ENGLISH DEUTSCH NEDERLANDS MAX220UB / MAX221UB ITALIANO Please read this manual carefully before operating your set and retain it for future reference.
Getting Started Safety Information CAUTION 1 RISK OF ELECTRIC SHOCK DO NOT OPEN or any functions. Pull over in a safe and legal manner before attempting such operations. Do not use for many hours at extremely low or high temperature. (-10 °C to 60 °C) Getting Started CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Table of Contents Disposal of your old appliance 1.When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC. Table of Contents 1 Getting Started 2. All electrical and electronic products shall be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities. 2 4 4 3.
Getting Started l W/S - Moves to the previous or next preset station in TUNER - Moves 10 MP3 / WMA files backward or forward if there is no folder or one folder on an USB. - Moves to the previous or next folder if there are more than 2 folders on an USB. Front panel 1 Remote control (Optional) Getting Started m EQ • 3D Improves sound quality. - When pressed, selects the EQ function. - When pressed and held, selects the 3D SOUND function. a SRC / • OFF - When pressed, selects function sources.
Connecting h c/v Skip / Search / Seek / Tune Battery Installation Installation Type 1 i DISP - Press it, you can check the clock time. - Press and hold it, you can turn on/ off the display window and the light of LED buttons. j RPT Repeats playback. Basic Installation Before installing, make sure that the ignition-switch is set to OFF and remove the terminal of the car battery to avoid short-circuiting. 1. Remove the rear support from the unit. 2. Remove the control panel and trim ring from the unit.
Connecting About detachable control panel Detaching the control panel 1. Press the 6 to open the control panel. Attaching the control panel 2. Lift the control panel slightly. 3. Push the control panel to right. 2 Connecting 1. Align the left side of the panel with the stopper. 2. Push the right side of panel into the unit until it clicks. 5 6 4. Pull the control panel out of the unit. > Caution The control buttons may not work properly if the control panel is not attached properly.
Connecting 7 Connection Connecting to a car Before installing, make sure that the ignition-switch is set to OFF and remove the terminal of the car battery to avoid short-circuiting. Wired remote input (Black): Hard-wired control adapter can be connected. (Optional) To Audio out (Optional) 2 Front Left Front Right Amplifier ab c d ab c d e f g h e f g h Power Antenna > Caution When being connected in a wrong way, the unit displays as follows.
Operating Operation Basic operations 1. Turn the unit on by pressing any key on the unit. 2. Select a source by pressing SRC. 3. Rotate the volume knob to adjust the volume on the unit. Or press VOLUME W / S on the remote control. Turning off the sound temporarily 1. Press MUTE to mute your unit. Or press MUTE on the remote control. 2. Press it again to cancel 3 Using EQ (Equalizer) , Note 3D SOUND is only available when you use the USB. On the unit 1. Press DISP. 2. Press it again to cancel. 1.
Operating For [LIGHT] setting You can adjust the light effects by adjusting DIM, or DIM LV. DIM (Dimmer) OFF / ON : You can change the brightness of the display window during the power-on status. Settings Description DIM ON The display window becomes dark. DIM OFF The display window becomes bright. DIM LV (Dimmer Level) : When you set DIM to ON, you can adjust the dimmer level. (-2, -1, 0, +1, +2) AUX (Auxiliary) ON / OFF It is possible to use auxiliary equipment with this unit.
Operating , Note When a station is stored on the preset numbers on which another station of the same band has already been preset, the previously preset station is automatically erased. Listening to a preset station 3 1. Press BAND repeatedly to select a desired band. 2. Press the volume knob on the unit. Or press ENTER on the remote control. 3. Rotate the volume knob to select a preset station. Or press w / s on the remote control. 4. Press the volume knob. Or press ENTER on the remote control.
Operating Using an USB device 1. Open the USB cover. 2. Connect the USB device. 3. Press SRC repeatedly to select a source to USB. Pausing or restarting USB playback 1. PressT on the unit to pause playback. Or press d/M on the remote control. 2. Press it to resume playback. Searching for a section within a file Skipping to another file Press Y/U on the unit. Or press c / v on the remote control. , Note To skip to previous file, press briefly Y within 3 seconds of playing time.
Troubleshooting Troubleshooting Symptoms Cause Solution Power doesn't turned on. Leads and connectors are not properly. Confirm once more that all connections are correct. The fuse is blown. Rectify the problem that caused the fuse to blow, and then replace it. Be very sure to install the correct fuse with the same rate. Noise and other factors are causing the built in microprocessor to operate incorrectly. Turn the unit off and then on again. Cables are not connected correctly.
Appendix Specifications 13 AUX Frequency Response : 20 Hz to 20 kHz General S / N Ratio : 80 dB Output Power : 53 W x 4 CH (Max.) Distortion : 0.1 % Power Source : DC 12 V Channel Separation (1 kHz) : 45 dB Speaker impedance : 4 Ω Max Input Level (1 kHz) : 1.1 V Ground System : Negative Dimensions (W x H x D) : (178 x 50 x168) mm (without Control Panel) Net Weight : 0.97 kg TUNER FM Tuning Range : 87.5 MHz to 108.0 MHz USB Version : USB 1.1 or USB 2.
