User's Guide M4224N Make sure to read the Safety Precautions before using the product. Keep the User's Guide(CD) in an accessible place for future reference. S ee the label attached on the product and give the information to your dealer when you ask for service. Important WARRANTY VOID IF REMOVED Warranty void if removed. 3850TAZ209Y Temporary noise is normal when powering ON or OFF this device. WARNING -This is a class A product.
Connecting the stand - Only on some models. 1. Tpicture. ake the parts for the stand out of the box and assemble them as shown in the Parts First, check if the following parts are all present. Screws (4) 2. 3. Stand (2) lace a soft cloth on the table and put the product with the screen facing downP ward. Connect the stand as shown in the following picture. se the screws to secure the stand on the rear side of the product as shown in U the diagram.
Connecting the Speakers - Only on some models. Mount the product onto the speaker by using a screw as shown in the following connect the speaker cable. After installing your speakers, use holders and cable ties to organize the speaker cables. Cable holder Remove the paper. * This feature is not available in all model. Cable tie When the speaker is installed. *Connect the input terminal with a proper color match. * This feature is not available in all model.
Using the Remote Control Name of the Remote Control Buttons ▪ Power On/Off Button ▪ Input Select Button (See next page) There is not a function which is supported There is not a function which is supported ▪ CTR.PWR Button Turn on the power of the PC built in the monitor and then turn off. (The CTR.PWR function operates only when the PC Control menu is off.) 1 2 3 4 5 6 7 8 9 CTR. PWR 0 ▪ ARC button To select the image size of the screen.
Using the Remote Control ▪ Input Select Button If you press the button once, the following Input Signal Window will appear. Select the signal type you want using the ▼▲ button. 1 2 3 INPUT 4 5 6 RGB DVI 7 8 9 CTR. PWR 0 * Inserting batteries into remote control. 1. Take out the battery cap. 2. Insert the batteries with correct polarity (+/-). 3. Close the battery cap. ▪ Dispose of used batteries in the recycle bin to prevent environmental pollution.
ERIAL PORT Name and Function of the Parts * The product image in the user’s guide could be different from the actual image.
Connecting to External Devices When Connecting to your Built in PC When connecting with the DVI signal input 1. Rear side of the product. RS-232C (CONTROL) OUT DVI IN RGB IN RGB OUT AUDIO (RGB/DVI) REMOTE CONTROL IN LAN USB USB H/PHONE OUT MIC IN SP/DIF SERIAL PORT RGB OUT IN Connect the power cord. 2. Turn on power by pressing the power button on the product. SOURCE MENU SOURCE 3. AUTO/SET Power button AUTO/SET Select an input signal.
Connecting to External Devices RS-232C (CONTROL) OUT DVI IN RGB IN RGB OUT AUDIO (RGB/DVI) USB USB H/PHONE OUT MIC IN RS-232C (CONTROL) SP/DIF SERIAL PORT OUT RGB OUT When connecting with the D-Sub signal input cable. 1. RGB IN DVI IN RGB OUT AUDIO (RGB/DVI) LAN REMOTE CONTROL IN H/PHONE OUT USB USB MIC IN SP/DIF RGB OUT SERIAL PORT IN Rear side of the product.
Connecting to External Devices 5. 1 1 2 6. 3 4 2 Move the mouse pointer to an empty area on the Windows screen (with no icons or task bars) and click the right mouse button. When the pop-up menu appears, click the ‘Graphics Options' menu. 3 click the 'Output To' menu. 4 click the 'Monitor' menu. Select an input signal. Press the INPUT button on the remote control to select the input signal.
Connecting to External Devices * In order to convert the RGB signal to the DVI signal 1. 1 1 2 2. 2 3 4 Move the mouse pointer to an empty area on the Windows screen (with no icons or task bars) and click the right mouse button. When the pop-up menu appears, click the 'Graphics Options' menu. 3 Click the 'Output To' menu. 4 Click the 'Digital Display' menu. Select an input signal. Press the INPUT button on the remote control to select the input signal.
RGB IN GB OUT Connecting to External Devices When Connecting to your PC DVI IN RS-232C (CONTROL) OUT RGB IN RGB OUT AUDIO (RGB/DVI) LAN REMOTE CONTROL IN H/PHONE OUT USB USB MIC IN SP/DIF SERIAL PORT RGB OUT IN 1. First of all, see if the computer, product and the peripherals are turned off. Then, connect the signal input cable.
Connecting to External Devices 2. 1 Turn on power by pressing the power button on the product. SOURCE MENU SOURCE AUTO/SET Power button AUTO/SET 2 Turn on the PC. 3. Select an input signal. Press the INPUT button on the remote control to select the input signal. INPUT SET INPUTthe SOURCE button SET at the back side of the product. Or, press SOURCE AUTO/SET SOURCE AUTO/SET A When connecting with a D-Sub signal input cable. ▪ Select RGB : 15-pin D-Sub analog signal.
Connecting to External Devices Watching RGB Outputs Use this function when displaying ANALOG RGB inputs of a PC to the other product. ▪ To use different products connected to each other Connect one end of the signal input cable(15-pin D-Sub Signal Cable) to the RGB OUT connector of product 1 and connect the other end to the RGB IN connector of other products.
Selecting and Adjusting the Screen Name of the Buttons in the Screen Adjustment Unit SOURCE SOURCE SOURCE AUTO/SET ON/OFF AUTO/SET AUTO/SET Pivot model Only SOURCE SOURCE MENU MENU SOURCE MENU SOURCE AUTO/SET AUTO/SET AUTO/SET AUTO/SET 13
Selecting and Adjusting the Screen Power Button ▪P ress this button to turn on the power. Press this button again to turn it off. Power Indicator ▪ This Indicator lights up blue when the display operates normally(on mode). If the display is in sleep (Power Saving) mode, this indicator color changes to amber. MENU Button ▪U se this button to show/hide the OSD (On Screen Display) menu screen. OSD Select / Adjust Button ▪ Use this button to select an icon or adjust the setting in the OSD screen.
Selecting and Adjusting the Screen OSD Menu Icon Function Description Adjusts screen brightness, contrast and color that you prefer. PICTURE Adjusts the audio function. SOUND Adjust the time function TIMER Adjusts the screen status according to the circumstances. SPECIAL Adjusts the screen video. SCREEN Nota ▪ OSD (On Screen Display) The OSD function enables you to adjust the screen status conveniently since it provides graphical presentation.
Selecting and Adjusting the Screen How to adjust the OSD (On Screen Display) screen Pops up the menu screen Move where you want to adjust Move where you want to adjust Select a menu icon Select a menu icon Adjust the status Save adjustment Exit from the menu screen. ▪ Use the remote control to adjust the OSD screen. 1 Press the MENU Button, then the main menu of the OSD appears. 2 To access a control, use the 3 When the icon you want becomes highlighted, press the SET Button.
Selecting and Adjusting the Screen Adjusting Screen Color CSM ▪ 6500K/9300K Selecting a factory setting color set. 6500K: Slightly reddish white. 9300K: Slightly bluish white. CSM CSM ▪ User : S elect this option to use the user-defined settings. Contrast To adjust the contrast of the screen. Brightness To adjust the brightness of the screen. Red / Green / Blue Set your own color levels.
Selecting and Adjusting the Screen Adjusting the audio function SSM The best sound tone quality will be selected automatically depending on the video type that you're currently watching. SOUND SSM Flat Balance Music Movie Sports User SOUND ▪ ▪ ▪ ▪ ▪ SSM Flat Balance Music Movie Flat : The most commanding Sports and natural audio. SOUND Music : Select this optionUser to enjoy the original sound when listening to the music. SSM Movie : Select this option to enjoy sublime sound.
Selecting and Adjusting the Screen TIME ID to adjust the time function TIMER Clock MNT Off timer MNT On timer PC Off timer PC On timer Clock This function is used to set up of current time. You must set the time correctly before using On/Off time function. 1) Press the MENU button and then use button to select the TIMER menu. 2) Press the button and then use button to select the Clock menu. 3) Press button and then use button to set the hour(00~23).
Selecting and Adjusting the Screen Selecting the options Reset Reset Input If you press the button once, the following Input Signal Window will appear. Select the signal type you want using the button. Reset Reset Tile mode Off Child lock Use the buttons to select can be set H-Size On or Off. The Set Tile mode Off up so that it can only be used with the remote control. This0 feature can prevent unauthorized viewing.
Reset Selecting and Adjusting the Screen Selecting the options ▪ To use this function - You can connect the product with several other products and use the Tile mode function. Reset Tile mode Tile mode It is used to enlarge the screen and also used with several products to view screen, Off H-Size 0 V-Size 0 H-Position Reset V-Position Reset ID ▪ Tile mode Tile mode and choose Tile alignment and set the ID of the current product to set location.
Selecting and Adjusting the Screen Selecting the options ▪ Tile mode - Tile mode : row x column ( r = 1, 2, 3, 4 c = 1, 2, 3, 4) - 4 x 4 available. - Configuration of an integration screen is also available as well as configuration of one by one Display.
Reset Selecting and Adjusting the Screen Selecting the options ▪ Tile mode (product 1 ~ 2) : r(2) x c(1) Reset row ID1 ID2 Tile mode Off H-Size column 0 V-Size 0 H-Position Reset V-Position Reset Use this function to reset the product to the factory default. However, language selection and PC Control selection Reset will not be initialized. ID Set ID Set ID PC Control You can assign a unique Set ID NO (name assignment) to each product when several products are connected for display.
Selecting and Adjusting the Screen Adjusting Screen CLOCK/PHASE and Position Auto-configure Auto-configure ARC To select the image size of the screen. (1:1 menu are not supported over 1920 X 1080 resolution) Auto-configure Auto-configure Auto-configure Autoconfigure This button is for the automatic adjustment of the screen position, clock and phase. This function is suitable for analog signal input only.
Troubleshooting No image is displayed ● Is the product power cord connected? ▪S ee if the power cord is properly connected to the outlet. ● Is the power indicator light on? ▪ See if the power switch is turned on. ●P ower is on, power indicator is green but the screen appears extremely dark. ▪ Adjust brightness and contrast again. ● Is the power indicator amber? ▪ I f the product is in power saving mode, move the mouse or press any key.
Troubleshooting The screen image looks abnormal. ● I s the screen position wrong at the RGB mode? ▪ Press the "AUTO" button in the remote control to automatically select the optimal screen status that fits into the current mode. If adjustment is not satisfactory, use the Position OSD menu. ▪ See if the video card resolution and frequency are supported by the product. If the frequency is out of range, set to the recommended resolution in the Control Panel " Display " Setting menu.
Troubleshooting 'Child lock on' message appears. ● The 'Child lock on' message appears when pressing the Menu button. Push the MENU button on the remote control and set Child lock to the b position. After-image appears on the product. ● After-image appears when the product is turned off. ▪ I f you use a fixed image for a long time, the pixels may be damaged quickly. Use the screensaver function. Screen color is abnormal. ● Screen has poor color resolution (16 colors).
Specifications The product specifications can change without prior notice for product improvement. LCD Panel 42.02 inches (106.73 cm) TFT (Thin Film Transistor) LCD (Liquid Crystal Display) Panel Anti-Glare coating Visible diagonal size: 106.73 cm 0.4845 mm x 0.4845 mm (Pixel Pitch) Power Rated Voltage AC 100-240V~ 50/60Hz 3.0A Power Consumption On Mode : 300W Typ.(With PC), 240W Typ.
Specifications The product specifications can change without prior notice for product improvement. Video Signal Max. Resolution RGB : 1920 X 1080 @60Hz DVI : 1920 X 1080 @60Hz - It may not be supported depending on the OS or video card type. Recommended Resolution RGB : 1920 X 1080 @60Hz DVI : 1920 X 1080 @60Hz - It may not be supported depending on the OS or video card type.
Specifications PC Mode ─ Preset Mode Preset mode Horizontal Frequency (kHz) Vertical Frequency (Hz) 1 640 x 480 31.469 59.94 2 800 x 600 37.879 60.317 3 1024 x 768 48.363 60 4 1280 x 1024 63.981 60.02 5 1920 x 1080 67.
Specifications VESA wall mounting Connected to another object (stand type and wall-mounted type.) This product accepts a VESA-compliant mounting interface pad.- (This has to be purchased separately if required.) For further information, refer to the VESA Wall Mounting Instruction Guide. Kensington Security Slot- (This has to be purchased separately if required.
TE L IN Specifications Connecting the USB(Universal Serial Bus) Cable "USB (Universal Serial Bus)" is an innovation in connecting your different desktop peripherals conveniently to your computer. By using the USB, you will be able to connect your mouse, keyboard, and other peripherals to your display instead of having to connect them to your computer. This will give you greater flexibility in setting up your system.
Controlling the Multiple Product RS-232C Use this method to connect several products to a single PC. You can control several products at a time by connecting them to a single PC. Connecting the cable Connect the RS-232C cable as shown in the picture. * The RS-232C protocol is used for communication between the PC and product. You can turn the product on/off, select an input source or adjust the OSD menu from your PC.
RS-232C Controlling the Multiple Product Command Reference List 01. Power 02. Main Input Select 03. Aspect Ratio 04. Screen Mute 05. Volume Mute 06. Volume Control 07. Contrast 08. Brightness 09. OSD Select 10. Remote On/Off 11. Balance 12. Select Color Temp 13. Auto Configure 14. Red Gain Adjust 15. Green Gain Adjust 16. Blue Gain Adjust 17. Tiling Mode 18. Tile H Position 19. Tile V Position 20. Tile H Size 21. Tile V Size 22. Tile ID Set 23. Temperature Check 24. Inverter Adjust 25. PC Power On/Off 26.
RS-232C Controlling the Multiple Product Protocollo trasmissione / ricezione Transmission [Command1][Command2][ ][Set ID][ ][Data][Cr] * [Command 1]: First command. (k) * [Command 2]: Second command. (a ~ u) * [Set ID]: You can adjust the set ID to choose desired product ID number in Special menu. Adjustment range is 1 ~99. When selecting Set ID ‘0’, every connected set is controlled. Set ID is indicated as decimal (1~255) on menu and as Hexa decimal (0x0~0x64) on transmission/receiving protocol.
RS-232C Controlling the Multiple Product Protocollo trasmissione / ricezione 01. Power On(Command : a) ►To control Power On/Off of the Set. Transmission [k][a][ ][Set ID][ ][Data][Cr] Data 0 : Power Off 1 : Power On ff: Read Status Acknowledgement [a][ ][Set ID][ ][OK][Data][x] ►To show the status of Power On/Off.
RS-232C Controlling the Multiple Product Protocollo trasmissione / ricezione 03. Aspect Ratio(Command : c) (Main picure format) ► To adjust the screen format. You can also adjust the screen format using the ARC (Aspect Ratio Control) button on remote control or in the Screen menu. Transmission [k][c][ ][Set ID][ ][Data][Cr] Data 8 : Full mode 9 : 1:1 (Operates only if current resolution is less than recommended resolution. ) Acknowledgement [c][ ][Set ID][ ][OK][Data][x] 04.
RS-232C Controlling the Multiple Product Protocollo trasmissione / ricezione 05. Volume Mute(Command : e) ► To control On/Off of the Volume Mute. Transmission [k][e][ ][Set ID][ ][Data][Cr] Data 0 : Volume Mute On (Volume Off) 1 : Volume Mute Off (Volume On) Acknowledgement [e][ ][Set ID][ ][OK][Data][x] Data 0 : Volume Mute On (Volume Off) 1 : Volume Mute Off (Volume On) 06. Volume Control(Command : f) ► To adjust Volume.
RS-232C Controlling the Multiple Product Protocollo trasmissione / ricezione 07. Contrast(Command : g) ► To adjust screen contrast. You can also adjust the contrast in the Picture menu. Transmission [k][g][ ][Set ID][ ][Data][Cr] Data Min : 00H ~ Max : 64H ·Refer to ‘Real data mapping’ as shown below. Acknowledgement [g][ ][Set ID][ ][OK][Data][x] * Real data mapping 0 : Step 0 : A : Step 10 : F : Step 15 10 : Step 16 : 64 : Step 100 08. Brightness(Command : h) To adjust screen brightness.
RS-232C Controlling the Multiple Product Protocollo trasmissione / ricezione 09. OSD Select(Command : l) ► To control OSD on/off to the set when RS-232C Commands are transmitted. Transmission [k][l][ ][Set ID][ ][Data][Cr] Data 0 : OSD Off 1 : OSD On Acknowledgement [l][ ][Set ID][ ][OK][Data][x] Data 0 : OSD Off 1 : OSD On 10. Remote On/Off (Command : m) ► Lock the buttons at the rear side of the monitor and the button at the remote control.
RS-232C Controlling the Multiple Product Protocollo trasmissione / ricezione 12. Select Color Temp (Command : u) ► To adjust the screen color temperature. Transmission [k][u][ ][Set ID][ ][Data][Cr] Data 0 : User 1 : 9300K 2 : 6500K Acknowledgement [u][ ][Set ID][ ][OK][Data][x] Data 0 : User 1 : 9300K 2 : 6500K 13. Auto Configure(Command: j u) ► To adjust picture position and minimize image shaking automatically. it works only in RGB(PC) mode.
RS-232C Controlling the Multiple Product Protocollo trasmissione / ricezione 14. Red Gain Adjust (Command: j w) ► To adjust Red color level. Transmission [j][w][ ][Set ID][ ][Data][Cr] Data Min : 00H ~ Max : 64H Acknowledgement [w][ ][Set ID][ ][OK][Data][x] * When it is executed with the 6500K or 9300K selected, it is automatically changed to the USER. 15. Green Gain Adjust (Command: j y) ► To adjust Green color level.
Controlling the Multiple Product RS-232C Protocollo trasmissione / ricezione 17. Tiling Mode (Command :d d) ► Change a Tiling Mode.. Transmission [d][d][ ][Set ID][ ][Data][Cr] Data Description 00 Tiling mode is off. 12 1 x 2 mode(column x row) 13 1 x 3 mode 14 1 x 4 mode ... ... 44 4 x 4 mode * The data can not be set to 0X or X0 except 00. Acknowledgement [d][ ][00][ ][OK/NG][Data][x] 18. Tile H Position (Command : d e) ► To set the horizontal position.
RS-232C Controlling the Multiple Product Protocollo trasmissione / ricezione 19. Tile V Position(Command : d f) ► To set the Vertical position. Transmission [d][f][][Set ID][][Data][x] * The data range is from 00 to 64(in Hex). Acknowledgement [f][][Set ID][][OK/NG][Data][x] 20. Tile H Size(Command : d g) ► To set the Horizontal size. Transmission [d][g][][Set ID][][Data][x]] * The data range is from 00 to 64(in Hex). Acknowledgement [g][][Set ID][][OK/NG][Data][x] 21.
RS-232C Controlling the Multiple Product Protocollo trasmissione / ricezione 22. Tile ID Set (Command : d i) ► To assign the Tile ID for Tiling function. Transmission [d][i][][Set ID][][Data][x] * The data range is from 00 to 10 tile mode. (in Hex). Acknowledgement [i][][Set ID][][OK/NG][Data][x] 23. Temperature check (Command : d n) ► To read the inside temperature value. Transmission [d][n][][Set ID][][Data][x] * The data is always FF(in Hex).
RS-232C Controlling the Multiple Product Protocollo trasmissione / ricezione 25. PC Power On/Off (Command : d s) ► To turn On and Off the built in PC. Transmission [d][s][][Set ID][][Data][x] Data 0 : PC Power Off 1 : PC Power On Acknowledgement [s][][Set ID][][OK/NG][Data][x] *This operates only when ‘PC Control’ is ‘Off’. 26. PC Control On/Off (Command : d t) ► It sets the synchronized power on/off between the built-in PC of the monitor and the monitor.
IR Codes RS-232C How to connect ► Connect your wired remote control to Remote Control port on the Product. Remote Control IR Code ► Output waveform single pulse, modulated with 37.
RS-232C Code(Hexa) Controlling IR theCodes Multiple Product Function Note 00 ▲ R/C Button 01 ▼ R/C Button 02 VOL( ► ) R/C Button 03 VOL( ◄ ) R/C Button 08 POWER ON/OFF R/C Button (Power On/Off) C4 POWER ON Discrete IR Code(Only Power On) C5 POWER OFF Discrete IR Code(Only Power On) 09 MUTE R/C Button 0B INPUT R/C Button 43 MENU R/C Button 5B EXIT R/C Button 44 SET R/C Button 10 Number Key 0 R/C Button 11 Number Key 1 R/C Button 12 Number Key 2 R/C Button 13 N
EWF (Enhanced Write Filter) function Definition - Write protect function for more than one partition - This is the function to protect the partition by returning to original condition prior to the installation once rebooted after the data has been recorded or program installed How to set -D ouble click on the [EWF Enable] file in the [EWF] folder from the desktop and set to protect after auto reboot.
EWF (Enhanced Write Filter) function How to cancel -D ouble click the [EWF Disable] file in the [EWF] folder, and the DOS Window will be displayed to cancel the protection in 5 seconds. Double Click *Setting from DOS mode [Start] ► [Run] ► [cmd] ► [-commitanddisable -live] How to check the current EWF condition [Start] ► [Run] ► [cmd] ► [ewfmgr c:] ► Will be displayed as Enable or Disable.
Windows backup and recovery using LG Smart Recovery When Backing up the current OS from Windows 1. Select [Start] ► [LG Smart Recovery] 2. S elect 'System Backup' ► Designate back up location to [D:] (Do not select C: as it is where the OS is installed) ► After checking the file content, select 'OK' 3. W indows will automatically be rebooted ► Enter System Recovery Mode in DOS mode ► System backup will automatically start. 4.
Windows backup and recovery using LG Smart Recovery When Restoring the current OS from Windows 1. Select 'System Restore' ► Select after checking the backup file from LG Smart Recovery (Factory image: Initial factory default image) (Backup.LBI: User created image) 2.
Windows backup and recovery using LG Smart Recovery When Restoring the current OS from Windows (When Windows cannot be booted) 1. When booting the system, press F11 on the keyboard to enter the Restore mode 2. Select 'System Restore' ► S elect the backup file from LG Smart Recovery (Factory image: Initial factory default image) (Backup.LBI: User created image) ► After checking the image to restore, click on 'OK' 3.
Limitation of Windows embedded XP Limitation related to the installation of Microsoft Office Embedded limitation of Microsoft Korean XP (Korean) - When you run Full Screen (Alt+Enter) from the DOS window, the font can be broken. - When saving the file with a different name from the Print window, the name of the menu window is displayed in English. - When moving to the detail menu item of Control panel etc., some menus are displayed in English (HyperTerminal, Language setting by country etc.
