode (In Tilemode) 25. Elapsed time return 26. Temperature value 27.
RS-232C Controlling the Multiple Product Transmission / Receiving Protocol Transmission [Command1][Command2][ ][Set ID][ ][Data][Cr] * [Command 1]: First command. (k) * [Command 2]: Second command.(a ~ u) * [Set ID]: Set up the Set ID number of product. range : 1~99. by setting '0', server can control all products. * In case of operating with more than 2 sets using set ID as '0' at the same time, it should not be checked the ack message.
Controlling the Multiple Product RS-232C Transmission / Receiving Protocol ▲ 01. Power(Command : a) To control Power On/Off of the Set. Transmission [k][a][ ][Set ID][ ][Data][Cr] Data 0 : Power Off 1 : Power On Acknowledgement [a][ ][Set ID][ ][OK][Data][x] ▲ To show the status of Power On/Off. Transmission [k][a][ ][Set ID][ ][FF][Cr] Acknowledgement [a][ ][Set ID][ ][OK][Data][x] Data 0 : Power Off 1 : Power On ▲ 02.
RS-232C Controlling the Multiple Product Transmission / Receiving Protocol ▲ 03. Aspect Ratio(Command : c) (Main picture format) To adjust the screen format. You can also adjust the screen format using the ARC (Aspect Ratio Control) button on remote control or in the Screen menu.
RS-232C Controlling the Multiple Product Transmission / Receiving Protocol ▲ 05. Volume Mute(Command : e) To control On/Off of the Volume Mute. Transmission [k][e][ ][Set ID][ ][Data][Cr] Data 0 : Volume Mute On (Volume Off) 1 : Volume Mute Off (Volume On) Acknowledgement [e][ ][Set ID][ ][OK][Data][x] Data 0 : Volume Mute On (Volume Off) 1 : Volume Mute Off (Volume On) ▲ 06. Volume Control(Command : f) To adjust Volume .
RS-232C Controlling the Multiple Product Transmission / Receiving Protocol ▲ 07. Contrast(Command : g) To adjust screen contrast. You can also adjust the contrast in the Picture menu. Transmission [k][g][ ][Set ID][ ][Data][Cr] Data Min : 00H ~ Max : 64H • Refer to ‘Real data mapping’ as shown below. Acknowledgement [g][ ][Set ID][ ][OK][Data][x] * Real data mapping 0 : Step 0 : A : Step 10 : F : Step 15 10 : Step 16 : 64 : Step 100 ▲ 08. Brightness(Command : h) To adjust screen brightness.
RS-232C Controlling the Multiple Product Transmission / Receiving Protocol ▲ 09. Color(Command : i) (Video only) To adjust the screen color. You can also adjust the color in the Picture menu. Transmission [k][i][ ][Set ID][ ][Data][Cr] Data Min : 00H ~ Max : 64H (Hexadecimal code) • Refer to ‘Real data mapping’ page A7. Acknowledgement [i][ ][Set ID][ ][OK][Data][x] Data Min : 00H ~ Max : 64H ▲ 10. Tint(Command : j) (Video only) To adjust the screen tint.
Controlling the Multiple Product RS-232C Transmission / Receiving Protocol ▲ 11. Sharpness(Command : k) (Video only) To adjust the screen Sharpness. You can also adjust the sharpness in the Picture menu. Transmission [k][k][ ][Set ID][ ][Data][Cr] Data Min : 00H ~ Max : 64H (Hexadecimal code) • Refer to ‘Real data mapping’ page A7. Acknowledgement [k][ ][Set ID][ ][OK][Data][x] Data Min : 00H ~ Max : 64H ▲ 12. OSD Select(Command : l) To control OSD on/off to the set.
RS-232C Controlling the Multiple Product Transmission / Receiving Protocol ▲ 14 Balance(Command : t) To adjust the sound balance. Transmission [k][t][ ][Set ID][ ][Data][Cr] Data Min : 00H ~ Max : 64H (Hexadecimal code) • Refer to ‘Real data mapping’ page A7. Acknowledgement [t][ ][Set ID][ ][OK][Data][x] Data Min : 00H ~ Max : 64H * Balance : L50 ~ R50 ▲ 15. Color Temperature (Command : u) To adjust the screen color temperature.
RS-232C Controlling the Multiple Product Transmission / Receiving Protocol ▲ 16. Abnomal state (Command : z) Abnormal State : Used to Read the power off status when Stand-by mode.
RS-232C Controlling the Multiple Product Transmission / Receiving Protocol ▲ 18. Auto Configure(Command: j u) To adjust picture position and minimize image shaking automatically. it works only in RGB(PC) mode. Transmission [j][u][ ][Set ID][ ][Data][Cr] Data 1 : To set Acknowledgement [u][ ][Set ID][ ][OK][Data][x] ▲ 19. Key(Command : m c) To send IR remote key code. Transmission [m][c][ ][Set ID][ ][Data][Cr] Data Key code : Refer to page A18.
RS-232C Controlling the Multiple Product Transmission / Receiving Protocol ▲ 20. Tile Mode(Command : d d) Change a Tile Mode. Transmission [d][d][][Set ID][][Data][x] Data Description 00 Tile mode is off. 12 1 x 2 mode(column x row) 13 1 x 3 mode 14 1 x 4 mode ... ... 55 5 x 5 mode * The data can not be set to 0X or X0 except 00.
RS-232C Controlling the Multiple Product Transmission / Receiving Protocol ▲ 21. Tile H Size(Command : d g) To set the Horizontal size. Transmission [d][g][][Set ID][][Data][x] Data Min : 00H ~ Max : 64H Acknowledgement [g][][Set ID][][OK/NG][Data][x] ▲ 22. Tile V Size(Command : d h) To set the Vertical size.
RS-232C Controlling the Multiple Product Transmission / Receiving Protocol ▲ 23. Tile ID Set(Command : d i) To assign the Tile ID for Tiling function . Transmission [d][i][][Set ID][][Data][x] Data Min : 00H ~ Max : 19H (Hexadecimal code) Acknowledgement [i][][Set ID][][OK/NG][Data][x] ▲ 24 Natural Mode (In Tilemode) (Command : d j) The image is omitted by the distance between the screens to be naturally shown.
RS-232C Controlling the Multiple Product Transmission / Receiving Protocol ▲ 26. Temperature value (Command : d n) To read the inside temperature value. Transmission [d][n][][Set ID][][Data][x] * The data is always FF(in Hex). Acknowledgement [n][][Set ID][][OK/NG][Data][x] * The data is 1 byte long in Hexadecimal. ▲ 27. Lamp fault Check(Command : d p) To check lamp fault. Transmission [d][p][][Set ID][][Data][x] * The data is always FF(in Hex).
RS-232C Controlling the Multiple Product Transmission / Receiving Protocol ▲ 28. Auto volume (Command : d u) Automatically adjust the volume level. Transmission [d][u][][Set ID][][Data][x] Data 0 : Off 1 : On Acknowledgement [u][][Set ID][][OK/NG][Data][x] ▲ 29. Speaker (Command : d v) Turn the speaker on or off.
RS-232C Controlling the Multiple Product Transmission / Receiving Protocol ▲ 30. Time (Command : f a) Set the current time. Transmission [f][a][][Set ID][][Data1][][Data2][][Data3][Cr] [Data1] 0 : Monday 1: Tuesday 2 : Wednesday 3 : Thursday 4 : Friday 5 : Saturday 6 : Sunday [Data2] 0H~17H (Hours) [Data3] 00H~3BH (Minutes) Acknowledgement [a][][Set ID][][OK/NG][Data1][Data2][Data3][x] *When reading data, FFH is inputted for [Data1], [Data2] and [Data3]. In other cases, all are treated as NG.
RS-232C Controlling the Multiple Product Transmission / Receiving Protocol ▲ 31. On Timer (On/Off Timer) On, Off (Command : F b) Set days for On Timer.
RS-232C Controlling the Multiple Product Transmission / Receiving Protocol ▲ 33. On Timer (On/Off Timer) Time (Command : f d) Set On Timer. Transmission [f][d][][Set ID][][Data1][][Data2][Data3][Cr] [Data1] 0 : Monday 1: Tuesday 2 : Wednesday 3 : Thursday 4 : Friday 5 : Saturday 6 : Sunday 7 : Everyday [Data2] 00H~17H (Hours) [Data3] 00H~3BH (Minutes) Acknowledgement [d][][Set ID][][OK/NG][Data1][Data2][Data3][x] *When reading data, FFH is inputted for [Data2], [Data3].
RS-232C Controlling the Multiple Product Transmission / Receiving Protocol ▲ 34. Off Timer (On/Off Timer) Time (Command : f e) Set Off Timer. Transmission [f][e][][Set ID][][Data1][][Data2][][Data3][Cr] [Data1] 0 : Monday 1: Tuesday 2 : Wednesday 3 : Thursday 4 : Friday 5 : Saturday 6 : Sunday 7 : Everyday [Data2] 00H~17H (Hours) [Data3] 00H~3BH (Minutes) Acknowledgement [e][][Set ID][][OK/NG][Data1][Data2][Data3][x] *When reading data, FFH is inputted for [Data2], [Data3].
RS-232C Controlling the Multiple Product Transmission / Receiving Protocol ▲ 35. Sleep Time (Command : f f) Set Sleep Time. Transmission [f][f][][Set ID][][Data][Cr] Data 0 : Off 1 : 10 2 : 20 3 : 30 4 : 60 5 : 90 6 : 120 7 : 180 8 : 240 (Orderly) Acknowledgement [f][][Set ID][][OK/NG][Data][x] ▲ 36. Auto Sleep (Command : f g) Set Auto Sleep.
RS-232C Controlling the Multiple Product Transmission / Receiving Protocol ▲ 37. Power On Delay (Command : f h) Set the schedule delay when the power is turned on (Unit: second). Transmission [f][h][][Set ID][][Data][Cr] Data : 00H ~ 64H (Data value) Acknowledgement [h][][Set ID][][OK/NG][Data][x] ▲ 38. Language (Command : f i) Set the OSD language.
RS-232C Controlling the Multiple Product Transmission / Receiving Protocol ▲ 39. DPM Select (Command : f j) Set the DPM (Display Power Management) function. Transmission [f][j][][Set ID][][Data][Cr] Data 0 : Off 1: On Acknowledgement [j][][Set ID][][OK/NG][Data][x] ▲ 40. Reset (Command : f k) Execute the Picture, Screen and Factory Reset functions.
RS-232C Controlling the Multiple Product Transmission / Receiving Protocol ▲ 41. S/W Version (Command : f z) Check the software version. Transmission [f][z][][Set ID][][Data][Cr] Data FFH : Read Acknowledgement [z][][Set ID][][OK/NG][Data][x] ▲ 42. Input Select (Command : x b) To select input source for the Set.
IR Codes RS-232C ▲ How to connect Connect your wired remote control to Remote Control port on the Product. ▲ Output waveform Remote Control IR Code single pulse, modulated with 37.
IR Codes RS-232C Note ▲ R/C Button ▼ R/C Button ▲ 00 01 02 03 08 C4 C5 09 98 0B 0E 43 5B 6E 44 10 11 12 13 14 15 16 17 18 19 5A BF D4 D5 C6 79 76 77 AF 99 Function VOL( ) R/C Button ▲ Code(Hexa) VOL( ) R/C Button POWER ON/OFF R/C Button (Power On/Off) POWER ON Discrete IR Code(Only Power On) POWER OFF Discrete IR Code(Only Power On) MUTE R/C Button AV INPUT SLEEP MENU EXIT PSM SET R/C Button Number Key 0 R/C Button Number Key 1 R/C Button Number Key 2 R/C Button Number Key 3 R
